Connection with the client VPN for RV110W problem

Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

2. internal address of the router: 10.81.208.1

3. active PPTP.  PPTP server IP address: 10.0.0.1

4 IP addresses for PPTP clients: 10.0.0.10 - 14

5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

6 encryption MPPE and Netbios active.

7 IPSec, PPTP and L2TP all active gateways.

8 VPN client: 1.4.1.2

9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

10 home network: 192.168.2.196

It is causing to tear my hair out.  What Miss me?

Shannon

Hi Shannon,

I am pleased to see that you're progress.

Shannon Rotz wrote:


I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?

You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.

Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

Answer please if you have any questions.

Tags: Cisco Support

Similar Questions

  • BlackBerry Smartphones trying to connect with the desktop software for my blackberry

    Hey, M trying to connect with the desktop software for my blackberry torch 9800 and it asks password for the connection. I am using same unlock password I use for my bb but for desktop sofware it shows incorrect... pls help!

    Make sure that you type on your BB, it's what you type in DM. don't forget that the keyboard on your BB is different from the keyboard on your PC. Some people think they are type numbers on their BlackBerry when they are really typing the letters. For example, to use numbers on a BB you must hold the ALT for each button, you push so you have to hold the alt key while typing 1 2 3 4. If you hold down the ALT key on the BB you would really be typed all W E R S. sometimes, people will hit the ALT key once (and not hold the button) before they enter the password and then you get 1 E R S.

    Who is? Make sure that you do not mix numbers and letters.

  • Problem / connection with the client to view

    Our assessment notice.

    View Manager: 4.0.1 build-233023

    Discover the composer: 2.0.0.210930

    Reviews: 4.0.1 build 2029

    So far so good. We have created a dynamic office and were able to deploy desktop computers. We use an ad group to allow users to this pool.

    To access desktop computers in this pool via the web portal is no problem, but when the same user attempts to use the Client to view we get a message that authentication has failed. In the View Manager events, I got these messages:

    1 (SESSION: E2C6C98C7A5AB8A624450E4B70DB9A78; 8 D) XXXX\YYYYYYYY: 18B0AC59A9A16F3F0158209FC1CC26) the user USER; USERSID:S - 1-5-21-nnnnnnnnnnnnn; USERDN:CN=S-1-5-21-484522859-389107532-2199480311-219035,CN=ForeignSecurityPrincipals,DC=VDI,DC=VMware,DC=int; has disconnected from VDM

    2. (SESSION: E2C6C98C7A5AB8A624450E4B70DB9A78; 8 D) BROKER_LOGOFF: USER: 18B0AC59A9A16F3F0158209FC1CC26 XXXX\YYYYYYYYY); USERSID:S - 1-5-21-nnnnnnnnnnn; USERDN:CN=S-1-5-21-484522859-389107532-2199480311-219035,CN=ForeignSecurityPrincipals,DC=VDI,DC=VMware,DC=int;

    The strange thing is, I left all this next door for a few minutes and tried to connect via Client discovered again later. This time, it worked, but at the opening of the session of office (office of screen already appeard) closes the windows desktop without any message. After you start the Client view again, the authentication will fail again.

    Time is synchronized in all entities.

    Any ideas, tips, solutions?


    AWo

    VCP 3 & 4

    \[:o]===\[o:]

    = You want to have this ad as a ringtone on your mobile phone? =

    = Send 'Assignment' to 911 for only $999999,99! =

    What ESX version are you running?  They had the 4.0 update number 2 with PCOIP, http://kb.vmware.com/kb/1022830.

    The opening of autologon, I guess that we refer to log in as current user box?    I have seen issues where if I leave my PC to the top and running for long periods of time it fails, but a simple reboot fixes this problem.

    If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

  • CSA with the Client VPN and remote access

    Hello world!

    I have the folowing isue: I have to tune in to the CSA for a clinet it connects remote with VPN Client only. He should not be able to connect to any other network or lan or dial-up.

    No idea what the policy should change or tune?

    Thank you

    You can create an access network rule that depends on a State of the system. The State of the system can be defined to have a game of skill, which belongs to the range of VPN and the network access rule would declare that the client computer cannot act as a server on UDP/TCP ports when the State of the system is ensured.

    So, if the laptop is not connected to the VPN, it would not be able to act as a server for connections to all and will be locked out. You will need to create an exception for the IP address of the VPN server to your corporate offices and allow the CSA client opening these ports.

