connect other computers to the internet through an ad hoc network of a connection__ broadband windows 7

Similar Questions

• our airport time capsule connects to computers and the internet, but does not record on the usefulness of the airport as being there - is it dying or is their a reset?

  Our computers connect via wifi to a capsule of time to the airport and to the internet, but can't find the time capsule, nor can its hard drive. Y at - it a reset, we can try or he dies. It's only a couple of months.

  Turn about your Airport Extreme for 15 seconds and then power back on. As soon as you see the green light, you should be able to see him for a minute or two in the Airport utility. In the affirmative, and see if you have Back to My Mac active. If so, disable it by removing all the e-mail addresses of the back section of my Mac. Then update your Airport Extreme. Work quickly.

  Many have started having this problem within the last week, probably because Apple changed something in its servers CCMM. A real difficulty would come from Apple, but it should work if you currently have active CCMM.

• WRT54G - cannot connect computer wired to the internet through a router

  I have the WRT54G and unable to connect to the internet when you are going through the router.  I feel that I've checked everywhere can, but still does not work.  I connected the way the instructions, the lights are on the case and all that.  I have cable internet and when I plug directly, there is no problem.  When I try to 'ping' to check the connection between my computer and the router, I get "Request Timed Out".  I tried to reset the router and goes in this direction, but I can't go beyond checking the internet connection through the router.  Any ideas what I'm missing?

  Thank you!

  You should not use the installation CD at all.  If you throw it away.

  See here for the installer of cable.

• ICS mobile broadband Internet and an ad hoc network

  I set up my modem ICS O2 broadband and using a wireless network to share the connection. I tried to connect my laptop to the internet through the network, but even if I am able to connect to the ad hoc network without penalty I was able to connect to the internet with him twice.

  I searched through the forums and nobody seemed to have this problem. Someone had this problem? According to me, what is the origin of the problem is that whenever I connect to the ad hoc network, it is the most often recorded as a new connection instead of use the same one that could pose difficulties.

  Hello

  Try this instead of the ICS, http://www.connectify.me/

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Why other computers cannot connect to the internet with my ad - hoc connection?

  Hi all! Here's my situation.
  My friends router is dead and we are in the smack dab Middle no where with no transport and we want the internet.
  We have only an Ethernet however.

  Here's my situation.
  I want to create an ad - hoc network and share the internet connection using ICS. The problem is, when I secure my ad hoc network with WEP or WPA cannot connect to the network. The network is visible on the computers of my friends (mac and PC) and they put the password nothing is done.

  But here's the kicker, when I don't put no security on the network, everything works fine.

  How do I create an ad hoc ICS with security network and have not really work?
  Thank you guys!

  Hello

  Thanks for posting. If I understand correctly, you experience the problem with the connection of computers using the Ad - hoc network. Correct me if I'm wrong!

  Before I continue, I would like to collect some personal information on the issue.

  1. what security software is installed on your computer?

  2. share your protected password put on or off?

  The sharing tab is not available if you have only a WLAN card.

  Method 1:

  Follow the link below and set the ad hoc network.

  Set up a computer-to-computer (ad hoc) network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  Set up a wireless network without router

  http://www.Microsoft.com/windowsxp/using/networking/setup/adhoc.mspx

  Method 2:

  After you follow the steps above to set up ICS on the host computer, make the following changes on other computers (but not on the host computer).

  (a) open Internet Options by clicking the Start button, clicking Control Panel, clicking network and Internet, and then clicking on Internet Options.

  (b) click on the connections tab, and then click never establish a connection.

  (c) click on LAN settings.

  (d) in the dialog box settings of the network Local (LAN), under automatic configuration, clear the check boxes automatically detect connection settings and use automatic configuration script .

  (e) under Proxy Server, clear the use a proxy server for your LAN check box, and then click on OK.

  If the password protection sharing is disabled, I suggest to turn on you or so try if this can help fix the problem.

  Method 3:

  Follow these steps and check if that helps.

  (a) click Start, type Control Panel in the search box, press ENTER.

  (b) click on network and sharing Center, click change advanced sharing settings in the left pane.

  (c) click on him to expand the network profile (type) that you want to turn sharing on or off for protected by Word.

  (d) select (dot), turn on password protected sharing.

