Connection to multiple devices sequence using FF Fieldbus Foundation open VFD

Similar Questions

• HDMI connections to multiple devices

  I have a Sony Bravia 46EX640 and a HD DVR with an Xbox. I am planning to buy a Sony BDVN790W surround sound system. I'm trying to minimize the number of connections, and I would only use the hdmi connections. I am familiar with ARC and this specific TV unfortunately does not have this feature, but I have the following wires in mind. My goal is to get the highest quality of image and sound and minimizing connections to make it possible. My diagram of wiring in mind:

  OUT of Xbox HDMI--> HDMI BDVN IN
  DVR HD--> BDVN HDMI HDMI OUTPUT TO
  BDVN HDMI OUTPUT--> TV HDMI IN

  The only hole I see is the sound of the tv because it is not equipped with BOW and HDMI does not work for her, correct? Do I have TO use the digital audio output to the audio quality on the TV for sound? My ultimate plan is to use the HDMI connections. Is there any other possible wire using only HDMI cables?

  This configuration will give you audio from your VCR digital HD, XBOX and BLU RAY
  through your speakers BDVN790W and HD video to your TV.
  If you also use your TV as a tuner for over-the-air channels, then you will need to use the optical cable from TV to the BDVN790W.
  If you do not use your TV as a tuner then connect you mentioned won't work.

• best practices for the structure of the code control multiple devices in a sequence-step 2

  I have a question about code architecture and to get multiple devices controlled and synchronized for an experience. It is an 'architecture' - type application, so I hope for some suggestions on how to proceed.

  I run an experience in which I order 2 NI PCI-6733. I will soon add a Tektronix AFG 3022 B and have long been turned off the opportunity to rewrite my code labview from the ground upward. I inherited from a previous search, and although functional, I want to make it easier to modify and divide into sub - VI and these. Link to the current program (labview 8.6.1) is here if you do not want to see the code that is currently used and Subvi is in a zip file. The current version of experience consists of one stage, all writing the data for PCI cards is saved for the end. I need to change that in my configuration again well.

  The new experience consists of 2 steps. The first will take place (loop an array of output for PCI cards) until he heard a 'real' another computer (connected via TCP). When you do that, it should go to step 2 and run a sequence (usually 10 ^ 5 timeunits of length, where the unit of time is 0.1 ms) which refers to two PCI, the AFG 3022 B cards and with the flexibility to add more devices in the future.

  The most popular would be structural advice. How to organize the screw, if it's good to use a VI 'master' that would control the two sub - VI phase 1 and 2, etc...  Feel free to ask for more details if it helps clarify my question. Thank you!

  Such programs typically use a kind of State machine.  You will find many tutorials on LabVIEW state machines in these forums or forums of LAVA.  If you do a rewrite, I also recommend that consider you the LabVIEW classes.  They help modularize your code and do more reusable subparts.  You can end up with less to maintain, accordingly.

  You can also consider TestStand.  It was designed to perform sequences of tests, so can make your life easier.  It would be also exaggerated gross.

  Let us know if you encounter any problems with the machinery of State or classes.

• E3000 loser on multiple devices wireless connectivity

  Problem with router Linksys E3000 (firmware 1.0.02). I have problems with the following wireless connections:

  iPhone 4G (female)

  iPod Touch 2 G

  PC with Wi - Fi (adapter brand Linksys no)

  NetBook Acer (not Linksys adapter brand)

  It comes from the connection is interrupted and dropped, but the devices and the router DHCP clients table indicate that connections are always present. By interruption, I mean that no data traffic is transmitted.

  IPhone 4 G to the my iPod Touch Wi - Fi my son and wife show that they are connected to the network home, with WiFi bars displayed, and the check mark is present next to the home network connection in the device for both settings. When I check the table of DHCP E3000 customers, two Apple devices are listed as with a connection. Yet the two devices to display network errors when you try to use any application that connects to the internet. By raising the wifi on each connection, the connection is restored to the point where traffic passes now. My wife and son believe it's after 10 minutes they encounter interruptions.

