connect the PC to the dedicated access point

Similar Questions

• After running Thinkvantage System Update, unable to connect the wireless access point

  I've recently performed Thinkvantage System update for updating various programs/drivers on my T61p.  I've updated the V5.12 access connections.  In addition to this I was required to update driver V1.52 power management and functionality of the shortcut key for

  V2.10.0002 (two of them were the most recent available).

  After these updates, I can connect is no longer to any access point wireless that worked before this update.  I have tried to reinstall earlier versions of Access Connections, but still couldn't connect to wireless access points.

  ANY help would be appreciated.

  OK, problem solved.  I found that when I ran last weekend system update downloaded and installed an incorrect driver for my wireless hardware.  I installed the correct driver and now the connection to a wireless access point works.

  Certainly, I don't understand how/why not update system would be to download and install an incorrect driver.  VERY FRUSTRANT and TEDIOUS!

• Droid Turbo could not connect the Cisco access point

  Greetings.

  Since the upgrade to a droid turbo, I was unable to connect to the network without wire of my work. I work in the it Department, but my experience with Cisco technologies and wireless is limited, so I tried to understand why. My previous bike x worked fine. We have a network of all the access points managed by a controller Cisco 4402 running version 7.0.98 of the BONES. I was able to connect to another wireless network that I could meet outside of work, and I am able to connect to the network of my work if I connect it is unsecured guest SSID. Only connections to our 4 secure networks fail. The controller reports that my phone cannot all simply to authenticate. The controller is configured for WPA2 / AES using a key 284 on the particular network, that I am trying to connect. I entered this key manually both via copy and paste. As far as my phone goes, I only tried to withdraw and time networks like tent to start it in safe mode without success. I read on various forums android that maybe it's a problem related to Kit Kat and this kind of problem has appeared on other handsets from other manufacturers, but nothing definite.

  Any suggestions would be much appreciated.

  -Josh

  Let me direct you to two other discussions here on the Droid Turbo forum and the other from Cisco which may help.

  Unable to connect to company wifi

  https://forums.Motorola.com/posts/af633eb3e4

  DROID WiFi Turbo questions

  https://forums.Motorola.com/posts/06a2f3c5ca

  Connectivity issues with Cisco and Moto X (Gen 2) allowed RMC controllers (probably related)

  https://supportforums.Cisco.com/discussion/12331486/connectivity-issues-Cisco-controllers-and-PMF-enabled-Moto-x-Gen-2

  I hope this helps!

• How can I reset or fix my router wireless or (lost the ability to connect wirelessly to the internet) access point

  Wireless hub works, other computers are connected

  On a laptop, I lost the ability to connect wirelessly to the internet (message: limited connectivity)

  Recommended by the system solution: reset or repair your access point or wireless router

  How can I do?

  I think that what you aim for is "power cycle".

  To do this, simply unplug the router/access point power adapter. Wait a minute. Then reconnect it.

  Hope this helps

  Post back if necessary

  ___________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• WET11 V2 cannot be connected to the AP (access point) via WiFi

  I am facing following problem.

  Someone at - he advice me please how to solve these problems.

  Purpose:

  1. I want to use internet on TV Sony Bravia. (Bravia has no WiFI. "I have only LAN).

  Environment:

  1 access point (Router) - WiFi > WET11 V2 - LAN > TV (Sony Bravia).

  2. IP address 192.168.1.5 = WET11 (automatically not static)

  BOF WET11 V2 assigned IP address access point.
  I checked the access point access point IP attributed to WET11.

  3 TV IP address is automatically.

  But the IP address is unaffected for television.

  4 WET11 firmware version = V2.05 (Sep 16, 2003)

  Problem:

  1. IP address cannot be assigned for television.

  2 WET11 is not the answer for the command 'ping 192.168.1.5' WiFi access point.

  3. I did ping command when the LAN TV cable has been replaced by the wireless access point LAN cable.

  BR

  Mutt

  It is not advisable to use a 802. 11B wireless bridge on a device such as your streaming media TV. Connection will be very slow and is probably the reason why you have a hard time to connect to your wireless router that's more compatible with it. I suggest using a Wireless N bridge or a multimedia wireless on your TV adapter so that you can fully appreciate the media streaming.

• Windows 7 wireless emphasizes the connection to the wrong access point

  I use a model of wireless USB Netgear WN111 with Windows 7 64-bit adapter, connect to a D-Link wireless access point.

  Every time I have connect or wake the computer from sleep, he insists on connecting to the wrong access point - it connects to an unsecured Linksys device somewhere within the range.  I then manually connect to the correct access point - my D-Link.

  I went into the network sharing Center > manage the wireless networks and removed the network Linksys of rogue, but it always comes back.

  Any ideas or advice?

  Hello

  I don't know why he keeps picking up the 'rogue' network after that you deleted. My Windows 7 does not behave like that, and my research can reveal a way that I could do. Maybe someone else can tell you why he does. However, as a solution, you can try the following in manage wireless networks...

  1. do not remove the network of thugs, move it to the bottom of the list all the way down.

  2. open the rogue network properties and uncheck the box "connect automatically when this network is in range.

