Connection of 2 1310

Similar Questions

• Aironet 1310 bridges keep losing connection

  There was a similar thread about this last year and I tried what was listed in nothing doesn't.  I have 2 bridges Aironet 1310, one under a road bridge and the second as a slopes(32°) with the customers.  These worked great for almost a year, we have not had any problems to keep the connection.  They were not connected for the last month, but nothing has been changed on the configuration, when I got to the top they reconnected very well and worked for about an hour, they randomly don't disconnect with the same message in the log below.  Is there something wrong with them now?  Use the same antennas as before and are in the same exact location.

  newspapers of root bridge

  29 Nov 13:52:53.311: % DOT11-4-MAXRETRIES: XXXX customer package. XXXX. XXXX has reached max attempts, removing the customer
  29 Nov 13:52:53.311: % DOT11-6-CANCELLATION: Dot11Radio0, Deauthenticating Station XXXX of the Interface. XXXX. XXXX reason: previous authentication is no longer valid
  29 Nov 13:52:53.568: % 6-DOT11-ASSOC: Interface Dot11Radio0, Station Test sex toys. XXXX. XXXX again associated KEY_MGMT [Wpa2 PSK]
  29 Nov 13:55:16.260: % DOT11-4-MAXRETRIES: XXXX customer package. XXXX. XXXX has reached max attempts, removing the customer
  29 Nov 13:55:16.260: % DOT11-6-CANCELLATION: Dot11Radio0, Deauthenticating Station XXXX of the Interface. XXXX. XXXX reason: previous authentication is no longer valid
  29 Nov 13:55:16.550: % DOT11-4-MAXRETRIES: XXXX customer package. XXXX. XXXX has reached max attempts, removing the customer
  29 Nov 13:55:16.550: XXXX customer. XXXX. XXXX failed: reached maximum attempts

  nonroot newspapers

  November 29, 2010 13:52:55: % DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, lost parent: received deauthenticate (2) not valid
  November 29, 2010 13:52:55: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to down

  a RTS/fragmentation 4000 value means RTS/fragmentation never happens, because there way on the size of wireless frames. In fact :-)

  -77 is not very exciting signal strength. It is very good that this is but a little fluctuation and boom, signal becomes illegible.

• WiFi connectivity - the On / Off button on my Dell Vostro 1310 does not

  I can't have the WiFi button to enable the WiFi connectivity. I tried to update the drivers from the Dell site, but I thought that the material is missing.

  Any suggestions are welcome.

  Thank you

  Mervyn

  Hello

  As you say that you tried to update the wireless drivers, but were informed that the hardware connection Wi - Fi is 'missing '. I suggest that you either contact Dell or you could ask their Support Forums:

  http://en.community.Dell.com/support-forums/default.aspx

  See you soon.

• can I connect my hp deskjet wireless printer to my al 17 hp slate in one?

  I have a new hp slate 17 can I connect my hp deskjet printer 1310 all-in-one wireless on it?

  ang53 wrote:

  Sorry it's a 1510.

  Hello

  No, it has only USB connection, it does not support wireless.

  http://support.HP.com/in-en/document/c03775352

  To make to support wireless now, you have more material according to your existing network and it would cost more to buy a printer Wireless ready right now.

  Kind regards.

• HP PSC 1310 all in one more not print color

  Hey guys,.

  Recently, I replaced my color ink cartridge in my HP PSC 1310 after don't have one a few days and now my printer just won't print in color. It is aligned and it SHOULD be printing in color, it displays just everything in black and white. Y at - it a setting I'm missing or something?

  Thank you guys.

  SlamNetwork,

  OK, we know that's not the material of the PSC 1310, that we are able to get the color on the diagnostic print page. So that leads me to believe he has associated software, something in the settings of printing or drivers are causing to print in black and white only. Before you complete the steps, make sure that your Windows computer has all updates installed, check and see if there are those that could be installed. Please follow the steps listed below:

  1. disconnect the USB.

