Conflict driver VISA

Similar Questions

• Can I install Driver Visa and USB-GPIB on LabVIEW7?

  Can I install Driver-NI-VISA and USB-GPIB on LabVIEW7? Or I need to install LabVIEW8?

  Thank you

  Véronique.

  Veronica wrote:

  Can I install Driver-NI-VISA and USB-GPIB on LabVIEW7?

  Yes.

  Or I need to install LabVIEW8?

  Only if you want to program in LabVIEW.

• How to fix a conflict driver VIA? Via the Audio drivers and OHCI IEEE 1394 Host controller?

  Because this motherboard (ASUS P5Q SE2), uses VIA VT1708S 8 - channel High-Definition Audio CODEC.

  And my PCI Firewire card is also VIA - according to Device Manager. It is running Vista. If I connect my DV cam (which has a mini-port FW on it), then turn it on, the entrance FW in Device Manager says there is a problem. But if I disconnect the cam, then restart, the FW entrance goes back to normal. I've seen this prob before, where someone else had the same prob (but firewire was aboard).

  I tried updating the FW driver through the Device Manager, but there isn't a newer driver available. I know that the FW card is fine. It was in my mobo previously (P5Q SE/R), which uses the Realtek ALC 1200, 8 - channel high definition Audio CODE, without going through. So, any ideas on how to resolve this conflict?

  Looks like I found the prob / cause. ASUS drivers Via for the sound. The latest version from the ASUS site

  I uninstalled them so I use the audio drivers by default Vista. The sound and the FW work. I plugged the cam DV again, made windows sound and it connected right away. Must be something in the audio drivers causing the conflict (such as an address / IRQ entry or something in the inf file).

• Conflict driver HP 8550 with Synaptics Touchpad driver Toshiba Satellite running Vista

  Install a new driver HP 8550 created a conflict with Synaptics Touchpad driver Toshiba Satellite running Vista. Fortunately, I also have a Logitech USB mouse that works, but the system sees as the Synaptics pointing device... How do you get again my touchpad?

  Hello

  I suggest try to uninstall all the drivers connected the printer to the computer, download the latest drivers from the link below and install it:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=19736&prodTypeId=18972&prodSeriesId=25507&swLang=8&TaskID=135&swEnvOID=2093

  It will be useful.

• HP Pavilion b119wm-15 Sleekboo: conflict driver Audio HP Pavilion Sleekbook 15-b119wm

  At one point, the pilots became a problem with my laptop. I have two drivers in the Device Manager. One is AMD high definition Audio Device and the other is IDT high definition Audio CODEC. When the AMD driver is enabled, the sound on the laptop barely records. If I disable this driver then the sound is much stronger, but this configuration is no where close to what I used to hear of my altec lansing/dolby stereo speakers built-in. It's frustrating that I can't simply updated the site with the right drivers based on my particular build. If I let windows to make it... It does not simply offer what I used to have.

  Second, I need to use the features of 'stereo mix' so that I can record audio "what you hear". Who does more either.

  Hello:

  The audio device AMD is just for the HDMI port, controlled by the amd graphics card.

  The IDT HD audio device is for speakers of the laptop and use with a helmet.

  So select the IDT HD audio when you use the laptop speakers.

  Reinstall the sound driver of W8.1 support page for your laptop and restart the PC and see if it works on W10, since there is no W10 audio driver listed on the support page.

  This package contains the driver that allows Audio IDT high definition (HD) in the notebook models that are running a supported operating system.

  File name: sp59852.exe

• Conflict of ATI with Windows, leading to the display driver crashes

  I have a matter of course on my new system. At first, I thought it was the video/hardware related, but now I'm leaning towards whether a conflict with Windows. However, I have no way of tracking it.

  Question: my screen is going to die randomly when running intensive applications Aero, games, etc. Everything will work fine for a while (anywhere), but then the clicker from desire to screen and the display will be turned off. On the screen, I see a series of vertical bars of white with a color background. It does not seem to lock the computer, as I hear it still go sound background for once; the computer restarts finally if I leave alone long enough.

  This is all performed on a new install of Windows 7 x 64, Vista Business 64 upgrade. Temperatures on the map of all read as usual and there is no errors appear in the event viewer after that I reload. Apart from the critical error "unexpected stop.

  When this first started happening, I contacted XFX Support for the video card. They had me uninstall the ATI drivers, run driver Sweeper and reinstall drivers. This seemed to solve the problem until Tuesday, when Windows Update installed KB977074 - a completely independent update of video - and then errors started happening again.

