Constant network disconnects!

Hello!

I am running Windows 7 Home Premium SP1 and am using a Realtek PCIe GBE Family Controller network adapter.

A week ago, my office started constantly disconnect my Wired internet connection. I have a local network to Verizon router connection. This problem is only proceed to my office and none of the other computers or devices on the network. I tried to fix it by about three days of research, who gave no response. I reformatted my HARD drive and reinstalled windows, which solved the problem... temporarily. Today, about five days since the reformat, the disconnection problem is back.

Before I started to change my computer settings, my event logs showed:

"TCP/IP NetBIOS support was sent successfully a stop command. "The given reason was: 0 x 40030011 [OS: network connectivity (planned)].

Since then, I have disabled support TCP/IP NetBIOS, as well as the computer browser service. I also changed the settings of my network card and my SIP settings. None of these changes have solved the problem.

I also made full reboots on my desk and the router, flushed my dns cache and released / renewed my lease. These could not solve the problem either.

Out of curiosity, I started my computer in safe mode with network. After an hour or so to insist on the internet connection, there were no disconnects. I also ran a scan of viruses and software malware full system using Symantec Endpoint Protection, who gave no results.

After reading some other posts on the forum, I did tests with MiniToolBox by Farbar. The results are listed below:

ATV:

MiniToolBox by Farbar Version: 25/07/2015 01
Run by Ryan (Administrator) on 20/08/2015 at 17:47:51
From the 'C:\Users\Ryan\Desktop '.
Microsoft Windows 7 Home Premium Service Pack 1 (X 64)
Model: MS-7816 manufacturer: MSI
Boot Mode: Normal
***************************************************************************
========================= IP Configuration: ================================

Realtek PCIe GBE Family Controller = connection to the LAN (connected)

# ----------------------------------
# IPv4 Configuration
# ----------------------------------
pushd interface ipv4

reset
the value overall icmpredirects = activated

popd
# End of IPv4 configuration

Windows IP configuration

Name of the host...: Juggernaut
Primary Dns suffix...:
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.
... DNS suffix search list: fios - route .home

Ethernet connection to the Local network card:

The connection-specific DNS suffix. : fios - route .home
Description...: Realtek PCIe GBE Family Controller
Physical address.... : 44-8A-5B-5D-46-96
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::a430:1d2a:7c8b:705% 13 (Preferred)
IPv4 address...: 192.168.1.170 (Preferred)
... Subnet mask: 255.255.255.0.
Lease obtained...: Thursday, August 20, 2015 15:45:39
End of the lease...: Friday, August 21, 2015 17:47:04
... Default gateway. : 192.168.1.1.
DHCP server...: 192.168.1.1.
DHCPv6 IOOKING...: 172264027
DHCPv6 DUID customer...: 00-01-00-01-1D-5F-B9-A5-44-8A-5B-5D-46-96
DNS servers...: 192.168.1.1.
NetBIOS over TCP/IP...: disabled

Adapter isatap.fios - tunnel - route .home:

State of the media...: Media disconnected
The connection-specific DNS suffix. : fios - route .home
... Description: Microsoft ISATAP adapter
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes

Card tunnel Teredo Tunneling Pseudo-Interface:

The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
IPv6 address: 2001:0:5cf2:8c15:4c8:1 has 27: 3f57:fe55 (Preferred)
Address IPv6 local link...: fe80::4c8:1 has 27: 3f57:fe55% 11 (Preferred)
... Default gateway. : ::
NetBIOS over TCP/IP...: disabled
Server: FIOS_Quantum_Gateway.fios - route .home
Address: 192.168.1.1

Name: google.com
Address: 2607:f8b0:4007:802:1008
63.110.67.152
63.110.67.149
63.110.67.153
63.110.67.150
63.110.67.155
63.110.67.154
63.110.67.151
63.110.67.148

Ping google.com [63.110.67.151] with 32 bytes of data:
Reply from 63.110.67.151: bytes = 32 time = 35ms TTL = 59
Reply from 63.110.67.151: bytes = 32 time = 35ms TTL = 59

Ping statistics for 63.110.67.151:
Packets: Sent = 2, received = 2, lost = 0 (0% loss),
Time approximate round trip in milli-seconds:
Minimum = 35ms, Maximum = 35ms, average = 35ms
Server: FIOS_Quantum_Gateway.fios - route .home
Address: 192.168.1.1

Name: yahoo.com
Address: 2001:4998:c:a06:2:4008
2001:4998:44:204:A7
2001:4998:58:C02:A9
206.190.36.45
98.139.183.24
98.138.253.109

Ping Yao [206.190.36.45] with 32 bytes of data:
Reply from 206.190.36.45: bytes = 32 time = 57ms TTL = 53
Reply from 206.190.36.45: bytes = 32 time = 59ms TTL = 53

Ping statistics for 206.190.36.45:
Packets: Sent = 2, received = 2, lost = 0 (0% loss),
Time approximate round trip in milli-seconds:
Minimum = 57ms, Maximum = 59ms, average = 58ms

Ping 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">
Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">

Ping statistics for 127.0.0.1:
Packets: Sent = 2, received = 2, lost = 0 (0% loss),
Time approximate round trip in milli-seconds:
Minimum = 0ms, Maximum = 0ms, average = 0ms
===========================================================================
List of the interface
13... a 44 8, 5 b 5 46 96 d... Realtek PCIe GBE Family Controller
1... software Loopback Interface 1
10.. 00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11.. 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
===========================================================================

IPv4 routing table
===========================================================================
Active routes:
Network Destination gateway metric Interface subnet mask
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.170 20
127.0.0.0 255.0.0.0 127.0.0.1 on route 306
127.0.0.1 255.255.255.255 127.0.0.1 on route 306
127.255.255.255 255.255.255.255 on-link 127.0.0.1 306
192.168.1.0 255.255.255.0 on a 192.168.1.170 route 276
192.168.1.170 255.255.255.255 on a 192.168.1.170 route 276
192.168.1.255 255.255.255.255 on a 192.168.1.170 route 276
224.0.0.0 240.0.0.0 on-link 127.0.0.1 306
224.0.0.0 240.0.0.0 on a 192.168.1.170 route 276
255.255.255.255 255.255.255.255 on-link 127.0.0.1 306
255.255.255.255 255.255.255.255 on a 192.168.1.170 route 276
===========================================================================
Persistent routes:
None

