Confirmation of these CLI commands...
Given that I have no development environment, and I only have switches production, is - anyone can confirm the function of these commands?
I have VLAN 10, 20, and 30 defined operation:
config said-> "vlan 10,20,30.
I want to * add * 40 and 50. Is a supercargo command another, or is it a true ADD?
If I run it, "vlan 40,50" will be the config now say, 'vlan 10,20,30,40,50"or will my order supercargo what existed, where now the config looks like,"vlan 40,50? (where the existing VLANs will disappear)?
**************************************************
Second: Same question with the addition of VLAN to a port channel.
My current config has VLAN 10, 20 and 30 on a port channel:
config-> vlan allowed switchport General add 10,20,30
If I add 40 to 50, it is a true ADD, or made an order existing supercargo? When I run it, 'switchport general allowed vlan add 40,50' resulting?
config->
"vlan allowed switchport General add 10,20,30,40,50" (an ADD-ON)
or
"vlan allowed switchport General add 40,50" (a supercargo)
If the config would say then that you question, "vlan 40,50", "vlan 10,20,30,40,50".» The commands add the VLAN to the config. They do not replace the VLAN already configured.
When you issue, 'switchport general allowed vlan add 40,50' ' switchport general allowed vlan add 10,20,30,40,50"sera the result."
Tags: Dell Switches
Similar Questions
-
I'm new to scripting, SLA and EEM and went through the forums and documentation for a couple of days now to learn what I can. I can't get my applet event handler to trigger a reason any. I get the following syslog message based on my reaction als ip config:
4 August 21:25:13.915: % RTT-3-IPSLATHRESHOLD: IP SLAs (100): threshold has occurred for timeout
My setup is less than
!
!
ALS IP 100
2.2.2.2 - echo ICMP-source 1.1.1.1 ip address
threshold of 1000
timeout of 1000
frequency 1
calendar of sla IP 100 now start life forever
reaction-configuration IP SLA 100 respond timeout threshold type 2 5 - type of action trapOnly xofy
!
!Event Manager applet ipsla-ploss
PROACTIVE WAN PACKET LOSS SCRIPT description
event ipsla operation id 100 reaction type timeout
command action 1.0 cli 'enable '.
Action 1.1, "conf t" cli command
Action 1.2 cli command "ip access-list standard bgp-itineraries-in."
action 1.3 cli command "5 deny 5.5.5.5".
action 1.4 cli command "6 deny 6.6.6.6".
Action 1.5 cli command "end".
!
!
Any help is greatly appreciated!
Add the following to your config:
logging of IP sla
activate the IP sla response alerts
-
CLI command to set the power of 1231
Anyone know the CLI command to fine-tune the power on a 1231 AP?
Hi Timothy,.
Maybe it's what you're looking for;
local power
Use the command from the interface of local configuration to configure the access point or bridge of power level of radio. No form of the command to restore the default setting. On the 2.4 GHz radio 802.11 g, you can define orthogonal frequency Division Multiplexing (OFDM) power levels and levels of power complementary Code Keying (CCK). CCK modulation is supported by the devices 802. 11B and 802.11 g. OFDM Modulation is supported by the 802.11 g and 802. peripheral 11A.
Radio 2.4 GHz Access Point (802. 11 (b)
[No] local power {1 | 5 | 20: 30 | 50 | 100 | maximum} 3
Radio 2.4 GHz Access Point (802.11 g)
[No] power local cck {1 | 5 | 10 | 20: 30 | 50 | 100 | maximum} 1
[No] power local cck {-1 | 2 | 5 | 8 | 11: 14 | 15 | 17 | 20: maximum} 4
[No] ofdm local power {1 | 5 | 10: 20: 30: maximum} 1
[No] ofdm local power {-1 | 2 | 5 | 8 | 11: 14: 17 | maximum} 2
5 GHz Access Point Radio (801.11 a)
[No] local power {5 | 10 | 20: 40 | maximum} 1
[No] local power {-1 | 2 | 5 | 8 | 11: 14 | 15 | maximum} 2
[No] local power {-1 | 2 | 5 | 8 | 11: 14 | 15 | 17 | maximum} 2
Note the maximum emission power depends on your regulatory domain and the antenna gain for your access point or bridge. For more information see the "Channels and antenna settings" section of the installation guide hardware for your access point or bridge.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Note the supported transmit power levels on the various points of access and bridges.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Note This command requires radio to be turned on and activated to determine valid power settings allowed on your access point radio.
