Control of start burn failure is p2pp

Hi, I have tried to reset my laptop to factory setting and used 3 recovery CD that came with my laptop. After the recovery is complete. I get an error saying P2PP BurnBoot verification failed.

I am not able to connect to windowns and my phone is idel lying. Can you please help me get this resolved.

Having just suffered from this problem on two of my own laptops, it seems that the way to solve it is documented in this thread:

http://h30434.www3.HP.com/T5/notebook-operating-systems-e-g-Windows-8-and-software/restoration-failed-P2PP-burnboot-check/m-p/2562175#M133274

In short: startup in the BIOS loading the laptop by pressing F10 - change the date of 2013 for 2012 and then try to run the recovery again. When it is finished successfully and loads in Windows, you must then install the patch/update detailed in the thread above to make sure that you can perform successful recoveries in the future.

Hope that helps.

Tags: Notebooks

Similar Questions

  • HP Pavilion 400-434 Office: intelligent control of hard disk: failure

    Hello

    It all started when the computer would go blank right after startup, the HP logo would come upward, then 'auto repair preparation", more... Just empty. After reading the forums online, I did all the possible troubleshooting steps and at the end I did the SMART test... the result was:

    Verification of the processor: past

    Intelligent control of hard disk: failure

    Failure ID: RGD7MK-7HV7RC-9XJ16K-60BB03

    After obtaining these results, when I turn on the computer, it gives me a blue screen saying: drive SMART 1 error (301) and told me to test once again, that I did and got the same result as above.

    Here is some info from the computer:

    Model: HP Pavilion slimline 400-434

    Processor type: pentium (R) of the Intel (R) J2900 @2. 41 GHz

    Thanks for your help!

    Hi there @Brugalgirl

    Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that your computer does not start successfully, and you found a Smart Drive 301 error code. I'm happy to help you with this.

    I checked the ID of the failure, you've posted and verifies that the error. Unfortunately, this means that your hard drive needs to be replaced.  In view of the fact that the system does not boot, it is likely that the hard drive is completely unreadable, but depending on what you have on this subject, it may be worth your while to check with a local computer service shop and see if they can help to recover data from your hard drive.

    If your system is relatively new and may be covered by the warranty, or if you wish to fix with HP for the guarantee system, you can call in hotline to make these arrangements. In this case, please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
    http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

    Otherwise you can look at a replacement hard drive yourself. If you have a set of recovery media, then you already have a factory image HP, which allows you to put in place a new hard drive with your original operating system. If is no longer, you have a set or did not have a set of recovery media, so you can see if there are not yet available for your model.

    HP computers - get HP recovery disks or HP USB recovery disc

    Let me know if you need help most. If it solves your problem, please mark this message as a solution.

  • In Windows Media Player, my light "Start burn" would not light after dragging the songs on my playlist

    In Windows Media Player, my light "Start burn" would not light after dragging the songs on my playlist, he said only "Connect burner and restart". I have already burned a music CD "RW", why he said burner "connect"? The burner is already installed? I tried the "Device Manager" thing wasn't working, thank you for your help. "

    Hello

    1. have you installed any third-party DVD burning software on the computer?
    2. could you give us the exact error message?

    Method 1.
    If you have installed a third-party software CD burning remove it and then try to burn the disc and check. Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Method 2.
    a. Click Start and type cmd into the search bar and press ENTER.
    b. in the type guest following command press ENTER.
       WMP.dll regsvr32.exe.
    c. close the command prompt and start Windows Media Player and check.

    Method 3.

    You can re-create the database of Windows Media Player and see if that fixes the problem.

    Stage i: To resolve this problem, delete the Windows Media Player database. To do this, follow these steps:

    a. exit Windows Media Player.
    b. Click Start, type %LOCALAPPDATA%\Microsoft\Media Player and then click OK.
    c. Select all files in the folder and then click on Delete on the file menu.
    Note: You don't have to remove the folders that are in this folder.
    d. restart Windows Media Player.
    Note Windows Media Player automatically rebuilds the database.

