Connection VPN, but NO traffic

Similar Questions

• RV042 vpn - stops passing traffic but remains connected

  We have two boxes with a VPN tunnel RV042 connecting.  No problem, initiating the tunnel or passing traffic initially.  However, after "a certain" time (apparently random amounts of time) the VPN stops passing traffic.  Then, someone needs to go in web admin and disconnect/reconnect the VPN how it's ok once again.  What now happens several times a day.  FW ver is 1.3.12.6 on both sides - and addresses static ip from the ISP on both sides as well.  Any ideas on how to solve this problem?

  Thank you
  Drew

  Drew,

  Sorry I don't have a solution for you, but your post almost made me cry. We are experiencing the same problem, but with the VPN gateway to gateway static to the dynamic. I was hoping that the problem should go away if I could make the static dynamic side. It seems now I'm looking for other solutions. I wish you luck and thank you for bringing This gap to my attention.

• VPN - VPN easy hardware Client connects, but no traffic

  Hello

  I have a PIX 515E and 501 acting as a customer of material. Several remote location are connected as a easy VPN clients, a place to connect, but no traffic flows. I went from mode-extension-network client mode and I can connect through other network hosts.

  I don't know why this 501 PIX we're different. There is no ACLs except which is extracted from the station.

  Any ideas where I should look?

  Thank you

  Vince

  A few quick comments:

  1. I don't see 192.168.0.0 is part of this ACL inside_outbound_nat0_acl.

  2. I see an instance of card crypto 40 with "incomplete" crypto card, which is actually not a correspondence address.

  outside_map 40 ipsec-isakmp crypto map

  peer set card crypto outside_map 40 216.27.161.109

  outside_map card crypto 40 the transform-set ESP-DES-MD5 value

  ! Incomplete

  Not sure if it's the current configuration of the pix. If there is an instance of card crypto with an incomplete correspondence address, all traffic will be encrypted.

  Kind regards

  Arul

• Client VPN und Cisco asa 5505 tunnel work but no traffic

  Hi all

  I am new to this forum and Don t have a lot of experience with Cisco, so I hope I can get help from specialists.

  I have the following problem:

  I installed und konfigured ASA 5505 for use with vpn client. I would like to access the local network from outside through vpn.

  To test, I installed ASA 5505 with ADSL (pppoe) and tried to give access to the internal network.

  Of course whenever I have recive the supplier's different IP address, but it didn't is not a problem reconfigure in the vpn client.

  After the connection is established (vpn tunnel work) I can see my external network packets. But I Don t have any connection to the internal network.

  I erased my setup yesterday and tried to reconfigure ASA again. I didn t tested yesterday, because it was too late. And I know that I Don t have the authorization rule at present by the ACL. But I think I'm having the same problem again. (tunnel but no traffic).

  What I did wrong. Could someone let me know what I have to do today.

  With hope for your help Dimitri.

  ASA configuration after reset and basic configuration: works to the Internet from within the course.

  : Saved

  : Written by enable_15 to the CEDT 20:29:18.909 Sunday, August 29, 2010

  !

  ASA Version 8.2 (2)

  !

  ciscoasa hostname

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  PPPoE client vpdn group home

  IP address pppoe setroute

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  clock timezone THATS 1

  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 194.25.0.60

  Server name 194.25.0.68

  DM_INLINE_TCP_1 tcp service object-group

  port-object eq www

  EQ object of the https port

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 no matter what eq field open a debug session

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any object-group DM_INLINE_TCP_1 open a debug session

  inside_access_in list extended access deny ip any any debug log

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.0.0 255.255.0.0

  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.10.0 255.255.255.128

  homegroup_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  IP local pool homepool 192.168.10.1 - 192.168.10.100 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-625 - 53.bin

  ASDM location 192.168.0.0 255.255.0.0 inside

  ASDM location 192.168.10.0 255.255.255.0 inside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group home request dialout pppoe

  VPDN group House localname 04152886790

  VPDN group House ppp authentication PAP

  VPDN username 04152886790 password 1

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  TFTP server 192.168.1.5 inside c:/tftp-root

  WebVPN

  Group Policy inner residential group

  attributes of the strategy of group home group

  value of 192.168.1.1 DNS server

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list homegroup_splitTunnelAcl

  username user01 encrypted password privilege 0 v5P40l1UGvtJa7Nn

  user01 username attributes

  VPN-strategy group home group

  tunnel-group home group type remote access

  attributes global-tunnel-group home group

  address homepool pool

  Group Policy - by default-homegroup

  tunnel-group group residential ipsec-attributes

  pre-shared-key ciscotest

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:930e6cddf25838e47ef9633dc2f07acb

  : end

  Hello

  Normally, you want a static public IP address on the ASA to allow it to receive connections from VPN clients (avoid to change the IP address all the time).