  2. remove the software HP PSC 1310 to uninstall from the control panel of your computers an option of the program.

  3. restart the computer

  4. make sure that all them that software PSC has disappeared from the list of programs, but also your HP folder listed under all programs in your Start Menu

  5. now, go ahead and download the software and drivers for your PSC (DO NOT connect USB until the software prompts you to):

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-75052-1&cc=us&DLC=en&LC=en&OS=4063&product=374578&sw_lang=

  6. go ahead and print a test page.

  7. If you are unable to print a test page or get no color, please run the HP Print and Scan Doctor- it was designed by HP to provide the users with troubleshooting and problem-solving features needed to solve many common problems encountered with HP print and scan the products related to Windows computers.

  Please let me know if you see now on your color prints, take note of any errors that you may encounter. I'll watch for your reply.

• connection of the antenna

  Hello

  I have a bridge 1310 with me, but the connections are curious to me.

  It's a BR1310G-E-K9 and I would push its antenna with an external, how do I connect to them (antena)? Also, does anyone know where I can the innovative deployment of the bridges in the open air, a Web site with pictures and things like that. I've been frustrated with yahoo search and Google search.

  The product you have has no capacity for external antennas. What you need is the AIR-BR1310G-E-K9-R, which doesn't have this capability.

  http://www.Cisco.com/en/us/products/ps5861/products_data_sheet09186a008022198b.html

  the connectors are RP - TNC

• Intermittent problems of wireless connection in Windows 7 Ultimate

  I recently bought Dell Studio XPS 1645 Windows 7 Ultimate edition. I am facing a frustrating problem with Wi - Fi. The connection is down and reconnect. I have the adapter Intel Wireless 5300 AGN and a router Dlink Wireless G I tried to update the latest drivers from Intel (Driver Version: 13.0.0.107), disabling IPv6 for all network interfaces, configuration of the wireless adapter to only use IPv4 and so on. I have 2 other systems with XP Professional on my home network. As soon as I start my Windows 7 laptop, the chaos begins. The router restarts every few seconds, other disconnected systems and so on. I have not found so far any solution on the internet that could solve this problem.

  Other observations that may help to understand my problem:

  1. once my wireless adapter disconnects, the ping my router fails. It tells me whenever my system is asking for a new IP address.

  2 Event Viewer displays multiple entries, which indicates that the DHCP could not get an address. The error looks like as follows:

  The lease of the IP address 192.168.0.100 to the network with the network 0x00216A934EE2 address card has been refused by the 192.168.0.1 DHCP server (the DHCP server sent a DHCPNACK message).
  

  It gets an IP address later, but I do not understand why my adapter tries several times to get a new address every few seconds.
  DHCPNACK is the negative acknowledgement which router returns Win 7 DHCP client. I believe is that the client requests an address that is not available. Why would be client DHCP running on Windows 7 this?

  3. I have a D-Link WBR-1310 wireless router G with the latest firmware. Web sites of the reports that it is compatible with 32 and 64-bit Windows 7.

  4. I see no problems with the wired connection.

  As I type this, which could take a few minutes, my wireless connection rolled 7-10 times. All ideas, experts?

  If you need more information, let me know.

  I was able to find the main cause of intermittent disconnections on wireless interface. According to the information I have collected on internet forums and my research, I did as a result of configuration changes that have stabilized the connection. These settings work when you have N wireless adapter and a B/G Router:

  The wireless adapter settings:
  
  The driver for the most recent driver update.
  Access the properties of your adapter wireless network and sharing Center.
  Click on "Configure" and select the "Advanced" tab Make sure the following is in place:

  1 channel 802.11n for bands of 2.4 and 5.2 width are set to 'Auto '.
  2 disable 802.11n Mode
  3. Ad Hoc channel 802. 11b / g should be 1 or even that you have configured on your router.
  4. Ad hoc QoS Mode, keep WMM disabled - disable the router too. My wireless connection is stable once I made this change.
  5 fat Channel intolerant - disabled
  6. mixed mode protection - RTS/CTS enabled
  7 roaming aggressiveness - the lowest
  8 flow Enhancement - active
  9 transmitting the power - low
  10 mode wireless - 802.11 g

  Uncheck the box "Allow the computer to turn off this device to save power" on the tab "power management."