IPv6 routing table
===========================================================================
Active routes:
If metric network Destination Gateway
11 58: / 0 sur-lien
1 306: 1/128 liaison
11 58 2001: / 32 on a link
11 2001:0:5cf2:8 306 15:4 c 8: 1a 27: 3f57:fe55 / 128
Over a link
13 276 fe80: / 64 On-link
11 306 fe80: / 64 On-link
FE80::4c8:1 has 27: 3f57:fe55 11 306 / 128
Over a link
FE80::A430:1d2a:7c8b:705 13 276 / 128
Over a link
1 306 ff00: / 8 On-link
11 306 ff00: / 8 On-link
13 276 ff00: / 8 On-link
===========================================================================
Persistent routes:
None

========================= Event log errors: ===============================

Application errors:
==================
Error: (20/08/2015 13:29:08) (Source: Symantec AntiVirus) (user :)
Description: Symantec Endpoint Protection doesn't have to load the latest virus definitions.

Error: (20/08/2015 13:28:58) (Source: Symantec AntiVirus) (user :)
Description: SONAR was an error: code 0: description: failed to set

Error: (20/08/2015 13:16:32) (Source: Symantec AntiVirus) (user :)
Description: SONAR was an error: code 1: description: heuristic analysis or the failed to load

Error: (20/08/2015 13:00:19) (Source: SideBySide) (user :)
"Description: activation context generation failed for" Microsoft.Windows.Common - controls, language = "*" "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version ="6.0.0.0"1."
Assembly Microsoft.Windows.Common - controls, language = "" * "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version = '6.0.0.0' could not be found."
Please use sxstrace.exe for detailed diagnosis.

Error: (20/08/2015 12:24:01) (Source: SideBySide) (user :)
"Description: activation context generation failed for" Microsoft.Windows.Common - controls, language = "*" "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version ="6.0.0.0"1."
Assembly Microsoft.Windows.Common - controls, language = "" * "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version = '6.0.0.0' could not be found."
Please use sxstrace.exe for detailed diagnosis.

Error: (20/08/2015 10:33:27) (Source: Symantec AntiVirus) (user :)
Description: SONAR was an error: code 0: description: failed to set

Error: (20/08/2015 10:33) (Source: Symantec AntiVirus) (user :)
Description: Symantec Endpoint Protection has determined that the virus definitions are missing on this computer. This computer will remain unprotected against the virus, until the virus definitions are downloaded on this computer. Application has encountered an error.
For more information, please visit: http://www.symantec.com/techsupp/servlet/ProductMessages?product=SAVCORP&version=12.1.0.0.sepe&language=english&module=1000&error=0009&build=symantec_ent

Error: (20/08/2015 10:30:34) (Source: Symantec AntiVirus) (user :)
Description: Symantec Endpoint Protection has determined that the virus definitions are missing on this computer. This computer will remain unprotected against the virus, until the virus definitions are downloaded on this computer. Application has encountered an error.
For more information, please visit: http://www.symantec.com/techsupp/servlet/ProductMessages?product=SAVCORP&version=12.1.0.0.sepe&language=english&module=1000&error=0009&build=symantec_ent

Error: (19/08/2015 13:25:28) (Source: SideBySide) (user :)
"Description: activation context generation failed for" Microsoft.Windows.Common - controls, language = "*" "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version ="6.0.0.0"1."
Assembly Microsoft.Windows.Common - controls, language = "" * "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version = '6.0.0.0' could not be found."
Please use sxstrace.exe for detailed diagnosis.

Error: (18/08/2015 17:10:15) (Source: SideBySide) (user :)
"Description: activation context generation failed for" Microsoft.Windows.Common - controls, language = "*" "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version ="6.0.0.0"1."
Assembly Microsoft.Windows.Common - controls, language = "" * "processorArchitecture ="arm", publicKeyToken = '6595b64144ccf1df', type is 'win32', version = '6.0.0.0' could not be found."
Please use sxstrace.exe for detailed diagnosis.

System errors:
=============
Error: (20/08/2015 15:41:54) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:41:54) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:41:54) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:39:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:39:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:39:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:34:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:34:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:34:48) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Error: (20/08/2015 15:33:30) (Source: Service Control Manager) (user :)
Description: The computer browser service depends on the Server service which failed to start because of the following error:
% 1068

Sessions of Microsoft Office:
=========================
Error: (20/08/2015 13:29:08) (Source: Symantec AntiVirus)(User:))
Description: Symantec Endpoint Protection doesn't have to load the latest virus definitions.

Error: (20/08/2015 13:28:58) (Source: Symantec AntiVirus)(User:))
Description: SONAR was an error: code 0: description: failed to set

Error: (20/08/2015 13:16:32) (Source: Symantec AntiVirus)(User:))
Description: SONAR was an error: code 1: description: heuristic analysis or the failed to load

Error: (20/08/2015 13:00:19) (Source: SideBySide)(User:))
Description: Microsoft.Windows.Common-Controls,language="*",processorArchitecture="arm",publicKeyToken="6595b64144ccf1df",type="win32",version="6.0.0.0"C:\Users\Ryan\Downloads\vcredist_arm.exe

Error: (20/08/2015 12:24:01) (Source: SideBySide)(User:))
Description: Microsoft.Windows.Common-Controls,language="*",processorArchitecture="arm",publicKeyToken="6595b64144ccf1df",type="win32",version="6.0.0.0"C:\Users\Ryan\Downloads\vcredist_arm.exe

Error: (20/08/2015 10:33:27) (Source: Symantec AntiVirus)(User:))
Description: SONAR was an error: code 0: description: failed to set

