Connectivity of the wireless router problem

Similar Questions

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• I received a message on my laptop computer that says not able to connect to the wireless router.

  I received a message on my laptop that says could not connect to the wireless router and it make reference to section of the knowledge base Microsoft 87112 for more information.

  I think you have transcribed the number incorrectly.  I think that the article you want is this one: http://support.microsoft.com/kb/871122

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Laptop fails to automatically connect to the wireless router.

  Original title: re automatic updates for Windows Vista

  My wife & I have laptops running Windows Vista in our House. Recently, his cell phone fails to connect to our wireless router automatically. To connect, it must get the computer to automatically get new IP settings for the network adapter. However, she must do it several times to make a connection & must be done each time it connects. My laptop is not the problem. His only started to do recently. What can we do to make his newspaper from the laptop to the internet automatically without problems?

  Hello

  Follow the steps mentioned below and check to see if they help.

  Step 1:

  Card drivers update of your network.

  Step 2:

  In addition, you can uninstall and reinstall the Device Manager wireless network card to be a safer side.

  To uninstall the wireless device manager,

  a. Click Start, type device manager in the search box of start and press ENTER.

  b. Locate the network adapters and expand the same.

  c. Select the wireless connection, right click and choose uninstall.

  d. restart the computer, if prompted.

  Pilots should settle automatically after the computer restarts.

  Now you can install the latest wireless drivers and check if this solves the problem.

• Unable to connect to the wireless router

  I can't connect to my wireless router.  My PC shows that the router has an excellent signal strength. The password is correct, but it will not connect.  What Miss me.

  Moved from Explorwer Internet

  Original title: wireless network device network Ethernet network router

  Hi Trisha,

  Many routers need firmware updates to work with Windows 7. Maybe it's the issue.

  Please answer these questions:

  1. What is the brand and model of the router?
  2. If it works much earlier?
  3. Any changes made to the computer before the show?
  4. What is the exact error message received when you try to connect to the router?

  I suggest you try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:

  Set up a wireless router

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Setting up a wireless router
  http://resource.Dlink.com/connect/setting-up-wireless-router/

  Post back with the State of the question.

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• HP photosmart 5520 cannot connect to the wireless router

  The printer has worked I went on holiday, and now it will not work. I have run the wireless network test, and it says "hp printer is unable to connect to your wireless router.  The wireless router is connected and works fine.  My hp wireless computer (windows 7) works very well.

  The structural 'found ssid network name' report, said down

  But "current configuration" has shown the SSID

  can anyone offer a fix?

  Help

  colleenmercy

  Hi colleenmercy,

  In the network menu, select default network.  This reset the current network settings and will help you reconnect the printer to the network.  You can use the Wireless Setup Wizard or reinstall the HP software to reconnect.

• I bought a Sony BDP - S185 connect Netflix Blu - ray player. I can't connect to the wireless router. Why?

  I just bought the blu - ray BDP S-185 drive so that I can access the internet (netflixetc.) on my new samsung tv. I tried to connect to my wireless router, but repeat me my connection type iswired and the connection has failed. Can I connect this player to a wireless router or should it be connected to the router? Difficult because the router is in the basement and the television on the third floor. Can I use the separator on phonejack (existing in the 3rd and.) and connect the two phone and blu ray player or do I need a netgear typedevice to connect this player? Thank you in anvance understand help. Sorry, it's so rambled butI am very confused here!

  Hi Robert,.

  Welcome to the community of Sony!

  This Blu - ray player is the BIV (Internet Video base) base model and does not support the wireless Internet connection. I suggest that you use the Ethernet LAN cable to connect the player to your router/modem.

  Thank you for your message.

• When I try to connect to the wireless router, it asks you the password I put it and he then asked again and will not accept the password. all other computers (without windows 7) connect correctly.

  My new computer has windows 7 when I try to connect it to my router it ask the password, then he asks the network password I put in the same password and it does not accept it. I spent ove an hour on the phone with a very helpful and confused expert to the Virgin. He tells me that the password only I need to communicate with the router is the main. We tried a lot of things all very technical and finally he gave up. Other computers with vista on connect very well with no problems at all.

  The network is fine and all the settings are fine. Occasionally, it connects via a home network but then it stops. When I try to communicate with the printer wireless signal stops and starts.