  Other Configurations:

  1. disable IPv6 completely. Uncheck 'Internet Protocol IPv6' in the wireless connection properties window. Repeat this for every other network connection you have.
  2. make sure you have the latest firmware installed on your wireless router.
  3 CTS Mode should be disabled in the configuration of your router 'Advanced Wireless' auto and WMM function.
  4. use only the WEP or WPA Wireless Security. Other methods have problems with 802.11n adapters.
  5. do not disable broadcasting of the SSID of your router. You don't need when your network is secure.

  I hope this helps.

• 3702 AP loss connectivity to WLC in local mode

  Hi Experts,

  I have an AP 3702 which loses connectivity to the WLC and line protocol goes down.

  PoE is always present on the connection to the switch, but only to 15.4 instead of the full 16.8 as with normal operation 3702.

  There are 8 other 3702 AP this floor who have no problem.

  "Could arp not the ip address of the controller, try again later" is a common phenomenon in their newspapers so I don't think it has any bearing on the issue with this particular access point.

  All 9 x 3702 are connected to a switch of edge double accommodation 3750 X battery via 3 x 3560CX in the ceilings.

  If I close and (after some time) put to the port of the switch, the AP will get back in touch with the WLC, but then drop again as before in an hour or two.

  I deleted the config on the AP and let it sit in mode monitor/sniffer for a few days and he stayed until perfectly so I thought everything was ok. I've reconfigured to accept clients, and since then, it has dropped again.

  Hope that this is not a hardware failure and your advice is really appreciated.

  Thank you

  Stem

  *Jul 22 05:14:49.539: %DPAA-3-ERROR: ! MINOR FM-MAC Error No Device;  Read wrong data (0xffff): phyAddr 0x0, reg 0x-Traceback= 119B108z 26FFF24z 26FFA8Cz 26C1870z 15090ECz 150B3C8z 150AC30z 15065C4z 12250DCz 122CF08z 132B150z 1310*Jul 22 05:14:50.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up*Jul 22 05:14:50.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down*Jul 22 05:14:52.539: %LINK-6-UPDOWN: Interface BVI1, changed state to down*Jul 22 05:14:53.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down*Jul 22 05:14:54.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up*Jul 22 05:14:59.099: %LINK-6-UPDOWN: Interface BVI1, changed state to up*Jul 22 05:14:59.539: %DPAA-3-ERROR: ! MINOR FM-MAC Error No Device;  Read wrong data (0xffff): phyAddr 0x0, reg 0x-Traceback= 119B108z 26FFF24z 26FFA8Cz 26C1870z 15090ECz 150B3C8z 150AC30z 15065C4z 12250DCz 122CF08z 132B150z 1310*Jul 22 05:15:00.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up*Jul 22 05:15:00.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down*Jul 22 05:15:02.539: %LINK-6-UPDOWN: Interface BVI1, changed state to down

  Messages above give me the feeling that there is a problem with communication between the physical network of the access point connection and control software. This can be hardware and associated software. Your best bet to analyze tracing messages is TAC, so my advice is to connect a case and let send them your registration. The 3700's have "limited lifetime warranty" so you can ask a new in case it is broken (even without a smartnet) you have to wait at least 10 days. Keep us informed about the solution! Please rate helpful messages... :-)

• The 1310 AP configuration and IOS

  I have two 1310's

  the info for A is:

  Product/model number:	AIR-BR1310G-A-K9-r
  Software system Filename:	C1310-k9w7 - tar.124 - 3 g .JA1
  System software version:	12.4(3G) JA1
  The boot loader version:	JA4 12.3 (2)

  the infor for B is:

  Product/model number:	AIR-BR1310G-A-K9
  Software system Filename:	C1310-k9w7 - tar.124 - 3 g .JA1
  System software version:	12.4(3G) JA1
  The boot loader version:	JA4 12.3 (2)

  I'm trying to create a bridge root bridge of relationship and I'm out of luck.

  they are on my desk in front of them, I tried different cisco configs and radio, keep going down.