  If you connect via VPN, check the following:

  1. the tunnel is established:

  HS cry isa his

  Must say QM_IDLE or MM_ACTIVE

  2 traffic is flowing (encrypted/decrypted):

  HS cry ips its

  3. Enter the command:

  management-access inside

  And check if you can PING the inside ASA VPN client IP.

  4. check that the default gateway for the LAN internal ASA within intellectual property (or there is a road to the ASA to send traffic to the VPN clients).

  Federico.

• Remote VPN on 2801 upward but no traffic

  I decided to set up a remote vpn on 2801 router. so, after some time a get my VPN tunnel to the top and State QM_IDLE but all traffic on VPN Client work around or ignored so I can't access my internal network via the VPN tunnel.

  can you please help?

  Ahhhhhhhhhhhhhhhhhhh, now I know, k first of all if it is the card top debit MOBILE, it is not supported by the vpn client

  Now we have a work around, Setup your 3 g as a connection by modem and boom, it should start working

  Kind regards

  Rebecca

• Unable to connect VPN Lenovo a800

  Dear friends

  I will try to connect to my server with VPN, but still unsuccessful said.
  but not on any other device still attached.

  My lenovo a800 model

  buidl number a800_row_s107_121216

  Android version 4.0.4

  someone at - it gives me the solution?

  Thank you

  1. install VpnRoot and BusyBox.
  2. in VpnRoot click - binary update PPPD in options
  3 standard VPN or VpnRoot connect

  =)

• A connection VPN (PPTP), who worked previously no longer works.

  original title: VPN works not

  PROBLEM:
  
  I'm running Vista 64 Ultimate SP2, with all Microsoft Updates applied.  My original CD is pre - SP1.
  A connection VPN (PPTP), who worked previously no longer works.
  I think that the problem is related to an installation of Virtual PC or iTunes, but I can't confirm either way.
  Unfortuantely, I do not have a restore point dated to before the problem.

  DETAILS OF THE PROBLEM:
  
  When I'm viewing the network drivers in Device Manager, the following drivers displayed an error:

  Miniport Wan (IP)
  Miniport Wan WAN (IPv6)
  Miniport Wan (Network Monitor)
  Miniport WAN (PPPOE)
  Miniport Wan WAN (PPTP)

  The error for each text is: "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  The following drivers do NOT display an error:

  Miniport Wan WAN (L2TP)
  Miniport WAN (SSTP)

  SOLUTIONS ALREADY ATTEMPTED:
  
  Uninstalling Virtual PC has not solved the problem.
  Uninstall device drivers and re - install it as described in the following web pages did not help the problem:

  http://www.chicagotech.NET/NetForums/viewtopic.php?p=988&SID=39aeb8e5e43c459
  http://www.howtonetworking.com/Vista/rebuildminiport.htm
  http://www.experts-exchange.com/software/System_Utilities/Remote_Access/VPN/Q_24291900.html

  In general, I am able to uninstall device drivers, but re-plant fails (sometimes reported as successful, sometimes not).

  I have presented a problem report on the failure of resettlement of Microsoft (including the following in the log files), but have received no solution:

  DMIC8E.tmp.log.XML
  LOGC9F.tmp
  netrasa.inf
  Setupapi.app.log
  Setupapi.dev.log

  I noticed that the device (loser) of WAN Miniport (PPTP) lists two files: 'ndistapi.sys' and "raspptp.sys", of which the first is NOT digitally signed, but the second is.  However, the peripheral Miniport WAN (L2TP) (work) lists only one file: "rasl2tp.sys" which is signed digitally.  This brings me to the question if my netrasa.inf installation file is currupted. (?)

  Any help would be greatly appreciated.  I am technically competent and can deal with editing the registry, etc, but need a plan of attack.

  Thank you!

  -Tad Richard

  Hi Tadrichard,

  Thanks for choosing Microsoft answers Forum.

  Is there an error when they try to establish the connection, if so, what is the error?

  Are there errors in the event logs?

  Forward for you help.
  Kind regards
  Support of yama - Microsoft.

