Continuous imaging using vision builder

Hello, I use NI 1744 and want to know how to get and record continuous images using Vision Builder. I am in a position to acquire and maintain a single image but cannot acquire continuous images.
Looking forward for your help.

Bürki,

You try to save the images continuously as a movie?  This is not supported in VBAI, however if you want to align continuous images individually you can try to change your pattern of State inspection to repeat your current inspection and the transition to the stage stop only after that your current inspection was conducted a defined number of times.

Tags: NI Hardware

Similar Questions

  • vehicle followed by using vision builder

    Can someone help me to follow a vehicle using vision builder?

    The object tracking feature to track multiple objects.

    To do exactly what is shown in the video, where the number of cars is variable, you must use the LabVIEW module and the development of the Vision to have more control over the creation of objects. (The limitation with Vision Builder AI, is that each object to track is associated with a follow-up session, so you should know in advance how many object you must follow, but VBAI to track multiple objects).

    The principle I described should be the same in LabVIEW: detect somehow the new car which comes within the field of vision and learn at this time where the object so that it can be followed. The prerequesite should be that you need to know where to detect them the car that comes in the field of vision. The difficult part of the application must define the area of interest of the new object that you want to track.

    The LabVIEW example for tracking of objects can be found here:

    C:\Program Files (x 86) \National Instruments\LabVIEW 2014\examples\Vision\Tracking\Object Tracking.vi

    Christophe

  • Which is faster a bit manipulation to the table or image using the vision

    I have to perform an operation on an image.  It involves the calculation of the new locations for the pixels for each pixel of the image.  Which is the fastest way to do it.  Manipulate the pixels as elements of the array for loops, or manipulate the pixels of an image using vision tools?

    Thank you.

    Hello

    If you can use vision tools to make the manipulation of pixels, it is much faster.

    Vladimir

  • Vision Builder - error creating LabVIEW Code

    Hello!

    I use Vision Builder 3.5 and LabVIEW 8.5.1. Vision Development module is also installed.

    I've built several routines inspection with the Vision Builder. Then I tried to create .vi-files. Then I hit tools-> Inspection migrating to LabVIEW...

    In the next box I select:

    1-version of LabVIEW: LabVIEW 8.5 - NEITHER Vision 8.5.0

    2 - the directory I want vi-files to be.

    The migration begins, but it is never finished. There is always the following error message:

    Error during creation of LabVIEW Code #3

    I have not found additional information about this error code. So maybe someone is able to help.

    Thanks in advance.

    It seems that the error occurs when you try to play a file which contains the parameters of control of that Vision Builder AI generates. This file may have been corrupted and Vision Builder AI fails to write correctly. I have attached a simple VI to determine where this file lives. Make sure that the file is not present before generating the code and that you have write access to this directory.

    Hope this helps,

    Brad

  • Migrating to labview vision Builder... Many VI

    Hello

    I use the latest version of labview and OR vision builder. Using Vision builder get the coordinates X and Y of the object in this area. I need to export this to labview. I tried going in "Migrating to labview. I created a new folder then I gave the name. When I click OK. It creates many VI. I need this in VI only. When I opened the "main.VI", I see that "make, start." When I check the block diagram. I couldn't find the programe I needed for it.

    Hope you understood my question.

    Can you please help me.

    Thanks in advance

    Another option, which could be used in conjunction with the API mentioned Christophe solution is to your X / Y values the variables that you update your VBAI inspection and then read in your code LV. Here's a tutorial on the use of shared variables to communicate the results to the LV of the VBAI:

    http://digital.NI.com/public.nsf/allkb/D492139A746F91A8862576E80051BBCE

    Here is a video showing how to use the API that Christophe has mentioned:

    http://zone.NI.com/WV/app/doc/p/ID/WV-2424

    Here's a video of the use of shared variables (demo shows using targets of the RT, but the same idea might work locally):

    http://zone.NI.com/WV/app/doc/p/ID/WV-2423

  • Cannot acquire image with NI1744 using the interface configuration of Vision Builder AI 2011: error-1073774588

    I use a 1744 OR with NI Vision Builder AI 2011. When I'm in the interface of the inspection, the camera will acquire and display an image. When I go to the configuration interface and try to put in place the stage of image acquisition, I have error-1073774588: the undefined error. I sometimes also 1074396159 error: not enough memory.

    Thank you for your repply Burrito.

    The problem was sloved and two errors went away after I formatted the camera and reinstalled the software on the camera.

  • NEITHER Vision Builder, acquire Images with fake delivery

    Hello world

    I am a student and I work as a trainee in a company, which produce helmets.

    To control the quality of helmets, there is a Webcam, wich take pictures of each helmet product.

    These Images are saved on the server. With the tool 'Simulate delivery', I can analyze the images, which are now in the folder.

    But when a new Image is the drop in the folder, I actually start the inspection again.

    How can I realize that NI Vision Builder always takes the current Images in the folder?

    Thank you very much for your help!

    Best regards

    Romain Menz

    Here is a simple example that illustrates how to dynamically read the images from a folder. Once the image has been retruned to VBAI, the image file is moved to a subfolder called Complete, so he has not read again the next time step is called. Step returns an error if there is not more images of the file type in the folder.