    Stage II: If this does not resolve the problem, disable the Windows Media Player database cache files. To do this, follow these steps:

    a. exit Windows Media Player.
    b. Click Start, type % LOCALAPPDATA%\Microsoft and then click OK.
    c. Select the Media Player folder, and then click on Delete on the file menu.
    d. restart Windows Media Player.
    Note Windows Media Player automatically rebuilds the database.

    I hope this helps.

  • Why do some executable programs require Windows Vista user account control to start, while others do not?

    For example, Iobit Advanced System Care 6 requires user account control to start, while none of the programs Microsoft Office requires user account control to start, but they are all executables (*.exe).  Why?

    EXE files may have a small text file embedded in them that controls this behavior (and other). A file called programname.manifest in the same folder can do it too, but one stand-alone exe substitute manifests (vista and later).

    Here is one that requires the Admin run and also uses 6 worm of the common controls.



    <>
    version = "1.0.0.0".
    "" processorArchitecture = "*".
    name = "DFT".
    Type = "win32".
    />
    Unicode text editor

       
            <>
    Type = "win32".
    name = "Microsoft.Windows.Common - controls.
    version = "6.0.0.0.
    "" processorArchitecture = "*".
    publicKeyToken = "6595b64144ccf1df."
    "" Language = "*".
    />
       



       
           
                <>
    Level = "requireAdministrator".
    uiAccess = "false".
    />
           

       


  • Intel graphics and Media Control Panel starts whenever I start

    I use Windows 7. This control panel starts every time that I start and I have to manually close the screen. How can I stop this from happening? This just started to happen after I replaced my hard drive.

    Hello

    Look in the control panel to see if there is an option to run at Windows startup
    and if so, uncheck this option.

    You may need to check with the support of Intel and Forums.

    Intel - Support
    http://www.Intel.com/p/en_US/support
    Intel - community and Forums
    http://www.Intel.com/content/www/us/en/blogs-communities-social.html

    =============================================

    This can help:

    How to change, add or remove startup programs in Windows 7
    http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

    Autoruns - free - see what programs are configured so that it starts automatically when your
    system boots and you log in. Autoruns is also the full list of registry and files
    locations where applications can configure start automatic settings.
    http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Some of the Menus Adobe Premiere element cause DVD burning failures?

    Some of the Adobe Menus cause DVD burning failures?   What should have been a project of 10 minutes for a small 4 minute video took hours as burning DVDs stopped at 4% and then gave a message of "something has prevented completion in progress DVD burning".  I could finally solve it down for the Menu template, and when an audio clip looping has been added.  The Menu was built for an audio clip loop, but when I removed it the fine burned DVD.

    Since my last post, I checked that my drivers are up to date.   Driver updates were made to the display card Intel HD 4600 Graphics and Chipset Intel 8 series/C220 family SATA AHCI Controller.

    I created a new project and changed the flow of work to remove the check mark from selection to 'Add Menu markers automatically for me'.   When the menu has been selected and displayed, only the main Menu was to confirm that I didn't remove the Menu scenes.   At this point, I finished the remaining workflow and tried to burn on DVD using the stated parameters previously.   However, it had the same failed result.

    I went then to the path of Premiere Elements menu bar: Edit > Preferences > General

    The option "use hardware acceleration (works on Intel HD Graphics 2000 and higher)" has been selected.  I unchecked this option and clicked on the OK"" button.   I then tried to burn DVD with DVD NTSC_Widescreen_Dolby preset.

    Success!   The DVD was burned and confirmed to work in older DVD player (AVCHD burning earlier disk did not work in older DVD player, but worked in a new Blu - Ray player).

    It seems that the "use hardware acceleration" option preferred default was the problem in the prevention of burning DVDs.

    A.T. Romano thanks for your quick response and help to solve this problem.

  • HP Pavilion G6: INTELLIGENT control of hard drive failure

    Model: HP Pavilion Notebook PC g6

    PROD ID: LN220EA #ABV

    Warranty start date: 27/05/2011

    Smart Check: FAILURE

    FAILURE ID: 9C1G7F-5LK7KD-XD015G - 608L 03

    Hard drive 1

    Test drive: FAILURE

    What is my problem?