  On the PC and NetBook, connections must be terminated and reconnected. I've not timed to see how long before the connection becomes problematic.

  Interestingly, my ASUS laptop and my iPhone 4G do not have the issue, nor did my (Dell) laptop.

  There is no time-out setting in the router config. Thing the closest is the beacon interval, but I don't know which way to adjust (up or down) to help the devices which are undergoing interruptions. I did not a setting of the interval... at this moment, everything is set to the default settings.

  The E3000 replaced an old WRT54 (v2 hardware) router so that I could have a N router in the House.

  Thank you
  -Phil

  How about you change wireless channel? If you do not, then you should try it. Using the two bands, 2.4 Ghz and 5 GHz? If so, make sure they have different but unique SSID. Have you tried to remove the Security Wireless for testing?

• Push the connection interrupted by device - using eclipse of the bb Simulator

  Using BlackBerry plugin for Eclipse

  For OS 6

  After taking two weeks to try and correct an error "not close until you have finished" simple with SQLite, I now have a bit of a configuration issue with the Eclipse software.

  When I push a message to the Simulator, I get the following error.

  <2012-04-18 15:39:15.471 EDT>:[378]:::http://172.17.111.35:[email protected]&priority=2&besurl=192.168.1... pushId = -62be8811:136c6f71d73:-7ff576188, destination = [email protected], result code = 400 net.rim.protocol.iplayer.push.b: Push connection aborted by device>
  

  According to the knowledge base, a 400 error is 'invalid Push to the format.

  Mobile data service 3.7 and earlier versions: the email address or the personal identification number (PIN) used in the Push was not recognized as a user of BlackBerry Enterprise Server enabled for Mobile Data Service. »

  I'm sure it's something with the configuration in the rim.property file.  Something probably must be on or off, I can't understand.

  [MonitorAgent]
  MonitorAgent.listen.port=8070
  
  [WebServer]
  WebServer.Tomcat.transcoding= false
  WebServer.listen.host=localhost
  WebServer.listen.port=8080
  WebServer.listen.sslport=8443
  WebServer.servlet.monitor.port=8070
  WebServer.servlet.monitor.host=localhost
  WebServer.servlet.push.port=81
  WebServer.servlet.push.host=localhost
  WebServer.servlet.push.ssl=false
  
  [SRP]
  SRP.UID= please get one
  SRP.AuthenticationString= Please get one
  SRP.InetAddress= Please get one
  SRP.Port=3101
  SRP.logging=true
  
  [IPPP]
  IPPP.push.listen.tcp.port=81
  IPPP.connection.MaxNumberOfKBytesToSend=128
  IPPP.queue.flowcontrol.window.size=-1
  IPPP.queue.flowcontrol.timeout=600000
  IPPP.logging=true
  
  [UDP]
  UDP.receive.port=19781
  UDP.send.default=19780
  UDP.init=initialization_packet
  UDP.logging=true
  
  [HTTP HANDLER]
  application.handler.http.logging = true
  application.handler.http.CookieSupport = true
  application.handler.http.AuthenticationSupport = true
  application.handler.http.AuthenticationTimeout = 3600000
  application.handler.http.device.connection.timeout = 140000
  application.handler.http.server.connection.timeout = 150000
  application.handler.http.device.credentialTimeout = 60000
  application.handler.http.authentication.mechName2oid = Negotiate=1.2.840.113554.1.2.2, NTLM=1.3.6.1.4.1.311.2.2.10, Basic=1.3.6.1.4.1.88888.1.2
  
  [Security]
  net.rim.security.auth.DefaultDomain = rim.net
  
  [HTTPS HANDLER]
  application.handler.https.allowUntrustedServer = false
  application.handler.https.logging = true
  
  [TLS HANDLER]
  application.handler.tls.allowUntrustedServer = false
  application.handler.tls.logging = true
  
