Connected, but can not visit Web sites

Similar Questions

• WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network

  I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you

  Firewalls are disabled on remote computers?

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• Cannot access Internet. It says I'm connected but will not display web pages.

  Original title: web no

  Unable to connect to the web says I'm connected but does not display pages

  Hello

  I suggest that refer you to the articles below that explain some troubleshooting steps basic to perform when you receive Internet connection problems.

  Why can't I connect to the internet?

  http://Windows.Microsoft.com/en-GB/Windows/cant-connect-Internet

  Why can't connect me to a network?

  http://Windows.Microsoft.com/en-GB/Windows/cant-connect-to-network

  If the advice above do not work, try to run a startup mode in minimum mode which must start Windows with only a minimal set of services and programs.

  How to do a clean boot mode

  http://support.Microsoft.com/kb/929135

  Note: After you perform a clean boot, be sure to check the "How to reset the computer to start normally after a boot minimum troubleshooting" section on the article above to start Windows normally.

  Thank you

  Legaede

• "due to an unidentified problem, windows cannot display windows firewall settings" fixed but still can not visit some sites and the laptop now turns off the coast on me. What should I do?

  I have an Apire one laptop with Windows xp service pace 3. I had to restore it to factory about 3 years ago. Some time after that the sound system began to slow and the Synaptics mouse stop working properly. I can move the pointer, but the left click does not work. It works in safe mode but not in normal windows. I used the Acer eRecovery for correct, but it did not work. I tried to download the driver for the mouse on the internet, but some how it could stop the download. I gave up at tring to fix. Some time in late March or early April, I couldn't access internet and after 22:30. I ran the diagnosis that is provided by internet explore and he said that the HTTP and HTTPS worked but the FTP did not work. AVG later told me my firewall is disabled and there was the possibility to reactivate it and I did. After internet explore stop allowing you to enter certain sites that I wanted to enter, I ran the Diagnostics again and he told me that a firewall client has been the cause of the problem. I tried to control my firewall setting, but had that "due to a problem not identified, windows cannot display the firewall settings". I thought AVG was the problem, so I have unintalled then he returned and attempted to access the firewall but got the same message. I typed in Google MySapce and found this site. I followed a few directions given to others in the thread started by joecarpenter33 and discovered that my firewall has been deleted and Base filtering engine has been deleted also. I downloaded and ran Malwarebytes ANti-Malware and SUPERAntiSpyware Free Edition and tdsskiller. MBAM has found a Trojan. The results of the analysis is less to:

  Malwarebytes Anti-Malware (Trial) 1.75.0.1300
  www.Malwarebytes.org

  Database version: v2013.04.10.14

  Windows XP Service Pack 3 x 86 NTFS (secure/setting network Mode)
  Internet Explorer 8.0.6001.18702
  Ziadie Berry: BERRY-LAPTOP [Director]

  Protection: disabled

  10/04/2013-17:44:54
  MBAM-log-2013-04-10 (17-44-54) .txt

  Scan type: quick scan
  Analyze the options enabled: memory | Startup | Registry | File system | Heuristic or Extra | Heuristics/Shuriken | PUPPY | PUM
  Analyze the options disabled: P2P
  Objects scanned: 271656
  Time elapsed: 43 minute (s), 42 second (s)

  The process of memory detected: 0
  (No malicious items detected)

  Modules of memory detected: 0
  (No malicious items detected)

  The registry keys detected: 0
  (No malicious items detected)

  The registry values detected: 0
  (No malicious items detected)

  Registry data items detected: 0
  (No malicious items detected)

  Files detected: 0
  (No malicious items detected)

  Files detected: 1
  C:\RECYCLER\S-1-5-21-4674304-3331980883-3375822000-500\$7832f44fdd2ba165f6ea01bec7f363fd\n (Trojan.0Access)-> quarantined and deleted successfully.