  • create the connection with the client of sqlplus

    Hi@everybody,

    I have a little problem with the oracle Instant Client connection I installed on my Windows 7 64 bit. First of all, I have chips files:

    instantclient-basic - windows.x 64 - 12.1.0.1.0.zip

    instantclient-sqlplus - windows.x 64 - 12.1.0.1.0.zip

    and uzipped together in a directory. This directory is in the PATH in Windows 7 environment variable.

    Now I want to try to get a connection to my Oracle 11 GR 2 (11.2.0.3) database on CentOS. When I do an EasyConnect connection:

    QUICK > sqlplus system / pwdofsystem@hostname_of_db_server:1521 / NOM_SID

    There is no problem to get the database.

    But when I try along the way:

    QUICK > sqlplus "system @(DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=hostname_of_db_server) (PORT = 1521)) (CONNECT_DATA = (SID = SIDNAME)))".

    First, he asks me the password for the system. I enter the password and then I get an ORA-12560 error.

    I already read about that mistake, but I can not understand, why I need an entry in tnsnames.ora file when I gave sqlplus all parameters directly. Or is there another failure?

    Thank you and best regards,

    David

    TAKE OFF THE UNIQUE CITY, you will be connected

    Run this without single quotes.

    PROMPT > sqlplus system @(DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=hostname_of_db_server) (PORT = 1521)) (CONNECT_DATA = (SID = SIDNAME)))

    I guess if you spend the whole ting quotes, sqlplus is consider as a single 1 setting and assuming that the whole thing as username.

  • OTP-S5100 does not connect with the remote control for Sony App

    When I find devices in the remote for Sony app on my Nokia Lumia 925 blue ray player displays a code on the screen that I'm supposed to get into the app to set up the connection, but I can't find a way to enter this code into the application.  Everything I touch the recording BAROMETER.

    At this point, the media remote is only available on android and iOS.

    If my post answered your question, please mark it as "accept as a Solution.

  • Unable to connect to the Cisco VPN using the branch line

    Hello

    We use Cisco VPN Client 5.0.07.0290 to connect to our servers. We have a Sonicwall NSA2400 FW and we have 2 ISPS. We have configured load balancing on firewalls in mode 'Spill-Over '.

    So whenever the 1st line is on full charge, it will automatically moves users on the 2nd line.

    The problem that we face here is the users who get 1st line ISP, they can easily connect to the client VPN Cisco IP, but the users who receive the IP of the 2nd line of the ISP, they are not able to connect to the Cisco VPN Client. It's really annoying because everyone should be able to connect.

    It will be really great if someone can help me as well.

    Thank you

    PS: If Exchange us the line of Sonicwall haapens scenario of Vice versa as mentioned above.

    Hello Sam,.

    Correct me if I help you,.

    In your network that is inside the firewall, you are trying to connect to Cisco VPn client resides outside your network/Public network.

    If the above is the question.

    Please check the routes and roads of sonicwall priority.

    example:

    Isps1: the value of the metric as 1 for traffic destined for cisco VPn IP of the gateway and specify to leave traffic isps1 interface

    ISP2: set the metric 1 once again for the traffic to cisco VPn IP of the gateway and specify to leave traffic ISP2 interface

    interface metric 1 source destination

    Kindly, please note the useful messages and.

    Thank you

    Srikanth

  • Satellite C660 WIFI does not connect with the channel 1 of the router

    Hello

    I have this problem for several months. I connect my laptop with the D - link DIR-615 as a WAP browser.

    I can't remember, but the fact is that I can't connect more with channel 1 of my WAP.
    Connection with the other channels is no problem.

    Other laptops or the available have no problem connecting to channel 1.
    He's tried a recovery, remove and reinstall the driver for my WIFI.

    All know what to watch?

    Kind regards

    Jacky Deschepper

    Where have you changed channels settings: within the router or the wireless network adapter?
    Is that it s any laptop you are using. It s always a matter of the WLan card that is integrated.

    Usually, you can change the Wlan card settings in the properties.
    Go to Device Manager-> Wlan card-> right click Properties-> Advanced tab
    Here, you would be able to change the available settings.

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • I can't create a new site of catalyst for business with Dreamweaver CC 2014. The error message states that Dreamweaver cannot connect with the server, try again later. How can I solve this problem?

    I can't create a new site of Business Catalyst with Dreamweaver CC 2014 (Mac). The error message states that Dreamweaver cannot connect with the server, try again later. In addition, I am also unable to load remote site Business Catalyst created previously as it says that there is something wrong with my user name or password. However when I put my password and press to test the connection, he said that it has connected successfully. What is wrong and how can I solve this problem?

