Connect to the HP ePrint Center

Similar Questions

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• "Could not connect to the server Game Center"

  OK, so here's the deal:

  Im trying to connect to Game Center on my old phone to synchronize the progress of game. When I try to log in, it tells me that it could not connect to the server. I tried just about everything I could find on the Internet without success (discount and hard reboot reset settings do not work, and the servers are not enabled). Could someone tell me please how to fix this?

  iPhone 3GS, iOS 6.1.6

  Honestly, I don't want to hear that if you encounter the same problem, I just want to know how to solve this problem. Thanks in advance!

  Nevermind, it seems to have fixed itself.

• Windows Media Center extender on my XBOX works initially, but not after reboot of my XBOX. Error: Failed to connect to the Xbox 360 could not connect to the windows Media Center computer.

  It's VERY odd and very annoying!

  I set up my laptop next to my Xbox 360 with an Ethernet cable directly connecting the laptop to the XBOX, and the laptop is on our wireless network. The XBOX has access to the internet (shared through the laptop), and when I test the PC connection and the connection XBOX Live sound fine to all.

  So I'll try to set up Windows Media Center, it works great! I "Add Extender", put the code to 8 digits. It passes through the installation, all works, no problems and WMC opens on the XBOX, I can go into my library, watch movies etc... works great!

  However! As soon as I turn my XBOX off and back on, it will fail to connect to the WMC.

  He says his 'find Windows Media Center PC' which seems to work fine, it goes to the ' Windows Media Center loading screen "contact...". ", and after about 10 seconds, I get an error"failed to connect the Xbox 360 could not connect to windows Media Center PC. Make sure that the PC is turned on and connected to the network.

  I tried to configure the Extender repeatedly, whenever it works fine until I restart the XBOX... :/ - and its strange cause I still the internet connection (shared through the laptop) after turning on the XBOX, its really JUST Media Center which is screwing around.

  She continues to keep trying to connect then repeatedly fails.

  If I wanted to, I could re-configuration the WMC Extender EVERY TIME turn off the Xbox, which works the first time without fault, but that's all just stupid.

  I can't really understand what is happening here... any help would be appreciated.

  Hello

  Refer the article that could help you solve this problem.
  http://support.Microsoft.com/kb/932163

• Error message when you try to connect to the HP ePrint ' ajax submit failed: Error = 403, forbidden.

  HP Photosmart 7525

  Windows 7

  Ajax submit failed: Error = 403 Forbidden

  Installed new printer: Photosmart 7525

  I am trying to configure my ePrint account and add my printer and it wont let me sign in or create a new account.

  Thanks for your help!

  Deb

  You can also restart the computer. After he stops down to leave it for at least a minute and then reattempt access the site once computer is back on and running. I would also check to make sure that Java is up to date and that Adobe Flash is up to date.

• HP Photosmart 6525: eprint center

  I tried several times to log in my Center ePrinter, but he recalled that my login ID is an incorrect email address.  Then when I try to register a new name to logon user with this email address, it was reported as error that this username already exists.

  I don't know that this email address log you name is correct, because I've used it several times before and it's one I had.

  Please advise urgently how to fix it.

  Hey @norseman1,

  Welcome to the Forum from HP Support.

  I understand that you are unable to connect to the HP ePrint Center.  I want to help you with this.

  I don't see this particular error with password resets from time to time.  I have a workaround that can clear up this place for you:

  • Click here.  This will bring you to <www.snapfish.com >.  As the Snapfish site is linked directly with ePrint Center and HP connected, you can try to reset your password as follows - click the connection icon and then "forgot your password":

  

  • Enter the e-mail address that you use to connect to the ePrint Center and click on submit.
  • You should receive a message of automatic reset of password by email - the reset as expected before and then try to use this new password to Snapfish to connect downtown ePrint.
  • If this does not solve your problem of access ePrint Center, please call our Cloud Services to 855-785-2777. If you do not live in the United States / Canada region, please click the link below to get help from your region number.
    
    http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps.  If my suggestion worked in your favor, feel free to give me a virtual h.o.t. by clicking on the 'Thumbs Up' icon below.