Error: (20/08/2015 10:33) (Source: Symantec AntiVirus)(User:))
Description: Symantec Endpoint Protection has determined that the virus definitions are missing on this computer. This computer will remain unprotected against the virus, until the virus definitions are downloaded on this computer. Application has encountered an error.
For more information, please visit: http://www.symantec.com/techsupp/servlet/ProductMessages?product=SAVCORP&version=12.1.0.0.sepe&language=english&module=1000&error=0009&build=symantec_ent

Error: (20/08/2015 10:30:34) (Source: Symantec AntiVirus)(User:))
Description: Symantec Endpoint Protection has determined that the virus definitions are missing on this computer. This computer will remain unprotected against the virus, until the virus definitions are downloaded on this computer. Application has encountered an error.
For more information, please visit: http://www.symantec.com/techsupp/servlet/ProductMessages?product=SAVCORP&version=12.1.0.0.sepe&language=english&module=1000&error=0009&build=symantec_ent

Error: (19/08/2015 13:25:28) (Source: SideBySide)(User:))
Description: Microsoft.Windows.Common-Controls,language="*",processorArchitecture="arm",publicKeyToken="6595b64144ccf1df",type="win32",version="6.0.0.0"C:\Users\Ryan\Downloads\vcredist_arm.exe

Error: (18/08/2015 17:10:15) (Source: SideBySide)(User:))
Description: Microsoft.Windows.Common-Controls,language="*",processorArchitecture="arm",publicKeyToken="6595b64144ccf1df",type="win32",version="6.0.0.0"C:\Users\Ryan\Downloads\vcredist_arm.exe

CodeIntegrity errors:
===================================
Date: 18-08-2015 17:52:27.808
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\x86_microsoft-windows-errorreportingcore_31bf3856ad364e35_10.0.10074.1_none_47662a2706182d6f\wermgr.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.805
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\x86_microsoft-windows-errorreportingcore_31bf3856ad364e35_10.0.10074.1_none_47662a2706182d6f\wermgr.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.748
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\amd64_microsoft-windows-errorreportingcore_31bf3856ad364e35_10.0.10074.1_none_a384c5aabe759ea5\wermgr.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.746
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\amd64_microsoft-windows-errorreportingcore_31bf3856ad364e35_10.0.10074.1_none_a384c5aabe759ea5\wermgr.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.676
Description: Windows is unable to verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\amd64_microsoft-windows-errorreportingfaults_31bf3856ad364e35_10.0.10074.1_none_f3153036f55ab3f5\werfault.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.673
Description: Windows is unable to verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\amd64_microsoft-windows-errorreportingfaults_31bf3856ad364e35_10.0.10074.1_none_f3153036f55ab3f5\werfault.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.624
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\x86_microsoft-windows-errorreportingfaults_31bf3856ad364e35_10.0.10074.1_none_96f694b33cfd42bf\werfault.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 18-08-2015 17:52:27.621
Description: Windows cannot verify the integrity of the file \Device\HarddiskVolume2\$Windows.~BT\Updates\Critical\8e08ca47-f6ba-409d-82de-698e324c0004\x86_microsoft-windows-errorreportingfaults_31bf3856ad364e35_10.0.10074.1_none_96f694b33cfd42bf\werfault.exe because the signing certificate has been revoked.  Check with the Publisher to see if has signed a new version of the kernel module is available.

Date: 17-08-2015 13:48:27.078
Description: Code integrity cannot verify the integrity of the image of the file \Device\HarddiskVolume2\Windows.old\Windows\winsxs\wow64_microsoft-windows-appid_31bf3856ad364e35_6.1.7601.23040_none_c02bb2f816616adb\appidapi.dll because all of the image per page hashes is not found on the system.

Date: 17-08-2015 13:48:27.043
Description: Code integrity cannot verify the integrity of the image of the file \Device\HarddiskVolume2\Windows.old\Windows\winsxs\wow64_microsoft-windows-appid_31bf3856ad364e35_6.1.7601.23040_none_c02bb2f816616adb\appidapi.dll because all of the image per page hashes is not found on the system.

= Programs installed =.