  (end)

  Malwarebytes Anti-Malware (Trial) 1.75.0.1300
  www.Malwarebytes.org

  Database version: v2013.04.10.14

  Windows XP Service Pack 3 x 86 NTFS
  Internet Explorer 8.0.6001.18702
  Ziadie Berry: BERRY-LAPTOP [Director]

  Protection: enabled

  10/04/2013 23:43:49
  MBAM-log-2013-04-10 (23-43-49) .txt

  Scan type: quick scan
  Analyze the options enabled: memory | Startup | Registry | File system | Heuristic or Extra | Heuristics/Shuriken | PUPPY | PUM
  Analyze the options disabled: P2P
  Objects scanned: 269636
  Elapsed time: 49 minute (s), 41 second (s)

  The process of memory detected: 0
  (No malicious items detected)

  Modules of memory detected: 0
  (No malicious items detected)

  The registry keys detected: 0
  (No malicious items detected)

  The registry values detected: 0
  (No malicious items detected)

  Registry data items detected: 0
  (No malicious items detected)

  Files detected: 0
  (No malicious items detected)

  Files detected: 1
  C:\WINDOWS\assembly\GAC\Desktop.ini (Rootkit.0access)-> quarantined and deleted successfully.

  (end)

  I ran the Diagnostics today after Internet explore and my other browsers stop allowing me to internet access. That's what came back:

  Diagnosis of last run time: 17/04/13 17:48:14 WinSock Diagnostic
  WinSock status

  attmpting error information to validate the Winsock base providers: 2
  error not all entries could be found in the basic services provider winsock catalog. A reboot is required.
  user redirection of information in support of the appeal

  Diagnosis of network adapter
  Network location detection

  Info to help home Internet connection
  Identification of network adapter

  Info network connection: name = Local, peripheral network connection = Realtek RTL8102E Family PCI - E Fast Ethernet NIC, MediaType = LAN, type = LAN
  Info network connection: name = wireless, peripheral network connection = Atheros AR5007EG Wireless Network Adapter, MediaType = LAN, type = Wireless
  Info both Ethernet connections and wireless available, ask the user for selection
  required user input action: select network connection
  Info Wireless connection selected
  State of the network adapter

  Info network connection status: connected

  HTTP, HTTPS, FTP Diagnostic
  HTTP, HTTPS, FTP connectivity

  WARN HTTPS: error 12029 connecting to www.microsoft.com: a connection with the server could not be established
  warn HTTP: error 12029 connecting to www.microsoft.com: a connection with the server could not be established
  warn HTTP: error 12029 connecting to www.hotmail.com: a connection with the server could not be established
  WARN HTTPS: error 12029 connecting to www.passport.net: a connection with the server could not be established
  WARN FTP (passive): error 12029 connecting to FTP.Microsoft.com: a connection with the server could not be established
  WARN FTP (active): error 12029 connecting to FTP.Microsoft.com: a connection with the server could not be established
  error could not make an HTTP connection.
  error could not make an HTTPS connection.
  error could not make an FTP connection.
   
  Still, he remains connected to the wirelesss connection, but won't let me access the internet. Right now I use a proxy to help, but access to the sites are limited.

  I used the tweaking software and my firewall is back but, I have yet to visit some sites and the laptop now turns off by itself.

  Hello

  Follow these methods.

  Method 1.

  Start the computer in safe mode with network and run a full scan of computer viruses.

  To start the computer in safe mode: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 2.

  If the steps above do not help, then try to scan the computer using Windows defender in offline mode and check if that helps.

  Search for spyware and other potentially unwanted software: http://windows.microsoft.com/en-US/windows7/Scan-for-spyware-and-other-potentially-unwanted-software

  What is Windows Defender Offline? : http://windows.microsoft.com/en-US/windows/what-is-windows-defender-offline

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Method 3.

  You can create a new user account and check. Once the new user account works fine, then copy the data from the old user account for the user account.

  How to copy data from a user profile damaged to a new profile in Windows XP: http://support.microsoft.com/kb/811151

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• After update I can not open Web sites other than facebook and youtube on my mac? Help! He says: connection refused.

  Hey after update of OS X El Capitan my laptop is unable to connect to internet via wifi except a few sites as Facebook and Youtube other than that none of the Web sites open on one of the browsers I tried to reinstall it but nothing happened, wifi works fine on all my other devices and internet are functioning normally If I connect to my mac on a LAN Port. Help why this phenomenon happens?

  Open System/Network preferences window and click on the Advanced button.  In the next window, click on the DNS button and see what is listed as a DNS server.

  You can try to use the OpenDNS servers by entering these two addresses:

  208.67.222.222

  208.67.220.220

  Save the changes, restart and relaunched Safari.  If you delete these addresses the default address will be back.

