Connection LED light to a table and lights if there is a number.
I am trying to allow a light to be attached to a table or a graph, and when a constant is reached or a constant exists in the table, the light.
For example, I have random numbers to come in table or graphical waveform and any number greater than 8 will trigger the LED light upward.
Can someone help me.
Thank you!
Tables tables 2D of channels is, so you can't do math directly. I assume that you have the original digital painting also as a 2D array. Simply use the "superior to" followed "or of the elements of array.
Tags: NI Software
Similar Questions
-
BlackBerry smartphones how different colors of man LED light is there?
I'm sure it's in the manual, but have not had the chance to watch it yet.
Anyone know? I noticed it was blue, now, it flashes green... unless I guess things.
Think I saw red as well... not sure.
Check out this article that the 4 different States
-
Portege M800: How to turn off the LED light of the multimedia and the touchpad?
Hello
I have Toshiba Portege M800.
I want to know, how can I turn off the light of multimedia and the touchpad
Thanks in advanceHello
I m not M800 owner but I ve got an another Toshiba laptop and these LED lights I can turn market in the BIOS and in Toshiba HWSetup.
The HWSetup is placed in Toshiba help optimize them and the settings are in the tab 'enlightenment '.See you soon
-
Hi all
Problem: Build a VI to display a string in the table of the lights. Each letter must be posted in a separate table and letters must move from one table to the other in the direction from left to right.
I did program mentioned above but it does not work. Can you tell me what is the problem?
There is no error is indicated in the program. If someone knows about it please try to find solutions and help me out of this problem.
I have attached my program with this message.
Thank you in advance!
(1) FOR loops are your friend here. You can make a slight restructuring using loops, and then you will have less mess to deal with, the inner loop through tunnels of autoindexing to make it even simpler.
(2) I would only treat the numeric values of the characters. So go terminal of control of the chain, the capital letters and byte array to before the outer loop. You can use a size of Board over there to tell how many times the outer loop to iterate.
(3) the Index table is extensible. So you only need over the index of the first, and it will increment itself, as it develops.
(4) you need to finish the lookup table (table 3D)
-
lighting of 3 leds using the sequence meal and time delay VI express?
run the vi and a LED light, 1 second later, the 2nd led should light, 2 seconds later the 3rd led must light up then everything must stay on for 3 seconds, I need to use a flat sequence with 3 images and express time in each image
Tips or advice would be grateful im a little new to this iv not been mess autour with her and to this day no luck
Nevermind I got it
-
Red LED light flashes 3 times, two sec pause and so on
I have a Dx5150 MT, Windows XP with this problem:
Red LED light flashes 3 times, two sec pause and so on.
According to http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00868914&lang=en&cc=us&taskI...
Reinstall the processor, but the problem persists.
Solved by removing the battery.
georgopgr wrote:
I have a Dx5150 MT, Windows XP with this problem:
Red LED light flashes 3 times, two sec pause and so on.
Reinstall the processor, but the problem persists.
-
LED light - what do the colors mean and can I customize who?
Hello, I may have a phone user bit spoiled because my previous phone was Xiamoi Mi2s with MIUI and I must tell you that this system has great customization options. You can assign different sounds to different events and notifications. Choose what color flashing LED means whatand a lot of other things. If I look right then on Xperia, there's that one about LED light option - turn on or off. I guess I have to download an app store to play to customize the colors and there reason for behavior? Thank you
That's right, even if a few apps lets you choose the clear color of notification, such as Yahoo mail, Whatsapp, etc.
-
How to set my keyboard led lighting. Enable, disable, how long to stay on after the last shot. I had the functions to do this before or I've forgotten or lost abilities. And FN & Z do not work. I would have the size as a Properties window opens. It was about 12 tabs for different frunctions. «Please help me someone...» I would be grateful! »
Hi Aldo,.
What is the manufacturer, brand and model number accurate and complete from your computer? What is the manufacturer, the brand and model of your keyboard? We can not help you without more information on your specific computer.
If you want to go faster, simply contact the Group technical support from the manufacturer of the computer or go to their support site and ask them or look for this issue. If you provide us with the above information, we will go to their website and see if we can find the instructions (if we can) – and they will be able to do it faster and better than we can. The choice is yours.
I hope this helps.
Good luck!
-
I have a Brother HL2140 printer. When I turn it on and press the go button, all 3 LEDs light up and then begin to Flash. I need help...
The brother of contact support.
-
G5 will not start. LED light on. Fans before working.
Early 2005 G5. running 10.5.8.
G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.
Sam
Some of the fundamental things include the pram/clock battery replacement
since they may be dead; then with a power failure, sometimes the Mac
do not restart. Usual power management unit & reset NVRAM/PRAM are
methods that sometimes also used as a troubleshooting measure.