Armored war MyCom Beta (HKCU\...\Armored Warfare MyCom Beta) (Version: 1.25 - My.com B.V.)
CCleaner (HKLM\...\CCleaner) (Version: 5.08 - Piriform)
Google Chrome (chromium HKLM-x32\...\Google) (Version: 44.0.2403.155 - Google Inc.)
Update Google Helper (HKLM-x32\...\{60EC980A-BDA2-4CB6-A427-B07A5498B4CA)} (Version: 1.3.28.5 - Google Inc.) Hidden
HP Photosmart 5520 series based Device Software (HKLM\...\{68C0736C-3E47-43A6-B14D-236BEF198A5F)} (Version: 28.0.1315.0 - Hewlett-Packard Co.)
HP Support Solutions Framework (HKLM-x32\...\{F6A11738-3EE4-4573-AEA5-6CD5D491C167)} (Version: 12.0.30.81 - Hewlett-Packard Company)
Microsoft .NET Framework 4.5.2 (HKLM\...\{92FB6C44-E685-45AD-9B20-CADF4CABA132} - 1033) (Version: 4.5.51209 - Microsoft Corporation)
{Microsoft Visual C++ Redistributable (x 64) 2013 - 12.0.30501 (HKLM-x32\...\{050d4fc8-5d48-4b8f-8972-47c82c46020f)} (Version: 12.0.30501.0 - Microsoft Corporation)
{Microsoft Visual C++ Redistributable (x 86) 2013 - 12.0.30501 (HKLM-x32\...\{f65db027-aff3-4070-886a-0d87064aabb1)} (Version: 12.0.30501.0 - Microsoft Corporation)
{Mumble 1.2.10 (HKLM-x32\...\{63243F5C-E941-4461-A4B0-2689A9A3BF13)} (Version: 1.2.10 - Thorvald Natvig)
My.com Game Center (HKCU\...\MyComGames) (Version: 3.140 - My.com B.V.)
NVIDIA 3D Vision Controller Driver 352.65 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_Display.NVIRUSB) (Version: 352.65 - NVIDIA Corporation)
NVIDIA 3D Vision Driver 353.82 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_Display.3DVision) (Version: 353.82 - NVIDIA Corporation)
NVIDIA Graphics Driver 353.82 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_Display.Driver) (Version: 353.82 - NVIDIA Corporation)
NVIDIA driver HD Audio 1.3.34.3 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_HDAudio.Driver) (Version: 1.3.34.3 - NVIDIA Corporation)
NVIDIA PhysX System Software 9.15.0428 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_Display.PhysX) (Version: 9.15.0428 - NVIDIA Corporation)
Update NVIDIA 10.4.0 (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_Display.Update) (Version: 10.4.0 - NVIDIA Corporation)
MOC ModPack Client version 1.4.0.0 (HKLM-x32\...\{E2F3187C-2B94-486F-8914-E69211487FB6}_is1) (Version: 1.4.0.0 - Odem Mortis)
Razer Synapse (HKLM-x32\...\{0D78BEE2-F8FF-4498-AF1A-3FF81CED8AC6)} (Version: 1.18.21.26914 - Razer Inc..)
Realtek Ethernet Controller Driver (HKLM-x32\...\{8833FFB6-5B0C-4764-81AA-06DFEED9A476)} (Version: 7.92.115.2015 - Realtek)
SHIELD streaming (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_GFExperience.NvStreamSrv) (Version: 4.1.3000 - NVIDIA Corporation) hidden
SHIELD (HKLM\...\{B2FE1952-0186-46C3-BAEC-A80AA35AC5B8}_ShieldWirelessController) wireless controller driver (Version: 2.5.12.11 - NVIDIA Corporation) hidden
Steam (HKLM-x32\...\Steam) (Version: 2.10.91.91 - Valve Corporation)
Symantec Endpoint Protection (HKLM\...\{A5DCF955-5D4A-471D-8CB3-DCFDF5C5DEE7)} (Version: 12.1.5337.5000 - Symantec Corporation)
TeamSpeak 3 Client (customer HKLM-x32\...\TeamSpeak 3) (Version: 3.0.17 - TeamSpeak Systems GmbH)
Warframe (HKLM-x32\...\{A42DFA57-3412-4337-B96A-25AA241E6D81)} (Version: 1.0.0 - Digital Extremes)
WOT (HKCU\...\{1EAC1D02-C6AC-4FA6-9A44-96258C37C812na}_is1) (Version:-Wargaming.net)
World warships (HKCU\...\{1EAC1D02-C6AC-4FA6-9A44-96258C37C814na}_is1) (Version:-Wargaming.net)

========================= Memory info: ===================================

Percentage of memory used: 31%
Physical RAM total: 8135,98 MB
Available physical RAM: 5552,67 MB
Total virtual: 16270,17 MB
Available virtual: 13616,05 MB

========================= Partitions: =====================================

1 drive c: () (fixed) (Total: 931.41) (Go free: 360.16) NTFS
2 drive d: () (CDROM) (Total: 0.66 GB) (free: 0 UDF OF GO)

========================= Users: ========================================

User accounts for \\JUGGERNAUT

Guest administrator Ryan

End of the log *.

Any help on this would be greatly appreciated!

I hope someone has an answer that works! I tried to contact microsoft directly, and after waiting for more than two hours, the call is dropped.

Thanks in advance!

It is possible that the problem has nothing to do with your computer, but a problem with the router we to branch or even the cable itself.

It is also possible that network on your computer installation has failed.

You can probably find a plug in pension that will adapt to your desktop which can be used for another installation of network.  They should be easy to find and relatively inexpensive.  I saw this solution work several times.  Simple and cheap.

My best advice is to stop misleading with Windows before making a mess of it.

Tags: Windows

Similar Questions

  • Network disconnects the Tecra M7 using Windows 7 RTM

    I tested Windows 7 since the first versions beta and finally got my driver's license for RTM, but one thing still does not work on the Tecra M7:

    Network connectivity is lost repeatedly during the use of the ethernet adapter integrated Intel Pro/1000 PL.
    Installing latest drivers (06/05/2009,9.13.12.0), everything is put in place, but the DNS appear to be lost.

    Repeatable after putting the computer to sleep and prolonged sleep and wake up - irreproducibly randomly while connected.
    ipconfig/release, ipconfig / renew does the trick then - pull the plug and put it back is NOT.

    Somtimes, ipconfig doesn't solve the problem for a few minutes - in this case, only a reboot help

    I have two machines, same model, both show the same problem - tested various networks (managed, public/private, 10Base-T/100Base-TX).

    Anyone have any idea?

    Hello

    After wake up sleep or hibernation mode, you mean the network disconnects automatically?

    I think that it is a software problem
    I remember that Vista and first BONE had the similar problem
    Usually, the update driver and Windows update helped but since Win7 is not official on the market, you will have to wait for official updates and patches

    PS: have you noticed the same thing using the OS preinstalled Toshiba?
    Your BIOS is up to date?

  • OfficeJet 8500 product constant network activity

    I just installed an Officejet Pro 8500 all-in-One as a cable network printer.  The network has the OJ8500 and 2 computers (Win XP), but the OJ8500 software is installed on a single computer.

    Since the installation is complete, there is constant network (two seconds) traffic between the OJ8500 and the computer.  Questions.  Exactly what part of the software OJ8500 is originally the network activity?  What I have to change in order to minimize or eliminate the network activity?  Can I eliminate network activity and still continue to use the features of the OJ8500?

    Thanks in advance for your help.

    Our SW printer queries the printer every three seconds (or two) for admission to the status and to detect if the computer scanning function has been started (a decision of regrettable design IMHO).  Traffic is relatively low at ~ 60 bytes/s about.

