Continuous printing and HP

Similar Questions

• I have a HP9050 printer and continue to receive an error 59.10 on the main screen.

  I replaced the cartridge and the DC controller and the Assembly of the main engine, but it did not help.

  any ideas?

  Thank you!!

  Hi Jankster2,

  Generally, an 59.le xx error message is due to a temporary printing error occurred and requires you to restart the printer. The 59 error is related to a main engine failure. There are a few parts that you will need to look below.

  1. the cables on the DC controller PCA

  2. run the test of the Service and give me the code

  Service test verifies that the print engine is working properly. This test is very useful for

  isolate the printer problems. The test can be performed with this attached paper handling accessories,

  but it will not activate the engine accessories, switches or sensors.

  To perform a service test

  1 . turn off the printer.

  2 . make sure that the printer paper path is clear of all the media, and that the left front and right

  the doors are closed.

  3 . open the tray 2 and tray 3.

  4 . turn on the printer, and when the printer is ready, press to open the menus.

  5 . use or to scroll to the DEVICE you want to CONFIGURE, and then press.

  6 . use or to scroll to the DIAGNOSTICS, then press.

  7 . use or for SERVICE TEST highlight, and then press. The service test can take up to two

  minutes to complete. The TEST EXECUTION SERVICE message on the control panel.

  8 when the test is finished, the message SERVICE TEST PASSED appears on the Control Panel, or

  up to five sets of four-digit numbers are displayed on the control panel. If none of the anomalies have been identified,

  (0000 0000 0000 0000 0000) appears. If abnormalities have been identified, the four-digit codes

  appears in parentheses (0101 0111 0132 0000 0000). Note these codes

  3. it might be Assembly of registration or the main engine causing the blockage.

  If it does not always help I'd consider having a HP authorized service technician come out and diagnose the error.

• Toshiba e-Studio 3040c continues printing from other sources

  Hello together

  In our society, we have a Toshiba E-Studio 3040c next to other printers.

  It prints and basically works well, but we have the issue that if a source document is empty, it continues printing from other sources, even if there is another paper out there.

  The only point in the Web interface with: "Change the paper source automatically" is set to NO then it theoretically it should continue printing.

  Any suggestions I can try next?

  Thank you for your adived

  Erik

  You solved this problem?
  I m asking because this community forum talking about Toshiba digital products like laptops, tablets, and TVs
  I doubt that you will find here a few specialists printer.

  However, I recommend you to check this page from Toshiba for printer product information and specifications
  https://electronicimaging.Toshiba-Europe.com/

• Firefox will not print on my HP PSC 750 printer and loses all formatting when you try to print to the printer Brother HL-5240

  I have no problem with one of my printers when printing 11.7 before or IE 6.0.2800.1106 but cannot print from Firefox 3.6.13 (or earlier).
  When you try to print to the HP PSC 750 inkjet printer, a "Print" dialog box appears, showing the title: xyz and a progress meter showing 100%, but it's be covered almost immediately by a second dialog box stating "an unknown error has occurred while printing" and, even if the continuous printer saying 'impression', no printing is taking place.

  When you try to print to the Brother HL-5240 laser printer, printing will take place, but all formatting is lost and what comes out is a block of text unintelligible running.

  What can / should I do to get Firefox to print correctly on my two printers?

  1. print.print_printer reappears after printing something. This pref is the last printer used, so when you reset the prefs it does not appear until you print something.

  2. that your problem with printer HP reappeared quickly, try a new profile.
  
  http://KB.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows

  3. with regard to the preferences for the old printers, if reset you these Pref they don't come back (assuming that you do not select accidentally printers or printer drivers are uninstalled).

• DJ3070 B611a: print and scan the doctor

  my printer HP DJ3070 B611a just stopped to connect to my network home. Windows Help (7/64) has not solved, so excited printing HP and doctor Scan. Upgrade of downloaded software, which gave (after download, install, a lot of time) gave an installation error that has not explained. Somewhere on this site I found that I had to uninstall the old software before installing upgrades. question 1: why P & S doctor can only him before the upgrade? Many programs can and do. Or at least: tell me to do.

