coprocessor device problem

Similar Questions

• Impossible to safely remove external USB HDD - ejection of mass storage device problem

  Hello

  I have a 250 toshiba external hard drive. "When I go safely remove device and click on stop, guests me that ' ejection of mass storage device problem and try later.

  Is there a reason for this? As I have heard it is dangerous to pull the cord without stopping it first.

  This happens usually when something is always access to the USB - HDD.
  Yes, it s dangerous to pull on the cable, because you can lose some data and the file system may be damaged. But if you have a situation where you need the drive to take with you and want to just get out the cable to the USB port there is a little trick to disconnect the security apparatus:

  Do right click on 'My Computer'-> click on Hardware-> click "devicemanager"-> go into "diskdrives"-> then you need to click on the drive that is your USB - HDD-> with the right button and then click on 'Properties'-> in the menu properties of this drive, you must go on "policies" and click on "optimize for quick removal"-> and then click OK and exit this menu and all-> perform a reboot-> closing information fact. :)

  After that, it s safe for remove you your drive even if it s not ejected. :)

  Welcome them

• Peripheral Audio USB-Mulit-channel has a driver problem and PnP device problem.

  I try to use the blue ice pre - amp for recording. Under channel-Mulit-USB Audio Device, device status, it displays "this device cannot start. (Code 10) "once I start the troubleshooting process it shows that even after reinstalling the driver it still does not work and that there is a problem with the device PnP I already tried to uninstall the driver and restart my laptop to let windows try again but nothing works.  Please help D:! Thank you all very much! :]
  -Kyle

  Hello

  1. is this problem limited with a specific USB device?

  2. it worked before?

  3. using this unit for the first time on this computer?

  4. the other USB devices work properly?

  Method 1: Run the troubleshooter and see if it helps.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues. You may need to update the chipset drivers and the USB controller

  Follow the given article below for more information.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  In addition, update the driver from the manufacturer's Web site and see if it helps.

  Method 3: Uninstall and reinstall the USB drivers and check if the problem persists

  1 disconnect all USB devices except the USB keyboard and mouse.

  2. click on start and type device manager in the start search box and press ENTER.
  3. Select the Device Manager and a pop-up window will Device Manager.
  4. click the + on controllers USB Bus to develop it.
  5. right click on all controllers USB and USB Root Hub that is listed, and select uninstall.
  6. restart the computer.
  7. plug in the appliance and check if it works.
   
   
   
   
  I hope this helps.

• External device problem - "YOU NEED of PERMISSION to PERFORM THIS ADMINISTRATIVE TASK" & after I click 'YES' it says "DESTINATION FOLDER ACCESS IS DENIED."

  Original title: external device problem

  Whenever I connect any external devices like pen drive & sdcard, I can't write anything in them, that they are not protected in writing! But I can copy things from them, but I can not cut & paste anything on their part in my system. I can only copy & paste. Whenever I try to write anything he says 'YOU NEED of PERMISSION to PERFORM THIS ADMINISTRATIVE TASK' & after I click 'YES' it says "DESTINATION FOLDER ACCESS IS DENIED." When I tried to format these devices, he says "YOU do not HAVE ENOUGH PERMISSION to PERFORM THIS OPERATION".

  Please help me!

  Sriram salvation,

  Have you tried the suggestions in the previous answer?

  I suggest you to disable the antivirus application and check the status of the issue. Refer to the following steps:

  a: you should see an icon for your Antivirus program in the taskbar notification area. It is usually at the bottom right of your desktop.

  b. click the third-party security software, you will see a pop up.

  (c) in this pop and select the option to disable, click on it.

  d. now third-party security software will be disabled.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Please let us know if you need assistance.

• Acer Aspire 4530 coprocessor driver problems

  Hello

  I have this Acer Aspire 4530 running Windows 7 (32 bit) opportunity and it didn't gave me no problems so far.  When I boot, everything loads and works very well, but I now get an error message for the coprocessor indicating:

  The drivers for this device are not installed. (Code 28) There is no driver selected for the item or a set of device information. To find a driver for this device, click Update driver.

  (Location: PCI bus 0, device 1, function 3)

  When I pick up my hard drive, and the www, it can't find the drivers.  I'm at a standstill.  My laptop still works and all the programs run very well, but if I'm supposed to have a driver installed for the coprocessor, so I want to install it.  Any help would be greatly appreciated.  Thank you

  You must install the chipset driver Nvidia from here: http://www.acer.co.uk/ac/en/GB/content/drivers

• Device problem: "Master UDS Bus of Kernal USB driver software Bus by TCP is not installed. Looking for driver fails.

  New install of Win 7.  Control Panel >... > devices and printers: problem with the computer. Convenience store ran with results: "pilot of Master NODES Bus of Kernal USB software Bus by TCP is not installed. Looking for driver fails.

  Note: the only known problem I have is that I can't print to a printer USB connected in local (HP 5280).  Curious, the printer PC utility I can print a test page.  Microsoft Office 2007 apps, not printing.

  I get the same error message.

  It seems to be related to my D - Link DIR-655 Router and software (offered through D-Link) called "SharePort," which allows the USB port at the back of the router to use for networking!