    Thank you

    Thanks for the reply, however it seems to work again after I removed some unused Dreamweaver sites in the section "manage sites" in Dreamweaver.  It may have been a conflict of name or something.

    Concerning

    Adrian

  • Unable to connect to the Cisco VPN you use native client: El Capitan

    I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

    When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

    * connect using the old work VPN connection: without success

    Config: Hand [server address, account name],

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    ...

    * Add new VPN connection using L2TP over IPSec: without success

    Config: Hand [server address, account name],

    Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

    Advanced [send all traffic on the VPN = TRUE]

    errsors:

    "pppd [2616]: password not found in the system keychain.

    "authd [124]: copy_rights: _server_authorize failed.

    ...


    * Add new connection using Cisco via IPSec VPN: without success

    Main config: [server address, account name].

    AUTH settings [shared secret, the Group name].

    Advanced [mode to use the passive FTP = TRUE]

    errors:

    "authd [124]: copy_rights: _server_authorize failed.

    "raccoon [2580]: could not send message vpn_control: Broken pipe"

    VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

    I. Journal of Console app existing/Legacy VPN connection:

    26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

    26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

    26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 339 [2580]: connection.

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 405 [2580]: connection.

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

    26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

    26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

    [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

    26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

    26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

    [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

    $VPN_SERVER_IP

    II. new VPN connection using L2TP over IPSec Console app log:

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

    26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

    26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

    26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

    26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

    26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

    26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

    26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

    26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

    26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

    26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

    26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

    26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

    26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

    III. New connection of Cisco VPN through IPSec Console app log:

    26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

    [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

    26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 296 [2576]: connection.

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

    26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

    26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

    26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

    26/03/16 10:19:56, 374 raccoon [2576]: connection.

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

    26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

    26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

    26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

    26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

    26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

    [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

    26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

    26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

    [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

    It seems that I solved the problem, but I'm not sure it helped.

    After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

  • How can I get the Client VPN or NAT - ted connection

    I installed a router on a customer site to replace a PC that made the NAT on a cable modem connection.

    On the router THAT NAT is done to get all the s PC on the LAN to access the Internet.

    But... one of the users use a VPN client to get to his office. With the PC, there is no problem, but given that the router is in place it can not connect.

    Because I specialized on switched networks my knowledge; edge of NAT and VPN clients.

    Is there anyone who knows how to get this VPN client-session user to be NAT - ted?

    Kind regards

    Martijn Koopsen

    If you have some onfigured of overload, then you tap the traffic. In all cases, you should at least be able to establish a connection, as IPSec uses UDP 500 for the negotiation of the tunnel. If you are not able to pass all traffic, it is another question. Once the tunnel is established, the traffic can be encrypted using the Protocol ESP who cannot be tapped under normal circumstances. If this is a cisco IPsec client, then you must discover which is the feature of termination. If it's a hub 3K, you could activate IPSec over UDP to the problem of circumvention the ESP

    Hope that helps

    Jean Marc

  • Unable to connect via the Cisco VPN Client

    Hello

    I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

    I am not able to connect and watch the journal on the SAA

    ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

    ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

    ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

    What could be the reason.

    Concerning

    Hi, I had this same problem, here is the solution:

    When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

    Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

    Well, change your strategy using MD5 isakmp / OF would do the trick.

  • Unable to connect with the listening port of the client

    [oracle@rac31 ~] $ lsnrctl status

    LSNRCTL for Linux: Version 11.2.0.1.0 - Production on March 21, 2014 03:33:30

    Copyright (c) 1991, 2009, Oracle.  All rights reserved.

    Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = LISTENER)))

    STATUS of the LISTENER

    ------------------------

    Alias LISTENER

    Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production

    Start date March 20, 2014 13:33:30

    Uptime 0 days 13 hours 59 minutes 59 seconds

    Draw level off

    Security ON: OS Local Authentication

    SNMP OFF

    Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

    The listener log file /U01/app/Oracle/diag/tnslsnr/rac31/listener/alert/log.XML

    Summary of endpoints listening...

    (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = LISTENER)))

    (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.101) (PORT = 1521)))

    (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.111) (PORT = 1521)))

    Summary of services...

    Service '+ ASM' a 1 instance (s).

    Instance '+ ASM1' READY State, has 1 operation for this service...

    'Cars' service has 1 instance (s).

    Instance "rac1" READY State, has 1 operation for this service...

    Service 'racXDB' has 1 instance (s).

    Instance "rac1" READY State, has 1 operation for this service...