  After that I discovered, I followed the instructions (very many steps and options) on the removal of the old software, any software called HP..., but it did not work. I tried to install the upgrade, but not over and over again. Would take a lot of time, because doctor & pajaud (> 50 MB) checks, downloads and try to install again, although he's done before. 2nd question: why he doesn't download / upgrade is already there?

  Therefore, no connection to my home network. After connection with a cable my laptop seems to recognize the printer again, although it does not show on the printers screen in Windows. And to be printed, but not for scanning.

  question 3: If, for the print connection is ok, what can be wrong with scanning (and why is this not the same connection)?

  So beware before you use the doctor: it does not help you and does not explain or for me does not clearly what he wants me to or exactly where to look.

  Is do not support my first experience with HP software problems, stable and updates: far from average. Disappointing for a leader in the software.

  Hi HermPack,

  Thank you very much for your answers!

  The name of the software of the doctor & pajaud, according to me, is HPPSdr.exe. In the meantime, to continue troubleshooting, please try the following steps in the following order:

  • Uninstall the software. Uninstalling the printer software.
  • Clean boot the computer. How to perform a boot in Windows.
  • Disable all Antivirus programs. Disable Antivirus software.
  • Disable all firewall programs. Turn Windows Firewall on or off.
  • Create a new user account. Management of accounts of users and connections (Windows 7).
  • Reinstall using the printer HP install wizard for Windows.

  Then run the HP print and Scan Doctor, once more to check that everything works.

  I hope that these measures are useful!

  "Please click the Thumbs up icon below to thank me for having responded."

• printer, continuous printing to stop in half way through

  printer, continuous printing to stop in half way through

  Hello

  1 are there any changes or updates made on the computer?

  2. what operating system is installed on the computer?

  3. do you get an error message? If Yes, what is the full and exact error message?

  Method 1:

  I suggest to see the link and try to run the troubleshooter.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• Canon Pixma iP1500 printer and it connect not gives an error code 20

  I have a canon Pixma iP1500 printer and it does not connect gives an error code 20?

  Hello

  1. If it works much earlier?

  2. did you make any changes before this problem?

  3. What is the exact message you received?

  I suggest to go through these steps and check.

  Method 1:

  This is due to the UAC. Disable UAC will help because UAC prompts the user the permission to continue, the time required to get the question and answer that cause the printer to turn it off.

  If you do not want to activate UAC you can call EnablePrinter when the capture of the EnablePre() event generated by the driver.

  Note: User Account Control (UAC) can help you to prevent your computer from unauthorized changes. It works by asking permission when a task requires administrative rights, such as installing software or changing settings affecting other users. We do not recommend disable user account control. If you turn it off, you must reactivate as soon as possible.

  Method 2:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 3:

  Uninstall the printer driver, download the latest driver on the manufacturer's website, install on your computer and check.

  Step 1: you can download the latest driver from the link below http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_ip_series/pixma_ip1500#DriversAndSoftware

  Step 2: Uninstall the device from Device Manager driver.

  a. right-click on the icon my computer

  b. Select manage from the menu.

  c. Select Device Manager in system tools that are listed in the resulting display.

  d. right-click on the device.

  e. click on the driver tab.

  f. click on uninstall.

  g. restart the computer

  Step 3: Installed the downloaded printer driver and check out them.

• error 0x000000c1 with a canon lbp 6300dn printer and Vista Home Premium

  I have a Vista Home Premium that I try to install a canon lbp 6300dn printer on a network.  It gives me the error 0x000000c1. I got the correct driver of canon but continue to get this error? can you help me?

  It is an unrecoverable Windows, usually called error message Stop, bug verification, or more commonly the blue screen of death (BSoD).  Not a Setup error.

  You can try to install over the previous installation.

  If you can get the system for more than a few minutes or you can use safe mode, try to delete the last installed application software or driver.
   
  For the withdrawal of an application:
  1. click on start, Panel, then programs and features.
  2 Select the software associated with the printer, and select uninstall.
   
  To uninstall the driver:
  1. go into the Device Manager
  Open the Device Manager
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Device-Manager

  2. find the printer driver, do a right click Uninstall.
  3. also in the Control Panel, printers, right-click on the printer and click on delete.