    You can stop the modalities of the election even if you lose some features of the printer - including the ability to start the printer scans and detection of the ink levels.  If you wish, you can try to experiment with disabling the HP Digital monitor start-up service in your Windows machine.

  • Office network disconnects and refuses to connect.

    Original title: network path cannot be found/nom_peripherique unrecognized - peripheral network disconnect themselves, do not share network

    Our firm has a network that connects the main CP in the conference room with the printer/scanner and all other PCs in the office. Recently he started to disconnect randomly various devices, why is this? Once, it disconnects often refuses to recognize other devices on the network names or indicates the network path was not found. Why is it a few days and then all of a sudden a computer disconnects? Is the wifi modem on our pc reception causing th eproblem because its old? the firewall settings cannot be because most of the affected epcs th have active firewall? Please help, it is really hard to share information at the office without the network and even more difficult when the internet refuses to connect as well!

    Hi Maxine,

    Welcome to Microsoft Community where you can find all the answers related to Windows.

    According to the description, it seems that you have a problem connecting to the other computer in a corporate network. This problem is linked to the domain (company network), you can contact the administrator of the network of the office or write the topic in the Technet Forum for better support.

    Visit this link to report the issue in the Technet Forum.

    Hope this information helps. Answer us queries windows and we will be happy to help.

  • G560 - network disconnected after waking up from hibernation

    During the last two days, my laptop Lenovo G560 (running Windows 7, 64-bit, BIOS 2.10) has had problems with its (wired) network card after waking from hibernation. It is shown as disconnected (even as if the cable was physically detached). The only big change I played in the last few days has been installed Service Pack 1. However, the problem only appeared about two days after, so I don't know if this is related at all.

    In this case, IPCONFIG shows the following for the NETWORK card:

    Ethernet connection to the Local network card:

    State of the media...: Media disconnected

    If I try IPCONFIG/renew, I get

    Windows IP configuration

    No operations can be performed on the connection to the Local network, although it has its media disconnected.

    Hovering over the said tray icon "not connected". Troubleshooting of course can't find anything. Also, there is no weird in event viewer entries (unless they are hidden somewhere in other modes). Basically, the behavior is identical to when the network cable is physically disconnected (disconnected).

    In addition, disconnect the network cable, wait a few minutes and in him plugging back again once does nothing.

    For now, I have two workaround solutions:

    -system reboot

    -right click on the connection to the Local network (in network connections), select DISABLE from the menu, wait a few moments and then choosing the option ENABLE on the shortcut menu.

    Is there a better solution to this? Speculation on what might be the reason for this problem all of a sudden?

    Right click on my computer > manage > device management > network cards > select wireless adapter > properties > under power management tab, clear the check box to be able to save "allow the computer to turn off this device to save power".

    Restart your computer and check if it works.

    Please post back with the results.

  • Wanted M6-AE151DX: wireless network disconnecting after rest

    I lose my connection Wireless to my home network if my PC is idle for a period of time. I have to disconnect and then back to the network access. No idea what is the cause and how to fix?

    Hello

    Please try the following steps

    b click Start,

    b click on Device Manager,

    (c) develop the network adapters,

    d right clisk wireless adapter and select Properties.

    (e) go to the power management tab.

    (f) uncheck the box "allow the computer to turn off...". »

    (g) click Ok/apply

    Kind regards.

  • When I'm not on my computer, the network disconnects, and I need to reboot Windows XP to run again.

    original title: it is a boot sector virus

    Please no one knows the answer?

    I use MSE on XP. Have all implemented the automatic updates firewall that all fixed at a fairly high level of security, and to update and scan with MSE usually twice a day. When I'm not using the computer I disconnect the network and reconnect when then necessary safety precaution.

    Sometimes, when I return to the computer is not found on the network, and the only way to restore the network connection is to re-boot. Then, I find it almost impossible to re-start as he died within 5 seconds after pressing the power button / stop. I tried holding the power button for a few seconds, but nothing helps I just keep on pushing sometimes for dozens of attempts and it stops automatically turn off the power. He intercepted not eventually if I keep on pressing him for dozens and dozens of attempts. It is?, is it a virus of a description, and if this is what and how is he riding in, on and why is MSE does not pick up.   I had similar situations where the IP address of my printer (Ricoh Aficio) has been changed, then turn off the printer and thrusting me on an audit of the laborious systems. ?.  Anyone has any ideas.

    Thank you very much

    Bob.

    PS Merry Christmas and a happy new year to all.

    Of course, it sounds as if you use the power button on the computer case.  Otherwise, good.

    Then, I find it almost impossible to re-start as he died within 5 seconds after pressing the power button / stop. I tried holding the power button for a few seconds, but nothing helps I just keep on pushing sometimes for dozens of attempts and it stops automatically turn off the power. He intercepted not eventually if I keep on pressing him for dozens and dozens of attempts.

    I guess that until you're away from the computer, disconnect from the network.  Even if you don't have the computer off, disconnect is still excessive.  However, if you do this, Windows should not bother you that you describe.

    During your absence, the computer go to sleep or Hibernate mode (if so, which) or have you configured it stays on indefinitely until you deliberately shut down?  If the computer is set to go into sleep or Hibernate mode after a certain period, you have the same problem reconnecting to the network if you return before the computer is spent in sleep mode or Hibernate mode?

    You have Service Pack 3 and the subsequent critical updates installed (for example, you use automatic updates)?

    The next time the problem occurs, open the event viewer (start > run > eventvwr > OK) and look in the Application logs and system errors or warnings.  By default, when you open the log event viewer must be sorted with the most recent events at the top.  If not, click the title once (or twice) of the column to sort.  He can't go very far back to find questions.  If there is an error or a warning, double-click it to display the property page.  Then click on the copy icon (right underneath the up/down arrows).  Then paste in your response here.

    You have your router configured to disable the SSID broadcast?  Even if it sometimes seems on Web sites for safety, it does not add to your safety really but creates network problems.  Do not disable the SSID broadcast, especially for Windows XP machines.  See http://blogs.technet.com/b/steriley/archive/2007/10/16/myth-vs-reality-wireless-ssids.aspx as this article points out, also not use MAC filtering in your router.