  [OCSP HANDLER]
  application.handler.ocsp.StatusProviders = net.rim.protocol.iplayer.connection.handler.device.ocsp.OCSPProvider
  application.handler.StatusProviders.OCSP.PrimaryResponderRank   = Default
  application.handler.StatusProviders.OCSP.Responder.Default      = http://dhobbs-wnt.rim.net/ocsp
  application.handler.StatusProviders.OCSP.UseDeviceResponders    = yes
  application.handler.StatusProviders.OCSP.UseCertResponders      = yes
  application.handler.ocsp.DebugLogging = no
  
  [LDAP HANDLER]
  application.handler.ldap.DEFAULT_SERVER = dhobbs-wnt
  application.handler.ldap.DEFAULT_PORT   = 389
  application.handler.ldap.DEFAULT_QUERY  = ou=people, o=rim.net
  application.handler.ldap.DEFAULT_LIMIT  = 20
  application.handler.ldap.COMPRESSION    = true
  application.handler.ldap.logging        = false
  
  [Database]
  Database.shouldConnect=false
  BESName=DAISY1
  Database.Driver=sun.jdbc.odbc.JdbcOdbcDriver
  Database.URL=jdbc:odbc:BESMgmt
  Database.DBCycleTimer=5
  
  [ACL]
  ACL.Authorization.Datastore=net.rim.shared.service.authorization.JDBCAuthorizationDatastore
  ACL.Enabled=false
  
  [ESS]
  ESS.helpfile    = help/Using_the_Email_Server_Simulator.html
  ESS.launcher    = bin/launcher.exe
  
  [Email]
  Email.deviceId      =2100000A
  Email.pop3Server    =pop3.server
  Email.smtpServer    =smtp.server
  Email.personal      =Dean Logan
  Email.address       [email protected]
  Email.smtpPort      =25
  Email.pop3Port      =110
  

  Any suggestions?

  Figured it out.

  When you set the port of the unit, I had the wrong port

  _notify = (StreamConnectionNotifier) Connector.open (appAttributes.devicePort + appAttributes.deviceSide);

  My company uses a Test port and a port of Prod, so that we can have 2 versions of the application on the device at the same time.  Then, chaning the listening port of 1315 to 1313 authorized service push push to the appropriate port and the app was able to read the data.

• I use lightroom on my laptop, and now I want to download on my desktop that I have multiple devices to the original purchase.  How can I download it for my office?

  I use lightroom on my laptop, and now I want to download on my desktop that I have multiple devices to the original purchase.  How can I download it for my office?

  You install programs exactly in the same way you did the 1st time... Put your disc in the drive, and enter your serial number when asked

  .

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a way to go to a page to download the Adobe programs if you do not have a disk or drive

  -you will need to enter your original serial number during the installation for non-Cloud programs

  -Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html

  -Cloud Getting Started https://helpx.adobe.com/creative-cloud.html

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• I am a student with a desktop computer and a laptop - can I use a license student on multiple devices.

  I am a student with a desktop computer and a laptop - can I use a license student creative cloud / log on multiple devices.

  Hi,

  CC Adobe license can be activated on 2 machines using the same Adobe ID.

  Reference: licenses and terms of use | Adobe

  Kind regards

  Sheena

• How to enable the use of multiple devices of cuda in Adobe AE?

  I had nvidia gtx 690 and nvidia gtx 760. They were both considered by the pilot 340.52 and we tick "use multiple GPU devices." Adobe AE CC 2014 so rendered was recognizing and using the two GPU devices. Then I replaced the gtx 690 with gtx 780Ti as a primary device. The driver does not have the option to use multiple devices and gpu in the AE preferences only the ti 780 is displayed.   When the don't return that this graphic card works. My question is how to use ti 760 & 780 two GPU in the rendering, as was the case with gtx 760 & 690?

  Thanks a lot for your help.