  Have a great day!

• Cannot connect to the HPConnected and ePrinting having the delay of 1 hour

  Hello

  Once connected to the ePrint I asked me to update for HP connected (I lived the delays of long hours of ePrint). The first time that it worked very well, but later I was not able to connect because the site causes an infinite loop: tries to go to en / us-> will detectlocale-> will fi / fi-> goes to en / us-> detectlocale-> fi / fi-> en / we...

  Can you please do something?

  Second thing is that you can not really rely on this service. I've been using ePrinting for 2 years now and whenever I need to print something more than a single document there are long delays and problems for connection etc. Last time this happened 2 weeks ago now today still.

  BR

  Did not help either. The same loop after login. I tried to connect to Snapfish - I had no problem.

  BUT, I tried to connect to the old ePrint and from there when I get the message that I've already updated, I can click the link to the HPConnected that seems to work. It worked not earlier, but now after this, I can also connect to new straigth to the HPConnected!

• OfficeJet 6100 x (H611a) will not be re - connect to the eprint Server

  My printer HP Officejet 6100 (H611a) has been connected to the server eprint for over a year.  A few days ago when I tried to print from my tablet, he told me that I was no longer connected to the server.

  When I went to the page of the built-in web server, it showed that I had lost the connection and was an icon that says 'fix it '.  I tried the reconnection to the server by clicking on this icon for several days without success.  He would say "unable to connect to the server.

  Finally, I tried to cancel the registration of the printer and tried to start over.  Now whenever I try to save the printer it says "unable to connect to the server.

  I tried this for about two weeks, without success.  Any help would be greatly appricated.

  Hi scthom,

  Welcome to the Forums of HP's Support.  I understand that you get a connection error message when you try to connect to the web services of HP to use ePrint.

  My feeling is that there was an update to your router or modem firmware and this update is causing the printer to communicate with HP.  Please define Manual of the printer an IP address manually and DNS servers.  I've included a link to another post with measures, including screenshots, of how to do it.  Don't worry that the screenshots are for an Officejet 8600 the steps are the same.

  Please let me know how it goes.

• HP 8500 printer and connection to the eprint Server

  Given to nine printer: HP Officejet Pro 8500 A910 n Premium (changes the status back to renovated 17/02/2011)

  ISP: ATT DSL

  Modem/router: 2wire new from Best Buy. It is white with ATT logo on it. Using the latest firmware.

  Network: ethernet

  The printer downloaded and installed an updated after initialization. If it is connected to the internet.

  Then tried to register the server says that it cannot connect to the server of the eprint and eprint.

  The functions of the printer normally in all directions except that it will not fit on eprint server.

  Many calls and hours with the reboot, reset HP support and everything else under the Sun did nothing.

  I tried to place the IP addresses and DSN by any suggestions on these forums and nothing works.

  Could there be a problem with the HP Sever? Does it really exist? Are there problems of compatibility with 2wire router.

  ATT session remotely on my computer and could find nothing they could do. They were able to draw a page of remote test.

  Any suggestion or help would be greatly appreciated. Thank you.

  NEW INFORMATION (11/02/2011):

  I noticed today just by looking at the integrated Web server, printer SSID is not the same as the router, but it is grayed out. Is it important for ethernet? If so how can I change? I don't think it's important for the ethernet.

  NEW INFORMATION (12/02/2011):

  The 2wire support team gave me the procedure to open completely all the in and out traffice to the printer. They said that if it does not, then the problem is with the eprint server. I'll try this Monday, but I expect a communication problem between the printer and the eprint server that does anything at my place or my ISP. Is it possible to check this printer is trying to connect to the server? Where is he? Is it operational? If this is not the case, is it rerouted properly to a working server? The printer must attempt to access an IP or DNS address to establish communication magnified.