  I tried express setup (where it requires an SSID) and a manual configuration (where the SSID is not required since I DO NOT NEED to a SSID for a simple communication from gateway to gateway).

  ex: http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml

  These two will link two buildings and each will have a switch on the other end.

  simple enough no VLAN etc.

  I begin to suspect the IOS versions that I can't find these versions of IOS in all documentation I looked for examples of configuration.

  This AP is very popular for use in severe environments as an AP not a bridge also to some bridges, you can use an omni antenna if the 1310 is the root for a mutiple no roots or the builtin antenna may not meet remotely you need and you can use a Yagi or dish for the link.

  If you use a single antenna, you will have to change it in the config you use right/primary only antenna. If you do not do this, try using the left/secondary antenna AP and the connection will fail because of the lack of an antenna, your other choice is to put an antenna on both connectors and not worry.

  There isn't that one radio, based on the communication software will pass the exit to the righht or left antenna if diversity is enabled

  the builtin antenna is vertically polarized so you shoud in stall the Yagi with vertical polarzation is polarization normal if you follow the antenna installation instructions. There is normally an arrow and the word to indicate the orientation of the antenna.

  Each AP may be at the root, don't forget to ecre evidence all coaxial connections.

  Yes, you learned that the tree covering weight works.

  Good luck

  Bill

• 'Restart now' IOS command for 1310 Wireless Bridge

  I have 2 Setup bridges wireless Cisco Aironet 1310, the line-of-sight, 3/4 mile, one as Root as Non-Root.  Sometimes they drop their connection, but a hard reboot, one or two bridges will re-establish the connection.  What is the equivalent IOS command to the

  "GUI > system software > System Configuration > reboot now" command?  I would like to be able to telnet to the units and issue/script, the appropriate command.

  the command is "recharge".

  BRIDGE # reload

  Concerning

  Surendra

• Can I connect SFP GLC-LH-SMD connector lc single fiber on Cisco 897VA Module?

  Hi all

  Please can I connect SFP GLC-LH-SMD connector lc single fiber on Cisco 897VA Module?

  Thanks in advance.

  If you have only a single glass fiber then the GLC-LH-SMD = is NOT good

  because it is for double connection to a pair of fiber.

  You would like more information by your ISP, you will most likely need a GLC-BX-D (RX-TX/1310 nm, 1490 nm) or a GLC-BX-U(1310-nm TX/1490-nm RX)

  See below

  1000Base-BX10-D and 1000BASE-BX10-U SFP for bidirectional single fiber Applications

  SFP 1000BASE-BX-D and 1000BASE-BX-U, compatible with the IEEE 802.3Ah standard 1000BASE-BX10-D and 1000BASE-BX10-U, carried on in a single strand of SMF standard.

  A 1000BASE-BX10-D device is always connected to a device of 1000BASE-BX10-U with one strand of SMF standard with functioning of the chain of transmission, up to 10 km.

  The communication on a single strand of fiber is achieved by separating the wavelength of transmission of both devices, as shown in Figure 2: 1000BASE-BX10-D transmits a channel 1490 nm and receives a signal of 1310 nm, while 1000BASE-BX10-U transmits at 1310 nm wavelength and a signal of 1490 nm. As shown, the presence of a separator of multiplexing (WDM) length of wave-division integrated with SFP to split the 1310 nm, 1490 nm light railways.

