Control several devices two PC GPIB

Similar Questions

• Recommend products OR for my application (controlling several instruments at the same time)

  I'm new to Labview, currently only using the trial version.      There is money in my budget to buy control software, but I need to qualify my needs.

  What I try to do is to control several pieces of equipment to test as a single system, which allows me to perform automated on conventional measures

  and digital two way radios.

  Here is a list of the material I want to control:

  First of all, my controller is a & Rohde Schwarz 3 PSL.   Fully GPIB active and ready.  It is the PC control software will reside on.

  Equipment:

  Spectrum analyser Rohde & Schwarz FSEA 30 with modulation analysis package digital option B7

  FSEA 30 second, same configuration

  R & S AMIQ4 I / modulation generator Q (files of the software residing on the PSL3)

  Generator of analog signals from R & S SMY 02

  Agilent E4431B analog-to-digital signal generator

  Agilent E4406A spectrum analyzer/digital radio test set

  E4418B Agilent RF wattmeter with sensor

  General Dynamics R2670B service monitor

  A typical application will be a test of classical radio on VHF or UHF analog channel.

  The idea is to enter pass and receive frequencies through Labview or any software is best suited for the job, as well as modulation parameters.

  and have the following things occur: assume usage of 150,000 MHz with a FM frequency modulated 1 kHz sounds modulated to the deviation of 2.5 KHz

  in total, with your 127,3 Hz subaudible to a gap of 300 Hz

  Test phase of receiver: send commands to control of instrument of Agilent E4431B signal generator.   Level set to-60 dBm.  Set to 150,000 MHz frequency.  Set

  Audio 1 to 1 KHz and audio tone 2 to 127,3 Hz at a level of 8 pecent of your 1.  SD total do not exceed 2.5 KHz.      Inject the test signal into port RX

  on the radio.

  The value R2670B SINAD function, related to the radio via the audio output port.

  Signal level to ramp down to the SINAD falls to 12 dB.

  Increase the level of the signal to the attenuation of 20dB.   Measure the audio distortion.

  Testing of transmitter: using the attenuators appropriate necessary on the analyzers of spectrum, and/or using a switched network of wiring.

  place radio to transmit using above specifications frequency and modulation.    Analyzers to receive on the frequency designated value

  and measure the transmitter specifications, including nonessential radiation measurement and harmonics.    Measure actual output power

  Via E4418B-power meter.

  I use two monitors to perform multiple tests in a same transmission. One is optimized for spectral purity tests while

  the other analysis of modulation characteristics.    Frequency, duration and RBW are defined according to the needs.

  When you test a digital radio, the signal chain is slightly different.  The AMIQ I / Q modulation generator s I / Q outputs are sent to the

  I / Q inputs on the Agilent generator, the power is on to accept external I / entered Q and the FSEA Spectrum Analyzer (an a)

  the) is passed to a preset that implements all relevant digital parameters so that it can be used to directly evaluate the digital transmissions.

  It is not a very developed in the planning system, but I do not know now whether Labview is everything I need or if I'll need to Teststand or another

  software packages.

  I'll probably want to ask for some advice on how to get this set up, eventually.

  LabVIEW is more than capable of this task. That's what it was designed to do. Use the help > find the instrument Drivers to find and install the drivers that you can use to control and read.

  TestStand generally requires the use of a programming language. It runs the tests that you write and provides functionality built for the production of record and report database then you would need to write these modules yourself with LabVIEW fair and some add on box to tools. For a single test configuration, it is perhaps an exaggeration, but it is interesting to watch as an addition.

• I have no sound. All the updates and driver controls show "device working properly.

  All the updates and driver controls show "device working properly. When the sound icon is clicked - I see the sliding green scale showing "audio output". I also see the green bar moving on 'Realtek HDMI output' and it is marked as default. Our sound stopped suddenly without reason is apparent. Any help is appreciated.

  When I go to check microphone/video on attached USB camera/mic - I see the two audio and video movement for this device. The computer makes the numbers / noise I just can't hear it.

  Realtek High definition driver is 6.0.1.5789.

  Change the sound Realtek HD audio no audio HDMI

• Can I use my software on several devices?