• Reset the Mac chip power management: (see SMU)
http://www.thexlab.com/FAQs/resetpmchip.html
• How to reset NVRAM-LANDAU on your Mac - Apple Support
A hard reset can sometimes be used, where the power is disconnected
the logic board and power removed from grill; Then push the Start button / stop.
(But maybe not. Several PowerMac computers, I had, some people found this helpful)
You may also remove and reposition cards and other items
the inside of the case, to be sure they are connected properly. Be sure to not
In short anything, due to the static load or residual power in the circuits.
The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.
can help to put it on again. Also sometimes the power supply has some faulty fans,
circuits or capacitors, so they can be troublesome to repair or replace.
Good luck in this case!
-
I recently bought the hp with i7 proceessor envy and I want to know if the 23 inch screen IPS LED - lighting HP Pavilion monitor will be compatible with i7 ENVY 700-311 HP Desktop processor?
Until the entry of the screen is the viudeo output which is available on the desktop PC, it will be compatible. The dekstop PC has VGA and DVI outputs. Just use a cable that allows you to connect both devices and you'll get the video.
I see that the screen has both. I highly recommend the digital video input instead of the VGA NICU.
You will need a DVI cable.
-
How can I manipulate a 2D led array so that the LEDs light up in different ways?
Hello everyone. I hope someone can help me.
I have an array of leds of dimension 2d 4 x 4. I want that the leds light up in two different ways.
One, I want the leds light upward from left to right. In the following order:
0.0 0.1 0.2 0.3
1.3-2.3 3.3
3.2 3.1 3.0
2.0 1.0 1.2 1.1 2.2 and 2.1
So in the end the entire table turns.
The other, I want the leds light upwards from right to left. In the following order of the order:
0.3 0.2 0.1 0.0
1.0 2.0 3.0
3.1 3.2 3.3 1.3-2.3
1.1 1.2 2.1 and 2.2
So in the end the entire table turns.
Any help will be appreciated.
-
My Sony Vaio model PCG - 61611L Green LED lights up but nothing happens
When I turn on my Sony Vaio model PCG - 61611L, the Green led lights up, but nothing goes well. The laptop is 2010 and is never abused, so I don't know what happened. It just started this making times and now I can't turn it on at all. Any suggestions?
It seems that you have no POST issue. Is it the caplock/numlock light up when you press it? Did you try to connect to an external monitor to see if it's a matter of display dim? If this is no a POSITION, try reinstalling the ram or using one at a time... you can also remove the optical drive and hard drive to see if you can start any found nail system. If you can not always unity would require service...
-
VPN no LED light on 891 new routers
I have just four new C891 routers and configured them to double simultaneous GRE - over - IPSec tunnels each, and although the tunnels seem to be upward, encryption and routing the data very well, the VPN light on the front panel of the unit is off.
I use two secondary port WAN Gigabit0 interfaces, since my two tunnels the C891 WILL go to two physical sites completely different (each with a 3845 router), one for a voice VLAN and one for a local VIRTUAL data network. I do not use the public Internet, but rather a private WAN microwave as my return, and the need of subinterfaces was motivated by the fact that there are two completely different numbered IP networks for interfaces the 3845 each connect to the WWAN, which the C891 wouldn't let me run tunneling IPSec from an ip address 'secondary '.
I suspect that the reason why the LED lights is because there is not on the interface itself, but on the subinterfaces rather crypto and different encryption card on each subinterface. Is there something I can do to force the LED to light?
Maybe it's this bug? CSCsv01869
HTH
-
BlackBerry Smartphones LED light
The Green LED light flashing all the time keep, I tried to change the battery and disconnect the Bluetooth connection without difference. When I turn off the Mobile off connection, the light is off! someone has an idea?
Thanks in advance.
Go to the Options - screen/keyboard
flashing 'Coverage led' on 'Off '.
Save the settings.
Maybe you are looking for
-
When Norton Toolbar works with the latest version of Firefox?
Toolbar has been disabled when I updated, but I really have trouble using Firefox without it.
-
How to put icons ICS on GB.42?
Hi... I want to change the stock icons to Go with ICS, s?... saw a post by a user: Posted by adoet_t http://Forum.xda-developers.com/show...php?t=1481769 Thank you...
-
ConnectionFactory.getConnection () returns null.
ConnectionFactory connFact = new ConnectionFactory(); ConnectionDescriptor connDesc = null; connDesc = connFact.getConnection(----here goes my url String----); Hi all In the code posted above, number In Line 3, reason for which the null value is retu
-
New UCS-C210 problem with video monitor output
Hi all We just bought a new Cisco UCS C210 M2 product for our CUCM migration to Virtual Machines. We plugged a HP monitor and a USB keyboard to start work with the UCS. Then we plugged the server to the power supply and turn on the server, the fan wo
-
KEYBOARD LIGHT blackBerry smartphones... Help
HEY... I was jut wondering... is it possible to keep so the keyboard STAYS on? What is happening with the light... I do not understand it :/ I just got it, so if there is a way if you could tell me how! Thank you