• Any concerns of connection VPN security issue.

  Hi guys,.

  I set up a VPN on Cisco ASA & our mobility users are able to connect VPN successfully and access my LAN environment but our senior management says there provide less security & any hacker can hack easily.

  Someone can help me on this point, how can provide more security in Anyconnect VPN, I think on the Anyconnect host control features, but I think it works only with the secure desktop.

  Kind regards

  Nafis Ashique

  In short, you have just a few steps:

  1. enroll the certificate root of your PKI to customers and to the ASA (if not already done).
  2. enroll certificates from the client to the customers. It will be easier if they are in the user store. As far as I know, you cannot use the certificates stored in the IPsec VPN client store.
  3. reconfigure the ASA to use certificate authentication

  In a little more detail found in this document.

• [Issue] The connected VPN SX20, that I need more?

  Hello. I'm number one special facfing which I have never seen elsewhere.

  Please, see this photo belowed.

  

  We use the H323 Protocol with mode of ISDN G/W 3241 interal Gatekeeper to call leave SX20 to other SX20.

  You may feel weired because we do not use VCS, but instead of him, we use the internal ISDN G/W Gatekeeper.

  ISDN to IP and IP to ISDN call works well. but on the connected VPN SX20(Building D) has some problem.

  He has no problem on H323 mode "live". but, once it changed to H323 mode "keeper."

  It seems to see on ISDN G/w registed.

  but when we begin to call, building D SX20 is keeping just "Composition" State and never step of 'connection '.

  The only one I hear is unlimited ringtone SX20 building D, and the opposite of SX20 stopovers to

  Building D SX20 call also gives the same result. "the composition of demonstration" but no signal has not reached side opponent.

  This problem appeared on the VPN connection, so I need to check what I most when the value on the VPN connection for telepresence.

  Dose anyone know about this issue?

  If you want to use the feature GK, you use the gk mode.

  The VPN has very probably some treatment of layer 3 for h323 or some ports are not open.

  Behind the VPN endpoint and the rest of your ip based video systems must have

  direct ip connectivity without NAT and required ports must be open.

  And for h323, it's a whole lot of ports.

  Especially if the public ip and uri dial connectivity is on the future roadmap I would inquire

  using a vcs or cucm setup.

• Hello everyone, I just bought a Thunderbolt Apple display to use with my 2012 15 "27" Macbook Pro, Win10/Bootcamp. Is anyone know the procedure to get the display to work with Bootcamp Windows 10?  I have connected screen but no picture. TY

  Hi all

  I just bought a Thunderbolt Apple display to use with my 2012 15 "27" Macbook Pro Win10/Boot Camp running. Is anyone know the procedure to get the display to work with Bootcamp/Windows 10? Is there a setting in the training Camp that must be turned on to make it work? I have connected screen but could not get a desktop display.  Any help would be really appreciated! TY

  The monitor should have a TB and adapter power connector. The monitor works on both OSX. ? If so, shut down of windows, connect monitor and start Windows. Your TB 2012 monitor is not plug-and-play with Windows.

  Please see ports Thunderbolt and views: frequently asked questions (FAQ) - Apple Support .

  1. the "hot pluggable" Thunderbolt devices using Windows with Boot Camp?

  Thunderbolt hot plugging is supported under Windows 8 or 8.1 on all Macs from 2014 and later.

  For all other Mac computers, Windows 7, 8 and 8.1 scans and active them Thunderbolt devices connected to ports Thunderbolt during the Windows startup process. If your device has been plugged in not at startup, Windows detects not without a reboot.

• No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Original title: no local network connection

  No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Hi H.mustafaakyurek,

  ·         What operating system is installed on your computer?

  You can view the following items on the creation of a network connection:

  Setting up a network home

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

   

  Start here to set up a home network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

   

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Also see the following articles on the connection of an Internet connection:

  What do I need to connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/what-do-I-need-to-connect-to-the-Internet

   

  Allows to connect to the Internet mobile broadband

  http://Windows.Microsoft.com/en-us/Windows7/use-mobile-broadband-to-connect-to-the-Internet

  Hope this information helps.

• connection exists but not Internet

  I router AI UN xavier 7968 cnnecte my pc connection exists, but PA Internet

  I router AI UN xavier 7968 cnnecte my pc connection exists, but PA Internet

  Please re-post this in terms of the language in the menu drop-down list at the bottom of the page. This forum is for English only.