  3. open the properties of your network and check the box "connect automatically when this network is in range.

  4. you can even try to untick "connect to a more preferred network if available" both networks.

  Please mark this as useful or response if applicable.

  Tricky

• Windows 7 PCs are not connected to the closest access point

  Windows 7 PCs are not connected to the nearest access point.  Any ideas?

  For example:

  We have AP 1 and 2 of the AP for exaple.  They have the same SSID.  AP 2 is further with a bad signal.  AP 1 is closest with an excellent signal.  Why my laptop does not connect to the AP 1?

  You MUST use the same SSID.  I think that you misread my post.

  And Yes, a channel problem is that what I have proposed.  You can try to configure access points using the 3 discrete channels (1, 6 and 11) to minimize any overlapping units to the same channel coverage.
  At least this is the traditional way, we do it, although the automatic selection increases common and 11n 40 Mhz channels (if defined in this way) are also in.

• Ordered the wrong access point!

  I thought that I had ordered a 1130ag but looks like I ordered a 1131ag LWWAP.

  Please could someone tell me what the difference between a 1130 and 1131. I understand I can load the IOS on the light AP software using a tftp server, but I do not know which exit to load on this subject. 12.3JX, 12.3JA, 12.3JEA, 12.3JEB! can anyone help please? either by the way, I am in the United Kingdom, do not know if this affects image to install. Thank you.

  Hi Paul,.

  This happens all the time, so it shouldn't be a problem :) I'm guessing that you have received this AP - AIR - LAP1131AG - x - K9 LWAPP. When you really wanted this AP - AIR-AP1131G-x-K9 Cisco IOS software. Look at the comparison;

  http://www.Cisco.com/en/us/products/ps6087/products_data_sheet0900aecd801b901c.html

  That being said, you should be good to go with 12.3 (11) JA1.

  To access Cisco Aironet to Cisco IOS version 12.3 Points (11) JA1

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b11jar1n.html

  Cisco IOS version 12.3 (11) JA1 supports 32 MB independent platforms. 16 MB platforms and platforms supported by Cisco IOS version 12.3 (8) JA and earlier versions (350, 1100, 1130, 1200 and 1230 access points and access point/bridge 1300 series) are supported by Cisco IOS version 12.3 (8) JEA1.

  Do not install a "JX" (it is a software image support to upgrade and recovery Cisco Lightweight Access Point Protocol (LWAPP));

  These release notes describe features, improvements, and caveats for Cisco IOS release 12.3 (11) JX1.

  Note: This version must be loaded on points of access to the plant or by using the lightweight stand-alone mode upgrade tool. Your access point may become unusable if you install this software without using the upgrade tool.

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b311jx1.html

  Returning to standalone Access Point

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• 4402 wireless controller and the 1130AG access points

  I have a bunch of 1130AG (35) and 1231 points of access. I just bought a controller 4402 so I could handle these much easier access points. I currently have the offline access points, so I could control. With the wireless in the mix controller, that I have to fix these to light mode or can I leave them offline.

  We know not the operating instructions so I can leave them in stand-alone mode. Most of them is in the rafters in our warehuse, and I didn't have to pull of these if I have to. If I can use them offline, how can I do that?

  Thanks much for any info!

  Dave

  Hi Dave,.

  A WLC manages autonomous APs.
  So if you want to centralize the management of your APs through the WLC, you will need to convert it to light and enter them on the WLC.

  To convert the lightweight access points, you can choose between several options:

  1. thanks to a specific upgrade tool that you could install on a PC:
  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html

  2. [the most evolutionary] by WCS, with a model of migration that could apply to several APs:
  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0apcfg.html#wp1054876

  3. [not in any book] by the following steps:
  3 (a) download the CEC lwapp recovery image and store it on a TFTP server.
  3 (b) Telnet to the stand-alone PA and issuing the following command:
  Archive Download-sw / overwrite/reload tftp: / // [lwapp recovery image file path]

  As a general recommendation, before to convert the lightweight access points, you can be sure that the wired infrastructure behind is ready to direct them to the WLC for recording.
  It's suggestions explained in the link on the above option #1.

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Tecra 9100 - unable to connect to the WLan access point

  Hello

  I have a Tecra T9100 with miniPCI WLan. I reinstalled XP Pro and all the drivers (downloaded from the Toshiba site) and I've always had a problem with Wifi:

  I can see all access point (in the windows control panel), but when I click on connect, I received a message that the access point is no more...
  He didn't ask me for the security settings?

  does anyone have an idea?

  Much thanks

  Leclere

  Hello

  To my knowledge the Tecra 9100 was equipped with the wireless LAN standard: 802. 11B mini card PCI ORiNOCO.

  You need to check if the WiFi signal is strong enough for a transmission correctly
  I think that the signal of WLan access points is not strong enough because of the distance.

• Satellite M70: I can't connect to the WLan access point

  I have several wireless laptops, all work fine - except my M70.
  I use Intel Proset, and he sees the access point, but says "unable to connect" when I try.
  The signal is high (2 meters distance).