  I don't hold much hope of a response that experts were left very confused by this first abandoned after 45 minutes and the second lastered over an hour are totally flumaxed and blame windows 7

  But everyone told me that windows 7 was supposed to be the best

  Your post has nothing to do with the Windows Update feature (compared to the upgrade of Windows). Please repost it here for assistance: http://social.answers.microsoft.com/Forums/en-US/w7network/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Connection to the wireless router

  I currently have intermittent connection problems with my router with my wireless Vista adapter.

  Sometimes, either after booting, or the disconnection of a single account and connection on Vista another account; I can not connect. Generally, the error is expressed as security key is incorrect. However, I know that the phrase/key is correct.

  Sometimes, the adapter is disconnected and then re - set it solves the problem, while other times I had to delete and re-create the profile Wireless under the wireless network connection control panel. However most of the time I have to use to turn off the router and turned on again. It almost always does, the connection works again.

  Also, whenever a while the internet connection stops, usually when I just clicked on a web link.

  Do you know what could be the problem?

  Some journal entries you posted State "unknown user name or bad password".  This is the type of connection 2 which are attempts to connect to your PC locally (i.e. just started).  You also said earlier that when you are prompted for a security key to connect to your router, it sometimes rejects because the passkey is incorrect.  One thing that comes to mind is that you have a key that is stick on your keyboard, which is originally evil type your logon password and security key.

  Open Notepad on your computer and simply type anything.  Type your passwords and the security key passes a number of times and see if any characters repeat or not be typed at all.  If this is a Wireless keyboard, try replacing the batteries, otherwise a can of compressed air which will usually clear upward.

  If you constantly have to power cycle your router or disconnect your Wireless adapter to get a connection, then you have a hardware problem.  One of the errors you listed was "service temporarily stopped publishing because of a power event".  What happened when the error has been written?  Check with the manufacturer of these devices to see if they work properly.

  Are you able to connect to the router with an ethernet cable access to the internet without problem?

  Brent
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why can't I access the modem 192.168.1.1 when connected to the wireless router?

  I'm unable to access my DSL Modem 6100 Westell using 192.168.1.1 when connected to the Netgear WNDR3400 wireless router. I can access it, however, when I connect directly to the ethernet port on the computer without going through the router. I've set up according to the instructions. Is it possible to correct the problem?

  This isn't a problem.  This is the standard behavior.  You are connected to the side LAN of the router that is isolated from the side WAN (uplink).  This is the mode of operation of routers.

• Can connect to the wireless router, but not to the Internet

  Because I could not find this post, I published in my problem to

  Windows 7, connecting Local only, no Internet

  I think I described the problem a bit better here.

  I had a Gateway DX4300-17 with Windows 7 Home Premium for about six weeks. I connect to the Internet via a Netgear wireless router. My Internet connection dropped often, but I've always been able to reconnect to the Saturday. Since the start-up my computer Sunday, when I try to connect to the Internet, the system tells me that I am connected to the router, but there is no connection between the router and the Internet. I did a system restore to Friday, but it did not help. I searched the Knowledge Base and tried several things I found there. Running "sfc/scannow" indicates that all is well. I disabled the '6' Protocol (I don't remember the letters that were with this, but you probably know what I mean). This made no difference either. I thought I would ask for help here in the hopes of not having to restart the computer to the "hospital". That's a very different problem here barely a week. I need help, please.

  Hello Bill6009,

  Have you tried to boot your computer in SafeMode w/network to see if the problem persists?

  If so, try to perform a clean boot to see if you encounter the same problem.

  Please post back your results if we can help get your problem solved J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• B210A Photosmart - server connection error and does not connect to the wireless router

  I have problems setting up and to connect my router to my new printer b210A. Everything goes well with the initial configuration, and when asked to connect to the network at the start, it works. Then he said that the printer requires updates, downloads of updates, reboots, asks me if I want to activate eprint and as soon as I said 'Ok', I get a "the server connection error" and it is then no longer connected to the network. When I get out of the "server connection error" screen and attempt to reconnect to the network, he says 'Success', prints a Test report wireless, but never connects.

  It's the 2nd printer that I have had in a week, given that the person of HP online chatting told me my first printer had problems of "hardware", after experiencing the same problems and I'll be recommended. So - I did, and now I'm running into the same issues. The number of 800 was NO HELP - after recommended I have unplug and reconnect, then telling me there were server errors (when the printer was not connected to the network).

  We will set an IP address of the printer with a special focus on DNS domains:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway

  -For the first DNS 8.8.8.8 and 8.8.4.4 for the second use.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.