    Hope this helps,

    Brad

  • Create a continuous path using a base image? (son of barb e.g., vines, etc.)

    Is it possible to create a brush that makes a stroke which is a continuous image and not just a picture instantiated as usual?

    I saw brushes that already do it, I can't find information on how they do it.

    Here is one Example of

    Any help is appreciated!

    What you want would be very practical; You must put in a feature request. Until, however, you may be able to find a dynamic combination of brush that would give the same type of appearance. It must be a lot an articles out there on this.

  • Integration of third party Vision Builder C++?

    Hello
    A customer of ours uses NI Vision Builder in an application and questioned on the possibility of integrating our algorithms with her exclusive image processing.  Our code is a C/C++ library.

    I did some reading and downloaded the eval package, but it is not clear to me if this is allowed with the product.  The defined C API allow access to built-in functions, but I've not seen an obvious way for third party algorithms to access images or add new features.

    Vision Builder only supports it the algorithms or can developers add custom product image (in C/C++) processing algorithms?  Thank you.

    Hi eepdx,

    VBAI is not a contribution to the third-party code integrated directly in the script. And you are right about the C API.

    You can use the range of Vision Builder AI communications to communicate with the C++ application. Or you could translate your final VBAI script by LabVIEW code, then, LabVIEW can call a dll, so you could create a C++ application dll and call it from the LabVIEW code (it would be more complex).

    I hope this helps.

    Daniel C.

  • vision builder to labview migration

    Hello

    I have a project of vision. Pluggable VISION BUILDER pour image processing and the LabVIEW pour interfacing.

    My question is: how to call an inspection done by VISION BUILDER in the LabVIEW software.

    NB: I found in the Tools menu of VISION BUILDER a feature titled "Migrating to LabVIEW. but she could not be executed because I don't own

    the DEVOLEPMENT VISION MODULE. Have to buy another software OR (VISION DEVOLEPMENT MODULE) pour fix my problem? : smileysurprised:

    Thanks in advance

    Hello

    Vision Builder is provided with an ActiveX control that you can call from LabVIEW. You will find enclosed a few Directory promotion the in examples

    \

    The ActiveX component allows to control Vision Builder as you would you interface greengrocers. Once you have created your inspection in Vision Builder, you can use the ActiveX component to connect a Vision Builder of LabVIEW, open an inspection, execute, recover and display the image (you need not purchase the Vision Development Module pour it), and get the results of inspection and each step of the inspection.

    Hoping that this answer has your expectation

    Kind regards.

    Christophe

    OR R & D Vision

  • retrieve and record continuous images in labview

    Hello

    I use the NI 1744 smart camera to capture and record continuous images of a moving object. My smart camera is detected in MAX and made the seizure of an image. But when I use the attached file of VI in labview, the smart camera is not detected, only the webcam is detected and a video can be generated using the webcam. Please help me detect the NI 1744 smart camera. I will be grateful.

    Hello

    Your smartcam is not directly accessible from your PC because it is a remote device.

    Create a project in real time to access your camera.

    Have a look here: http://forums.ni.com/t5/Machine-Vision/Error-1074397145/m-p/535230/page/2?view=by_date_ascending

    Concerning

  • Result variation and inconsistency Ni Vision Builder AI

    I am currently using OR Vision Builder HAVE (2012) to analyze a series of images, and the preparation of appropriate inspections, I noticed that the results are not reproducible.  I am currently using various measures of analysis such as the color of the measure, number of pixels and the strength of edge and using the data logging feature.  The problem is that if I double-click on a stage as if to change, click on transfer to the next image, without changing anything, click OK, and then run all the tests again, I get different results.

    For things like the number of pixels that is relatively small - anywhere.0001 about 3 when it comes to figures around 200, but for the strength of edge especially these range from 10-20 at a time and sometimes he could find even an advantage that is then seen in over 40 years (and the edge resistance threshold is well below this value).  If this is inevitable then I can run many tests and average results, but it will be a lot of time because it also involves the steps wrong edition.

    Mainly, I would like to know if it is common and expected and if there is a known percentage error, or maybe I can change the configuration of the program in an attempt to overcome the problem?

    Thank you!

    The good news is that we have found what is the problem. When you change a step that uses a coordinate system and the current image is not the same as that used during the stage was originally set, the return on investment is transformed to the new position and step updates the settings used for this new position, when you press OK. Rounded the errors that occur when the transformed KING is caluclated, the new system of basic contact information you may not in the same positions of the KING. Kings use integers and therefore round us to the nearest integer, but it does not exactly the same positions as the coordinate system original base product. This may cause the new coordinate system of the step being out of up to 1 pixel and causes the return on investment deal with a slightly different part of the image

    For a given inspection/images, the results will not change unless you change the step that's important.

    If you change a step, but do not want to make changes, press Cancel instead of OK, and all settings will be the same.

    We will study a real fix for this problem that involves only update the coordinate system basis when the user redraws the return on investment, but the bad news is that this correction will not be in the version of Vision Builder AI we are about to go out.

    I'm sorry for this gap, and we plan to address in the future.