  Read the paragraph that begins with "If you have several installed GPU, GPU acceleration traced the beam 3D renderer will use the CUDA cores on each of them, as long as they are of the same level of CUDA computation" here:

  Features GPU (CUDA, OpenGL) in After Effects

• How to synchronize multiple devices (294 x) Rio usrp

  Hello

  I'm trying to receive 4 channels using two devices USRP-294xR (USRP RIO) to synchronously and run the example for the reception of several device program.   Often, I receive the error message "failed synchronization.  If I run the example several times in a row, this error message occurs more often than otherwise, but for all the times that he does not, I am able to collect data that seems like synchronous through the channels of reception.  So, in a way that works for me, but with the annoying feature that I need to run the program several times now until I am able to avoid the "Synchronization failed" error

  My installation includes an Octoclock connected to the Ref connections in and PPS in the two USRPs.  In the example, VI, I selected Ref in, but it is clear to me what choice should I use for relaxation.  Possible options are: 'Software', 'Immédiate', "Digital Edge", "Rx Start Trigger" and "Tx Start Trigger.  I had assumed my previous experience using these devices with the FPGA Ettus I would choose an option indicating that I tried to synchronize the external signal of PPS.  "External PPS" is not among the options of trigger, I'm confused as to how the synchronization.

  I saw the article below, but it's not not clear for me if I should be able to achieve my goal without making changes FPGA. It is possible to synchronize multiple devices using the program by default FPGA and example (i.e., for example RIO, not the host screw using the Ettus FPGA image)?  If so, any suggestions to help me avoid this error "synchronization failed"?

  http://zone.NI.com/reference/en-XX/help/373380D-01/usrphelp/synchronization/

  Thank you.

  Rob

  rkossler1 wrote:

  Since we did not have a 6674 t, I thought I might as well try to connect PPS from a RIO USRP to PPS on the two RIOs USRP.  I just used a BNC - T to "distribute" the relaxation.  It did not work - maybe for the same reason you mentioned on the PPS USRP out is not strong enough for the Octoclock by car.

  Yep, that's exactly it. The USRP RIO is not output enough power on the PPS TRIG OUT line to drive the lines of PPS TRIG IN two USRP RIOs, unfortunately

  rkossler1 wrote:

  How can I know which USRP RIO is the 'master '?  Do I need to designate in the software?  I chose arbitrarily use the device for which I have connected the PPS on the BNC - t 'RIO0', but I don't know how the SW knows what USRP I chose to connect the power cord to.

  The USRP captain's exit a PPS TRIG OUT in PPS TRIG IN sound. then all the USRPs you set this unit as the * first * device in the table of features of RIO for the façade of synchronization with a cross screw.

• 3070 connectivity problem - multiple Accespoints with the same SSID

  Hi all

  I have a problem with my printer HP Deskjet 3070 printer all-in-one.

  I have 2 accespoints with the same SSID for better coverage of the pit of the wireless home network.

  For some reason any my HP printer keeps losing wireless connection when the 2 accespoints are rising.

  I use a different frequency for the 2 accespoints channel and it works fine with all other wireless devices.

  I did that a DHCP are used, r, but in fact it doesn't matter because the printer uses a static IP (192.168.0.3)

  When the two AP is the printer loses wirelesss connectivity. (The blue led will blink)

  If I take one of the accespoints offline, the printer becomes available.

  Is this a problem on my end or a problem of software/firmware printer?

  Kind regards

  -eth0

  Lol this is not very clear to me?

  But it is very good that we continue here:

  http://h30499.www3.HP.com/T5/printers-DeskJet/3070A-connectivity-issue-multiple-Accespoints-with-the-same-SSID/TD-p/5865699#.UKNyiYatlI1

• Windows 7 network can't see multiple devices on the network

  Hi all.  I'm about to leave my hair on this issue - I hope someone can prevent the horror that would be me without hair.

  I am running Windows 7 Home Edition on a personal computer that is connected via cable to a router UVerse also providing my home with wireless services.

  A few months ago, I could see - of my PC, network and devices and printers - the two PS3, XBox systems and Samsung TV devices that are connected to my wireless network.  Apparently randomly, my computer has ceased to be able to see these devices.  After trying everything I could think of, I've finally reformatted the system (before Christmas) and everything was good again until last week when my computer stopped once more to see these devices.  I * really * don't want to reformat my system again...