  After an adjustment with the restoration of the system, I tried to format the drive and start again. After getting Windows 7 x 64, I started to install programs one by one, checking after each installation to see if I could create the error again. Everything was going well until I reached a program that Basic Visual C++ 2005 Redistributable Package (x 86) installed. Once the error began to occur after that, I uninstalled programs and did a system restore before installing the package.

  The computer had already installed the C++ 2008 (x 64) package, and has worked once the 2005 32-bit package has been deleted. However, most of the programs that I want to use, and most of the GAMES for that matter, require the package of 2005 must be installed. So I re-installed and removed the 2008 package. thinking that it was a conflict between the two (/ straws), but it did nothing. Returned errors and I got a while back to square one, hiding on the last stable the system restore point.

  I don't know if I'm still on a conflict driver, hardware problems, or if the C++ packages are some how messing my system. I don't put much faith in the second, because I do not think that the first scan with driver Sweeper would have so much success, only to be later taken by a totally independent Windows Update file.

  So, to save my sanity. I've been looking through past posts and didn't find any error similar to mine, so I'm pretty sure this isn't another repost. However, if I managed to miss something, please point me to the right post.

  I have a my dxdiag output upward on pastebin; http://pastebin.com/f7e9f05c7  It was a little to long to post here.

  Hey David,

  Please check the safe mode and see how it goes.
  To start in safe mode, see:

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Also, try a lower resolution or check taken resolution supported by the video card.

  Reference:

  Change your screen resolution
  http://Windows.Microsoft.com/en-us/Windows7/change-your-screen-resolution

  In addition, I recommend that you try another monitor to check the issue and also check if the problem persists when you connect the monitor to another PC.
   
  In addition, please check the system requirements for Microsoft Visual C++ 2005 Redistributable Package (x 86): Windows 2000 Service Pack 3; Windows 98; Windows 98 Second edition; Windows ME; Windows Server 2003; Windows XP Service Pack 2.

  For further assistance with installation: Microsoft Visual C++ 2008, see:
   
  MSDN: Visual C++ General
  http://social.msdn.Microsoft.com/forums/en/vcgeneral/threads

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• GPIB-USB-HS shows no MAX after that I used the wizard NI VISA DRIVER

  I accessed GPIB USB HS in the MAX software. As I was not able to communicate NF RLC remotely, so I tried Wizard DRIVER VISA OR according to tutorial Assistant pilot NI VISA , however, thnings went wrong and I am not able to see same GPIB to the MAX software now. What should I do now?

  The first picture below shows the GPIB USB HS as shown in the software MAX and the other image shows no GPIB USB HS.

  

  

  Yet once I installed driver USB GPIB link below:

  http://www.NI.com/download/NI-488.2-15.0/5427/en/

  Its working fine now.

  Thank you.

• Session of visa driver looping issue

  Hello

  This is the first time I ever install a loop with a session driver visa in it. I'm trying to recover a table of data flow. The indices of the table correspond to physical locations (x, y) on this point that I measure the flow. This is why I need the data to be read as a 5 x 7 of the stream array. The matrix 5 x 7 is collected 3 times (at 3 different heights z). However, I can't understand why I make three 6 x 7 matrices instead of a 5 x 7. I can't tell if it's my registry setup shift, where my visa session is implemented, etc. I just can't understand it.

  Could someone looking at my code attached (it's quite simple, just 3 nested for loops with the session of visa inside, and that data are sent on to 3 matrices, which is then stripped more which can be ignored)

  Thank you very much

  Chelsea

  First of all, I don't see a point in all the structures of the sequence.  What they do is create clutter.

  Secondly, why you add the second to the last results to results together?  Here comes your additional index.  Get rid of this shift register and table construction.

• I can't install VISA driver and driver USB GPIB on my PC with VISTA... help me...

  I have LabVIEW7 and VISTA, it's ok, but I can't install the driver VISA and USB GPIB driver on my pc... it is necessary to connect my pc with instruments? Or LabVIEW7 have this files? Thank you

  Véronique.

  LabVIEW 7 is not supported on Vista and the version of NI-VISA supplied with LabVIEW 7 is not supported. You can download the latest version of NI-VISA - I ALREADY GAVE the link for you.

• Assistant of the Driver NI-VISA is compatible with Win7?

  Hi all

  I was wondering if NI-VISA is compatible with Win7, because I want to use it to configure my device. Thank you.

  Here is the link for the latest driver VISA which includes support for Windows 7:

  NI-VISA 4.6.2

• VXIplug & play driver need VISA

  Dear all

  our need for screws to find "ke24xx.dll". I searched the internet and I got I need to install this driver: "Keithley 24xx VXIplug & play driver VISA." This diver is related to labview 7.1.

  can any body give me this driver?

  Thank you.

