Connect my - rio to PC via network router
Hello
I wonder if I can connect my rio to the PC (without adding wireless network card to the computer) through my network router. In other words, if I connect my rio for the network wireless router and the PC is connected to the same network via ethernet, can I control my-rio (send/receive commands) through the internet?
Thank you.
In a typical sceanrio, LAN and WIFI are bridged and part of the same subnet. There is no functional difference, and there is no routing involved.
Once the routing is involved. that is, if two devices are on different subnets, there may be complications. First, he need to distiguish between plain old routing and NAT routing (as typically found in consumer devices).
For a classic routing (assuming that all intermediate routers have routing tables appropriate), the only question here is the firewall. The routers neeed to allow traffic and endpoints (your windows computer and the MyRIO) must allow connections from other subnets. Most often, they only allow local connections by default for security reasons.
For NAT routing, the LAN subnet is invisible to the public internet. The entire network has only (usually) a public IP address. The NAT router performs the tracking of a NAT table that remembers the local IP address of outging requests (for example if you surf the web) and therefore knows where the incoming responses sent from the internet, modify the headers of packets and pushing them to the side LAN. This only works for connections initiated from the local network ougting. If the connection is from the outside, all that is visible is the public IP address of the router. In order to run a service on a computer on the local network, the router needs to know about it. This is what port forwarding rules are everything. In general, you must manually configure the router, but some special applcations can also create automatic transfer rules (whether by the router via an ALG, or by the customer via UPNP).
In short, you need to deal with two problems:
- Make sure that the packages can find their way to the destination (routing, nat, etc.)
- Verify that packets are allowed to make this trip (firewall policies).
Can you ping the MyRIO? What is the IP address of the MyRIO?
Tags: NI Software
Similar Questions
-
My wireless via a router disconnects completely and it is difficult to connect again
My printer is connected to my computer via a router (D-link, DIR-655) en. When I try to use all the functions of my connection printer wireless disconnects tottaly and its very difficult to connect again. My computer can not find the network connection at all. After several time setting the router power on and off, the computer can find the network connection wireless and after that the printer works fine until the next time the printer again, same procedure repeated again.
Oh, I don't think you want to connect your printer to the router with a USB cable. There may be a link to troubelsome, you will only be able to print to it, analyzing him.
Connect the printer to your router with an Ethernet cable. After that go on each PC and delete all instances of the printer in Control Panel > printers (or devices & printers on Win 7).
Then, add the printer in this way:
1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing. Get his IP address for a network Test printed on the front of the printer.
2. click on > start > Control Panel > devices & Printers.
3. click on add a printer
4. Select local printer
5. Select create a new port and select Standard TCP/IP Port, and click Next.
6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
8. If prompted, use the driver that is currently installed.
9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
10. we may ask you to share the printer. Choose No.
11. the printing area of Test Page is displayed. Go ahead and print it out.
12. click on finish. -
BlackBerry smartphones can not connect to ISP via wireless router.
I have my cell service through T-Mobile and recently upgraded to a Bold 9700 with internet service. I can browse the internet via 3G network and an address of hot spot using Wi - Fi. What I can't do, is access to the internet via my router wireless at home. The router Netgear (WPN824 v3) works very well via the modem cable for laptops and smartphone Motorola click on my daughter. When I turn off the 3G network, I get a "cannot find server message".
I went through the technical support to the company of cable, Blackberry and Netgear without solution. The problem seems to be with the router, but I can't find a way to fix it. I'm about to buy another phone or router. If anyone has any ideas please help. Thank you
It works! I've accessed the configuration of the router. It would work without security. It would not work with WPA - PSK [TPIK], I activated the two WPA2-PSK [AES] AND WPA-PSK [TPIK] AND IT is CONNECTED. I don't KNOW WHY, BUT I SURE AM HAPPY. I guess the BB don't like TPIK
-
Connection to CVS GigE camera via a network switch
It is a fundamental and very simple question!
I intend to connect two GigE cameras to NI CVS-1458RT for an application of Imaging. When I tested the configuration in MAX, I realized that I can connect the cameras directly to the PoE ports, or alternatively, connect the cameras directly to the network switch and in both cases, connect the CVS to my network via its ethernet port. I was wondering if there is a benefit by connecting directly the VCA cameras, if I do not anticipate supply their Poe or if my switch has PoE Betacam.