This doc.
I hope this helps!
Rob
Remember messages useful rate...
-
Cisco ACS 3.1 and Logging of Nortel Passport CLI commands
Good afternoon
We try to log commands CLI Cisco ACS version 3.1 of Nortel Passport 8600. The version of the code that runs on the Passport does not support Ganymede +.
Passports authenticate OK but don't sign any order information. I "think" the problem is maybe that the VSA Radius of Nortel for cli-commands-attribute, 195, is not collected by ACS.
Does anyone know how I would go to get this added to the existing list of Radius (Nortel) VSA?
Thank you very much
Kind regards
Flett.
Foisy,
You must add the attribute Nortel 193-195 to activate the posting of the order.
Unfortunately you can't download on code 3.x, you will need to upgrade acs to the 4.x code.
Kind regards
~ JG
Note the useful messages
-
How to put power on and off through CLI command in ESX Server
Hello
We are facing a problem with VI Client members in VCenter or individual ESX servers.
In this case how properly turned off (or) power on virtual machines through CLI command on the ESX Server.
Any command available for this case.
Kind regards
Eric
On PowerCLI: Take a look at vSphere PowerCLI Administration Guide
Shutdown-VMGuest and Start-VM cmdlets
On vSphere RCLI take a look at vmcontrol.pl
-
What is the CLI commands to monitor a router interface (800 series) 'live '? Watch the increment of packages.
I have provided links to the appropriate documentation. First you will need a basic understanding of the command line Interface (CLI). Then, you can use the commands to enable Capture of integrated package.
Using the command in the Cisco IOS software command-line Interface
-
I try to reset an ap on its values. I can't enter in the cli, but the "Clear wr" command is not available. How to clear the config on this access point?
Also, I have configured initially access point to connect to wlc 4400, which worked great, but when you try to reconfigure the IP address of the CLI is not an option, because the command is disabled.
How to display the running-config on the ap?
This access point can be used as a standalone ap?
Thanks in advance.
Hi Carlos,
Once that the AP has been converted to LWAPP (to work with the WLC) the ability to use the CLI interface is mainly lost. Here is the method to return to autonomous (so it can be used as stand alone);
Returning to standalone Access Point
It is possible to return to a point of access compatible LWAPP Cisco Aironet return to autonomous mode. Please refer to Cisco Aironet Lightweight mode standalone update Access Points to get detailed instructions on the returning to stand-alone mode. Use this URL
Convert a standalone Lightweight Access Point
You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.
By using a TFTP server to revert to a previous version
Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:
--------------------------------------------------------------------------------
Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.
Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.
Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.
Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).
Step 5 disconnect the power to the access point.
Step 6 push the MODE button and hold the button while you reconnect power to the access point.
Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.
Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.
Step 9 after the access point reboots, reconfigure using the GUI or the CLI.
This doc.
Here's the info CLI;
Manually configure the controller information using the CLI of the Access Point
This doc.
I hope this helps!
Rob
Remember messages useful rate...
-
For AP in FlexConnect CLI commands
Hello world
Just as the title says, as much as I Googled it I can't seem to find what are the CLI for AP in FlexConnect commands
I know that we can telnet/ssh to the AP in flexConnect, but what are the possible commands that we run on the AP?
Hope someone can help :DThank you!
This can be useful if you do not see it
HTH
Rasika
Pls note all useful responses *.
-
need for WPA2 Personal Mode CLI commands
I saw this example but I need the CLI generates the GUI. Can anyone help please?
That's what I have to do without the GUI on a 1142N 12.4 running
Configure in personal Mode
The term made personal mode refers to products that are tested to be interoperable in mode PSK only of operation for authentication. This mode requires manual configuration of a PSK on the AP and clients. PSK authenticates users via a password or code identification, both the client station and the AP. No server authentication is required. A client can access the network only if the client password matches the AP password. The password also provides the numbers that TKIP or AES uses to generate an encryption key for encrypting data packets. Personal mode is intended for SOHO environments and is not considered safe for enterprise environments. This section contains the configuration that you need to implement WPA 2 in personal mode.