    Whenever you get an error message with 24 characters alphanumeric numbers indicating that the hard drive needs to be replaced to solve the problem

    Could be due to the Application or a driver conflict, virus issues, corruptions of files due to incompatible applications, improper stops, update failures due to conflicts, mounted sudden power sudden, so portable falls etc...

    HP will offer a replacement HDD if the laptop warranty is Active, otherwise you can buy a SATA hard drive in a nearby retail store

    Please make sure that you get at least equal as long as the original one in order to use recovery disks. If you need you can buy a bigger, but not smaller hard drive capacity. For example, if you have a 500 GB hard drive you can improve it to 750 GB hard drive, but not 320 GB hard drive

    Please try the troubleshooting below indicated once the steps:
    Step 01. Remove the battery and unplug the power adapter AC.
    Step 02. Press and hold the power button for more than 30 seconds
    Step 03. Plug the AC power adapter / (leave the battery for now)
    Step 04. Press the power button and check if the unit is operating normally

    If the steps listed above is not enough, then you can try reinstalling the hard disk on your laptop

    If the problem persists again please contact HP if your HP laptop is under warranty, HP could replace the hard drive and provide recovery media to restore the operating system to factory after the replacement (if you have not yet created recovery disks/USB support)

    Note: Back up all personal data on an external drive if possible. Otherwise, you can connect the HDD defective via SATA Adapter USB with another PC or a PC even after replacing the HARD drive & put in place of the operating system and try to copy / retrieve files.

    Please click on the link in order to identify, prevent, diagnose & recover against any failure to drive on HP Portable Hard Drives & Solid State Drives:
    http://h10032.www1.HP.com/CTG/manual/c02876562.PDF

    Please check your warranty for laptop to check the status and order a new hard drive

    Hope this helps, for other queries in response to the post and feel free to join us again

    * Click on the star of CONGRATULATIONS on the left to say thank you *.

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

    Thank you
    K N R K
    Although I am an employee of HP, I speak for myself and not for HP

  • Pavilion dv7-6b32us: that means start diagnosis failure ID QC6C51-5R67HW-QFPH4K-402BO3?

    HP Pavilion dv7-6b32us laptop

    Start-up took like 15 minutes so I did some diagnostics and received a failure id QC6C51-5R67HW-QFPH4K-402BO3

    The operating system could be zero, but not sure.

    What is the error? Can't seem to find anything online. Very much appreciate your help.

    Thank you!

    It seems that the hard drive has failed/is a failure and should be replaced. If you are still in warranty HP will send a replacement. If this is not the case, a laptop SATA hard detail can be used. Just be sure to get a quality at least equal the original in order to use recovery disks. It may be big, but not small ability more. For example if you have a 500 GB hard drive you can use a 750 GB hard drive, but not a 320 GB hard drive.

  • Always start with FAILURE in Windows safe MODE

    Hi guys,.

    My computer still starts in safe mode. I tried pressing F8 before the logo appears and select START WINDOWS NORMALLY, but he's still in safe MODE. I can not use certain features and can not install updates. Help, please.

    sgs1973

    Hi sgs1973,

    Check the System Configuration to make sure that your computer is not configured so that it starts in Mode without failure.  To do this, try the following steps:

    1. click on Start.

    2. type msconfig. (This will bring up the System Configuration window.)

    3. go to the Startup tab.

    4. If selected, remove the ICT start-up secure.

    5. click apply and then OK.

    6. restart your computer.

    Dena
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • "Start burn" option grayed out am trying to burn a CD

    Original title: try to burn a cd

    I dragged all songs to burn the list but the burn 'start' will not highlight so when I push it, it does nothing. How do I get this to burn?

    Hi MirandaEdwards,

    SE for focus in the right direction, please provide the following details:

    (1) what program are you using to burn the CDs\DVDs?

    (2) have you checked with different CDs\DVDs?