  Visit these links for more idea on the Internet connection sharing between computers connected on an Ad - hoc network:

  Set up a shared Internet connection using ICS (Internet Connection Sharing)

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-shared-Internet-connection-using-ICS-Internet-connection-sharing

  Change the settings for ICS (Internet Connection Sharing) Internet

  http://Windows.Microsoft.com/en-us/Windows7/change-Internet-settings-for-ICS-Internet-connection-sharing

  More information on:

  Using ICS (Internet Connection Sharing)

  http://Windows.Microsoft.com/en-us/Windows7/using-ICS-Internet-connection-sharing

  Reply back with the results. I'd be happy to help you further.

• Client VPN prevents internet access from other computers on the network

  Hello.

  I run Client ver 4.6.03.0021 from an office on a network of 11 computers via a hub 16-port. Internet access is through an ICS gateway to the cable modem. Once I changed the modem cable to test a backup and then switched back to the original modem. After this, only computers that have the VPN Client (running or not) could access the internet. Computers that have no customer VPN can access only certain sites. Commonly viewed sites would say "site found. Waiting for answer", but the answer would never come and IE 6.1 cling. When I would try ping sites, it would fail. However, some sites such as Google.com would work.

  On one of the computers, on a whim of head, I installed the VPN Client but have not set up a connection. Now, this computer will connect to any website I want.

  Is there a fix easier to get access to other computers on the network without installing the VPN Client on each of them?

  Thank you

  H. Adams

  Hello

  Looks like you are running in MTU problem. The reason I say it is, automatically reduces the MTU value to 1300 VPN client during the installation for the whole system. That is to say all the client computer installed VPN that have MTU from 1300.

  Try to cut down the MTU of other systems that have no VPN client installed to 1300. If it's a Windows system, you can use Dr. TCP (free).

  Vikas

• How can I connect to the internet through the dial upward through the computer another internet connection?

  If you want to tell me that MS will not support Windows 2000, please do not post. The computer on which internet Wi - Fi Connection has Windows Vista Home Basic on it. The computer that has WiFi but I want to test its dial-up access windows 2000 top. It has WiFi with utility that is necessary. It includes 12 Opera browser. As a resort last, if it is not possible at all means, ultimately, let me know how to connect to the internet through another computer via the telephone line through Internet connection sharing or network connection. Any help will be greatly appreciated. Remember, this is on the internet. Not on whether or not Microsoft does not support Windows 2000. If you tell me how it is not supported, please do not post. Internet connection will be between the two modems and two computer on Windows 2000, it has a LT Win modem and the Vista Home Basic has a CX110 in generation something like this modem. I ask this question is because my land line will not dial a number. I would like to test a dial, and if you tell me how it's slow, I use DC Unlocker to a broadband speed, so it won't be slow. Any help will be greatly appreciated. Windows 2000 has an Ethernet port.

  Hello

  1. are you referring to Windows Server 2000 or Windows ME?

  If you are referring to Windows Server 2000, please help the professional community of COMPUTING in the TechNet forum below:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

  http://support.Microsoft.com/ph/1131

  If you use Windows ME, visit the below mentioned link.

  http://support.Microsoft.com/kb/234815

• Unable to connect to the internet through WRT110

  Hello

  I can't connect to the internet through my WRT110. I am connected directly but my modem at this point shaw. My DHCP settings will not retain an IP address. I'm going to status on the router (192.168.1.1) and find all information, IP address, subnet mask, Gateway etc. Defautlt are set to 0.0.0.0. I click on the intellectual property of release, then renew the ip and that everything remains as 0.0.0.0.

  I tried to set my router to static mode and entering the information in bold to ipconfig below, but which does not either. I also tried to reset the router back to factory default and tried everything on again, without success.

  What I'm doing wrong here?

  IPConfig:

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : vc.shawcable.net
  Link-local IPv6 Address...: fe80::c056:e161:d17f:3 b 09% 11
     IPv4 address...: 70.79.143.236
  ... Subnet mask: 255.255.252.0.
  ... Default gateway. : 70.79.140.1.

  Tunnel adapter ISATAP.VC.shawcable.NET:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : vc.shawcable.net

  Card tunnel Local Area Connection * 11:

  The connection-specific DNS suffix. :
  IPv6 address: 2001:0:4137:9e50:3 c 46:300 d: b9b0:7013
  Link-local IPv6 Address...: d fe80::3c46:300: b9b0:7013% 13
  ... Default gateway. :

  Card adapt 6TO4 tunnel:

  The connection-specific DNS suffix. : vc.shawcable.net
  IPv6 address: 2002:464f:8fec:464f:8fec
  ... Default gateway. : 2002:c058:6301:c058:6301

  Decreed a second IP address of my modem and I could contact my ISP. My router works now after power off.