  Now try to install your printer with the latest drivers available on the Support site of the manufacturer.
  http://www.USA.Canon.com/Cusa/support

  Your Type of product: consumer Home & Office
  Family of products: Printers & Multifunction
  Series of products: image CLASS series

  See also these:
  Bug Check 0xC1: SPECIAL_POOL_DETECTED_MEMORY_CORRUPTION
  http://msdn.Microsoft.com/en-us/library/Windows/hardware/ff560183 (v = vs. 85) .aspx

  SPECIAL_POOL_DETECTED_MEMORY...
  STOP: 0X000000C1
  http://www.faultwire.com/solutions-fatal_error/SPECIAL_POOL_DETECTED_MEMORY_CORRUPTION-0x000000C1-* 1194.html? = date order

• Scanner does not work on my Hp Printer and I can't find a way to see my ink level

  Hello!  I uninstalled HP Support Assistant, did an update of Windows, installed on official site, and still I can not scan from my printer (you had to make a shortcut to scan from my computer), and I do not know my ink level.

  Any ideas on how I can see my ink level?

  Any ideas on how I can scan (even if it's a low priority because I did this work around)

  I go back to the site of HP and HPSA (ensuring that everything is updated), but I don't see that the HP Digital Imaging Monitor icon is msising and HPSA advised me a custom installation and to include that when installing.  It is the icon/program to see my ink level.  But I can't seem to get there. Not an option for installation.

  Any other ideas?

  Thank you!

  Hi linsjean,

  I see that you have lost the ability to use the HP software to scan and check the ink levels. You can continue scanning as you are now, simply download and install HP Print and Scan doctor to check your ink level, or you could perform a full uninstall and reinstall.

  Click here to download and run the utility > HP print and Scan Doctor

  

  Or you can use the steps below to complete uninstallation and reinstallation;

  1. Hold down the Windows Logo key () on the keyboard and the 'R' to open the dialog box run, type %temp%
  2. Delete all files and folders in the temp folder. Choose Skip if all pop ups seem to say all files cannot be deleted
  3. Download the software and choose Save as, save to desktop > click here, choose your operating system, click Next, select the product software driver installation and download your software.
  4. After downloading software and extracts, reopen the temp folder, use the instructions in step 1.
  5. Locate and open the folder starting with 7z (example: 7zS2356)
  6. Open the folder Util
     
  7. The CCC folder
  8. If you have a computer HP run the L3uninstall.exe. If you have an non HP computer run the L4uninstall.exe
  9. Once the uninstall is complete, reboot the computer
  10. Follow these steps to reset the registry settings and options for Windows Installer.

• To stop continuous print spooler

  Using Vista Home Premium 64-bit.  Print spooler continues to stop.  Attempts to restart indicate he started, but closes immediately after an attempt to print or the beginning never happened

  Hello

  Don't forget to check with the manufacturer of your printer Support and forums for known and possibly most recent problems
  drivers.

  Check chan seen message here - one of the highest.

  fixed spooler subsystem app stopped working
  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

  ===================================

  If the above didn't help:

  Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
  the latest driver).

  Check Mr. Fixits here and if you use the other methods go back and try again later.

  Problems of print and error - a Mr Fixit of printing
  http://support.Microsoft.com/GP/printing_problems

  Solve printer problems - a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx

  ------------------------------------------------------
  Logon as administrator

  Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN

  You can copy and paste each line except those brackets and press ENTER after each.

  net stop Spooler

  (echo suppression of all print jobs)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  del/q %SystemRoot%\system32\spool\printers\*.*

  net start Spooler

  (sound Done!)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  Another way
  http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/

  Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
  http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspx

  If you use Control Panel - Classic - printers

  Try after unplugging your printer if necessary.
  -------------------------------------------------------------

  Also check the spooler print and its dependencies and addictions Service.

  Print Spooler service
  http://www.blackviper.com/WinVista/services/Print_Spooler.htm

  How difficulty Windows Vista print spooler starts do not
  http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html

  ------------------------------------------------------------

  Check this thread if necessary - to stop and erase the spooler

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a15779d6-ac0d-42FD-9Ac2-a1da241ea19f/

  and here
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/58b54fa9-cf6f-40F7-90b2-8093c6777493

  ------------------------------------------------------
  Clean the General corruption and repair or replace the damaged/missing files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  CheckDisk (chkdsk) runs at startup.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Try to reinstall the printer and will not install due to not having Admin rights

  original title: Instalation printer

  Try to reinstall the printer and will not install due to not having Admin rights. I am the administrator,

  How can I continue?

