connection to the interrupted NAS

Similar Questions

• New router. Connection to the remote NAS device or a file between computers does not.

  I just changed routers and lost my connection wirelessly between devices. Internet is good, but no connection with Lynksys NAS 200 wireless backup. And I can't share files between computers. All my permissions are large open on both computers, but same homegroup does not. Windows 7 on both computers. A desktop connected to the network and a wireless laptop which is connected to the NAS. My wired desktop backup is fine. NA not lose that connection.

  I just changed routers and lost my connection wirelessly between devices. Internet is good, but no connection with Lynksys NAS 200 wireless backup. And I can't share files between computers. All my permissions are large open on both computers, but same homegroup does not. Windows 7 on both computers. A desktop connected to the network and a wireless laptop which is connected to the NAS. My wired desktop backup is fine. NA not lose that connection.

  Me too, I unfortunately have the same problem.

  Installed a replacement wifi router and lost access to a NAS. And it is the only element that would not be re - connect...

  It's the config probably simple setting of the wireless router with the IP Address of the NAS (10.1.10.199 if this is of any help), but it's clearly a mystery to find useful info on how and what to configure...

  Unfortunately, it was easier under XP...

  Thanks for the research.

• Trackpad and keyboard of the interruption of the connection

  Interruption of the connection between the keyboard and the trackpad on the laptop. What should do?

  Try resetting the NVRAM/PRAM http://support.apple.com/kb/ht1379 memory

• Interruption of the WiFi connection.  Green light is the Airport Express. Settings Network said the cable for the Wi - Fi connection is not connected or the device at the other end does not respond.

  Interruption of the WiFi connection.  Green light is the Airport Express.  Settings Network said the cable for the Wi - Fi connection is not connected or the device at the other end does not respond.  Tried to reset Airport Express, but remained light amber or orange flashing.  I unplugged it and waited and plugged back into the light turned green.  Rebooted computer (Mac Pro). Parameters of said the same thing.  Managed to create a WiFi "network with the ethernet in the network settings section, and yet I am wireless.  I am online but not wired and WiFi settings still says not connected, and either the cable for the Wi - Fi is not plugged or the device at the other end does not respond. I don't understand this situation.  My original WiFi name disappeared.  How I am on the internet?

  What is the brand and model of the modem Internet you have the AirPort Express directly connected by Ethernet? What exact model number is your Express?

• E2500: 'the connection to the 192.168.1.1 was interrupted." When you access the configuration page.

  Trying to access the configuration page, 'the connection to the 192.168.1.1 was interrupted."  I'm wired into the router.  Any idea of what is the cause?

  Ugh, I'm stupid... I was using the button in the back instead of the reset button on the bottom.  Thanks for the tip-off that the reset method should have worked.

• Unable to connect to the NAS network via a wired connection?

  Hi all

  I have 2 network NAS. They are both a Bay D-Link ShareCenter 2. One is full of media I use for streaming and the other is used to keep backups of my computers and some software. Both of the NAS are configured in RAID mirror. They both worked fine when I got them almost a year ago, they are mapped to letters pilot Y and Z. 2 days when I logged my office a popup notification came to say.
  "cannot reconnect to all network drives, click here to check the status of your network drives."
  so I checked it status and he said they were offline. I restarted my computer and both the NAS, but it made no difference. Then I tried to disconnect the drives, but when I try to reconnect to them I get this error;
  "Windows cannot access \\192.168.0.32\Volume_1\Joe, check the spelling of the name. Otherwise, there could be a problem with your network. In an attempt to identify and solve network problems, click on diagnose. »
  When I click to diagnose it is unable to find a default.
  The next thing I did was disable my Ethernet card and connect to my network with my WiFi adapter. Then I tried to re - map the NAS is connected via the wireless. This time he allowed me to map them and they seem to work as usual via the wireless connection, but it is rather slow on the wireless.
  Then I disconnected my WiFi connection and reactivated my Ethernet card. When I tried to open the NAS I get this error message;

  "An error occurred while reconnecting Z: to \\192.168.0.32\Volume_1\Joe, Microsoft Windows network: the local device name is already in use." This connection has not been restored. »

