Connection error to the login server to view while adding the view composer

Similar Questions

• Want 4500: Connection error! The printer could not connect to the server

  Connection error! The printer could not connect to the server!

  Cannot set up eprint or update the driver. Ever been on the forums and do not understand what to do!

  I am successfully connected to my router and can print from my pc and my ipad with airprint.

  PC "will not find"the printer either for purposes of updating

  What I need to change the DNS. If so, I don't know what it is or how to do it!

  I went to the ip address but was unable to click on "wireless (802.11)", as recommended by a last response forum, as the next low 'status '.

  Can anyone help?

  Very frustrated customer :-(

  Hi @roopuk,

  Thanks for getting back to me.

  Sometimes the manual DNS 8.8.8.8 / 8.8.4.4 won't work in some configurations of network users.  Try the same steps as described above, but this time use the following parameters:

  Manual preferred DNS Server: 209.244.0.3
  Auxiliary manual DNS server: 209.244.0.4

  If you encounter the error, as before, we take our proverbial gloves off to try a more intensive troubleshooting.

  What is happening, it is that your router allows your printer connection that to enable wireless, but not a secondary connection to Web services.  In order to get these devices to 'shake hands' a second time, you may need to enable DMZ mode on your network through the router's built-in Web server.  HP does usually not this configuration for its customers as errors can cause serious network problems, but I can certainly post the info you need on your router or the ISP of the staff support company so that they could help you directly.

  Here is the information that you need for your provider service to open ports on your router/modem...

  -Multicast must be enabled
  -Hello enabled for AirPrint (relevant for iOS and Mac OS users)
  -Mac filtering should be disabled
  -Also, make sure that your router's firmware to date if
  necessary
  - The dmz on the router mode and turn it on to the printers IP address: _

  Ports to open are: Eprint and Apps

  Incoming Ports.

  UDP
  80
  443
  ------------------
  Outbound ports

  TCP
  5222
  5223
  -------------------
  Once they are open, you should have no problems connecting to services web eprint on your device.

  I would like to know how it works for you.

  Kind regards

• Installing the Server VMware View Composer

  Hi team,

  Need help,

  I'm trying to install VMware View Composer server but I can not create my ODBC connector, can you pls help me to do this task.

  I get this error message

  

  (1) to connect to the database and the new query

  use 'ViewcomposerDbName '.

  exec Sp_changedbowner 'viewservice.

  (2) the right of the database and allow the sql and windows Authetication

  See the screenshot

  (3) lFailing Stil? Go to, click on Sql Server for management (on the left side) > Sql Server Logs > current view them if it connects

  It should be

• Connection error Active Directory Windows Server R2 2012

  Hello

  That's my problem, I have two servers both running Windows Server R2 Datacenter 2012 I installed AD - DS on one of them and allow the installation to configure the DNS settings, this server is also a DHCP server. On the server I want to connect to AD, I address DNS pointing to my AD server which is 192.168.1.60 and it's also getting an IP address from the DHCP server. But it connects to Active Directory, when I try the ping command on the domain name which is yewman.email he's trying pings an external IP address (which is my public ip address because I also have the yewman.email of real estate) how to fix this? It's the mistake of connection AD:

  Note: This information is intended for a network administrator.  If you do not have your network administrator, notify the administrator that you have received this information, which has been recorded in the C:\Windows\debug\dcdiag.txt file.

  The following error occurred when DNS was questioned about the resource record (SRV) service location used to locate an Active Directory (AD DC) domain controller for the domain "yewman.email":

  The error was: "the DNS name does not exist."
  (0x0000232B RCODE_NAME_ERROR error code)

  The query was for the SRV record for _ldap._tcp.dc._msdcs.yewman.email

  Common causes of this error are:

  -The DNS SRV records to locate an AD DC for the domain are not registered in DNS. These records are automatically saved with a DNS server when an AD domain controller is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses:

  192.168.1.60

  -One or more of the following areas do not include delegation to its child zone:

  yewman.email
  E-mail
  . (the root zone)

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Cannot connect - error loading the database...

  Hello

  Since last night find it me impossible to log in on my Skype.

  He puts me "error loading the database. Skype." It is possible that another instance of Skype to use it.

  I have reinstalled Skype, restart my pc, close all programs that could use it.

  My husband get a leverage son skpe without pb so it comes well d a pb with my nickname... going to Word of the change back I. Despite all this, I still have the same message that appears! 1

  did anyone have the same pb? and how he made it?

  Please pour your help!

  Rrbonjour

  so I did well the manip: Task Manager, process shutdown Skype.

  then relaunch the application, but it gives me the same result...

  I made a new system more earlier but it's restore gives me the same result...