  Thank you

  Right click on the printer software setup.exe, etc > run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• Continues printing additional copies not necessary that a single copy.

  Photosmart C7280 with WIN7. When wishing to print a copy of a listing of the printer continues to print additional copies after the first copy despite having been fixed for only one copy. Everyone knows this product or ideas. Have uninstalled and reinstalled the printer and the software but no change.

  Hi Shane,

  I did as you suggested and the results were the same.

  I uninstalled the printer and reinstalled.

  Everything is OK now.

  Thanks a lot for your help.

  Kind regards

  Mike

• 8600 premium print and then gives the error message that it cannot print the document that it just printed.

  It isn't really a problem, just a nuisance.

  Last week I printed several documents from PDF files and print documents.  Once printing has been completed, an error message would be displayed on my laptop that the printer cannot print the document.  I've ignored the warnings and continued, and then the printer would print the document again.  I found that if I clicked on the error message, printing in double stop.

  Since then, whenever I don't print from any program (MS Office, Firefox, Chrome, IE, etc), I still get the same message if the end of the print document.

  Just a nuisance, but if I forgot to point out the error, the doc print again without error message after the second printiing...

  I noticed that the queue, regardless of the size of the document, always freezes on the last page to print before closing.

  I turned and turn it back on and reset the connection to a static IP address for the printer wireless...

  Hello DRS1966,

  Yes, I can understand the frustration of getting an error once printed of your document. I'm glad that's not interfering with your documents but would like to try and get rid of it. Please run the HP Print and Scan Doctor- designed by HP to provide users with troubleshooting and problem-solving features needed to solve many common problems encountered with HP print and scan products related to Windows computers.

  Please let me know if it detects errors, or that it cures the problem. I'll watch for your reply.

  Thank you

• my printer and computer are both connected to my wireless network, but I can't print documents

  I have a HP Photosmart 6180 and am using Windows Vista.  Both the printer and the computer indicate that they are connected to my wireless network and my computer shows my printer on the network.  When I try to print a document from my computer, nothing prints and printing on my computer says a mistake of the printer.  The printer itself works fine and HP diagnostics indicate that everything is ok.  Any suggestions?

  OK, go to start > Control Panel > printers and delete all instances of the printer.

  Next:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing. Get his IP address for a network Test printed on the front of the printer.
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• Photosmart 5510 not printing and noises when toggled or asked to print?

  About 6 months ago, we purchased our printer HP Photosmart 5510 alongside our Touchsmart computer, and so far, both work fine.

  However, there are a few weeks at random, when I sent a document to print, the printer started making a very loud noise, sounding almost as if he was that something stuck in the back there. Only to make the noise stop, I cancelled the printing and has turned off, which again triggers intense noise. This back on once again, he made the same noise and, before moving on to the usual display a notice on the monitor of printer flashed by saying that the device had extinguished itself incorrectly.

  It lasts for a few weeks now, and after having scoured your Web site for all the details, I couldn't find anything on this issue. After detecting that other factors may have come into it, I watched some of your videos on how to fix etc. paper jams. After pulling some paper in the back, I thought the culprit of all this, the message on the monitor said he had a 'ink cartridge problem' or could not detect the paper, even if we just replaced the ink and I have to reload the paper. I watched the videos of these two problems troubleshooting and tried 20 seconds thing etc, but nothing worked.

  Really, I'm so frustrated and I would like a little help from a very kind person out there?

  

  Hey mollycat,

  It seems that there is a problem with the power of the printer mechanism paper.  If the unit was loud noises, then it might be a part out of alignment or a piece of paper caught in the unit.  However, you mentioned the continuation of the measures is stuck, remove the paper, and now the printer gives error ink system.

  I will provide documentation of troubleshooting below for the two issues, but if these steps don't erase the question then I would advise to contact HP Technical Support on this printer.  Is it is only 6 months old, then it would still be under warranty by the original manufacturer.

  An "Out of paper" message on the control panel and the all-in-one doesn't pick up paper

  An alphanumeric Code (example: ' 0 x 'r' C2...) ") or 'Ink system failure' Error Message is displayed on the front panel when printing

  To contact HP Technical Support: contact HP worldwide | HP

  Hope this helps,

  Jason