    Another thing that might cause problems of reconnection (especially if you have your router's SSID broadcast disabled) is a connection to a nearby unsecured wireless network.  You should look through the list of preferred networks tab in wireless network your wireless adapter properties dialog box, and 'Delete' you don't want to connect to all networks.  To get here, open network connections (start > run > ncpa.cpl > OK), right click on the wireless adapter and choose Properties.  Then go to the wireless networks tab.

    Even if you have properties of the adapter wireless open dialog box, select your network from the list of preferred networks and click Properties. Then click on the tab 'connection '.  What is the box checked for automatically "connect if this network is in range"?

    Finally, in regards to your printer, it is a recommended practice to configure devices like printers have a static IP address instead of the obtain an IP address from the DHCP server on the router.  As you have observed, in some circumstances (the printer is off for awhile), the router can assign a different IP address for the router than he had when you first set up the things.  Some wireless printer drivers (HP, for example) are smart enough to deal with this, but most is not.

    Read the manual of your Ricoh printer to determine how to assign a static IP address.  Pick one that is in the same subnet (i.e., the first 3 bytes of the IP address are the same as your other IP addresses), but out of the interval used by the DHCP server on your router.  You can find this information from the router configuration utility.

    For example, the DHCP server on my Linksys router is configured to assign not more 10 starting at 192.168.1.100 IP addresses.  Which means that the first computer to connect will get 192.168.1.100, the second 192.168.1.101 and so on.  So I configured my wireless printers to have a static IP address that is lower than, for example 192.168.1.50.

    After you set up the printer, click Start > printers and faxes.  Right-click on your printer, and then select Properties.  Click the Ports tab.  Already, the correct port must be selected.  Click on Configure Port.  OK your way out and enter IP address static, that you assigned to the printer.

  • NETWORK DISCONNECTS RANDOMLY, I READ EVERYTHING HERE AND NOTHING WORKS, PLEASE HELP ME! :(

    Lenovo G510
    Intel core i5 - 4210M
    Windows 7 ultimate
    Broadcom 802.11n network adapter

    For almost a month I had problems with my laptop because it disconnects randomly the system for some reason, I can't identify.
    It can operate correctly for one hour, then disconnects the wireless network card. Every now and then, or every 10 minutes, depends on the day I guess.
    I had a lot of reading the forums on this topic and found nothing to work up to now
    That's what I tried:
    -everything is on maximum performance
    decliques-i 'allow the computer to turn off this device to save power ".
    -disabled some 'ip helper' in services
    -check all that relates to the router (change channels, interference with other routers or wifi), the hardware part SEEMS very well (the laptop is fairly new, it's like a year and never had any problems with it)
    -verification of updates of drivers, it says I have the latest version
    -fully scanned the laptop for viruses and none has been detected
    n ' install any programs lately that could cause this
    -network, signall is excellent

    And still nothing worked. NOTHING. I'm really desperate now. The only thing that makes the network working again almost instantly (like5-10 sec then that if I let him restart itself it takes 2 minutes for even 30-40 minutes), turn and turn again on the wireless network card (I have it by pressing the airplane mode)
    If no help pleaseeee? I noticed that it happens to many other users also.

    If the steps we have provided above has not resolved the problem with intermittent wireless connectivity, then what Canadian technology said, it is likely that the problem lies in the material.

    Intermittent wireless connectivity are often caused by loose or defective air intakes to the wireless card, or a faulty card as well. This is the reason why Canadian Tech informed on the use of an external USB wireless device.

    Another option is to contact the manufacturer of your device, which is Lenovo, for repair options based on security they provide. You can contact them via this link.

  • Internet host and network disconnection continuous

    Background: A contractor for the cable company spliced my line so that the new neighbor could get cable (only my address has been marked on the box and there was a cord connecting it under their fence). I called and they sent someone who said they would get someone else to fix it. Since my internet disconnects all day and all night. I called the cable company and finished by somebody who had a sense and really tried to help him. He created my own network and pass the word. My internet was faster than it had ever been perfect. However a few hours later he did the same thing again and kept 3.5 MONTHS later.

    Technology had said that he could see that one of my neighbors was using a ham radio and radio which created a 'shield' on all the networks and could see that my neighborhood was having the same problems. I asked why they weren't Campeau in-not of true response. I called so many times I can't remember how many, and even a technician had come out and change my modem. When he had it ready to go he said that he did not work well.

    Whenever I call it they say that the 'Nice' tech has no idea what he's talking about and that it is impossible to block someones internet.

    Can someone help me?

    Hi Lisa,

    Thanks for posting the query on Microsoft Community.

    If I understand correctly, you can not access the internet as network keeps disconnecting. We appreciate your patience and your efforts.

    1. What is the brand and model of the computer?
    2. What is the full error message that you receive when you try to access any Web site?
    3. As you informed 'could see that my neighborhood was having the same problems.', others also face the same question again?

    Try to run the network troubleshooter utility and other steps in the link below.

    Why can't I connect to the Internet? :

    http://Windows.Microsoft.com/en-in/Windows/cant-connect-Internet#1TC=Windows-7

    I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.

  • Why the network disconnect?

    During normal use, my network to the internet is disconnected, so I restart the window, and the network works fine.

    During normal use, my network to the internet is disconnected, so I did nothing and that the network is working fine after a few minutes.

    Based on the above cases, I would like to know about any potential cause on disconnecting from the network.

    Does anyone have any suggestions?

    Thanks in advance for your suggestions

    Hello

    1. what type of internet connection do you use? Is it wireless or wired?

    2. which antivirus program is installed on the computer?

    3. using Internet Explorer as your default browser? If Yes, what version of IE are you using?

    4. do you receive any error messages?

    This problem normally occurs when there is no problem with the connection you are using. It can also occur if the antivirus program blocks specific ports. The steps described here.