  NEW INFORMATION (14/02/2011):

  According to the 2wire support team I opened all the ports and enabled all services then turned the printer market. It did not work. The printer does not connect to the HP eprint server. So the problem is with the HP eprint server. This printer is programmed to search for a server to connect to somewhere. Where is he? Is it operational? Why will not allow a connection? HP, the ball is in your court. What can we do?

  I have ATT DSL at work and at home Charter cable service. The problem is the same for the locations and ISPS. Y does it have that someone out there has connected to ATT DSL or cable of the Charter? If so, what are your settings?

  NEW COMMENT (15/02/2011)

  Can someone at HP tell me why the printer connects to the server HP and download the firmware update, but does not connect to the HP Server to register for eprint? All this seems to be on the side of HP. When do we get a fix?

  NEW COMMENT (16/02/2011)

  The model number is empty in the Engineering menu and page printer card. If there is a problem can be added with an update of the firmware? What I need to get money for it and buy one set entirely in a local store? Virgin model number is maybe to throw all other incongruous information that is sent to the server. The server can be updated to accept Virgin model numbers?

  THE PROBLEM - SOLUTION PENDING POSSIBLE SOURCES (16/02/2011)

  I JUST LOOKED AT THE BACK OF MY PRINTER. IT HAS A STICKER ON IT RECONDITIONED.

  It seems that the number of missing on the remanufacturered units model is the reason why it does not connect to the eprint server. Print the diagnostic printer page and see if the model number is empty.

  HP is working on a fix.

  SOLUTION-(22/02/2011)

  I UPGRADED MY ORDER WITH RENOVATED WITH NEW REPLACEMENT. THE REPLACEMENT AGAIN CONNECTED THE FIRST TIME TO THE SERVER EMPRINT - NO PROBLEM. I HAD TO PAY FOR A NEW AND THEY WILL CREDIT MY CARD WHEN THEY REACH THE RENOVATED A RETURN.

  LESSON LEARNED - IF YOU HAVE THE PRINTER WITH THE VIRGIN MODEL NUMBER YOU CAN NOT CONNECT TO EPRINT, NO MATTER WHAT YOU DO!

  Thanks if anyone can help.

  SOLUTION-(22/02/2011)

  I UPGRADED MY ORDER WITH RENOVATED WITH NEW REPLACEMENT. THE NEW REPLACEMENT CONNECTED FIRST TO THE SERVER EPRINT - NO PROBLEM. I HAD TO PAY FOR A NEW AND THEY WILL CREDIT MY CARD WHEN THEY REACH THE RENOVATED A RETURN.

  LESSON LEARNED - IF YOU HAVE THE PRINTER WITH THE VIRGIN MODEL NUMBER YOU WILL NOT BE ABLE TO CONNECT TO EPRINT, REGARDLESS OF WHAT YOU DO!

• OfficeJet Pro 8610: How to connect to the internet.

  I have my printer connected with a USB cable, but the info. says I can't connect to the HP eprint site. Is there a way to do this? What info. I can find says I can't divide just the cable my computer the printer must have its own IP address. will be a book of crossover cable or a possible someother wiring installation?

  Respectfully,.

  Pat Hagar

  Hello

  I don't know what is. Looks like you need to a router or switch that allows to connect several devices. My suggestion: buy a wireless router with LAN a few ports, you can connect modem and use it for wired connections and wireless

  In the image below, you can se the router (R) (M) modem. You can connect your computer to the router and you can connect your printer using LAN cable or wireless. You can connect other computers, Tablet (s) or smartphone (s) to the same wireless router.

  

  To help in this way, your printer can connect to Internet.

  Kind regards.

• LJ pro M177fw: eprint center connection problem

  Hello

  today I am trying to add my new printer to my eprint account, but I do not remember my pwd, so I want to co reset the password.

  By e-mail, I received a link

  http://h30495.www3.HP.com/reset_password/xxxxxxxxxxxxxxx

  but it didn't work, the Web server show this error:

  SERVER ERROR

  Oops! Only, something was wrong with our server.

  Try refreshing the page.

  I tried different browser and pc, but I can not reset my pwd.

  Is there a solution to this problem?

  Is the server down for ever?

  Thank you and best regards.