  Can I use my software on several devices?

  Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html

  -Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0

  -Windows or Mac has no importance... 2 on the same operating system or 1 on each

  -Two activations may NOT be used at the same time (noted in the link above of the license)

• Several devices on Stream 8 Bluetooth pairing

  Hello

  I just wanted to know if its possible to pair 2 or several devices such as the mouse Bluetooth and a Bluetooth keyboard on stream 8 and simultameously work on both?

  Kind regards

  Hrishikesh

  Hello

  Keyboard and mouse Bluetooth Bluetooth work wonder, at the same time.

  I have HP Bluetooth keyboard T800 paired with 8 HP flow, just got one case iBall mouse tried bluetooth pairing with 8 Stream and here we go!

  Keyboard and mouse are paired and works like charm.

  More importantly, I have my free to load usb microphone, USB key, etc..

  Almost want to mini computer, mouse and keyboard, extremely portable and easy to carry.

  Kind regards

  Hrishikesh.

• Factory recovery finished, now several devices in system without driver

  Hello! I have a desktop HP Pavilion p7 - 1236 s with Windows 7 Home Premium x 64. I got the factory settings last night using recovery discs HP bought for my specific model. I have not installed/uninstalled all programs, drivers, etc., and now, Device Manager lists several devices of system without a driver.  The list includes: 2nd generation Intel Core processor to DRAM Controller-0100; direct memory access controller; high precision event timer. Intel 6 series/C200 Series Chipset Family SMBus Controller - 1 22; 5 instances of resources of the mother; digital data processor; programmable interrupt controller; 2 instances of card system; and the system clock. Before you recover my system last night, I had uninstalled the Intel RST 11.0.0.1032 program version. I have a single 1 terabyte hard drive (no RAID) and use the computer for my home-based business, and I had read elsewhere that it is not necessary for such a situation. Following this recovery, I see that the pilot in the path: C:\SWSETUP\DRV\Storage\Intel\RST\11.0.0.1032; However, the program is not in the programs of the devices & or Device Manager. -What is originally is current driver problems? I'd be VERY happy any idea that you could provide. Thank you!

  pammywammyv

  You are the very welcome, Pam.

  I hope HP will do a great job, fixing the problem.

• Control Panel / devices and printers, click the printer, get an error message "impossible operation completed (error 0 x 00000005).» Access is denied?

  does anyone know why when I go into Control Panel / devices and printers, I click on the printer I want and you get an error message "impossible operation completed (error 0 x 00000005).» Access is denied? I can't change the owner, or delete or something. Help, please!

  So far, I found all these shapes to be completely useless and a waste of time. I found out how to fix this and it looks like that many people would have put me the answer out there because nobody else will or knows it.

  -Start

  -Explorer window

  -C:\windows\system32\spool\PRINTERS

  And

  -C:\windows\system32\spool\DRIVERS

  -Right click on a folder at a time and select Properties, then on the Security tab and add the user you want to grant access to print and check that the 'Total control' box is checked. If the user name is already there, check the box "total control".

  -Note: Never simply put the group "Everyone" it as it will cause problems if you use a vulnerability scanner.

  It was on a Windows 7 operating system.

  Who should do this; Well it worked for me at least.

  Thanks for nothing, Microsoft and all the people here! ***

• Are we able to purchase volume / multiple licenses for Adobe Acrobat Pro XI for several devices?

  Are we able to purchase volume / multiple licenses for Adobe Acrobat Pro XI for several devices?

  Hi communityn4038818,

  You will need to purchase licenses of Acrobat DC volume & then do volume license downgraded XI Acrobat by contacting the Adobe volume licensing team.

  This is only possible in i.e special case, you will need to purchase Acrobat DC volume licenses.

  Another option is to go for ETLA where you will be able to download the old version. I will recommend you contact Adobe Volume licensing team Business software licensing | Purchase Adobe programs for assistance on this issue.

  Kind regards
  Nicos

• Registration with several devices in hearing issue

  Hello-

  I'm working on Windows 10 on hearing, so I don't have the ability to record with several devices at the same time, given that I am limited to Windows provides the option of Ms. I know that I need to install a different driver while I have the ASIO option in the drop down hearing. What more reliable ASIO that I can install for free and do not give me a virus while I am able to record my external USB sometimes and the internal stereo mix of my computer?