  I asked a third person open my account on another pc and ca works... so it just my pc, not a hacking, (already it reassures me!)

  My spouse does so well to open Skype with his nickname but I still nothing.

  Application rattachee a Skype name can she used Lun?

• No server found view composer

  I think that the solution to the problem can be simple, but I'm not find clue in the documentation I see.

  I'll put up a view view environment 4.5. I have a vCenter server, SQL Server on the same environment as View Composer and Connection manager. There are no firewall in the environment or enabled on the operating system of these machines. The View Composer and the connection manager are on the same VM.

  Problem: When I try to add the vcenter Server, it throws the following error "no composer view server Found. Either a bad port has been entered or a network connection error occurred", as shown in figure below.

  

  My research in VMTN and Internet, has pointed out to me that the problem may be with configurations of network or administrator rights, but as mentioned before all these machines are on the same VLAN and there is no firewall. Also I use a single user from the administrator of domain for all these machines., (this is a laboratory environment, this is why we can afford to do).

  Your suggestions are very appreciated.

  Thank you.

  Kumaran

  The composer of the view must be installed on the vCenter server and not on the display connection server.

• Connection error during the import of metadta in OBIEE 11 g

  Hi all Experts,
  
  I'm trying to import metadata from Oracle 11 g R2 database (supported Version) to OBIEE 11 g R1 (11.1.1.5) physical layer Admin Tool, when I select a source of data, such as connection type OIC 10 g / 11 g returns an error, connection failed , alll of oracle database services are up and running. (My repository creation utility is run successfully on this database when is install OBIEE 111 g)
  
  Also, I created an ODBC connection to oracle database 11g R2 import, the connection is created successfully, to return the same error message with all sys, s/n users.
  with other data source when I tried as of SQL SERVER 2005 there is no error and can import successfully.
  
  Please give some solutions
  
  Thank you

  Hi reda,.

  Paste the file tnsnames.ora in these two places,

  {Oracle_BI1} \network\admin directory &

  \Network\admin {oracle_common} directory

  Rgds,
  DpKa

• Connection error to the web proxy signer

  I get the following error when I try to sign the cod files:

  "Error connecting to the web proxy signer."

  RIM sign services down?

  RBB = 1993325328http\: / /www.rim.net/Websigner/servlet/BBApps
  RRT = 1993325328http\: / /www.rim.net/Websigner/servlet/Runtime
  CPR = 1993325328http\: / /www.rim.net/Websigner/servlet/CryptoRIM

  I think I got the answer in the meantime:

  http://isthesigningserverdown.com/beta

  If all goes well they will be until shortly after.

• Connection error to the catalog in the Console of the AIS

  Hello Experts,
  
  I get the following error message when you try to connect Console AIS catalog
  
  ODBC error [DataDirect] [ODBC Oracle Wire Protocol driver] [Oracle] ORA-01031 insufficient privileges running the catalog script C:\Hyperion\AnalyticIntegrationServices\ocscript\oc_create_oracle.sql failed
  
  Any suggestions would be a great help.
  
  Kind regards
  Sudhir

  Check the privileges of the account that you use to connect to Oracle, it seems that the account you are using is not ' t have enough privileges to run the sql.

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Connection error using the ID of the company on iOS

  Hello

  I can't connect to my Creative Cloud libraries using an ID of the company on iOS.

  It works well on Android?

  Is there a fine adjustment to help iOS connection?

  I guess that's an internal issue in the workflow of authentication (supposed to be SSO) between our AD company and creative cloud enterprise environments.

  It works on PC but not on Mac with CC Desktop App too, but it works well with Safari.

  It works on Android device but not iOS when inside the company, but outdoor work...

  Our team work network & IT on the question

• I have a problem with 'url not valid and cannot be loaded' also the site accuweather on my toolbar does not load, all I get is a sying note "connection error". The google homepage, I've always used is empty at the start of firefox.

  I had a problem where firefox crashed while the closing bbc iplayer site last night, I reebooted firefox and everything seemed in order until this morning. I cannot use the default Web page of google but you can use the uk version. When you try to solve the problem I get the "invalid message url."

  • "Clear the Cache": Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.
  • 'Delete Cookies' of sites that cause problems: Tools > Options > privacy > Cookies: "show the Cookies".

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the Add-ons is the cause of the problem (switch to the DEFAULT theme: Tools > Modules > themes).

  • Makes no changes on the start safe mode window.

  See:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Solve problems with plugins like Flash or Java to solve the common problems of Firefox

• How to fix VMware View Server certificate revocation check connection error?

  Dear community,

  For about 2 weeks, I feel a revocation of the certificate check error in our environment Horizon see 6.2. The strange thing is that, within 12 hours about two (replication) connection servers and the vCenter Server / server of composer (on the same machine) are considered as having invalid certificates, even if, in fact, they are valid (CA certificates). We use no security servers.