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}
Hello
Here are the commands for WPA2 personal mode CLI
Configure the terminal
dot11Radio interface 0
encryption ciphers aes - ccm mode
or
encryption mode vlan ciphers aes - ccm< ---="" if="" you="" have="" multiple="">
output
dot11 ssid
open authentication
authentication-key wpa version2 management
WPA - psk ascii
Kind regards
Madhuri
-
Darwin.CLI: most of the cli commands is not available
"View user" command was found but is not currently available (type 'help' then ENTER to learn more about this command)
Spring > list-cloud-tunnels
'List-cloud-tunnels' command was found but is not currently available (type 'help' then ENTER to learn more about this command)
Spring >Thanks for your help, you are right, but I didn't know how to do it. the documentation could be updated to reflect the it. Here's how I work.
Login serverUrl- https://**.**.**.**:8443/darwin - [email protected] - password username *-tenantId tennantnamehere
Thank you
Niasse
-
Is there if a VMS resource pool has enough resources available to start the virtual machine WITHOUT triggering an error of vSphere PowerCLI script - or a series of commands - which can be used to determine?
For reasons of performance test, we use a pool of resources with maximum rates for RAM and CPU. Each virtual machine in the pool has a reservation for CPU and RAM. Test automation will try to start VMs as much as possible in the pool during the test. The CLI will return an error when you start the virtual machine may exceed the amount of allowed resources. When this happens, an error on the console vSphere "insufficient resources". Instead of constantly from the virtual machine, fault and generates error - is there a way to check to see if there is enough space?
Thank you
Jason
Hi Jason,
You can try if the following PowerCLI function is what you need. The function does not resemble stretch bookings.
function Get-VmStartPossible { param($VM) $VM = Get-VM $VM $ResourcePool = $VM | Get-ResourcePool $CpuReservationUsed = $ResourcePool.ExtensionData.Runtime.Cpu.ReservationUsed $VMCpuReservation = $VM.ExtensionData.ResourceConfig.CpuAllocation.Reservation $ResourcePoolCpuLimit = $ResourcePool.ExtensionData.Config.CpuAllocation.Limit $MemoryReservationUsed = $ResourcePool.ExtensionData.Runtime.Memory.ReservationUsed $VMMemoryReservation = $VM.ExtensionData.ResourceConfig.MemoryAllocation.Reservation $ResourcePoolMemoryLimit = $ResourcePool.ExtensionData.Config.MemoryAllocation.Limit*1MB if (($CpuReservationUsed + $VMCpuReservation -gt $ResourcePoolCpuLimit) -or ($MemoryReservationUsed + $VMMemoryReservation -gt $ResourcePoolMemoryLimit)) { $false } else { $true } }
You can call the function with:
Get-VmStartPossible -VM MyVM
-
Unable to understand these linux commands
Hello
I'm new on Linux environment.
Could someone please suggest these orders meaning. These commands are executed when running oracle DB cloning.
* 1.) echo "HOTBACKUP since... $(date"+ %Y%-%m-d % H: % m: %S"))" > > /backup/logs/hotbackup.log 2 > & 1 *.
* $ORACLE_HOME/bin/sqlplus/nolog @ /backup/hot/hotbackup.sql > > /backup/logs/hotbackup.log 2 > & 1 *.
* 2.) echo EI "hot for the remote copy backup file recovery $ (date + % H:%M:%S')\n d % - %m %Y ' > > vi 2 > & 1 *.
Thanks and greetings
MZ
Published by: MZ_AppsDBA on Sep 25, 2012 06:53
Published by: MZ_AppsDBA on Sep 25, 2012 06:53Please always include the version of Oracle and Linux then to ask questions.
Orders means that you must update your cloning procedures.
You should probably avoid using files that have the same names as shell commands. The > vi redirects (create or add) the output of echo in a file named vi and the 2 > & 1 redirects error on stdout output. If you were a file named vi with executable privileges and your current directory in the path or to have some interesting aliasing, you could be the victim of a bad joke when you try to edit a file.
-
WLC cli command "sho memory summary" displays free memory in 2%
It is a licensed for 500 APs 5508 controller and currently 407 APs.
MISTLETOE, (monitor-> summary) shows 69 percent of memory in use.