  Figure 4.      Two-way transmission of a single strand of SMF

  

  GLC-BX-D and SFP GLC-BX-U supports also digital Optics (DOM) of the functions of surveillance in accordance with approval of the standard of the industry (MSA) multisource SFF-8472. This feature gives the end user the ability to analyze parameters in real time of the FPS, such as the optical output power, optical input power, temperature, laser bias current and transceiver supply voltage.

• Refuse the TCP (no relation) dan disassembly TCP connection ON ASA 5510, HELP Please

  IM currently implemented with AIP-SSM-10 ASA 5510 IPS and I have problem with ASA, with IPS feature currently disabled, I keep received complain blocked/idle the connection to the oracle server, using port 8000 host remote-office, I traced with syslog and message received from large number associated with the oracle server IP address.

  the network diagram is a bit like this:

  ________ ________ _____________

  | Oracle | switch | ASA 5510 |

  | Server | | ___ |---| transparent |

  -------- -------------

  192.168.10.206 |

  |

  |

  -------------

  | ROUTER |

  |___________|

  |

  ________ -------------

  | DISTANCE | ------ | Router |

  | THE USER | -------------

  ----------

  192.168.5.x

  and the syslog message looks like:

  302013: built inbound connection TCP 1662347 for OUTSIDE:192.168.5.52/1311 (192.168.5.52/1311) inside:192.168.10.206/8000 (192.168.10.206/8000)

  302014: disassembly of the TCP connection 1662345 for OUTSIDE:192.168.5.52/1310 for inside:192.168.10.206/8000 duration 0: 00:00 542 bytes TCP fins

  302013: built inbound connection TCP 1662345 for OUTSIDE:192.168.5.52/1310 (192.168.5.52/1310) inside:192.168.10.206/8000 (192.168.10.206/8000)

  302014: disassembly of the TCP connection 1662343 for OUTSIDE:192.168.5.52/1309 for inside:192.168.10.206/8000 duration 0: 00:00 539 bytes TCP fins

  302013: built inbound connection TCP 1662343 for OUTSIDE:192.168.5.52/1309 (192.168.5.52/1309) inside:192.168.10.206/8000 (192.168.10.206/8000)

  106015: deny TCP 192.168.5.52/1302 to 192.168.10.206/8000 flags ACK END on the OUTSIDE interface (no link)

  302014: disassembly of the TCP connection 1662338 for OUTSIDE:192.168.5.52/1308 for inside:192.168.10.206/8000 duration 0: 00:00 538 bytes TCP fins

  106015: deny TCP 192.168.5.52/1301 to 192.168.10.206/8000 flags ACK END on the OUTSIDE interface (no link)

  106015: deny TCP 192.168.5.52/1298 to 192.168.10.206/8000 flags ACK END on the OUTSIDE interface (no link)

  106015: deny TCP 192.168.5.52/1303 to 192.168.10.206/8000 flags ACK END on the OUTSIDE interface (no link)

  can someone help me, I'm completely stuck on this problem to cause...

  Thank you.

  7.1 (2), which contains the fix for it, is already posted at http://www.cisco.com/cgi-bin/tablebuild.pl/pix.

  If the workaround works for you, however, and you don't touch any other problems, then I would probably recommend you just stay on this version, but I'll leave it up to you.

• 1310 aPs are UP but do not associate

  My goal is to fill the two LANs buildings with an installation simple bridge safe.

  I have two 1310 with antennas internal facving each other on a desk.

  They boith have their status as UP but do not associate.

  also do not know how to secure the signal, I don't need the clients that connect.

  Here are the two HS runs:

  Current configuration: 1076 bytes

  !

  version 12.4

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  name of host-DATAC1

  !

  enable secret 5 $1$ ng6O$ FKqQV5YWA7Rn/INPTUrVV0

  !

  No aaa new-model

  !

  !

  !

  dot11 ssid

  open authentication

  !