    Thank you

    Brad

  • default transition in vision Builder

    Hello

    I am a new user of Vision Builder AI 2011 and have a question about the transitions between States (default).

    In a testapplication I build for different features of Vision builder I want to create 3 States, each consisting of a series of tests. It works without problem.

    But the problem starts when I want to put an end to the test during one of the inspectstates does not pass. To do this, I added 3 (fault) specifies in which I put an overlay so that the reason for the "failure" becomes visible. The transition to these States 'fault' is changed so that the transition is only used when the above report fails. Each of the 'fail' states has a transition directly to the outcome.

    The problem I encounter is that, even when any of the tests fail, the program works always true all the other tests.

    Reason (I think), it's that I can't change the default transitions (ranging from inspectstate to inspectstate). And seeing that you cannot delete or change the default reports I can't find the solution to this problem.

    I've considered adding another transition between the inspectstates and to change this transition, but what to do with default transitions?

    Contribution to this issue would be greatly appreciated. I only started working with Vision Builder, but I see endless possibilities, if this problem is solved.

    Thank you

    Tom

    Hello

    After having a quick glance at your program, it seems that everything is OK, (as you did not provide the images, I just looked after the transitions).

    Your transitions are good, so if an error occurs in a processing status, go to the final State, and other States will not work.

    But what make you think that other States are good that the program doesn't run?

    You can run your sript in Setup mode after adding a delay in all States. You will then be able to see in schema view that pass are valid or not.

    Concerning

  • black bands - the problem of bandwidth - Vision Builder HAVE

    Hello

    I have a problem with an app where I anime shows Vision Builder 4 on 1 computer. Everything seems to go well until after some time (sometimes minutes, sometimes half an hour) I get horizontal black stripes on my images.

    I searched this forum and found many posts on this problem. However, I tried the various solutions that have been proposed and this does not seem to make a difference.

    Information:

    * 4 camera (Allied Manta G201C)

    * camera is triggered (rising edge) separately, but almost simultaneously.

    * PC: quadcore, 64-bit, Windows 7 64 bit system

    * Run-time Vision Builder 2012 license.

    * Programmed with Vision Builder HAVE 2012.

    * Switch: 1000 MB

    * Interface programmed in c# (receives images of the relevant info 4 programs and displays on the screen).

    Proven methods:

    * Sets the size of the packets to 1500 (even tried low size of package without improvement).

    * Set desired maximum bandwidth to 250 no improvement (was initially set at 1000 - we put it to 250 because there are 4 camera - even the 150 configuration does not seem to improve the situation.)

    * cursed a lot - but which did not help either.

    * Can use us a switch that does not fit our goal?

    * Our switch is placed with several engines around it (the closest on a meter away) and just behind a cabin of electricity in which there are several transformers. That reach our data?

    * Other suggestions?

    * Please let me know if you need additional information about this problem.

    We expect our customers to visit us the week next to see if we will be able to start production and we are currently under enormous time pressure (and stress). So, any help would be greatly appreciated.

    With sincere friendships.
    Tom


  • Control of a system of engine not to not 2 - axes of Vision Builder

    Hello

    is there a way to control 2 Motors step by step via Vision Builder?

    What are the components do I need?

    BR,

    Klaus

    Hello knuemm,

    There is no action, which allows to directly control the player. It depends on your hardware configuration, some engines step by step has a serial interface and also the device the vbai is running on other devices of movement has a digital input and some vbai devices have outputs digital that may be used for this.

    Fleeing a LabVIEW VBAI Inspection

    I followed the smartcam NOR control pilot Motion

    You can also create steps for the VBAI to run LabVIEW code

    NEITHER Vision Builder HAVE Development Toolkit

Maybe you are looking for

  • Change the device where the verification code is sent

    I'm changing my password Apple ID, but I forgot the answers to my security questions that I need to change the password. I am connected to iforgot.apple.com but the verification code is sent to an old iPod Touch 4th generation which I did more. Is th

  • Re: Tecra M9 - 15I - HDD that upgrade?

    I think of upgrading my laptop HARD drive. I seek through my options and don't know whether to go for a HARD disk with a rpm of 5400 or 7200. Read information from the manufactureres, a 7200 RPM hard drives are usually better. But no one knows how th

  • Menu, Nav, bookmarks and toolbars are not displayed.

    Here is a screenshot of Firefox on my computer - http://i.imgur.com/meaTv.jpg http://i.imgur.com/meaTv.jpg http://i.imgur.com/meaTv.jpg everything up. No bookmarks bar, navigation, toolbars, the bar nothing. I tried customize the layout and after tha

  • Satellite U300-111: Linux FreeBSD 6.3 X 11 issue

    Hello On my Toshiba U300-111, I installed FreeBSD 6.3. In sysinstall I choice X Windows must be installed as well. After the installation when I tried 'startx', it gave me an error. I wonder has anyone else tried to install FreeBSD on their Toshiba l

  • LapDock screen resolution?

    Surprisingly, no where on the bike site, site of AT & T or anywhere else find the number of actual pixels of the screen. I try to encode movies that will play well in fullscreen in an entertainment center, but I need to know the maximum width before