  Best regards.

  I found something

  Thank you

• HP Deskjet F4480 conflict printer driver

  Printer HP Deskjet F4480, Windows 7, driver conflict error

  When I could not print, I ran the HP diagnostic tool, who met a driver conflict.  I followed his instructions and uninstalled the current driver and reinstalled the latest driver, but I still cannot print.  I restarted the diagnostic tool again with the same result, met a driver conflict.  How can I get rid of the conflict driver for my printer?  Thank you.

  What you describe, it seems that the USB cable is connected to the computer until the installation software asked for the connection.  In this case the generic Windows drivers and the HP drivers will try to install and collide with another.  I would like to Uninstall the printer and software.  Then reinstall of a fresh software download and make you wait for the software to ask the USB connection.  Let me know what happens.

• Conflict of Driver HP Deskjet 1050a

  Printer HP Deskjet 1050a, Windows 7, driver conflict error

  I noticed that whenever I went to print, the elements would be appear in the print to see what is so would disappear and not print. When I could not print, I ran the HP diagnostic tool, who met a driver conflict.  I followed his instructions and uninstalled the current driver and reinstalled the latest driver. I tried via the cd and also download on the hp website, but I still cannot print.  I restarted the diagnostic tool again with the same result, met a driver conflict.  How can I get rid of the conflict driver for my printer?  Thank you.

  Try using a different printer driver. That should clear up the problem.

  How to assign other drivers to print in different Versions of Windows

• Pavilion Dv4000: Windows 7 wireless driver help!

  Guys, I really need your figureing helps it to...

  My friends machine needed some TLC... so I formatted and reinstalled the Windows 7 operating system.

  I went to the HP support for pilots page and there are only drivers XP Win.

  In "Device Manager", it shows the following drivers requiring.
  
  Mass storage controller
  Multimedia Audio Controller
  Network controller
  Video controller

  The problem...

  I simply can't the wireless to work for love nor money!

  I downloaded and installed (a) different drivers for the wireless device. When they have been installed successfully, I'm supposed to be able to see a network to connect to diffuse all SSID wireless & Pick-up. I could not make it work! It worked once then stopped working again after it restarts as if this isn't retatining the driver for the wireless card. its really weird!

  

  Performed troubleshooting.

  • Downloaded the drivers for the wireless card and run them in compatibility mode (Win XP SP3) & installed.
  • Rebooted the machine. and the Wi - fi icon beside the clock has a red x through it, as it that the device is not enabled.
  • verified that the wifi was enabled. (what it was)
  • check that the pilot has been allowed within 'Device Manager' (it's still) drivers Displaying the "Intel 2200BG.
  • but still the Wifi symbol in the taskbar shows Red Cross or disabled marker on it.
  • Tried to install other Wifi drivers for the device of Intel 2200BG from other sites, including Intel. Restart, charges the driver installation (after removing the previous version) still nothing! same thing!
  • Tried to use the Intel utility to find the update and install the Wireless driver. (again same result).

  It seems that Windows 7 accepts the driver Intel Pro / Wireless 2200BG, but somehow somewhere to turn off the device in Windows 7.  How does it can disable a device but see that the device is installed and works unless you are a doubtful driver?

  Somehow, I managed to make it work for a while and connected to my wireless router. not a problem, then once the machine has been rebooted im at square one again!

  thinking that might be something wrong with the registry systems or material etc... I then

  • Formatted the hard drive again for the 2nd time.
  • Re-installed the card WiFi on the laptop, checked the connections were seated correctly
  • re-installed the operating system Windows 7 again.
  • before applying any other drivers on the system I tried to reinstall the driver from the HP website (just to remove it may be a conflict driver with another thing. yet once always the same thing.
    
    I spent hours on it now... and im at the point where I'm ready to run my friends laptop out the window and get extremely violent with her! I never met this before all the time, I played with computers. so I need someone to point out where im going wrong here. It's seriously making me crazy!
    
    I have attached a picture of this post, I hope that's clear enough for you to see that bar Wi - Fi symbol and the pilot agreed to "Device Manager".
    
    If anyone knows what drivers I can use for the rest of the devices, Audio, video (especially video and Wifi) and mass storage device would be much appreciated. There is still plenty of life in the old courbine of a machine and will make my boyfriend a good turn.
  • Someone please enlighten us on that until I lose the will to live!
  • Thanks in advance.
    
    Street

  You are the very welcome.

  I see that the multimedia audio controller device has been installed and that means you should have sound there.

  I already give you the driver for the mass storage controller (this is the card reader).

  Yes this is useful.

  The graphics in this model is not quite able to market Vista or W7.  Quite capable, I mean he can't run Windows Aero.