  Here are some details on where I started after the last reformat:

  The PC is connected to a homegroup.

  The PC has a wired connection to the router.  The devices are connected over wireless.

  The firewall is turned on.

  AVG anti-virus has been activated.

  Network discovery, file and sharing printers and streaming media are all enabled.

  Password sharing is disabled.

  Devices could stream Netflix/Hulu as well as files on my computer (using the PlayOn Server - I've never used WMP).

  Now my devices can still Streaming Netflix/Hulu, but not the files on my computer.  The PC can't see the devices and the devices cannot see the PC.

  Here is a list of most of the things I've tried to solve (although I've done so many things, I probably don't forget some):

  I added the PC to the wireless network, so now that it is connected both cables and wireless.  I even tried to fill these connections, although I removed the bridge when I saw that there was no difference.

  I have disabled the firewall completely.

  I disabled the AV entirely.

  I switched a residential group to a working network and vice versa.

  I gave you the assigned IPs devices in the router configuration.

  I've rolled back all the windows updates installed since the last time the devices showed in the PC network.

  I've removed the devices on the network, reconnected the and reconfigured to ensure that they have the media streaming (if applicable).

  I did several reboots the PC, the router, and devices.

  I added the PlayStation Network and XBOX Live and applications hosted under NAT/game on my router.

  I have enabled file sharing for devices that use 40 encryption or 56-bit.

  Additional troubleshooting information:

  When I try to add a device using the Add Device dialog box, no device never shows.

  Under media streaming options, when I look at instruments under all the networks and Local network, no unknown device only shows (even in WMP).  All devices that * show are already set to 'allow '.

  If I have access to my router configuration, the devices will appear as connected.

  I can ping devices from the PC.

  I searched endlessly on the Internet (including other threads on this forum) and have tried all of the suggestions I thought.  The only thing I can't do is activate uPNP on my router because routers Uverse do not offer this option.  However, I don't think that it's important because my PC could see these devices for some time after my last reformat and made no changes to the configuration of the router.

  Because multiple and different wireless devices are involved, and because a reformat solves the problem, in my view, it is a Windows problem, but I can't understand what to change on my system to make things work again.

  Anyone have any ideas?

  Hello

  Thanks for posting your query in Microsoft Community.

  It's a shame that you have to format the system first and now, the problem still persists. I really appreciate the efforts made to try to resolve the problem. This can be due to any dispute of third party software due to which the connection failed. I suggest you follow the methods below and check.

  Method 1: Run the network troubleshooter to diagnose the problem.

  Run the network troubleshooter

  Method 2: start the computer in safe mode with network and then perform the clean boot.

  Step 1: restart the computer in safe mode with network and check if the problem occurs, proceed as in the link:

  See: , start your computer in safe mode

  Step 2: If the safe mode with network works, perform clean boot and check if any third-party application is causing problem.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Method 3: To enable the network devices to display on the network map, they must meet four requirements:

  • Must be a HOME network or work: Mapping network only display the devices connected to a HOME network or WORK location. Devices connected to a network PUBLIC or FIELD cannot be displayed using the network card.
  • Devices must be DETECTABLE: The network discovery setting allows devices to be able to be seen by other devices on the same network. For more information, please consult: , enable or disable network discovery
  • Devices must comply with the LINK LAYER TOPOLOGY DISCOVERY Protocol: Topology Discovery LLTD (Link Layer) is a protocol developed by Microsoft to enable networked devices to 'discover' each other. If a device does not use the LLTD protocol so it can not be displayed in the network map. Windows 7 computers have the LLTD protocol implemented.
  • LLTD must be enabled on your LAN connection properties: The Link Layer Topology Discovery Mapper of e/s driver and the Link Layer Topology Discovery responder must be enabled on your local area connections properties panel.