    Run the fixit available in the below and check if that makes a difference

    Your CD or DVD drive cannot read or write media

    http://support.Microsoft.com/mats/cd_dvd_drive_problems

    You might want to know

    Burn a CD or DVD in Windows Media Player: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows-Vista/burn-a-CD-or-DVD-in-Windows-Media-Player-frequently-asked-questions

  • After installation of the parental control my Start Menu will not open

    I have recently installed Windows live family safety on my computer. After I've set up and he began to monitor user accounts, I found that the start menu will not open and when you navigate in Explorer, records that contain a large amount of files I can't navigate to files that lie near the bottom, as it keeps jumping to the top of the page.

    It is without doubt parental control that is causing the problem as the uninstall it sorts the problem. I ran SFC/scannow, a cmd in normall, and safe mode prompt and it doesn't find any errors

    . I had this same problem when I got the laptop in November and a successful to fall on a difficulty at the time (to install the resource from Dell that CD somehow fixed?), but now that either doesn't work or it was a coincidence that the problem has been resolved at the same time, it seemed however to solve the problem on some laptops that I worked at the time.

    I had to reset the laptop back to factory settings (ironically due to a system error that prevented the family of work safety!) I also tried a replair nothing works facility. When I installed Essentials I selected only parental controls must be installed.

    I am now at my wits end, I do not understand how a piece of Windows software is make a significantly Windows operating system!

    The installer I used was version 15.4.3555.308, is there a more up-to-date this solve the problem? Any help would be greatly appreciated!

    Hello

    The question you have posted is related to Windows live family safety and would be better suited to the Windows Live community. Please visit the link below in order to send the request in Windows Live forums for assistance.

    http://windowslivehelp.com/product.aspx?ProductID=4

    Hope this information is useful.

  • PE9 burn failure at 95% causes the whole computer crash

    Hi - I hope someone can help.

    I'm puttig clips set of mobile phones and various other devices in the first year of the life of babies, it includes audio tracks on the line of the soundtrack as well as the audio and video on track 1. I have also included a pan & zoom slide show of images and the total length is approximately 1hr20mins.

    I don't know what the problem is, but after that the disc menus (there are 4) were all coded, the program gets to 95% and then hangs, but is not just down to the program, in fact, it blocks my whole system by which I can't use my mouse or keyboard to close anything.

    Last week the system worked perfectly and I tried to save the entire movie as an mpeg on my computer that worked perfectly, but there is something preventing the burning at the end.

    I use a Dell XPS 17 with processor intel core i5, drives (C and D) with 1 TB of total RAM. I use a Nvidia graphics card and have RealTek HD audio. (not sure if you need this or if there are good things to tell you!)

    Help, please!

    You probably have a number of questions which are an overload of the program. It is also possible that you don't have enough clean, freshly defragmented space on your drives C and D. Even if these drives are huge, fragmentation to prevent the Premiere Elements entering the contiguous space he needs. You work a) an exceptionally huge for a DVD video (DVD can contain about 70 minutes of video), b) you may be using unnecessary large photos (see below) that can stifle the program and c) you say not where your video is coming, but Premiere Elements must work much harder on the video that is not miniDV, HDV or AVCHD - these are all combining in a collapse of the program.

    First of all, when you set up your Premiere Elements project, including project settings have you selected? You have made this setting corresponds precisely to your video footage? If so, you should see no red line above the clips in your timeline before add them effects. This is the case in your project?

    Second, have you ensured that your photos are not larger than 1000 x 750 pixels of size? Photos directly from a device using photo (some of which can be several times video resolution) are the main cause of starter program.

    You have made your timeline (press enter) whenever you see red lines above your clips on the timeline? If your timeline is rendered (at the Tower of red green lines) your program will perform more effectively and you will have less problems with transcoding your DVD. But even this does not however resolve the questions listed above.

  • The process of Windows Service Host: stop start update failure

    Running 32-bit Vista Home Premium SP2

    Description
    A Windows Update was not installing correctly. Send the following information to Microsoft can help improve the software.