  There is that one driver in the world that has any chance of working for the graphics, it's this one... After installing this driver, you will be able to change the screen resolution and graphics acceleration is enabled.

  You must install it manually.

  Download and run this driver.  You will probably get an error not supported operating system.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=447304 & swItemId = ob_47264_1 & swEnvOid = 2096

  Conclusion of any windows error.

  Go to Device Manager and click on the video controller requiring driver.

  Click the driver tab.  Click on set to update driver.  Select her browse my computer for driver software option and find the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp34749.

  Make sure that the include subfolders is selected, and the driver should install.

  Reboot and the graphics should work just fine, but not Aero.

• Changes in VISA interrupt handling?

  Hi all

  I'm grabbing at straws here, so I'm looking for a shoulder crying.

  I wrote a prog to USB with CVI acquisition a decade for a Board personalized. It worked well for a few years, then was extinguished. We try to use again, but it is not working properly.

  We do not have the original PC, so we use it with the latest BCI on Win7 or XP, with the latest driver VISA (regenerated .inf file).

  Communication with USB works fine... except the interrupt routine. Instead of receiving a break with 3 bytes of data (say 'ABC'), I get TWO interruptions, the 2nd first with 0 x 1, the one with "BC". There are different types of racks of interruption of different lengths, all have the same cut in two, with 1 as 0 x 1, the 2nd one with valid data.

  Anyone has an idea why there might be such a change in the functioning of my interrupt routine? VISA changed its treatment of interruptions in this time?

  Short of a solution on the side of PC, we are ready to reflashing the card, in the hope that we have the most recent version of the firmware!

  It may be useful, here is a dump of the USB VISA settings (I'm not familiar with most of them):

  VI_ATTR_RSRC_IMPL_VERSION: 0x500400
  VI_ATTR_RSRC_SPEC_VERSION: 0x500100
  VI_ATTR_RSRC_MANF_ID: 4086
  VI_ATTR_RSRC_MANF_NAME: National Instruments
  VI_ATTR_INTF_TYPE: 7
  VI_ATTR_INTF_NUM: 0
  VI_ATTR_INTF_PARENT_NUM error: L'attribut spécifié n'est pas défini ou supporté par la ressource référencée.
  VI_ATTR_INTF_INST_NAME: USB0
  VI_ATTR_MAX_QUEUE_LENGTH: 50
  VI_ATTR_RSRC_LOCK_STATE: 0
  VI_ATTR_RSRC_CLASS: RAW
  VI_ATTR_DMA_ALLOW_EN error: L'attribut spécifié n'est pas défini ou supporté par la ressource référencée.
  VI_ATTR_TMO_VALUE: 2000
  VI_ATTR_TRIG_ID error: L'attribut spécifié n'est pas défini ou supporté par la ressource référencée.
  VI_ATTR_IO_PROT: 1
  VI_ATTR_TERMCHAR: 10
  VI_ATTR_TERMCHAR_EN: 0
  VI_ATTR_SEND_END_EN error: L'attribut spécifié n'est pas défini ou supporté par la ressource référencée.
  VI_ATTR_SUPPRESS_END_EN: 0
  VI_ATTR_RD_BUF_OPER_MODE: 3
  VI_ATTR_WR_BUF_OPER_MODE: 2
  VI_ATTR_RD_BUF_SIZE: 4096
  VI_ATTR_WR_BUF_SIZE: 4096
  VI_ATTR_USB_SERIAL_NUM: 1240332
  VI_ATTR_USB_INTFC_NUM: 0
  VI_ATTR_USB_PROTOCOL: 0
  VI_ATTR_USB_MAX_INTR_SIZE: 64
  VI_ATTR_USB_CLASS: 0
  VI_ATTR_USB_SUBCLASS: 0
  VI_ATTR_USB_ALT_SETTING: 0
  VI_ATTR_USB_NUM_INTFCS: 1
  VI_ATTR_USB_NUM_PIPES: 2
  VI_ATTR_USB_CTRL_PIPE: 0
  VI_ATTR_USB_BULK_OUT_PIPE: 1
  VI_ATTR_USB_BULK_IN_PIPE: -1
  VI_ATTR_USB_INTR_IN_PIPE: 129
  VI_ATTR_USB_BULK_OUT_STATUS: 0
  VI_ATTR_USB_BULK_IN_STATUS error: La référence d'objet spécifiée n'est pas initialisée.
  VI_ATTR_USB_INTR_IN_STATUS: 1
  VI_ATTR_USB_END_IN: 5
  

  Well, after a long and hard look at the firmware code, it appears to be simply a difference of between the software and the firmware version... What a waste of time.