  I tried with WEP, WPA and without security. I am absolutely convinced that I entered the right keys.
  The access point is a Belkin Pre - N-, but I tried with a point of access 3Com, with the same problem - my Ipaq, my other PC, and all guests can connect,- but not my Toshiba!
  The wireless card is the standard Intel, with the latest driver from October 2006 intalled.

  Getting desperate...

  Hello

  If you get a signal strong, so I guess that the laptop is already connected to the access point. Or am I wrong?
  On my laptop, the computer WLan small icon appears only if I connected to the Wlan and then I can see the State of the signal.

  However, you suggested to use the Intel Proset utility to configure the WiFi network but on the clean Windows configuration. Have you tested it?

  This question seems very strange to me.
  Sometimes it of not possible to connect the WiFi network because of poor compatibility between the router and wireless network card.
  My router supports Wlan AB mode and my second card for computer laptop support BG.
  That's why I m not able to connect to the Wlan. Maybe it s also your case.

  On my router, I can also put the MAC address filtering. You should check this option on your router.
  But generally it is not easy to say why it happens. You know you should check every single option and if it s not possible so I guess that it s a compatibility issue.

• How to force the client to connect to the specific access point?

  I have a client that connects to an Access Point to the upper floor.  The connection is "Very low" and pings are restless.  Is there a way to force the client to connect to the point of access on its own soil in the hallway.

  Access Points using 1131AG; WLC2106

  PSK + WPA2

  Thank you

  There is not a way to force the client to use a specific side access point controller of things.  According to the specifications, the client decides when and where to associate.  You can try to disable some of the rates below data or lower power tx of the AP to reduce the coverage of each access point cell.  By doing this, the client cannot see the other as favourable AP.

• Set up the wireless access point, but the wireless devices are unable to get ip address

  Hi, I wanted to put my D7000 as router AP. My main router is Sagemcom F@st 3864 by Optus ISP (Australia).

  First of all, I put the D7000 in Bridge mode I did these steps:

  1. replace the IP LAN 192.168.0.100

  2 disable DHCP

  3. connect the LAN port to the main router Lan port

  Internet connection wired and wireless on the same device but other wireless devices has failed

  To remedy this, I made another choice, allowing point-to-point wireless access in the advanced settings of the D7000. I followed the instructions from this link

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24104/~/how-do-i-change-my-Nighthawk-router-to-AP-mode...

  I put dynamiccaly = wireless internet cable success but peripheral does not have an ip address

  No idea how to fix wireless? I'm not very experienced

  Thank you!

  I just fixed it just now. For AP mode, connect the LAN port of the main router to the WAN port on the D7000 (not LAN to LAN). I wish I thought to it much sooner.

• Subnet routed on the main gateway of the WiFi Access Point

  Hello people.

  I have the wireless router WAG200G. It sports a RJ-11 input and a four port RJ-45, while it is compatible 802.11 g.

  I need to use it as an Access Point, WiFi via DHCP clients accommodation in its own range (I fear not the 192.168.1.x default range). However, I need to give this subnet, access the internet via my main network which has another Beach, say 10.0.0.x, where the entry door is 10.0.0.2

  I tried the subnet routing WiFi to my front door, but apparently I'm missing something I ever managed :-)

  For those wishing to help could you please tell me through this page http://ui.linksys.com/files/WAG200G/1.00.09/Setup_routing.htm ?

  FYI, I got the Linksys in my network off main application everywhere (Linksys & PCs) static IP, nat and affecting encapsulation Bridged Mode only. That's how it worked, but for security reasons, I need to isolate this subnet WiFi.

  Any kind of help would be appreciated.

  If you used the WAG as point of access only with standard Linksys firmware, then you cannot use the DHCP server. The WAG will always assign its own IP address as the gateway via the DHCP server. The only option would be to use the DHCP relay function or set another DHCP server.

  As long as the WAG is connected through a LAN port to your existing network you connected side full LAN of the WAG in your network. You don't want to run any DHCP server on the WAG. Your main router provide DHCP service. If your wireless devices have trouble getting an IP address from your main router, which should be the first thing to solve...

• [Wireless-Vista] Disable the automatic access point.

  Right then, I had this problem when you play any kind of online game, what microsoft calls a 'feature', when I play a game online, I get a 5seconds or until disconnecting lag spikes every 1-5 minutes, making it impossible to play counter-strike, Call of Duty Modern Warfare 2, Battlefield 2 and all these sorts of FPS games. I read on this vista of "paintings" Wi - Fi point automatic scan has, so I tried with impatience to deactivate, without success, I even once turned off automatic TCP/IP that crashed my computer, so now I'm wondering, how in the world am I supposed to play a game with spikes of major shift due to a malfunction of the so-called?
  If there is a way to turn it off, remove, or simply work around, tell me. I don't care if it is not allowed, because I got it with feautures of microsoft...

  sckizman,
  Have you ever been able to play games online with this computer?
  What version of Vista and what service pack you have?
  You are able to surf on the net normally or you we lag with almost anything on the internet?
  If you have not yet done so, perform a clean boot , and then test your access.  Also make sure that your system BIOS and chipset drivers are up to date.

  Here are instructions on disabling automatic switching between wireless access points:

  Prevent your computer from switching between wireless access points

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.