    Method 1: Run the network troubleshooter

    Wireless and wired network problems

    http://Windows.Microsoft.com/en-AU/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    Method 2:

    Temporarily disable the security software and check.

    Caution:

    Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

    Hope this information helps. Response with status so that we can help you.

  • Desperate cry for help - Win7 and SBS 2008 sharing network/disconnections

    Hi all

    I am facing a problem of bad guy who frustrated me for several weeks now!

    Scenario:
    1 Windows Server 2008 SBS Premium Edition (not R2)
    Network share: \\Server\DBShare
    also mapped as J:\ on client computers
    Share contains some databases Access 2002 ("access xp") back-end (BE)

    2. customers: all diversified machines: XP, Vista, Win7, etc...
    ALL have Access XP (2002) installed (runtime) and run a horrible old 13 year front-end (FE) which has been spasmodic developing since 1997. It is mission critical and there is no budget to rewrite is because it is sprawling and has its hooks in each device, procedure, policy and activity that we do.
    Front-end is run locally, lies in the path of users % appdata %.

    Problem:

    Currently 8 x peripheral non-Windows 7 system to access every day, stay connected 24 hours a day and never give disk errors or network.

    ANY windows 7 machine is guaranteed to give disk or network error messages at some point - from 30 minutes to 15 hours by opening the front end and be left idle.

    NOTE: I was sent here on the forum to access because they thought that Win7 forum would be more appropriate. For non-access users, Access is like the Canary in the coal mine
    with regard to the problems of network connection. Even a slight network disturbance causes to complain about errors on the network and to require the connection to database
    to be re-created, data loss and potentially damage this database to the file system.

    I had all the world put in place using j:\variousdatabases.mdb, but read it as one
    Nono so I scripted a change in all the drives mapped to UNC paths in the
    connection of these tables property.  With this change, sometimes I just
    get an "odd" error disk or network, then am able to reconnect - but this
    bothers me terribly because 1. It can do damage to the db, 2. He
    means that I must write to this trap for more than 300 forms and even the management of errors
    so I think that there will be some things that I can't trap and 3. It is also SOMETIMES
    do not reconnect and I get messages repeated... or even an appcrash.

    When I say EVERYTHING, I mean I have 4 test devices: a work station, a Mini PC, a
    laptop and a netbook. This started as a 'test upgrade' to Win7 on the
    post work - but after this Show-stopping number, it became a desperate
    Troubleshooting jamboree, involving more than systems and other tests, because the
    solution seemed just around the corner.

    Now, a week later, I'm ready to give in on computeres forever and go live
    under a bridge, since I am unable to solve this problem and have already invested so much
    a lot of time into it!

    Here's what I think, that I decided to go out and why:

    Not a problem of network infrastructure.
    I can unlug a minipc with vista on it (same exact material) and connect it to the
    the ethernet port on a win7 test evil machines and it plugs.
    Fortunately for more than 24 hours. All the machines are on the same switch 24 ports. All the
    nonwin7 machines work as if in a dream, even when moved to the port/cable
    used by the machines of win7.

    Not a problem of a server NETWORK card.
    See above. Other devices not win7 Purring immediately without disconnecting.

    Not a server problem.
    SBS2008 works * Virgin * for the last 7 months. Only the reason for
    glance has been recently to try to resolve this problem of fools...
    All clients not win7 are happy as can be, always.

    The EM is not (apparently horrible?) dynamic TCP stack scaling or unloading on the
    SERVER.
    EVERYTHING in the driver for the card that could be discharged (and has been by default,
    no problem on other non-win7 clients) has been decommissioned. I also have
    off the chimney and any other devices of automatic setting on the server.
    (FYI - all STILL happy nonwin7 clients, server shows no significant increase)
    in the CPU usage)

    The EM is not (apparently horrible?) dynamic TCP stack scaling or unloading on the
    CLIENTS.
    Doing the same thing again on clients - auto tuning off the coast, where the unloading off
    possible. Latest installed NETWORK card drivers that give many options of unloading
    to turn off.

    No offline files
    These have been disabled on the server, on the client and in the group shares
    policy just to make a point.

    Not the MiniPc / the workstation laptop / Netbook / la
    Seems unlikely that all 4 would not work because of the material error AND
    drivers of offensive, but I ran out of ideas - so I photographed the MiniPC win7
    and put Vista on. To my great regret, the Vista OS on the same device works
    perfectly. Recreate the image of the OS Win7 and BOOM - same problem.

    No IPv6
    Disabled on the clients and the server

    No IPX/SPX
    Not installed on the server

    No network traffic
    (happens when I'm all but 5 computers off tension and nobody in the)
    Office as well in the middle of the day when users are 'use'.)

    Not the time of day
    Sometimes after 15 minutes in the middle of the afternoon or after 6 hours to
    04:32 - does not coincide with the events of on the server or the client error log, does not
    coincide with DHCP renewals (which are in 2 weeks)

    No server autodisconnect
    The value - 1 both server and client (I know that's irrelevant on the client))
    I also tried to add a ffffff keepconn regentry (I know that the stated max is
    64 k, but it doesn't help me have the connection after 18 hours.)
    FYI - no effect with or without the keepconn registry entries.

    Not be able to save
    4 machines, 4 different ranges of stuff randomly to stop turning out - of
    NICs for windows power plans to simply disable acpi. Problem
    continues

    Not my version of Windows 7
    Tried our company VLK Win7 and my personal copy of win7 ultimate
    and the NetBook win7 Home premium. SAME SAME SAME

    Not my drivers up to date
    MS stock on old machines drivers that are not built for Win7 show me the
    same error
    Laptop and Netbook (the latter preinstalled by the vendor) also give the same problem

    It is not that I do not use the drive\UNC.
    I ran a separate script that does just a DIR() on file every 10 seconds
    and yet, I finally get disk errors.

    It is not that I am not query the database and the connection is time
    There is a database search all 2 minues in PA to check new data in a table

    This isn't a field/roaming profile issue
    I tried logged as a domain with the profile user roaming user admin not now
    the area, officially added to the domain and even laptops PCs
    not registered on the domain.