  I have 5 PCs on my home network and printer. With installed Shareport, I connected my printer to the router via the USB port. I don't have to have the computer on it, I used initially to install the printer.

  To access the printer on any PC, I just have the icon in my taskbar.

  The error message is displayed because, by default, SharePort is closed and it reads it as "not installed"!

  I used it with Vista and Windows 7 Ultimate x 32 and x 64 with no problems!

  Just as with the 'coprocessor' "impossible to install driver" error message, I uninstalled them in (several times) Device Manager and the error messages no longer appear!

  So, in my case, the messages themselves were the only mistake!

  FYO: Coprocessor refers to hardware devices such as fingerprint security to access your PC, instead of a password!

  I hope this has been helpful!

• Reboot and select good Boot Device problem - my PC does not start!

  Hi all

  Whenever I turn on my computer I get the message "Reboot and select proper boot device or Insert Boot Media in selected boot device and press a key.

  I checked the diagonistics material and these are the results:

  Test CPU-

  Hard drive: failure of the connection Test - Error Code: BIOHD1

  Memory - past

  I don't think that the issue is a faulty connection. My reason to believe so because I think that I had a virus on my computer (I was not able to confirm) I tried to delete the last time I was able to use the computer. Then I turned off the computer to restart, but unfortunately, that's when I got this error message.

  I had this problem once before (about 3 years ago) and I was not able to solve this problem, so I just stopped using the PC. Then one day my Dad turned on the computer (a few months later) and it worked all of a sudden.

  Anyone know what this problem is? How can I solve this problem?

  Any help is greatly appreciated! Thank you very much for your time and effort!

  Additional information:

  It was originally a windows 7 PC, but I have upgraded to windows 10, which is the current operating system.

  Product: HP p6620f

  I managed to start my PC again.

  I have unplugged all connections and left it that way for about 24 hours. Then I plugged everything back in and all of a sudden the PC worked again. I don't know if it will last, but right now it works.

  I'll write another post if something changes.

• Sam 1710: its device problem

  I hope someone can help me with a problem I have with the sound on my satellite 1710/windows ME nd I really don't know much about accesoriess!
  I've only had this machine for a few weeks (second hand) and the only sound I can get fromm, the machine is the starting beep, and I'm not 100% positive that it was never sound. Checking the audio option in the Panel shows actually no playback device in the preferred audio playback devices. I deleted the audio driver from the Device Manager and after a reboot has been installed a pilot audio crystal SoundFusion (TM) cs4281 wdm - but no luck with the sound, I'm afraid. I presume there must be asound card if generated startup notbook auto install the crystal software.

  Hello

  Yes there is a device available audio crystal and it is normally detected by ME like in your case!

  First of all, you must enter the BIOS with ESC after starting the laptop and load the default settings.

  Do you have the Toshiba Recovery CD when you bought the laptop second hand? If so you should grab the laptop and unless the audio device does not work after that, it might be a hardware failure!

  Bob

• USB Mass Storage Device problem

  I have the HP Pavilion Elite E9120f desktop computer. Whenever I start the computer, it shows that I have USB mass storage drives, G, H, I and J. However, there is no attached USB mass storage device. No one knows why this happens? I just usually click on the removal of the safety equipment and remove false devices. I get the message "this device can now be deleted without the computer problem. This machine runs Vista and has a 1 terabyte of hard drive. Thank you

  Bart, have you checked in 'My Computer' when this happens to see if the drives are there?  Almost looks like you have a virtual drive on your computer program.  Check also in start/startup to see if he is there that nothing listed that could cause this to happen.  Four readers Ghost is really strange.

• Satellite A210 - 1 4 - devices problem after upgrading to Windows 7

  I just installed Windows 7 on my Toshiba Satellite A210 - 1 4 and most of my hardware laptops works fine. However, there are 3 devices listed problem and I was wondering if you would be able to help me to identify them so that I can install the drivers.

  Base system device PCI VEN_1180 & DEV_0592 & SUBSYS_FF101179 & REV_12\4 & 1 to 5 DE67B & 0 & 33 A 4 that the drivers for this device are not installed.

  Base system device PCI VEN_1180 & DEV_0843 & SUBSYS_FF101179 & REV_12\4 & 1 to 5 DE67B & 0 & 32 A 4 that the drivers for this device are not installed.

  Not available ACPI\TOS1901\2 & DABA3FF & 1 that the drivers for this device are not installed.

  Thanks in advance!

  Check http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78

  If you still have any questions please let us know.

• Satellite A100 and USB audio device problem

  I bought "toneport ux2 line6" and it does not work with my computer laptop (dual core 1, 73GHz, 1 GB ram, Windows Vista).

  The problem is when I listen to music through this device, it looks I would look scratched CD, from time to time that there is a short interruption. The same thing happens when I'm with gearbox (software that allow you to play the electric guitar using audio device). I checked everything, including change Windows XP OS.

  I have the latest drivers for the port of your (compatible vista), I downloaded 3.5 mechanism, only toneport is connected to my computer, I have disabled all installations flashing in vista, power management is scheduled for high performance. I disable the sound card. I checked my cell phone with line6 monkey and it says everything is ok. I checked the audio device on my friend's Office, and it works well.