  !

  !

  username wadmin password 7 110A181520131B0937

  !

  Bridge IRB

  !

  !

  interface Dot11Radio0

  IP 172.16.3.121 255.255.248.0

  no ip route cache

  !

  SSID

  !

  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0 Basic6.0 basic - basic-12 9.0, basic 0-18, 0

  Basic-24, 0 basic-36, 0 48 basic, basic 0-54, 0

  station-role root bridge

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface FastEthernet0

  no ip address

  no ip route cache

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface BVI1

  IP 172.16.3.120 255.255.248.0

  no ip route cache

  !

  IP http server

  no ip http secure server

  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

  Bridge 1 priority 9000

  Bridge Protocol ieee 1

  1 channel ip bridge

  !

  !

  !

  Line con 0

  line vty 0 4

  local connection

  !

  end

  ===============

  Current configuration: 1058 bytes

  !

  version 12.4

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  name of host-DATAC2

  !

  enable secret 5 $1$ $6Ozr qpIB50uHfJWlv/zw9Iocj1

  !

  No aaa new-model

  !

  !

  !

  dot11 ssid

  open authentication

  !

  dot11-network map

  !

  !

  username secret wadmin 5 $1$G/7u$loT2nfYJ7/tBZi7.i.S4o0

  !

  Bridge IRB

  !

  !

  interface Dot11Radio0

  IP 172.16.3.124 255.255.248.0

  no ip route cache

  !

  SSID

  !

  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0 Basic6.0 basic - basic-12 9.0, basic 0-18, 0

  Basic-24, 0 basic-36, 0 48 basic, basic 0-54, 0

  station-role root bridge

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface FastEthernet0

  no ip address

  no ip route cache

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface BVI1

  IP 172.16.3.123 255.255.248.0

  no ip route cache

  !

  IP http server

  no ip http secure server

  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

  1 channel ip bridge

  !

  !

  !

  Line con 0

  line vty 0 4

  local connection

  !

  end

  Well Yes, here is the problem that I see!

  Find the two roles are ROOT BRIDGE!

  BR-DATAC2

  =============

  interface Dot11Radio0

  IP 172.16.3.124 255.255.248.0

  no ip route cache

  !

  SSID BR

  !

  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0 Basic6.0 basic - basic-12 9.0, basic 0-18 basic 0-24 0 basic-36, 0 48 basic, basic 0-54, 0

  station-role root bridge

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  also on BR-DATAC1

  ================

  interface Dot11Radio0

  IP 172.16.3.121 255.255.248.0

  no ip route cache

  !

  SSID BR

  !

  Speed basic - 1.0 2.0 - basic basic - basic-11 5.5, 0 Basic6.0 basic - basic-12 9.0, basic 0-18 basic 0-24 0 basic-36, 0 48 basic, basic 0-54, 0

  station-role root bridge

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  Here's the change we need to do

  Delete the IP address under dot11 radio interface and then on one that is not connected to a switch and under the number of interface radio 'station role non-root bridge', this will help you!

  Concerning

  Surendra

• Problems with AP 1310

  Hello world...

  I am configuring a standalone AP AIR-LAP1310G-A-K9R.

  I have download the IOS LWAPP firmware downgrade software, I installed the firmware c1310-k9w7 - tar.123 - 11.JA4 and I am trying to configure the AP.

  Using the default configuration I plugged the AP to my network and this AP had IP and I could get access to the Web Page.

  The problem I got is the following:

  I configured a SSID without VLAN and with my laptop using WirelessNetView, I could see the transmission power in this SSID.

  In a normal configuration without external antenna (turn OFF), I got about 80 dB.  I know it's very low emission power because I have the AP in the same office.  Test different configuration, I had almost the same value (-75->-80).   Audit I plugged the external antenna and I got about 30 dB.

  My question is: I'm setting disabling the external antenna, but connecting the antenna I had good power.  Is there a question about it?