    Signature of the problem
    Problem event name: WindowsUpdateFailure
    ClientVersion: 7.4.7600.226
    Win32HResult: 800f0816
    UpdateId: 4585715C-92BD-4D61-9F64-88AD70A7936D
    Scenario: install
    SourceId: 101
    Environment: unmanaged
    The system version: 6.0.6002.2.2.0.768.3
    Locale ID: 2057

    Additional information about the problem
    Bucket ID: 1563453098

    Searched for fix and it could not find a. When I put on, I must go through a restoration of the system to an earlier point. At this point, the error says "a patch has stopped windows to start successfully. I have not run any firewall / anti virus other than the defender and Security Essentials.

    Applications, (Norton and McAfee) are known to not uninstall (or upgraded) themselves.

    1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

    2. close all open applications (that is, anything with an icon on the taskbar).

    3. click right on the file saved in #1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

    4. open Internet Explorer (only) to http://support.microsoft.com/kb/923737 & run the difficulty.

    5. open Internet Explorer (only) to http://support.microsoft.com/kb/971058 & run that set it by DEFAULT and modes and AGGRESSIVE. [1]

    6. restart a last time & test.

    ~~~~~~~~~~~~~~~~~~~~~~~~
    [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not the list of installed updates.

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • XP home bsod cannot start without failure or last known configuration mode, do not have a startup disk or any what CD of xp

    a xp home edition with no update at all and no internet connection, tried to install service pack 2, but he said he could not copy one or two files and collapsed, now I can't on, I get a blue screen of death with the error message 0 x 00000071, tried all modes of security start and know last config , but they all lead me to the same bsod

    Hello

    I suggest you to follow these steps and check if that helps.

    Method 1:
    Try to start the computer in safe mode na dhcekc if the same problem occurs:
    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

    Method 2:
    Try to restore the computer in safe mode and check if it helps:
    http://support.Microsoft.com/kb/306084

    It will be useful.

  • can not turn on my Windows Defender, the next error message... "Windows Defender encountered an error: 0x800106ba"... I want to control programs Start up ii

    I want my system up and running quickly.

    I want my system up and running quickly.

    If you have the following AV, antivirus, programs installed, close your Windows Defender. Purpose of these AVs have their own advocates. 2 defenders on the same machine will create conflicts.
    Bottom line: it's ok. It's normal.
    List of AVs which will stop Windows Defender:

    Norton
    McAfee
    AVG
    Microsoft Security Essentials

    If you have none of the above, here's how you Windows Defender:
    Start button > in the search box, type Services > press the Enter key > scroll to find Windows Defender, click on it >...
    topic status , it must be said... Has begun
    under Startup Type, it must be said... Automatic
    If it does not say that, right click on Windows Defender > click Properties >
    in Startup Type, click on the pointer to the right and select automatic
    to the service status, click Start
    Click OK when finished.
    For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

Maybe you are looking for

  • Portege S100: SD led flashes but the SD card cannot be recognized

    I tried several SD cards (size & make) in a S100, while the device tandis que l' appareil clignote flashes light when I push the SD card, it does not appear as a disk. The format utility does not show an installed device, nor the password protection

  • Broadcast A100-912: where to find the biometric co processor driver?

    Today, I bought laptop Satellite A100-912.I have the problem with biometric co processor.Where I can found the driver for this device. Thank you.

  • Fax HP Officejet Pro 8600 more without a phone fixed?

    We just dropped our landline, and now I would like to know if I can still fax since my Officejet pro 8600 and all in one printer without a fixed line. You can send a fax from this machone using a wi - fi connection or somehow, connect it to a cell ph

  • Could not get a new workspace!

    After mass-wipe in January I asked on apexea , a new area of work twice and have always no response and no. workspace.Is it because I'm Russian or what?

  • Suppress the display of the user based tab

    I am putting together an application and I have three classes of users using Apex 4.2.0.00.27.(1) public - the user can access all public pages with no connection.(2) registered user - the user can watch reports.(3) Director - full access to the appl