  A friend told me that this error was because the drive letter is used by a USB storage device or remembered from a previous session, and to remedy, I should run these 2 commands CMD;
  NET use * / Delete Yes
  NET use / persistent: no
  After you run the two orders, nothing has been changed still the same problem. I also I have no USB storage device so it may be that.
  The next thing I tried was to ping both the NAS, I did this on Ethernet and WiFi connections, and both times I return a normal response both to the NAS.
  I defrosted then to restore an image from my Office I made around a week ago and I know that I don't have this problem at the time. The image I did was with Acronis. When I started on the CD of Acronis support, I discovered that Acronis software could connect both the NAS on my desktop Ethernet. After restoring I still have the same problem.
  Now, there's 1 thing I noticed, my laptop can still connect to both WiFi and Ethernet NAS with all the problems. I also have an android phone, and who can connect both of the NAS via a WiFi connection.
  1 last thing you to know is I can always get to the configuration of the NAS so pages I visit it local address in a web browser. I also ran a factory reset both the NAS and then re-applied my own settings. This does not solve the problem, and more that turning March my routers.
  Please can someone help me solve this problem. I'm running a Windows 8 Pro 64 Bit operating system. If you need more information on my system spec or how I have my setup of home network please let me know.
  Thank you Joe.

  This problem has now been fixed.

  For some reason any my AVG firewall had defrosted on its own to block access to the features as well as to define its self to disable the file and printer sharing of files on the NAS share.
  So a small trick to my firewall and everything works as it should.
  Thank you Joe.

• Flash Player download guard fails with the interruption of the connection and then abandoned.  satellite, Internet connection

  Win XP. Firefox 34.0.5 (latest)

  Continuous Flash Player download fail with the interruption of the connection and then abandons. I'm on a satellite Internet connection.

  It seems to be extremely slow, even when loading the installer which is only 1 MB. Then when I run the Setup and it starts to download the installation there are frequent messages lose the connection and then finally give up.

  I had problems with other software crashes when I'm on a satellite link. This is probably because of the huge latency that can be regarded as a failure of the link. Ping times are usually 800ms but can sometimes be 2000ms!

  Hello

  The installation of fix online program, you use actually download and install Flash Player silently in the background.  If your satellite connection has latency problems, it could cause failure to download.  Please try the published full installer at the bottom of the problems Installation | Flash Player | Windows page, in the section "problems".

  --

  Maria

• interruption of the connection, cannot connect to the server

  I just bought Photoshop Touch for my Tablet Galaxy Note 8. I signed up for Creative Cloud by using an old I connect by an ereader, it still worked, just asked me for my date of birth. I opened creative cloud and as he suggests, dragged an image (jpg) in the screen that appears, and the use of the data went from zero. I then went to the tablet in Creative cloud he has signed with the same login name, then went to settings sync - sync files 'on', only the synchronization with wifi; and he said: "the synchronization process complete", tier 0% complete - which seems to be wrong as it is supposed to be a file there. Then I go to "new" and choose Creative cloud - it works a few boxes around and comes up with "interruption of the connection, cannot connect to the server.

  I tried signing off CC on the mac first, stop the application on the Tablet, but it's solid. It goes without saying that the wifi is on and working on the tablet. Can anyone help please.

  You have the latest version of PS Touch (1.5) installed? If this isn't the case, please try this version. Thanks, Guido

• Interruption of the connection to the device

  During the capture of Premiere Pro CS5 with a new cassette containing an original recording, I get a "recorder Error" "Interruption of the connection to the device" of windows. I can resume the capture by clicking Save in the capture window, and it continues with a new file name. For example: 01 3 Clip. AVI continues as 4.avi Clip 01, Clip then 01 4 1, Clip 01 4 2, etc. Has happened 10 times throughout a record of 45 min.

  When I tried to import the clips, it is said that the file is unsupported or damaged. The only one I can use is the last clip in the sequence (Clip 01 4 9.avi). Please let know us what I can do to capture my full video. Thank you.

  Not exactly what the real problem was, but I replace my old cable firewire with a Monster Cable, cable FireLink 300. Email support Adobe also recommended to turn off UAC and the firewall/antivirus. Collectively, the actions seem to have solved the problem I captured 6: 1 hour video with no problems.

• Wan interrupts the connection after the firmware update

  Looks like the latest firmware upgrade is the source of the problems.