  I desperately need help.

  Hello Marcin

  In my opinion, you must be sure your laptop running fine and according to your assignment I do not here no problem.

  So in your case you have problem with some additional equipment or third party software. Am I wrong? If there is a problem I see no reason to seek the solution with Toshiba. You should contact the manufacturers of all the devices and software that you use. They should have enough experience with own products and they should offer good support in troubleshooting.

• 2000-219DX HP laptop: Ethernet controller, network controller + PCI device problems

  Hi ~!

  I got tired of finding solution to it, or let's say 3 problems in one.

  I reformat this laptop because of its slow and late development status.

  When I finished reformatting, it is the wifi button does not work and remained orange light, which means it's off.

  e I'v tried to plug it into the router via a cable (I forgot what it's called), then stil it doesn't work...

  I also checked Device Manager and found them with "!" exclamation.

  Problem controller Ethernet controller, PCI device and network.

  I found this will never work...

  Now, I did find the solution through the internet and found some but that did not work...

  I need help. !

  name of product: notebook PC HP 2000-219DX

  OS: windows 7 Home premium

  Hope you can help me... I really enjoyed that.

  -Marie

  Hello:

  These are the drivers that you need for these devices in the order you have them posted in the topic...

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp52421.exe

  This package contains the installation package driver for the controller LAN Realtek RTL8188CE wireless in the notebook models and operating systems.

  File name: sp52212.exe

  This package contains the driver that allows the Realtek card reader in laptop models running a supported operating system. The card reader allows users to read or write to removable storage cards supported, which are typically used in digital cameras, digital music players and cell phones.

  File name: sp52186.exe

• Audio device problem on Windows 8 64 Y510

  Hello dear readers. I have a lot of problems with my audio devices after the operating system upgrade to windows 8 on my lenovo y510. First of all default settings and drivers that I am working as any other failure, are evidence of each pair of speakers (this particular machine has 2 x 2 speakers and a subwoofer) as different devices on my audio settings. This of course means that I can only listen to one channel which is frankly frustrating...

  I tried to update the realtek drivers, and after restarting, I as a single device. With the help of those who suggested on lead lenovo horrible failure page, so I don't even bother. I think that this may be connected to the lack of software Dolby Home Theater, but all attempts to install it gave rise to a message "pceee is not installed.

  Did anyone of you had similar problems on this laptop in particular?

  TL; DR I would spend devices 5 speakers 3 in peripheral location 5 1 speakers

  TIL: I'm a fool.

  Well, turns out I found that my original drivers for Vista work like a charm.

• Virtual Excel file import NI Switch Executive device problem

  When I try to import OR switch Executive configuration to a file .xlxs error

  "An error occurred trying to read the file. Invalid device name «THIRD _PARTY_MATRIX» IVI "An error occurred while trying to access primary device _PARTY_MATRIX error THIRD: (Hex 0xBFFA4001) unknown status code.

  is displayed. I have no problem importing OR switch configuration Executive in .xml format! Can someone tell me why? Please, I beg you!

  I use a switch

  Executive 3.0

  Measurement and Automation Explorer worm 4.5.0f0

  LabVIEW 8.6.1

  Thank you very much

  Hi Mehran,

  Thanks for providing the attached files.  I have determined that the cause of the problem may be due to a setting of simulation of IVI.

  Currently, your IVI Driver Max sessions are configured so that simulate attribute is set to False.  This means that real hardware must be connected when opening a session IVI instrument.  If you do not have the hardware attached, then the call to initialize IVI fails (and potentially bad, depending on how the IVI specific driver manages an init call without hardware).

  Import the NI Switch Executive configuration in .xml format does not cause a problem because simulate is always set to true in the call to initialize of IVI.

  We will consider changing the import Excel in the future to also have always simulate the True value.  Time, you can a) check the hardware is connected when you import Excel, or b) set the value "Simulate with" Max to 'Specific Driver' applicable IVI pilot sessions.

  Example of setting "with"to simulate 'Specfic Driver' of MAX:

  

  Let me know if you have any other questions!

  Chad Erickson

  Switch Product Support Engineer

  NOR - USA

• Device problem

  Hello

  I have difficulties to find a MAX; the device is a multimeter of HP. I am connected via a GPIB/USB connection. Using the Agilent connection expert I can locate the device, there is no problem with the cable or the device itself.

  I recently uninstalled/reinstalled the software NOR, so it is possible that I forgot to download and install a necessary program. I installed Labview 8.5, as well as the full VISA and VISA DURATION. In Labview, when I click on refresh to get VISAS, no device not developed.

  The point about Agilent connection Agent had nothing to do with the instruments. I asked if you were using an Agilent GPIB controller.

  To activate the Tulip, open MAX and expand the software list in the left window. Select NI-VISA and in the right window, exapnd General settings on the Options of VISA tab to show passports. Check on the passport of NI-VISA for Tulip.

  There may be other necessary things if you are using an Agilent GPIB controller. Search the forum for the model number you use or do a search for Agilent GPIB.