  

  If you can't find the language you need, additional language support can be found here...
  http://support.Microsoft.com/common/international.aspx

• PC won't connect wireless but with a wireless printing?

  I have windows XP and my PC won't connect wireless, but I can print wirelessly from the PC. This has happened once before, but Microsoft is not going to help me this time.

  Hello

  Please follow the steps in the link

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

• OfficeJet J6450 - printer connects wireless but does not print job cable modem replacement

  Material: My printer is an OfficeJet J6450. I am running Windows Vista, current update.

  Probably triggering the event: I replaced my modem docsis 3.0 with a doscis 2.0 modem. PSI has remained the same. All other software and firewall remained the same.

  Dysfunction: After the replacement of cable modem, I found that I could print is no longer in my HP OfficeJet 6450. I would get an error in the printer window ' error - print. "  After the reboot after the publication of the initial error, I would get the error "error - sent to the printer.

  What I did:

  As a first step, I've uninstalled and reinstalled the HP software for the printer (complete package with exception of PhotoSmart and HP customer monitoring program).

  Use the connection for the network printer wizard, I entered the router password wireless to the printer. At first I don't have a connection. Then I rebooted the computer and the printer. I also returned to the default setting of network on the printer and repeated the configuration of the network. The connection was finally successful.

  The automatic test of the network page and the network printer wizard confirms the connection. Digital display of the printer and the HP diagnostic utility has also confirmed the connection. But the diagnostic utility is unable to print a test page and throw an error - "Print Test failed.

  The result disappointing:  I still can't anything to print wireless.

  ... Thanks in advance for your suggestions to get my printer back on...

  Go to start > Control Panel > printers and delete all instances of the printer.

  Then re-add the printer:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing.  Get IP address of a Test of Netowork wireless on the front of the printer (usually in the network menu).
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• Repository working is not connect you but can connect you to master repository

  Hello

  Recently, my password to the connection diagram (master repository) database has expired. I refreshed the password. When I tested the link with the master repository it is connected successfully, but when I tested connection with referential work he demonstrated an error of invalid connection sawing repository.

  
  

  Please help me in this problem.
  

  
  

  
  

  ERROR:

  
  

  oracle.odi.core.config.WorkRepositoryResourceFailureException: ODI-10182: Uncategorized exception for access to the repository.

  Could not make JDBC connection; nested exception is java.sql.SQLException: Exception occurred while getting connection: oracle.ucp.UniversalConnectionPoolException: cannot get data source connection: java.sql.SQLException: ORA-01017: name of user and password invalid. connection refused

  	at oracle.odi.core.repository.Repository.getWorkRepository(Repository.java:195)
  	at oracle.odi.core.OdiInstance.createWorkRepository(OdiInstance.java:504)
  	to oracle.odi.core.OdiInstance. < init > (OdiInstance.java:581)
  	at oracle.odi.core.OdiInstance.createInstance(OdiInstance.java:521)
  	at com.sunopsis.graphical.dialog.SnpsDialogLoginDetail.testConnection(SnpsDialogLoginDetail.java:755)
  	to com.sunopsis.graphical.dialog.SnpsDialogLoginDetail.access$ 4 (SnpsDialogLoginDetail.java:743)
  	to com.sunopsis.graphical.dialog.SnpsDialogLoginDetail$ 2.performAction(SnpsDialogLoginDetail.java:288)
  	at oracle.odi.ui.framework.event.OdiActionListener.actionPerformed(OdiActionListener.java:69)
  	at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1995)
  	in javax.swing.AbstractButton$ Handler.actionPerformed (AbstractButton.java:2319)
  	at javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:387)
  	at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:242)
  	at javax.swing.plaf.basic.BasicButtonListener.mouseReleased(BasicButtonListener.java:236)
  	at java.awt.Component.processMouseEvent(Component.java:6288)
  	at javax.swing.JComponent.processMouseEvent(JComponent.java:3268)
  	at java.awt.Component.processEvent(Component.java:6053)
  	at java.awt.Container.processEvent(Container.java:2042)
  	at java.awt.Component.dispatchEventImpl(Component.java:4651)

  Do you use the same pattern to the work of master repositories &?

  If Yes, then you must change password in connection to the repository to work as well...

  Connect only to the master repository in ODI Studio.

  Go to the topology-> Repostiories-> repositories of work. Double-click repository work on you

  

  New window pop up on the right side. Click the card to change the password at reference work