    The command completed successfully

    In my server in the Oracle_HOME/network/admin

    This is my entry in tnsnames.ora

    RAC =

    (DESCRIPTION =

    (ADDRESS = (PROTOCOL = TCP) (HOST = rac-scan)(PORT = 1521))

    (CONNECT_DATA =

    (SERVER = DEDICATED)

    (SERVICE_NAME = rac)

    )

    )

    I am able to connect with the command

    sqlplus system/password@rac

    However, when I give the same input on the client computer

    It does not work

    I am able to ping the host rac-scan successfully

    C:\Users\rgehi > ping rac-scan

    Ping rac - scan.oracle.com [192.168.1.113] with 32 bytes of data:

    Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

    Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

    Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

    Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64

    Ping statistics for 192.168.1.113:

    Packets: Sent = 4, received = 4, lost = 0 (0% loss),

    Time approximate round trip in milli-seconds:

    Minimum = 0ms, Maximum = 0ms, average = 0ms

    C:\Users\rgehi > sqlplus system/password@rac

    SQL * more: Production of the version 12.1.0.1.0 Fri Mar 21 03:40:53 2014

    Copyright (c) 1982, 2013, Oracle.  All rights reserved.

    ERROR:

    ORA-12545: Connect failed because target host or object does not exist

    I installed oracle client on my desktop

    and I made entries in the tnsnames file

    However when I connect to the database to rac with scan it works sometimes...

    not always...

    so I'm in search mode and finally, after many moons a lot and light years away, I found the following

    Here's what I did

    # - scan

    192.168.0.127 rac31 - scan.oracle.com rac31-scan

    192.168.0.128 rac31 - scan.oracle.com rac31-scan

    192.168.0.129 rac31 - scan.oracle.com rac31-scan

    I put three ip addresses in the host with the same name rac31-scan file

    then I put the same ip addresses in my windows hosts file

    Here are the entries

    192.168.0.127 rac31 - scan.oracle.comrac31-scan

    192.168.0.128 rac31 - scan.oracle.com rac31-scan

    192.168.0.129 rac31 - scan.oracle.com rac31-scan

    but in the (windows 7 pc) client tnsnames file has just one entry

    It's here

    RAC1 =

    (DESCRIPTION =

    (ADDRESS = (PROTOCOL = TCP) (HOST = rac31-scan)(PORT = 1521))

    (CONNECT_DATA =

    (SERVER = DEDICATED)

    (SERVICE_NAME = RAC)

    )

    )

    and now when I connect from the client... it connects without any problems.

    I have tried more than 10 attempts without problem

    BINGO!

  • vSphere Client could not connect with the server

    Hello

    I just built a new server ESX 4.0 (update1) and tried to connect directly from the VI Client.

    He keeps fails with the following error message:

    VSphere client could not connect with the server {ip address}

    Details: The server could not interpret the customer's communication... (The remote server returned an error: (503) server unavailable.)

    I can ping the server successfully.

    Has anyone seen this problem before?

    Thank you

    for many of my cases, it's just 2-3 minutes. can you do back to the rear for connection between the server and your laptop to see there is nothing between that is causing the problem?

Maybe you are looking for

  • I can't install Adobe Flash.

    I went to a Web site, and it says that I need the latest version of the flash player. I downloaded the installed on the Adobe site. When I ran, it said that the file windows\system32\MSHTML.dll is bad. This part of Firefox? If you have a way to help

  • How to disable memory internal on Satellite A60-106?

    Hello my internal memory module is corrupt, I get a huge amount of errors with Memtest86. So I want to disable the internal memory module, because I don't want to buy a new motherboard. Is this possible? And anyone know why Toshiba makes these intern

  • Carpet * a DVD-ram UJ-845 s does not work

    Hi everyone, I'm a little crazy for my dvd player, about 14 months I bought my 3rd toshiba laptop already. In the first (Satellite 5200) dvd player (combodrive with installation of dvd ram built in) has not already after a few months. I brought this

  • LOST THE ABILITY TO WATCH THE DOC UM... & SETTINGS

    Hello guys back once more? When I press start? computer? hard drive c? I only have the symbol of a shortcut to my documents & settings?    and he used also opened upward it says acess denided what I done normally _, I can work things out, but it beat

  • 800 Microsoft wireless keyboard and mouse

    I have Windows 7 Pro OS. When I tried to install drivers and software after downloading from the Microsoft Web site, I got a "system error is not compatible, please check the system requirements" even if this device box comes indicates Windows 7 as o