  The view admin console shows the following for servers connection:

  The server certificate is not approved.

  The server certificate cannot be verified.

  For the vCenter, he said (that I have validated manually the certificate):

  No problems found.

  Certificate is not approved, but the thumbprint of the certificate is accepted.

  With the connection series on 'full', States that the login server logs for the vCenter server:

  TRACE (B 17-0 - 0E98) < VCHealthUpdate > [NativeKeyVault] validateCertificateChain response: {result = FAIL, EndEntityReasons = cantCheckRevoked, ChainReasons = invalid, SelfSigned = false, EndErrorCode = 16777280, EndInfoCode = 258, ChainErrorCode = 16777280, ChainInfoCode = 256, PolicyErrorCode =-2146885613}

  As far as I can see there no similar entries for login server certificates in the newspaper.

  At the moment I am under the environment with composer and vCenter certificates manually valid and invalid connection (red) server certificates (as view clients and browsers are not disabled).

  I already checked that I am able to do everything 'green' again via setting the registry key 'CertificateRevocationCheckType'2 (as described here Configure the server certificates certificate revocation check). This brings me to the conclusion that one of the intermediate certificates cannot be validated. So, I had the information a "version" of an intermediate (intermediate certification authority) certificate has been revoked. There seems to be no coincidence - like the time point is as well, but this particular version does not appear to be used in the servers of my connection.

  However, even with full logging enabled, I can't information which (intermediate) certificate cannot be validated and why. I expected to see something like 'OCSP verification' or 'check the CRL' but I can't find it in the newspapers. However, I noticed that one of the intermediate certificates lacked the OCSP URL (even if the field "Authority Information Access" existed). Of course I updated the certificate with a version that contains the OCSP URL, but it has not changed anything.

  In addition, I checked manually all of the certificates in the chain with openssl (for OCSP) and CRLs as well, but everything seems to be OK (all URLS are accessible and no opportunity of certificate has been revoked). Actually, I do not interpret the error as "that the connection to the server is an invalid certificate because it has been revoked", but "it cannot check if it has been revoked. The servers do not need a proxy and nothing configured, so (I checked the proxy settings system context, also).

  For now, the problem is not critical, such as 'red' status connection server has no effect on our customers and so I could turn off certificate revocation check (or switch to check that the certificate of the server (2)). But of course, I would really solve the problem.

  Is there someone who can give me a hint on what to check, for example, how do I know which certificate cannot be controlled and why? Someone had the same or a similar problem? Support VMware is working on the problem as well, but they seem don't know is not the problem, either.

  I appreciate the thoughts and responses! Thank you!

  Best regards

  Fabian

  Dear community,

  During this time, I was able to correct the error described at the beginning of this thread. Jump to the end to see what could probably help you...

  1. At first, I installed an additional standalone VMware View Server connection in order to check the following related certificates:
     1. VMware support always told me to renew my certificates because they "were not valid" etc. - even if in fact they were (like external URL calls and attested manual verification and tests).
     2. That's why I created new additional certificates for the login server and configured to include the vCenter even as my production environment - only difference was I didn't inlcude the composer who runs the server vCenter himself.
     3. The result was that the server was "green" including both the vCenter Server certificate which could be 'not reliable' by the environment of production - strange, huh?
  2. After I reset the additional server to a turned wink where connection to the server was not yet installed (before that, I uninstalled the connection to the server in case there is information in vCenter thereon) and reinstalled as a replica of the production environment server. Somehow I expected this, but still quite strange the vCenter Server (and composer) now again was considered "invalid", even if the certificate of the server connection itself considered still valid and green. For test purposes, so I put certifice revocation checking on '2' (only one server certificate check) - but only on the 'old' production servers' and 'magical' everything has been considered valid. So as I see it, there seems to be some sort of information stored on the 'old' connection servers that makes them believe that invalid certificates and that the information is replicated on the third server unless I lower the revocation of the certificate controls on these servers. Altervative explanation could be that VMware View does not accept certificates with aliases that do not include the 'real' server name - that is / was in fact certificates the old servers connection. The new server certificate connection included the real name and the alias. I understand if this is the case, but then I expect that it be documented somewhere (I have not found this information) and also wouldn't understand why it worked without problem for several years before.
  3. After finding that out, I created new certificates for the 'old' connection servers, including aliases and real names and replaced the certificate on one of the servers (and restarted the login server) - only a few successfully. Once I put the revocation checking on '4' again on this server, the login server certificate was still considered valid, but not the vCenter and certificate of composer.
  4. Now, I've uninstalled the old login server (removed from the view) and reinstalled completely (including an update of the 2008 R2 2012 R2 OS) and after I have it reintegrated into the environment, everything remained green - as long I have will activate revocation checking on the second login server "old." This is why I did the same with this (completely reinstalled and reinstated it) and now everything is green with the revocation checking enabled on all replicas of server connection.
  5. The next step I uninstall the additional replica because I created only for troubleshooting purposes.