Thank you
Usually, you always want your cameras on dedicated lines, or at least only sharing bandwidth with other devices. The mechanism of transport used by GigE Vision isn't really sharing good bandwidth with other devices. If you only share the bandwidth on a link given with other devices, you can throttle each take only a percentage of the total bandwidth. If you have devices without camera on the link, they don't usually have a mechanism to control the gap inter-frame limitation insofar as GigE vision made which would be necessary for properly sharing the bandwidth without remove the packages of bandwidth.
If you end up sharing one of the ports for the operation and configuration of the CVS on the network, you will be at the risk of losing image data packets whenever the rest of the traffic is sent. Although there are mechanisms in place to return data, these add latency and jitter to your purchase.
Eric
-
I have already scanned to the folder of network of digital repository on a printer HP 8500 wireless, connected to a wireless G home network. However, I recently bought a new superisolants wireless router and am no longer able to use the scan function. I now get an error message that says: unable to connect to \\Computer\Folder Make sure the remote computer is turned on. The printer on the wireless network and works very well except for scanning to the folder of the network of Direct deposit. Thank you.
I called HP tech support last night that had me add IP address of the printer to the McAfee Firewall as an approved connection. Digital archiving to the network folder scan function works now.
-
1 computer (PC1) running Vista, to date, AVG free, Spybot S & D the timer running
2 may have been infected with spyware by surfing - received message in the Explorer to search for the virus, think it was fake
3 then lost wireless internet in the two IE & Firefox
4 but had a Skype conference call minutes 40 OK - Bizarro
5 lit (PC2) laptop running Windows (light version) 7 - same problem with browsers
5A AVG on PC1 has been updated - ran a deep analysis, found 44 spywares & fixed them
5 b also ran registry cleaner
6 has managed to update Spybot, is all business, then working browsers, internet connection complete
7 can now connect 1 PC to internet with ethernet connection, he can see the wireless and home networking (local access only) so I guess the wireless work, but he can not see the internet on this subject.
8 update both Spybot and AVG on PC1 with wired ran the two found no additional infection
It's really strange, I do not understand how to see PC2 PC1 and PC2 connected wireless to wireless home, but PC1 is unable to connect to the internet without a network cable...
All pretty useless Windows diagnosticsHello
A message in the small window that says connected wireless does not mean that you really have a valid functional connection.
Linking the means of router you can enter the IP base of the router in an address bar in one go, being able to connect, see and configure the router menus (extended to the wireless router manual should explain how to do).
If it will not connect to your wireless router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.
Enable security wireless after you eat to make a functional connection.
----------------------------
The wireless card drivers much also install utility wireless of the seller.
To ensure that if there are utility wireless isn't running with the native Windows wireless utility provider (Service WLAN).
----------------
Firewall software can block traffic Local to the network that you are trying to use because it is not set to the network Zone Trust.
Make sure you firewall No. preventing / blocks wireless components to join the network.
Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.
If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .
party like Hello and NetMagic 3rd network managers can block local traffic too.
---------------------------
Stack TCP/IP (network IP number) of work should look like.
Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.
http://www.ezlan.NET/Win7/status-NIC.jpg
Description is the data of the card making.
The physical address is MAC of the card number.
The xx must be a number between 0 and 255 (all xx even number).
YY should be between 0 and 255
ZZ should be between 0 and 255 (zz all the same number.)
The date of the lease must be valid at the present time.
* Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.
* Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.
-
want to connect to hp JO 6800 via wifi to my laptop with a wifi router. is this possible?
Hello
Yes you can, you can configure it for your printer:
Please follow the instructions in the following book:
http://h10032.www1.HP.com/CTG/manual/c00256077.PDF
Good luck.
-
Cannot connect my Photosmart C4780 to my network wireless (home)
Hello
I searched this forum and tried to solve my problem, but none of the elaborate suggestions.
I have a Photosmart C4780 and am under OSX10.8
Recently, our internet provider changed our wireless router and our SSID. As a result, the printer that is connected to the original network and properly functioning has stopped working. I tried to connect the printer to the new network, but failed. He said now that the printer is connected to the hp network (something) and I can't change it for the new SSID.
Could you please tell me what to do? I have installed the software mentioned in the HP website, plugged the USB cable into the printer to try to set it up, but it says that the printer cannot find any existing network (although I'm next to the printer and connected to the intended network wireless)
Fact a little kind of hard-reset on the printer can be a good strategy? How can he do?
Thanks in advance
Pedro
PS: The printer works correctly when printing via USB
PS2: It is not an option to return the SSID of the router to the previous
Hi @pedroa
You say "I have installed the software mentioned in the HP website", but there is no software for the compatible with 10.8 c4780. Mountain V10.8 OS X Lion: installing and using the printer on a Mac with the Mountain Lion.