  I've just updated my timecapsule 1 TB of first generation version 7.6.7 and my 3 TB timecapsule new version 7.7.7

  Both are connected to the router of the provider of Internet services and extend the network even in my house.

  WiFi is stable until the upgrade, but now the connection is lost every few minutes or seconds.

  Both versions are later to the respective timecapsules.

  I end up having to downgrade if no solution is found.

  I powered the two market still nothing does not. Redefine the network and tried both hidden and not hidden, yet once nothing doesn't.

  Any ideas on what is causing the problem?

  Well, since nobody seems to have an explanation, and Apple are not out with firmware update after 7.7.7 and 7.6.7 I decided to downgrade the firmware to the previous version. I now run version 7.7.3 on the new 3 Tb Time Capsule and 7.6.3 on the 1st Gen Time Capsule. So far, the network is stable. Using WiFi Explorer Ii see that they use channel 6 and 8 respectively. Signal is strong and no dropouts have taken place so far. Hope the issue is resolved in the next firmware update.

  As I read in another post: firmware update does not solve a problem, you didn't. However, it can create a problem that you didn't.

• Last update of Windows 8 caused the interruption with internet connection

  I couldn't connect to the internet after the update. I finally had to go back in time and get rid of the update. Now my internet connection is fine. However, who am I without the update next? Does anyone else have this problem?

  Hello

   
  Please help me with the following information:
   
  1. what type of internet connection you have?

  2. What is the brand and model of the computer?

  3. do you get an error message, if yes, what is the exact error message when you lose the Internet connection?

  4. What is the number of KB updates that are installed?

  As you say, when go you back to the previous point system to remove the update Windows Internet connection works fine. lets check what update is causing the problem.

  I suggest you to install the updates of windows one by one and check the update the Internet connection problem occurs.

  Please enter the number of this update and let us know.

  Windows Update: Frequently asked Questions reference (how can I find out what were the updates installed?)

  http://Windows.Microsoft.com/en-us/Windows-8/Windows-Update-FAQ

  Additional information:

  You can see the complete procedure in the article below and check if it helps.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps, please respond with the requested information and the State of the question for any other help.

• Interruption of the connection to the host ESXi 5.1

  I did some tests on one of our hosts in preparation for the essential moving to Essentials more when I noticed that most of the vmnic reported only 100 MB Full Duplex connection speeds.  We have a Dell R515 with 2 cards Broadcom NetXtreme II BCM 5709, all set to auto negotiate, so I thought I'd try and force one vmnic to communicate to 1000Mb Full Duplex.  This had quite disastrous consequences resulting in a lack of connectivity to the host.  VCentre host is reported as Disconncted and if I try to connect directly to the host I get a type error "unable to connect".

  Fortunately the virtual machine is still ongoing so I just need to get that host online.  SSH is turned off so I can't chew on the host, if I don't have physical access to it if necessary.

  The management network is running on vmnic8, which is embedded Broadcom BCM5716, while I just changed vmnic6 on one of the Broadcom BCM5709 map, then why I lose o management network connection, I'm a little confused, any help appreciated.

  See you soon

  Dean

  Just follow the steps described in the section "setting the speed and duplex of the NIC in ESX/ESXi host at the service console. In step 1, you will find links to find out how to enable Shell access. Basically you log in to the DCUI to allow Shell access in the "Troubleshooting Options" menu and press ALT - F1 to switch to the console. After the connection, use esxcli nic network list for an overview of installed vmnic network nic esxcli get vmnic8-n to display the settings vmnic8 and esxcli network nic address-n vmnic8-a to set the speed and duplex automatic. For more information about the command, see http://pubs.vmware.com/vsphere-50/index.jsp#com.vmware.vcli.ref.doc_50/esxcli_network.html

  André

• Full service then no appeal abandoned service cannot connect to the Tower

  Posted to help others:

  I bought an iPhone 6 s it took 3 hours for Verizon connect my phone to my new Verizon account. The phone would display full service bars then, slide an or no service in bars. the phone was finally connected but may 2016 so far I sill experience the same problem of poor or no service call and dropped. Often the phone will not even scream or try to connect to the network.  Apple has replaced the phone 3 x but with no. change my service problems. Verizon and Apple senior level tech support spent to treat 30 + hours on the phone with me trying to solve this problem. We replaced the SIM cards without change. When I put the SIM card in my iPhone 6 it works fine. Full don't signal any calls interrupted and service when roaming. Back in the 6s and no service in the same place. Put the SIM card in the other Iphones not without problem.  If roaming is enabled, phone often it will not conbect to the tower at all. WiFi call is disabled and LTE voice data are on. I've disabled CDMA and data with little or no change with the problem. When iphone 6s loses the service and I toggle airport power phone it will display momentarily full service bars, then the bars one or not, while remaining connected to LTE. In some areas, I can receive calls but can not shout. Sometimes I can txt use data without showing on my plan as using FaceTime and can use the internet. The order indicated above of multiservices to no service happens within 10 seconds repeat throughout the day all areas companies Verizon towers and riaming towers. Verizon finally got the iPhone 6 s to work with full signal across remote I've ever had service, but continue to hamper the not being able to call in roaming. Shortly after that, the phone back to old habits after that they tried to solve the roaming problem.

  After 5 months of no stop calls to Verizon senior level tech supports on September 22, a high tech support tech senior level line finally came to the conclusion after 3 hours of troubleshooting determined it is a software problem Apple 100%. It determined that the phone for a month not was not connected totally to Verizon even if I used it. There to reset the SIM card and the network settings on the phone several times during this period to have the phone drop any connection after initial power that showed a full service then dropped the LTE then, he loses all the bars of service then shows no bar service then no service what so ever in 10 seconds. This was the problem with this phone on the first day.

  He explained that he has heard of what is happening and that Apple is currently working on a solution, but will not be out until possibly October 2016. He also said that this problen is happening now with new models Iphone 7.

  HE then stated that a specific sequence is usually not used must be used to reset the network settings by releasing the bug fix.

  How to restore your device

  1. First of all, back up your device using iTunes or iCloud so you don't lose any personal information.

  Note: If this is the first time that you have saved on iCloud, it may take time for several reasons (speed of Wi - Fi, amount of info on your device).

  2. Connect to iTunes to restore your device. 3. Choose "Set Up as new". 4. Make sure you that you connect to iCloud with your Apple ID so that only your contacts are re-added. Do not re - add photos, music or applications as they can be the source of your problem. 5. Set up your email. 6. Test for the next few days to determine if your problem has been resolved. 7. Restore your backup from iTunes or iCloud.

  Note: If you have a food problem, try to use the recovery mode.

  I hope this helps someone it is to have the same problems. I'm waiting to see if the bug fix works otherwise I'm going to an android phone. It has been too long a process without having a phone that works.

  I have the same problem - it has taken far too much time out of my weekend to try to resolve this problem. In addition, the Apple support person I spoke on the phone was very condescending.

  I've read elsewhere that change the LTE cell Options > Data Only will not solve the problem. So far, this seems to have worked for me.

• After update to Sierra, Mac does not connect to the ReadyNAS device

  I have two Macs at home - an iMac and a MacBook Pro.  I also have a ReadyNAS device, which acts as a time for both Machine.

  I've updated the iMac to macOS Sierra.  The upgrade went smoothly, no error reported.  However, once it was up, I found that the iMac has questions is authenticating with the ReadyNAS via AFP (and / or he would authenticate, then delete the connection) and also not able to connect to the service of Time Machine on the ReadyNAS device.

  To be sure it wasn't the ReadyNAS, I went to my MBP - it still works under OS X 10.11 and shows all the problems.  AFP shares are accessible without problem, and Time Machine works as expected.

  Has nothing changed with Time Machine or AFP protocols under macOS Sierra, which could cause this?

  The ReadyNAS is a ReadyNAS Pro 4, running 4.2.28. firmware, if it is useful.

  Thank you very much for your help!

  AFP is not used by Sierra. Try using SMB instead, if your NAS supports. Or contact the technical support of the manufacturer for assistance.

• Problem connecting to the server after moving

  Hi, I keep getting the message "there is a problem connecting to the server"192.168.0.19"etc. This happened after I moved. New ISP, new router. I have an Airport Express and a NAS connected to it. Time Machine and Icloud on the NAS. I think that the NAS has this IP address before moving. There are now 192.168.10.176. Everything works, but I get the pop up frequently.

  I look at the accounts and start but nothing. I reboot safe mode does not remove the problem. So, what can I do?

  I'm on Yosemite with MBR.

  Can you connect using the new IP address?