• I can connect to the internet through my browser, but cannot connect to an application based on a cloud

  We operate Windows 7 Professional and that you can access the internet via Google Chrome normally.  However, our hotel based on a cloud, RoomKeyPMS, property management system does not connect to our main office desktop (wired LAN connection).  We are able to connect to another computer on desktop (wired LAN connection) and a laptop computer (wireless connection).  All three machines access the internet through the same network.

  Apparently, there is a setting in the office that prohibited RoomKeyPMS to connect to a machine.  Can someone point me in the right direction to solve this problem?

  Hi Glen,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums:

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

• What happens if I am connected to the internet through two different sources or more?

  What happens if I am connected to the internet through two different sources or more?

  You get Internet from two sources. What did you expect to happen?

  This is not double the speed of anything...

• Why can I see my other computers on the same LAN after typing netstat b in same cmd if I didn't make any connection?

  Why can I see my other computers on the same LAN after typing netstat b in same cmd if I didn't make any connection?  owner of 192.168.1.104:50768 result [svchost.exe] TCP - PC:5357 ESTABLISHED

  Hello

  Thanks for asking!

  This is because the network discovery is turned on.

  If you want, I suggest try tuning off the COAST of the discovery of the network and check if it helps.

  Enable or disable network discovery

  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discovery

  Reply back with the results. I'd be happy to help you further.

• I can't start a desktop connection remote with my file server, but I can't get to my domain controller. Other computers on the network can initiate together.

  Using server 2003 as DC and server 2003 as a FS. Problem computer running windows 7 upgraded to vista professional. I can open a desktop session with the domain controller remotely, but I can't launch with the fs. Other computers on the domain have no problem with a server opening. I have access to shared folders on the MSDS via LAN and can ping the fs. Also can not use MySQL on the fs with this computer. FS cannot launch the Office with the computer problem remotely but can with others.

  Hi Gary,.

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited in the TechNet Forums; We recommend that you post your question in the TechNet Forums to get help:

  http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• Cannot install applications through Microsoft store in Windows 8 Pro: using the internet through the proxy: detected 'No. Internet Connection' Error statement

  I study in a University, and we have access to the internet through the proxy. We just need to put in the proxy port: in the settings of internet explore and authentication additional etc. is not necessary to access the internet. Everything else is working well, including windows update and even browse apps in the store of Ms. But I'm unable to install any application. Help, please.

  In fact here in ITI, all our internet traffic is routed through a proxy (to stop the torrent, filter things etc.). To remove the proxy is not an option.

  I solved the problem by using the following commands as an administrator:
  netsh
  WinHTTP
  import proxy IE

• Trying to connect my laptop to the internet and I get the message "validation of identity and then it is not connect."

  I'm trying to connect my internet to my laptop but its does not work (it is a new connection). I tried it on my other laptop and password have crossed (the computer on which he worked on had vista). In addition, he worked with other computers in the House. I get a message of identity validation and then it is not connect?

  original title: internet connection failure

  Hello

  Do you mean that you try to connect the wireless access point? Try to install Service pack 3. Also what you can check:
  Click Start-> settings-> network-> right click on your adapter connection-> properties-wireless => select Wireless (tab)-> select your (name) wireless access point->, then select properties-> click on authentication-> uncheck the "802.1 x authentication for this network" click ok on all screens.

  Restart your computer and try to reconnect.

  I hope this helps.

• Cannot see other computers on the network

  Am on XP SP3.
  When I go to network connections,
  Right-click on local area network
  Click Properties under the general tab,
  Click on install and click Service
  .. all I see is a list for a McAfee driver but nothing for Microsoft. I removed my computer some time ago with McAfee & he must have created problems that I can't see other computers on the network. Is there a Microsoft driver, I need to install and which will help to solve the problem of not seeing other computers on the network.

  On the general tab of the properties of your network connection to the LAN card, you should see a box under the heading "this connection uses the following items."  Most Windows XP configurations for home use have 4 entries in this box: Client for Microsoft Networks, QoS Packet Scheduler, file sharing and printers for Microsoft Networks, and Internet (TCP/IP) Protocol.

  If you don't have these, you need to install, even if you really need not the Scheduler of QoS packages.

  You seem to have got almost to the right place, but be aware that when you click on the button 'Install' in the box, you are given 3 choices: customer, Service and Protocol.  The "Client for Microsoft networks" is obviously a "customer." 'Internet (TCP/IP) Protocol' is a 'Protocol' and the other two are "Services".

  What elements you have installed?