As you know, this printer has not a wizard wireless version in the front panel instead us would typically connect the USB cable from the printer to the computer and run the installation wizard.
Because you have 10.8 on Mac, and it there is no full feature software and drivers, you won't be the configuration wizard, to configure the printer. You may be wondering now, well how can I set up then? Good question, we will restore the default network printers and the printer will have its own IP address designed for whats called an Ad-Hoc connection (wireless router). We will put the computer on the network printer and then print a report to get the printers IP address. At this point, we can access the built-in web server (EWS) and run the wireless from there. Once the printer on the network with the router, we can put the computer on the network and vuala that the printer and the computer will be on your network.
To restore the default network settings - since you have done this before I guess you know how, but for others who can see the message, here are the steps
- Press the wireless button
- Select wireless settings
- Scroll and select default network. Press Yes to recognize
- The radio turns off (the blue LED turns off). You may need to press the wireless button to turn on wireless
Put the computer on the network printer (temporary)
1. click on the symbol of the airport on the upper left side of the screen Mac
2. choose the network looking compared to the printer (we could say a variant of the name of your printer or HP setup) - it may take a few minutes to make it appearPrint the wireless network test - wait a few minutes to make sure the computer have established an ad hoc connection, otherwise the report will not have an IP address
- Press the Scan button (it also the wireless menu button)
- Select wireless settings
- Testing wireless access, then select.
The wireless network Test prints, search and note the IP address.
Open a browser (Safari) and enter the IP address in the URL (address bar).
Click on the network, on the left tab, click on wireless or 802.11.
At this point, we are looking at fore 'start the wizard' should be on the right side.
As soon as we will have to set up the printer to your network, you can put your computer on your own network.
Now you can add the printer in system preferences and print
Please let me know if that fixes the problem, thanks.
-
login procedure
I am running winXP home on laptop wireless via a router and I continue to have an effect on the net, and a window saying I need to go through a certain procedure of connectivity in order to return on the net than what seems to come regularly and after that I went through the procedure, I'm back on the net could you please inform me how to eliminate this problem.Hi conorcloris,
· What is the exact error message?
· Did you do changes on the computer before the show?
Follow the steps in the article.
How to troubleshoot a network home in Windows XP
http://support.Microsoft.com/kb/308007
In Windows network connection issues
http://support.Microsoft.com/kb/313242/en-us
Troubleshooting Internet connection sharing in Windows XP
-
Cannot access ESXi server via network
Hello world!
We have a HP C7000 Encolosure with 4 BL460c Gen 8 blades in front size of it. Back size of the C7000, we have 2 SAN Switch, 2 switch HP BLc GbE2c layer 2/3 and 2 Onboard Administrator Module.
Everything is working fine with IP addresses like this:
OA active:
IP address: 172.16.0.253
STANBY OA:
IP address: 172.16.0.254
Server Blade BL460c Bay 1:
The IP address of the ILO: 172.16.0.10
Server Blade BL460c Bay 2:
The ILO IP address: 172.16.0.11
BL460c blade Bay 9:
The ILO IP address: 172.16.0.19
Server Blade BL460c Bay 10:
The ILO IP address: 172.16.0.20
We can ping pc that connected to the port of ILO on Onboard Administrator (OA) IP addresses above. (I can it call PC MANAGE?)
Continue, we access OA via Web https://172.16.0.253 use of , then Console integrated to control 4 Server blades. We have mounted image ESXi 5.1 U1 and successfully installed on 4 servers blade.
We manually config IP address on each ESXi Server (like this):
BL460c Server Blade on Bay 1 as server ESXi 1:
IP address: 10.0.0.11
BL460c Server Blade on Bay 2 as server ESXi 2:
IP address: 10.0.0.12
BL460c Server Blade on Bay 9 as a server ESXi 9:
IP address: 10.0.0.19
BL460c Server Blade on 10 Bay as a server ESXi 10:
IP address: 10.0.0.20
Now we can ping server to another server ESXi ESXi 1. I mean 4 Blade Server can ping together.
BUT:
-We can not ping servers to blade PC of manage (that PC connect to the port of ILO on OSTEOARTHRITIS. In this scene, MANAGE PCs has the IP 172.16.0.100/16)
-We unplug the network cable from the port of iLO, then connect it to the port number 24 on HP BLc GbE2c LY 2/3 switch, then address IP of the PC to MANAGE the 10.0.0.100/24 value. Always the same, can only access servers
Can someone explain to me how to access this server (ping, http, etc...). Do we have to config switch HP BLc GbE2c LY 2/3? We read many many guide on the HP website, but they have not mentioned about routing or switch to configure
Thanks in advance!