Should I bother with the release of the memory to see the CLI summary?
(wlc-5600) > see the sum of the memory
-Summary of system memory-
System name: WLC-5600 primary SW Ver: 8.2.121.0
Course time: Tue 4 Oct 14:01:21 2016 system UP time: 52 days 8 hours 59 minutes 17 seconds
NAME: "Chassis", DESCR: "Cisco 5500 Series Wireless LAN Controller.
PID: AIR-CT5508-K9, VID: V01, SN: FCW1502L00N
Total system memory... (1000568 KB) 977 MB
Total free memory in the system... (25280 KB) 24 MB (2%)
Total memory in buffers... (18824 KB)
Total memory cache... (256712 KB) 250 MB
Total Active memory... (786064 KB) 767 MB
Total InActive memory... (122884 KB) 120 MB
Total memory in Pages Anon... (633440 KB) 618 MB
Total memory in the slab... (53200 KB) 51 MB
Total memory in the tables of the Page... (2624 KB) 2 MB
WLC Peak Memory... (1159212 KB) 1132 MB
Virtual memory size WLC... (1150316 KB) 1123 MB
WLC memory resident... (669820 KB) 654 MB
WLC Data memory Segment... (1073480 KB) 1048 MB
Total lot including mapped Pages. (418284 KB) 408 MB
Total memory in pools of Pmalloc... (437076 KB) 426 MB
Total memory used in pools of Pmalloc... (417099 KB) 407 MB
Total free memory in pools of Pmalloc... (15920 KB) 15 MOThank you
Time Stamp....................................... Fri Jul 29 21:43:31 2016
Hold on. The dates DO NOT MATCH with the time of operation of the controller. The time stamp that shows the above there are two falls during July 29, 2016.System Up Time................................... 53 days 3 hrs 42 mins 45 secs
The difference between July 29, 2016 until October 5, 2016 (hour US) is only 68 days. So, this means that about 15 days after that July 29, 2016 he could potentially have been a 'silent crash' with the controller. Cisco has recently published 8.2.130.0 a few days ago. -
Nice day
I try to run the following command through ssh
racadm set the BIOS. BiosBootSettings.BootMode BIOS and I get the following error
ERROR: RAC947: invalid object specified.
Make sure to specify the value according to the type of object.
For more information, see using RACADM.If I don't have racadm get BIOS. BiosBootSettings.BootMode I can see the current value. I try BIOS, bios, Bios but no luck...
Any help?
Can you let me know the iDRAC FW version installed on the server. You need to use following command to set the BIOS boot mode. This command attribute value is case-sensitive
racadm set the BIOS. BiosBootSettings.BootMode Bios
-
allow the launch of the desktop computers only with the view-client CLI commands
Hello
It is possible to restrict desktop graphical clients (web and non-web) launch and the launch of single command line interface?
what I want to achieve this, is to restrict access to desktop computers to view associated with a physical location, while allowing "ALL users" to connect to desktop computers only when you get close to those and not distance.
Looks like using the Kiosk mode to make the broker, authentication and connection of office and then disable the SINGLE sign-on and have instead users connect manually inside the VM, adapt to your usecase?
Maybe you are looking for
-
HP Sleekbook 15-b004tu: Windows 10 work
I have Windows 8 running by default HP Pavilion Sleekbook 15-b004tu How to check Windows 10 working or not on this laptop? and also all the drivers are available or not? ...
-
Browser of network (over ip addresses)
Does anyone know of a network browser Android who don't use ip addresses but can actually determine and work with host names. For most people, their networks have a DHCP server so the IP addresses are assigned dynamically, an ip address is not only o
-
Can I do a differential restore from Time Machine?
I have a user who has a file structure that lists many companies, each company has its own folder, and inside each folder there is a file called "Notes.docx. This means that each company has a generic file called notes: Companies folder File of the c
-
I ran the eseutil /d command, and after an hour and a half, I got the error above. The Exchange DB does not backup because it fails with a consistency check. Any ideas on what it is and how to fix?
-
How can I configure Windows Home Server also act as a Minecraft Server?
WHS xfer files and can currently running, see the server and everything on my network but I am unable to create a homegroup, also I'm trying to set up a minecraft server and everything is running but I am unable to directly connect to the server from