  Thank you!
  

  The only way to achieve what you are asking is to find, download and install the free ASIO4All. http://www.asio4all.com

  However, if this will allow you to use the "internal stereo mix' of your computer I'm not sure.

• You can control several subforms (6) show/hide drop-down list

  Hi, I'm trying to get a drop-down menu to control the 6 options of subform

  List values

  1 = no value = 1

  2 = 1 value = 2

  3 = 2 = 3 value

  4 = 3 value = 4

  5 = 4 value = 5

  6 = 5 6 = value

  five forms

  codno1, codno2, codno3, codno4 (each a numeric / date)

  and codno5 (a notice of revision)

  I want javascript to the output/change of difficulty? event from the drop-down list

  something like that...

  but I'm not a programmer and not sure how to structure properly - any help/pointers please!

  I can get it to do the premiera with { }

  if (this.rawValue == '2')

  cod1date. Presence = 'visible '.

  }

  {

  if (this.rawValue =='3')

  cod1date. Presence = 'visible' & & cod2date = 'visible ';

  but when I try to control several subforms that it breaks...

  I thought that something like below makes sense...

  If this.rawValue is 6

  codno1. Presence & & codno2.presence & & cono3.presene & & codno4.presence & & codno5.presence = 'visible ';

  otherwise if

  this.rawValue == 5

  codno1. Presence & & codno2.presence & & cono3.presene & & codno4.presence & & 'visible' = & & condno5.presence = 'hidden ';

  otherwise if

  this.rawValue == 5

  codno1. Presence & & codno2.presence & & cono3.presene = 'visible' & & codno4.presence & & condno5.presence = 'hidden ';

  ElseIf... And so on...

  The syntax of your function that is not correct. You missed the quotation marks around the value of test and the break statements.

  var A = this.rawValue;

  Switch (A)
  {
  case "5":

  break;

  case "6":
  cod4date. Presence = "visible";

  break;

  case '4 ':
  cod3date. Presence = "visible";

  break;

  case '3 ':
  cod2date. Presence = "visible";

  break;

  case '2 ':
  cod1date. Presence = "visible";

  break;

  /*

  You can also have default parameters too:

  */

  by default:

  }

• I just installed Windows 7 on a part of the Dell Vostro 1500, l features notebook.__In control, I have two mistakes "Device Base system has not a driver" __There is no driver installed for the Base system device. _ No fixed

  I just installed Windows 7 on a Dell Vostro 1500 laptop.
  In the pane control, devices of l, I have two errors "device Base system has not a pilot.
  There is no driver installed for the Base system device. Not fixed
  Apply the solution to the complete driver problem
  Install a driver for this device does not work

  Troubleshooting gives me two messages:
  The first is: there is no driver installed for the Base system device.
  The device information
  Name: Base system device
  ID: PCI VEN_1180 & DEV_0592 & SUBSYS_02281028 & REV_12\4 & 1F967EE5 & 0 & 0BF0
  Error code: 28
  The second is: there is no driver installed for the Base system device.
  The device information
  Name: Base system device
  ID: PCI VEN_1180 & DEV_0843 & SUBSYS_02281028 & REV_12\4 & 1F967EE5 & 0 & 0AF0
  Error code: 28
  I cannot locate a driver through web search - how do I know what are the devices? and where can I find a driver?

  Try to update the drivers using Windows Update.  If this does not work, try the versions of Vista of Intel and Ricoh under Chipset drivers on the website of downloads & drivers for Vostro Notebook 1500 . Make a restore point first.

• iOS 10 questions implementation of several devices on Home App (HomeKit) for use with Hub of HUE.

  I can connect an iPhone but am unable to allow a guest or a second iPhone to the visionaries. Once I'm Setup on an iPhone, the second iPhone will not see the hub of HUE with their application to the home page. When I send an invitation for comments and they accept, they see my Home Setup, I created, but they get an error message saying ' accessories does not.