It's my mistake!
My servers have 2 connections FlexLOM. That a connection has been enabled for 'network management' in ESXi. I do not understand, then I activated 2 connections. That cause outside the network can not access them.
I just disabled a single connection and everything works perfectly.
I thank everyone!
-
Connect TM wireless to an existing network
I want to connect my TM 2 to my net existing as a wireless client. My main router is not an Appleproduct but must stay as it is. My plan is to use TM connect my Synologi NAS with cable in room separat so I can have my TM and SIN away from my main router. I do not understand how to do this. So please help
The needs of the time Capsule to connect to a modem or a modem/router to the assistance of a permanent, wired cables Ethernet... just like the printed Installation Guide illustrates.
The only exception to this basic configuration would be if you have another router Apple producing wireless network, in which case the time Capsule could "extend" this network wireless.
If you are ready to add an AirPort Express, it could be possible to configure the AirPort Express to pick up the signal from your router wireless and the 'join' the network in this way. Then, it would be possible to have the Express send an Ethernet signal to the time Capsule . A configuration that is unusual to say the least.
Note that I used the word "peut" here twice. There is no guarantee that this type of configuration would work well for you.
-
Unable to connect 2.4 Ghz on home network
Get a message that I can't connect to my network of 2.4 GHz, but I am able to connect to the network of 5 Ghz I have Verizon FiOS and I use their Quantum gateway router. Verizon configures the router to separate systems 2.4 and 5 GHz with different names. In recent days, I noticed that I can't connect to the network 2.4 GHz. I rebooted the router a few times. I applied the 10.11.6 updated so I think that this could be linked to the who. Why go to the slower network? My printers are connected to the 2.4 GHz network and for some reason, when I go to the 5 GHz network printers go offline (this not is is when Verizon pushed update firmware to separate networks). So to print I need to switch networks. Also noticed that access to some hardware Plug devices only when I'm on the same network as them. Lots of questions here but hoping someone can help get at least my mac to back on the network of 2,4 GHz. thanks in advance.
Tom
FWIW, I also have FiOS and I have been on 5 GHz since its release. I just tried 2.5 GHz and now I can't connect to it either. Might be time for a call to Verizon.
-
I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?
I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.
Now I want to be considered on the floor and use it to extend the wifi without ethernet cable
The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.
Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.
-
hardware device
my wireless network is displayed with a cross and will not let me connect saying settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again :(Hello
What operating system installed on the computer?
Note: Look for errors in the network card device manager.
Method 1: Follow the article mentioned below, if you are using Windows 7 operating system.
Using the troubleshooter from network in Windows 7
http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
Method 2:
He looks at the IP address and other parameters are not set correctly, I suggest you contact your Internet service provider or provider router wireless to help on this.
For more information, follow the below mentioned article:
Set up a wireless router:
http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router
Follow the below mentioned articles and see if they help you:
Set up a wireless network:
http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network
Wi - Fi and in Windows network connection issues:
Wireless network card: frequently asked questions:
http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions
-
How can I unlock my network router so that I can access my Kindle? I don't remember even enter a password.
Hello mikebradburn
Do you mean that you need the network key to connect your Kindle If Yes, then you need to get the key from the router. Regarding setting up the kindle to connect to the network, follow the procedures below.To remove security and unlock your router, you will need to contact the manufacture of the router.
Maybe you are looking for
-
How to send the details of an event calendar by e-mail?
I would like to send the details of a calendar event in lightning to a co-worker an e-mail in Thunderbird. I can convert the event, but everything that is sent is the title and none of the details such as dates or place.
-
Tecra M9 - no power orange light error code sequence
Hello I have a Tecra m9 laptop and when I try to turn it on, it blinks with a light orange in this sequence: 6 short flashes, short 1 long blink, 1 blink, a ditch, and then it repeats. Does anyone know what is the problem?Any advice would be greatly
-
T440s: Where can I find the product key for Win7
Where can I find the product key for Win7 on a T440s? There is no sticker on the bottom, or under the battery.
-
Update kb948465 caused the error 80070490 error code
KB948465 low load failed in sept 09, no down load came in the sence, checked several times and tried to get them, nothing. I finally found this site.
-
In XP, why can't see a hard drive in the list of workstation?
I have a hard drive that can be seen in the devices, but also computer management/disk management Manager. But the drive does not appear in the list of workstation hard drives. The spooky part is under run cmd, the drive appears and I can Dir list it