  

• pix501 vpn to connect but can not get anywhere

  That's how I'm Setup. DSL > linksys wireless router > pix 501. The wireless connects to a cisco 2924 > router 3com > line T1. The T1 line is used for a secure Web site to which we have access. I have the pix configuration, I can connect to the vpn and get an ip address, but I can only ping the external interface of the pix, nothing else. I want to be able to rdp in some machines on the local network, but I can't see them. The CLI I ping the router (10.29.30.238) of 3com, but not all the machines in the local network. (192.168.50.1) inside of the LIS, which connects the outside of her route (192.168.50.2) Linksys, the lan interface of linksys (10.29.30.102), which links outside the pix (10.29.30.103) and the inside of the pix (10.29.31.1), vpn clients receive an ip address of 10.29.31.50.59.

  Building configuration...

  : Saved

  :

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxx

  passwd xxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 10.29.31.0 255.255.255.0 any

  pager lines 24

  opening of session

  notifications of recording console

  ICMP allow all outside

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  external IP 10.29.30.103 255.255.255.0

  IP address inside 10.29.31.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP pool local Test 10.29.31.50 - 10.29.31.59

  location of PDM 10.29.30.0 255.255.255.0 outside

  location of PDM 10.29.31.0 255.255.255.0 inside

  location of PDM 192.168.5.0 255.255.255.0 outside

  location of PDM 10.29.30.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group 101 in external interface

  Route outside 0.0.0.0 0.0.0.0 10.29.30.102 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 10.29.31.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Sysopt connection permit-pptp

  Telnet 0.0.0.0 0.0.0.0 outdoors

  Telnet 10.29.31.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN PPTP-VPDN-group accept dialin pptp

  VPDN group PPTP-VPDN-GROUP ppp mschap authentication

  VPDN group PPTP-VPDN-GROUP ppp encryption mppe auto

  client PPTP-VPDN-GROUP VPDN group configuration address local Test

  VPDN group VPDN GROUP-PPTP client dns ISP dns ips configuration

  VPDN group VPDN GROUP-PPTP pptp echo 60

  VPDN group VPDN GROUP-PPTP client for local authentication

  VPDN username user1 password *.

  VPDN allow outside

  VPDN allow inside

  dhcpd address 10.29.31.2 - 10.29.31.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  Terminal width 80

  Cryptochecksum:xxx

  : end

  [OK]

  Yes, if you RDP on a server inside the pix, you can access a server outside the pix (in the 10.29.30.x network).

  There are a few requirements for this:

  -The server your RDP first needs to have a route by default for the pix (or at least a route to network 10.29.30.x via the pix)

  -The server outside the pix must have a route to the Pix. (He needs a route for 10.29.31.x pointing to the external of the pix interface) This can be done with "route add" in a dosprompt

• Can not type web sites in safari

  can anyone help, I can not search for a new web site in the search box. When I open safari, I can type the web page, but it doesn't then open the page. I can open all of the Web sites in my favorites, but if I click on the search bar, then it disable the bookmark page to allow me to type in a new search. Hope that makes sense, sorry for my lack of lingo good :-)

  Turn off the Suggestions of Safari in the preferences/Safari/search / uncheck Safari Suggestions.

  Latest issue of the Safari search bar

  http://osxdaily.com/2016/01/05/fix-Safari-freezing-address-bar-use/

• Help! A friend used outside visit my computer, now I can't visit Web sites because of the block of family security? How can he remotely sign out of my computer?

  A friend has visited my home, using my computer and now I can't acess sites due to safety for the family block.  I am connected to windows live using MY hotmail, but when I try to go to Web sites, it still shows my friends by email and wonder his password, saying: this site is blocked by the family. How can I fix it? What are the instructions that I have to give my friend to log remotely on my computer?  I turned off my computer and restarted it without success?

  Thank you

  Hi TysonMann,

  For us to further isolate the cause of this, please create a new user account on your computer with administrative access and check if this still happens. If this isn't the case, I suggest that you rename the name of the affected user account.

  Let us know what happens then.

  Thank you
  Gerard G.

• WMP110v2 network connection, but do not open web pages

  I have a Dell 2 GB of Ram and XP PC with the latest service packs and updates. No apparent reason, I had a little difficulty with the installation but after only two tests, but I the WMP110 to properly install and connect to my wireless connection. I use a D - Link Wireless Router N DIR-615 and my other wireless devices are running smooth.

  My problem is that my wireless connection will not go to the internet and I tried to use the Linksys monitor, but also Windows network utilities to check the problem and run the wireless but not connect me. The Web page tries to load, but then ends with the screen 'diagnose connection '.