  Is the version of the firmware of the question?

  What should I do to get the maximum power using the internal antenna.

  Thanks in advance...

  Guillermo Gonzalez.

  Guillermo,

  There are 2 different 1310 models Bridge with antenna internal (without antenna connectors!) and on the other without the antenna conectors, which is only 1310 that you can connect an external antenna. I guess this is the model that you have, because you can connect to the antenna. By accessing the configuration of radio on the Web Interface, you will find the external antenna option (enable / disable) but it won't change anything on the device configuration or behavior. It is basically a tag that you can use when you manage trough of devices, say a WLSE, so here you will see a map of your site and it will tell you if you have internal or external antennas... But as I said, it of just "informative" and will not do anything to the unit itself.

  If your 1310 has a conector antenna, you MUST use an external antenna, otherwise, it will be to distribute the signal but you will get a connection very very low.

• Cannot print/connection of Windows 7 for shared PSC 1315 on the XP Machine

  I have a HP PSC 1315, connected to a computer running Windows XP (32 bit).  This printer is shared.  I can access it from other XP machines on my home network.  I can't access it from my computer Windows 7 (64-bit).  I can see the printer is shared on the computer, but when I double click on it, I get the following error:

  "Windows can't find a driver for hp PSC 1310 series on the network."  To locate one manually, click on OK.  Otherwise, click Cancel and consult your network administrator or the printer manufacturer's Web site. »

  Then I tried to download the driver Windows 7 (64 bit) of HP and installed on my Windows 7 machine:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-75052-1&LC=en&DLC=en&cc=CA&...

  At the end of the installation, it asks to connect the printer to the computer via USB.  Because I'm not physically the printer connected to the Windows 7 computer, I check the box that says I can't login now and go forward at the end.

  Then I tried to connect to the printer and I get the same error.  I try to locate a driver manually.  I point to c:\windows\inf\ without success (I am * if * the driver info might settle there, but I don't know what the name of .inf).  Windows says that it cannot find an appropriate driver.  Maybe I should be looking elsewhere?

  I found some troubleshooters on the HP website, but it does not give "shared printer on a network" as one of the schemes to solve connection problems.

  I'm a little confused on this one.  Hoping that there will be something simple, I missed.

  Thank you!

  Hello

  Kahless wrote:

  I have a HP PSC 1315, connected to a computer running Windows XP (32 bit).  This printer is shared.  I can access it from other XP machines on my home network.  I can't access it from my computer Windows 7 (64-bit).  I can see the printer is shared on the computer, but when I double click on it, I get the following error:

  "Windows can't find a driver for hp PSC 1310 series on the network."  To locate one manually, click on OK.  Otherwise, click Cancel and consult your network administrator or the printer manufacturer's Web site. »

  Then I tried to download the driver Windows 7 (64 bit) of HP and installed on my Windows 7 machine:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-75052-1&LC=en&DLC=en&cc=CA&OS=4063&product=374568&sw_lang=

  At the end of the installation, it asks to connect the printer to the computer via USB.  Because I'm not physically the printer connected to the Windows 7 computer, I check the box that says I can't login now and go forward at the end.

  Then I tried to connect to the printer and I get the same error.  I try to locate a driver manually.  I point to c:\windows\inf\ without success (I am * if * the driver info might settle there, but I don't know what the name of .inf).  Windows says that it cannot find an appropriate driver.  Maybe I should be looking elsewhere?

  I found some troubleshooters on the HP website, but it does not give "shared printer on a network" as one of the schemes to solve connection problems.

  I'm a little confused on this one.  Hoping that there will be something simple, I missed.

  Thank you!

  Here's a good explanation of how to share a printer from an XP PC to Windows 7 PC on a network home.  It should work since Windows 7 (64-bit) PC can see the partition Windows XP 32-bit.  What you missed was the type of port to use for the network connection.

  Best regards
  ERICO