  Roberto

  Hey @Roberto_ITALY,

  Thanks for posting in the Forum from HP Support.

  I understand that you are unable to claim your HP Color LaserJet Pro MFP M177fw in your account ePrint Center due to a connection problem.  I would like to help.

  I don't see this particular error with password resets from time to time.  I have a workaround that can clear up this place for you:

  • Click here.  This will bring you to <www.snapfish.com >.  As the Snapfish site is linked directly with ePrint Center and HP connected, you can try to reset your password as follows - click the connection icon and then "forgot your password":

  

  • Enter the e-mail address that you use to connect to the ePrint Center and click on submit.
  • You should receive a message of automatic reset of password by email - the reset as expected before and then try to use this new password to Snapfish to connect downtown ePrint.
  • If this does not solve your problem of access ePrint Center, please call our Cloud Services to 855-785-2777. If you do not live in the United States / Canada region, please click the link below to get help from your region number.
    
    http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps.  If my suggestion worked in your favor, feel free to give me a virtual h.o.t. by clicking on the 'Thumbs Up' icon below.

  Have a great day!

• DeskJet 3052 j611 series a - unable to connect to the ePrint Server

  I am connected to my network domestic ePrint not connected to the internet

  OK, problem solved! In Control Panel-> network and sharing Center control, I had my WiFi network, the 'Public' value that limits certain features. I changed that "Private" that allows a wider and ALTO network discovery!, now works for web services.

• Can you see the ink levels Eprint Center for the OfficeJet 7500 a/E910

  You can monitor the eprint Center ink levels for the OfficeJet 7500 a/E910?

  Hello Deborah,

  To answer your question, you are not able to check the ink of ePrint Center levels. The only thing you can do in ePrint Center is to monitor the status of your print jobs you send via ePrint and monitor the connection status of your printer for the recent servers ePrint.

• Windows XP Media Center 2005 cannot connect to the Internet

  Dear all,

  I'm having a problem with Windows XP Media Center 2005. The problem is that when I connect the cable from the modem to the laptop, I only send packets without receiving. The IP address I get is also 169.254.207.207, which is not a valid IP address to connect to the internet, and so I guess that something is blocking the laptop to get the IP address. Another thing I noticed is that when I turned off the modem and restart it, I have connectivity maybe 5 seconds and then return to no connectivity.

  You guys can tell me what is the problem, and if I have to download something but in addition to the internet so that I can get my laptop to work. That said, I can connect to wireless with no problems.

  Thanks for your help and your time

  Martyna

  Hello

  Sorry for the question but what modem did you mean?
  A simple analog modem or DSL (broadband) modem that supports support a LAN connection.
  If you mean the second then I would check the TCP/IP settings in the properties of LAN card. The settings should be set to automatic

  You should also check that you firewall settings.

• HP8600 does not connect to the ePrint Server

  HP8600 does not connect to the ePrint server at all. I double checked all the settings and I can print to it from my applications when you are connected to the same network, but try to access the server of ePrint from the screen of the printer or the web interface cannot establish a connection.

  The printer is connected via a wireless network and can be printed from any device connected to our network.

  Everything indicates that there should be good. But can't seem to make bad connection ePrint. No error message not developed.

  The printer is on a network of b/g/n 2.4 GHz connected to a Netgear N600 DUal Band (WNDR3700 model).

  Version of the firmware of the printer is CLP1CN1232AR

  Any ideas? It does not appear to be blocked by a firewall, so really lost here.

  Hello

  Try to define an alternative DNS and check if that can help you:

  1. Tap the wireless on the top of the screen of the printer and look for the IP address is.
  2. Navigate to throguh IP of the printer, the web browser on your PC.
  3. Click the network tab.
  4. Under, click IPv4 wireless.
  5. Under the DNS Configuration, select manual.
  6. Set the address preferably as 8.8.8.8
  7. Set the e-mail address alternative as 8.8.4.4
  8. Click on apply to confirm the change.

  Now, turn the printer off and turn it back on and check for the difference.

  Shlomi