  So what will no doubt help in similar cases:

  • Reinstall the servers of connection one by one, including:
  • Uninstalling html access (if used), uninstall the login server to view, uninstall 'VMware' AD LDS Instance.
  • Removal of the connection to the server of replication group: run "s - r s uninstalled_ vdmadmin.exeservername" on one of the servers connection remaining.
  • Reinstall/Update OS (may not be necessary, but I did not test that)
  • Reininstall, return to the login server replica. If you used the certificates which included only the alias of the server I recommend you to create new ones, including the name of the server as well, but maybe it's not necessary as well. If you want to keep the certificates which only inlcude the alias it will be necessary to install this certificate after the first replication of the servers (see below).

  My question for technicians of VMware/developers: It is supported to use certificates include only the server alias. Otherwise why it worked before and where is it documented? Where are certificate cached information so that simply replace the certificate was only some, and not a complete success (see above). FYI - when I paired initially replicas that I had to install the CA (including only the pseudonym) after the first replication - now with certificates (including the server name and the alias), I could install the certificate before you replicate (= the login server installation).

• Problem in sending the request to the server, MDS started after expired connection error

  Hello

  I have a problem when sending request to the server. I need to manage the time of connection error. When I send a request from my device to serve and connection time-out error, I need to send the request back to the server.  To test this error, before sending the request, the MDS quit and then I try sends the request to the server. After 2 minutes, the appliance up Connection Timed out Error.

  Now when I start the MDS and refer the request to the server, the request sent when the connection has expired also reached the server. (Totally 2 request are sent to the server).

  What is the behaviouir of MDS? If so how should I handle this.

  or have I missed something on my side?

  I use BlackBerry 4.2.1 JDE with SDM (4.5.0)

  Thanks in advance.

  (Note: see this link for the behavior of MDS.)

  Hi all,

  I finally found the solution.

  Everytime I go to start the net, I check that the connection is available or not by using below codes...

  HttpConnection conn=null;try    {    conn = (HttpConnection) getConnection(myURL);      if(conn == null)     {           Inform the user the process is in offline       }     catch(Exception e)      {      }      finally      {                try                {                    conn.close();                    conn = null;                }                catch (Exception e)                {                    conn = null;                }            }
  

  When this function is execute the connection is not closed properly.

  After that I got the connection error, start the MDS, meanwhile runs unclosed connection.

  Now, I removed the check above, its works very well.

  I made a mistake. Finally, I saw that and correct it.

  Once again thanks for all your opinions and answer.

  Sorry for my English.

• Web Services problem - server connection error

  Hello world.

  When I try to enable Web Services, I get an error. I am connected to internet (WiFi) and the connection is ok.

  The error is:

  Server connection error

  The printer could not connect to the server. Check the internet connection and try again, or enter a proxy address.

  I do not have a proxy, and the internet connection is ok! Why do I have this problem?

  Thank you very much.

  We will set an IP address of the printer:
  
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the bridge and the first DNS. Let the second white.< the="" dns="" could="" be="" your="" problem.=""  if="" this="" does="" not="" work,="" try="" google's="" dns="">
  -Click 'apply '.
  
  Now, stop the router and printer, start the router, wait, and then start printing.
  
  After that, you will have to redo 'Add printer' using the new IP address.

• Server connection error

  Series of photosmart HP 7520. -J' am trying to scan a document to send and keep getting the message "server connection error" despite the fact that WiFi is showing as connected. I'm not very good with technology! Can anyone help please?

  Hello Alleycat1. I understand that you have a problem scanning to e-mail, about the connection to the server. If you follow the troubleshooting in this HP document, the issue should be resolved, as it contains troubleshooting for this error message: http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?sp4ts.oid=4022328&spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02524629-11%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  If these steps do not resolve the problem, I would like that you follow these troubleshooting steps (assuming you're the App on the front panel of the printer):

  1 Select the Web Services on the Panel forward, then settings.
  2. Select "delete web services" and wait as the services to be eliminated.
  3. Once finished, you will return to the home page.
  4. Select the Web Services icon on the printer and go through the steps of installing Web Services once more.
  5. you will receive a more recent code. Later, you can use this code to add the printer to your account eprintcenter.com hpconnected.com / using this code.

  6. you can, or that you may create another email address.

  7. try a different scanning to e-mail using the app.

  Please notify me when all troubleshooting is done, and I'll continue to help you if necessary.

  Mario