  To check LLTD is enabled, you can refer to the following steps:

  a. Select open network and sharing Center by clicking on the icon of your network down to the right of your task bar:

  b. now, click connect to the Local network

  c. now, click on Properties

  d. ensure that two LLTD options below are selected (by default, these options are still enabled in Windows 7).

  From now to try the methods above and let us know the status. We will be happy to help you further.

• How do I test an application on multiple devices?

  How do I test an application on multiple devices?

  Any information on this?

  Once I created the .ipa file I have to do?

  Creating the API you could use a configuration profile. If it's a development of a distribution one ad hoc, you choose what devices the IPA is allowed to work on.

  So, to make an ad hoc distribution profile that includes all devices on your iPhone Developer account and make the API using this profile. Now, when you did the IPA, you can give it to the people who own these devices.

  If they are all your own devices (or the people that you see every day) you could connect each of them to your Mac and use Xcode window Organizer or peripheral (according to the version of Xcode you are using), and then drag the IPA in the list of Applications for the device.

  If the devices are owned by other people that you do not get to see, you can either send the IPA to them and that they would use iTunes to get it on their device, or if you can put the IPA online you can send a link to them, and they can install the IPA directly from the web page.

  The web server will need to be HTTPS, you cannot use HTTP services from iOS 7.1 is released. To post the IPA online, you can use this utility:

  Mac App Store - BetaBuilder for iOS Apps

• Connect to multiple instances of a script vCenter?

  How can I connect to multiple instances of a script vCenter without going through separate-entry sequences of credentials or credentials on disk storage?

  I need to browse through a table of the vCenters and run scripts against each of them. They are not related, but the same credentials must be valid on all instances.

  It would be great if there was also a way of parallelization of this job such as each returned only thread STDOUT is it speeding up the script.

  All suggestions are welcome, I can see some tips using PowerShell, but I need to do it in Perl.

  Thank you

  Stephen

  You get close, you are missing just a few required modules. Here is the final excerpt that will work for you:

  use strict;
  use warnings;
  use VMware::VILib;
  use VMware::VIRuntime;

  {eval
  My $vim = Vim::login (service_url-online $url, user_name => $username, password-online $password).
  My $vms = $vim-> find_entity_views (view_type-online 'VirtualMachine');
  {foreach(@$VMS)}
  Print $_-> name. "\n";
  }
  };
  Si ($@) {}
  Print $@. "\n";
  }

  Make sure you put things highlighted in bold, it's what you have in your Perl script. I checked on the VMAs, but I'm sure it'll work on Windows as well.

  You're right, the documentation can be better... If one of the reason, VMware has created all these routines support auxiliary, is to abstract the complication of the API. They also assumed that you'd be connectingn to a single host or vCenter simultaneously. All that falls on these basic configs, it will take your own code/etc. and where watching is that the first part of the challenge

  Good luck

• Interruption of the connection to the device

  During the capture of Premiere Pro CS5 with a new cassette containing an original recording, I get a "recorder Error" "Interruption of the connection to the device" of windows. I can resume the capture by clicking Save in the capture window, and it continues with a new file name. For example: 01 3 Clip. AVI continues as 4.avi Clip 01, Clip then 01 4 1, Clip 01 4 2, etc. Has happened 10 times throughout a record of 45 min.

  When I tried to import the clips, it is said that the file is unsupported or damaged. The only one I can use is the last clip in the sequence (Clip 01 4 9.avi). Please let know us what I can do to capture my full video. Thank you.

  Not exactly what the real problem was, but I replace my old cable firewire with a Monster Cable, cable FireLink 300. Email support Adobe also recommended to turn off UAC and the firewall/antivirus. Collectively, the actions seem to have solved the problem I captured 6: 1 hour video with no problems.

• deletion of email/photos from multiple devices

  When I delete a photo or an e-mail message from my Mac, shouldn't they deleted from my iPhone?  I thought that's what iCloud quid... Connect all your devices?

  Pictures YES, but only if using the same Apple ID and with iCloud library lit everywhere.

  The post office Yes, once again, if you use the same accounts, but only if these accounts are IMAP. POP accounts do not have this ability to sync.