    It's not the system restore
    Disabled on clients

    Is not SMB signing
    This is disabled in server group policy and still the same problem...

    Help, please!

    Any ideas would be much appreciated!

    Thank you in advance to help improve my new year! & Happy holidays to those of you luck is not to be this troubleshooting!

    Alex

    Thanks diana,.

    I tried my luck in the Technet Server forum you suggested.

    For others who want to follow my progress, here is the link:

    http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/thread/0527a084-1953-47f0-ae83-febb52af14fc

    Happy new year!

  • Wireless network disconnects randomly

    Original title: Windown 7, guard disconnect the dsl modem, can only connect after a system restore function, which causes this failure?

    For several weeks, Windows 7 keeps disconnect to the ADSL modem.  Canconnect only after a system restore function.  What causes this failure?

    Hello

    1 have had any changes made on the computer before the show?
    2. do you get an error message? If Yes, what is the full and exact error message?

    Method 1:
    I suggest you try the procedure described in the link and check.

    Windows wireless and wired network connection problems
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Method 2:
    If the problem persists, you can try to reset the Internet Protocol.

    How to reset the Protocol Internet (TCP/IP)
    http://support.Microsoft.com/kb/299357

    Hope this information is useful.

  • Printer network disconnected by Win - 7?

    I added that a Win PC - 7 XP network works with a shared network printer (HP Officejet Pro L7680), now the XP cannot go to the printer. Impressions are sitting in a queue. I downloaded the fresh drivers from HP for XP, (0), I uninstalled, ran CCleaner and reinstalled, but Setup fails when I try to add a printer in the finals?

    Works fine in Win - 7.
    What I'm missing here?

    I added that a Win PC - 7 XP network works with a shared network printer (HP Officejet Pro L7680), now the XP cannot go to the printer. Impressions are sitting in a queue. I downloaded the fresh drivers from HP for XP, (0), I uninstalled, ran CCleaner and reinstalled, but Setup fails when I try to add a printer in the finals?

    Works fine in Win - 7.
    What I'm missing here?

    Take your post literally, a "network printer" means a printer connected directly to your network with its own IP address (and not a "shared printer", which is directly connected to one of your computers and shared on the network).

    A problem that frequently occurs with printers network, especially when new devices are added to the network (for example, your new PC) while the printer is turned off, is that your router assigns a new IP address to the printer.  Your existing installation of the printer in most cases does not know the new IP address and then stacks of print jobs in the queue, waiting for a printer to connect to the IP address specified during the first installation of the printer.

    The way to avoid this problem is to configure the printer to have a static IP address, configure each computer to use this static IP address and forget it.

    To find the IP address of your printer, read the User Guide for the printer to determine how to print or display the network status report.

    If your printer is installed, right-click on its icon in the printers and Faxes folder, select properties and click on the Ports tab.  The port of your printer should be "HP Standard TCP/IP Port."  Do NOT click anywhere in the list of ports, but click on the button "Configure Port".  Compare the port with the port that you have found the printer itself.

    Some HP printer drivers include a box on the Configuration of the Port sheet who always says 'print to this device, even if its IP address changes.'  I have not found that it's reliable, but if you want to try it, you'll need determine 'Host name' the printer and that instead of a numeric IP address.  The guide of the user for more details.  Configure the printer to use a static IP address is much safer work.

    If you are still experiencing difficulties reinstalling your printer, see His Article first.  Be sure to follow step 4.  Generally, HP network printers are much easier to install using the installation 'complete' package from HP (the CD, for example) rather than simply downloading "driver only".  The only downside is that all the other garbage software HP is then installed also.

  • constant of disconnection

    WRT320N

    I bought this guy maybe about a month ago and it is constantly disconnecting. I my computer something dl or what I can do when I come back and its always disconnected and I have to disconnect and reconnect the router. getting pretty annoying? any ideas on how to help?

    I tried access to the content of my easylink advisor and I get an error message. I put in my drive maybe fix the error but unforunately I still get the same error. After reading your post, I realized that never again tried to open the Advisor.

    the error indicates that I need to install .net Framework: v2.0.50727

    any ideas on this one?

  • Wireless network disconnected randomly without reason on Windows 7

    I just bought a HP with Windows 7 computer.  I was able to set up a wireless network, but every now and then, it stops just work.  I have a Belkin Wireless N Router and an Atheros AR9285 802.11b/g/n WiFi Adapter.  It's as if it will work for awhile... then just completely stop without reason.  I have check the router and it shows the computer is always connected and there always have an Internet connection, but I had neither on my laptop.

    Have you tested with Windows Firewall disabled?  If you have third-party firewall, turn that off as well and test.

    I had the same problem and it was my Kaspersky Firewall that kept abandon the connection.

Maybe you are looking for

  • I was really hacked or blackmailed

    At the end of August in SM hotel in Las Vegas after having connected the local WiFi shortly my Macbook Air got hung with pop - up notice to immediately contact a number to phone for help. The popups were accompanied by piercing sound. OK, I contacted

  • I can not use iPhone 6s hotspot

    I can't use iPhone 6s via hotspot to access the internet I already install iTunes and my iTunes and the iPhone are the version lasted, but when I connect iPhone via wifi without success to connect or I try to connect via buletoot USB or failure, he c

  • Plugin Container causing the system to delay

    I've updated Firefox version 13.0 x and when I made my browsing is down the tubes. When I was getting errors on which script that I waited just nearly two minutes before I could go forward, or in some cases, type the next character.

  • Apple TV and YCbCr color space

    Sorry for my bad English. I want to know if we can expect from Apple TV to support as their previous versions YCbCr color space. Thank you Ivan

  • Undo the step not updated in the preview window or the composition.

    I have updated my legacy to later build 13.6. Whenever I press Ctrl + Z, or cancel, the compose window doesn't show updated preview updated. When I then try to purge option, then only it is updated.I have also cleared cache and database.Any solution