  I think it will be easy but don't have yet to see a post explaining this problem and I don't know what to try next. Any help would be appreciated.

  Thank you for your interest in Klatch - I got it working well. As the biggest computer frustration usually boils down to a few clicks. For those who have the same problem, here is what has held back me.

  Until I'm able to get a connection I had to find some time to figure out how. Until I went in: WIFI - right click on the wireless connection, and then select PROPERTIES - click on the tab that says WIRELESS NETWORK -, PROPERTY - and then, AUTHENTICATION - once you see a checkbox indicating "authentication enable 802. 1 x for this computer"- UNCHECK this box. You will be able to connect to the wireless network.

  Then, my next problem and the reason for this post was that my network is connected, but I could not display web pages. This solution is buried in the manual on the CD itself. To resolve this issue, you must go into the DEVICE MANAGER to view the Linksys WMP110 under network adapters. Click on in the driver, then go to the ADVANCED tab. Here, you will see a list. You will need to click on the NETWORK TYPE. You should see two types of networks that you can select. The default value for mine was INFRASTRUCTURE. I had deselect this and select AD-HOC instead. My web pages now appear quickly, and I can browse the internet with wireless only!

  My setup is a N D - Link DIR-615 wireless router. I run Windows XP Home Edition on a Dell system. My type of security is WEP.

  Hope this info may help others.

• Can not manage Web sites on the Cloud Creative

  When I try to manage my websites on the cc Web site it goes to a page saying "Page not found sorry, we did not have this page.". When I try to log in BC Site areas I get "ERROR: the web site you want to administer is not found." Is there something wrong with my setup? He has always worked until now.

  Are you going to http://creative.adobe.com, I can access that.

  Could you please try another browser and also try to clean the cache and browser history.

  -Thomas yannick

• Palm TX can connect but can not get any web sites

  Hello

  I just got my Pam TX to connect to my home network, manually entering the IP address.  Now, he instantly says "unable to find the requested page" as soon as I get a web address.  Am I missing something?

  Is there something that I need to upgrade?  I have a Verizon FiOS, connection WEP router...

  Thank you very much

  HA

  Instead of entering the name of the computer, try to enter the IP address for it on your network.

  I strongly suggest setting "static IP" for your TX and PC in your router.  This will ensure a better connection for a HotSync wifi success.

  WyreNut

• Can connect but can not map or access by car.

  I had to close my network because co to replace the transformer. When I restarted the network 2 of my computers worked fine the other 2 cannot access drive maped. I restarted the 2 that will drive network, tried remapping drive access (got error message Impossible to fing server) find computer opportunity can fing server but cannot access it. Can ping server and get in return. If I created a new network connection can access hard disk by using the IP address. check the rights, passwords and sharing as well as the permissions of the user to the file. Any ideas.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://TechNet.Microsoft.com/en-us/WindowsServer/bb512919

  Hope this information is useful.

• Windows 7 recognizes a wireless network; trying to connect but can not

  My laptop with Windows 7 detect my home wifi network. I typed in the access code and my computer attempted to connect with him, but it still fails. I ran the store and followed all the steps, he gave me. I unplugged unit, waited 10 seconds, plugged it back in, and represented the resolution of problems, and it came with the message "Windows cannot solve your problem of wireless connectivity."

  How can I fix it? If necessary, I can provide more information in the troubleshooting report.

  Hi Mellodramatikk,

  -You receive an error message after you type in the access code?

  You can try to start your computer in safe mode with network and check if you can connect to the wireless network.

  . To boot to the desktop in safe mode with network keep tapping key F8 during restart. Once you see the option to start it in safe mode with select network and press ENTER.

  Access the link to learn more about how to start the computer in safe mode:http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

  Also, check if you have any third party security installed on your computer and try to temporarily disable the security software of the computer and try to connect to the wireless network. If you are able to connect to the wireless network after you disable the security software, you can contact the manufacturer of security software and check if you need to change the settings. Later, re-enable the security software.

  Post back with the above information and let us know the result.

  Thank you and best regards,

  Srinivas R Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• I can connect but can not open emails?

  I thought it was my desktop computer, given that I was able to open e-mail from other computers, but now I can't even open my emails from other computers. Again, I can connect to hotmail, but it won't allow me to open the emails?

  Hello

  When you go to your email address,
  you are ALSO automatically entered in another microsoft service?