  I rest iphones and TINT Hub several times as well as home App and TINT settings. I'm still able to install one of the two iPhones at the start. The problem comes when you try to grant the second iPhone controls. I even tried to remove the TINT Apps to ensure that they do not interfere in some way. Both devices are able to use the application of COLOUR very well to control the lights, but we would like both the convience to control the lights of HUE with iPhone Control Center.

  Someone at - it stories of success with the connection of multiple devices using the Hub of HUE and Apple Home App for iOS 10 release?

  Both devices are iPhone 6 Plus running iOS 10. I have an iPad Pro available, but it is not setup for iOS 10 again or used for lighting control. The Hub of HUE is the latest model of square.

  Thank you!

  I have exactly the same problem.  My iPhone 6 s + works fine.  My children and wife iPads, iPods and phones running iOS10 are not.  They can see the app home screen and all the features of the installation.  But each device says "no response" and at the top of the page its says "no responding accessories".

  In addition, they can all use the app of Hue and set the lights very well.  However, not with Siri, but that's another question.  Once again my siri controls function very well.

  My guess is it's a bug.

• iTunes, update 12.4 and several devices...

  I use iTunes with two devices: on my iMac and iPad.

  In the past, I would spend between two devices opening iTunes while pressing control. I would choose for my videos and iTunes/iPod iTunes/iMac for my music and podcasts.

  However, after the recent update, I can synchronize with a single device. Is there a switch between iTunes on my two devices?

  Thanks for your help!

  Do you mean different libraries? You do this by using the option/ALT, not the control key.

• What is the right way to use variables controlled by the two buttons and programming?

  First of all, I apologize if this has been discussed before.  I know not how to phrase succinctly the application, so maybe I just missed the search terms.

  We have several pieces of the Labview software in the laboratory that automatically control things like the taps and heaters.  Sometimes we also manually control these same things.  I'm moving old NI PCI (and older versions of Labview) maps to a variable and based on compactRIO system shared network.  However, I'm still not on best practices to achieve.  I need to be able to have a script running at any time control panel so that I can access, for example, a valve controller (which is just a Boolean), and I need power open and close the valve by programming other scripts.  I need, of course, the control panel to track the State of the valve until it opens another script, the Panel indicates that it is open, and the next push on the control panel it will close.

  Historically, this has been processed using structures business to move from a "computer control" and "hands-on" with global variables that define the State of the valves.  Of course, this is not recommended.

  So far, I've played with the help of two variables, a status of valve and the other for the State of button.  The Panel configuration then loops, reads the status of the valve and puts the State of button if the State of the valve has changed.  I can do this with registers at offset or with the structures of the event, but anyway, it gets very crowded and seems inefficient.  Is there a good way to do this in Labview?  It seems this is a common problem, so I hope there is an easy and elegant solution that I've missed.

  Variable published use shared network.  Your scenario and your manual of the interface and change the variable and then shared your cRIO reads fair value and writes the appropriate values.

  Now for a cool part.  On your manual interface, right-click on your heart control that you want to use to control the shared variable and go to properties.  There should be a data binding tab in the Properties dialog box.  You can bind a control/indicator to a published network shared variable.  So this button will always be attributed to the current state.

  Your script should just read the shared variable before resuming to verify that it is in the correct state.

• Small size of device driver USB-GPIB for distro?

  Hi all.

  I had a search, and you can't find a similar question so I hope I'm not duplicating something...

  I created a little app to control an Agilen 53132 meter using the USB-GPIB device OR that I would like people to be able to use internally in my group. Driver I use has been downloaded from http://joule.ni.com/nidu/cds/view/p/id/2315/lang/en.

  I see that my app uses the following DLLs. However, I a) disseminate these and b) there must be some drivers below this level that will be required by a clean system.

  gpibconf. SLL, ni482.dll, nipal32.dll, nipalu.dll, nipalut.dll, nispylog.dll.

  Only problem I have is that it is almost 0.5 GB in size. I want my application to distro with a smaller subset so that the user can install just the driver concerned & dll etc I need for using the USB-GPIB device. Does anyone know if a driver more small value distro exist please?

  Thank you very much

  James

  There is no available smaller driver.