Correct installation of the new hard drive for Windows 7

Similar Questions

• where are my drivers? new installation on the new hard drive

  I have a dimension e510, I put in a new hard drive. I got the windows xp disk, I added when I bought the computer. In general, the hard drive is partitioned or something with the operating system on the hard disk of windows xp.

  In any case after I installed widows xp, everything works except that I have the yellow question mark by 'other devices', I noticed that when I tried this computer with my main computer of the network. All of the devices under the heading other have no driver video Ethernet, PCi, for example - video works as I have a video card.

  So I tried to install the drivers and windows is unable to find them. I still have the installation disc into the computer. Being one of the drivers for the Ethernet - i cannot access the internet to get drivers. Help

  OK, I found the drivers on the dell site. I was able to install or update several drivers that I didn't need. the pilot opne I need comes in a cab file inpenuxp.cab.  Where do I put this? I've tried several things that work. When I low laoded the other driver of dell updtates, they all seemed different and they are all installed without problem

  Hello

  You will need to download "Intel PRO/100 VE Network Connection " of Dell on a USB key and install the driver for your Netbook have access to the internet.

  A CAB file is a ZIP , CAB file is just the Microsoft format for a compressed folder save bandwidth on their server they save as aCAB , you can open and then select all and extract here where the files need. For the most part, these files will file dell cascading, images and Html pages.

  Try to download the network card in your computer to get the correct driver installed for your problem.

  NASS - http://www.nasstec.co.uk

• Windows 7 installation on the new hard drive failure

  Install Windows 7 on a new hard drive. The new HDD is 750 GB Sata 3 GB 7 200 RPM.

  Windows 7 will not finish installing.

  Commissioning of repair using windows in the drive disk cannot complete until the end of Windows 7 install.

  I had installed Advanced. Creates a new 30 GB partition. Windows will create a 100 MB partition. I installed Windows 7 on the 30 GB partition. It will go the whole process until the completion step. It restarts, the blue screen appears. Where, it is said,

  (Attempt to Reset display driver and recover from Timeout failed.)

  If market, it will start to the top and do the samething.

  Before that my old hard drive went bad, I did a Windows 7 upgrade and updated all the drivers. Everything worked very well.

  Now, this is a full installation of Windows on the hard disk again.

  Here is the computer info I had saved.

  HP Pavilion a6250z PC
  -Genuine Windows Vista Home Premium (32 bit)
  -AMD Athlon (TM) 64 X 2 5600 + dual core - 2.8 GHz
  -3 GB DDR2 - 667 MHz dual channel SDRAM (2 x 1024, 2 x 512 MB)
  -512 MB NVIDIA GeForce 8500GT, DVI - I, TV, HDMI out
  -802.11 b/g USB Wireless LAN card & USB external modem
  -HDD 400 GB 7200 RPM SATA 3 Gb/s
  -LightScribe 16 X MAX drive DVD +/-R/RW SuperMulti
  -16 x Max DVD-ROM
  card reader memory 15 - in-1, 1394, 3 USB, audio
  -Tuner TV ATSC-NTSC with PVR, FM tuner, remote control
  -7.1 audio channels w/front audio ports integrated

  What I am doing wrong?

  Thank you for helping me

  I solved my problem.

  I replaced the NVIDIA card and did a fresh install and everything works fine.

  Just a ton of updates and it will be like new.

• What to do next after the installation of the new hard drive.

  I just finished installing a new hard drive in my HP Pavilion dv4-2049us laptop computer Windows 7. What should I do to get the operational computer then?

  for example I have to re - install Windows 7 from the disc? Or, do I have to use a disc of "Boot"?  BTW, what is a boot disk?

  Hello

  Please try this: in the first screen, select internal CD/DVD and press F10 to save the configuration. You will need to switch it to HARD disk after loading the operating system on your machine.

  Kind regards.

• Can't activate Windows 7 (OEM Version) after the installation on the new HARD drive

  Hello, recently my HARD drive crashed and I replace it with a new one, but after I reinstalled my window 7 (OEM Version), I can get it activated. The error code is 0xC004C017, I tried to activate using different methods, but the options given to me is only 1) buy a new product key online 2) try a different product key for activation of Contact 3) Microsoft to help solve this problem. There are no other options available to me as the activation of the phone.

  Please tell us how can I activate my Windows 7 on my new HARD drive.

  Thank you

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• Add the new hard drive for HP 700-147C

  I bought a new desktop model 700-147, AMD APU A10-6700, 1 TB didk lecteurC.  I have a 1 TB drive that I rescued a HP Pavilion death I want to install in the new computer.  I can't find instructions for this operation.  What cables do I need?  Where can I get the proper cables?  Where do I Pug in?

  JDBrwn, welcome to the forum.

  Here's a guide to help you install the hard drive.  You can buy the cables at any store that sells computer supplies; Best Buy, etc.

  Please click on "BRAVO", if I helped you and click on "Accept as Solution" If your problem is resolved.

• Quality/compatibility of the new hard drive for my laptop

  I have a toshiba satellite A105-S2194. I went online to get a replacement from the hard drive. The guy who I spoke to suggested that I get the data of 1 TB 2.5 5400 RPM. I asked if this was no exaggeration for my computer and if she would work with her. He assured me he would. I have windows 7 to load on this subject. My question is. It is true that he did and work in my laptop? It is with Fed - ex delivery and need to know whether to install or send back

  The SATA standard is so clearly defined that virtually any disk 2.5 "will work on a laptop. High speed drives (7200 RPM +) could draw in theory more current that might have been specified, even if the newer readers are more effective. With regard to the compatibility of the BIOS limitation of size should not enter up to 2 TB

  Even if the laptop is quite old it supports disks more large, Toshiba lists only readers that they mounted but Crucial list upgrades up to 1 TB.

• Satellite Pro L650: Windows could not complete the installation on the new HARD drive

  At the present time, I have a 500 GB HARD drive installed. As soon as I got it, I did a recovery on 3 DVD media.

  I just tried to replace the HARD drive with a 1 to one. All copied OK and after dvd 3 that I was told to release the dvd. I did this and the computer turns off. I turned it on and it started to (don't remember the exact words used) set the drivers.

  However I have now received the message that "Windows cannot complete installation" and telling me to reinstall. I did it, but after the steps above have repeated the same message appears.

  Pls help.

  I don't see why my computer should be limited to a 500 GB HARD drive.

  Thank you

  Hello

  The computer is NOT limited to 500 GB HARD drive
  You can use more big 500 GB hard drives. You have confirmed that the laptop supports 1 TB HARD drive and the system recognizes the 1 TB HARD drive.

  The problem could be the use of the recovery diskette. Why?
  Because the recovery disk creates the same partitions that were available on the 500 GB HARD drive. This could create problems of system due to the large size of HARD drive.

  Solutions?
  Well, I think that you could install the system by using the clean installation of Microsoft Windows disk.
  Missing other drivers or tools can be downloaded from Toshiba page.

• Windows XP operating system installation on the new hard drive

  My hard drive crashed on my Dimension 3000 desktop computer and I am trying to replace. I managed to install Windows XP Pro and all the drivers. My problem is that Windows application authentication code, when I enter what is on the side of the tower that sometimes invalid. It's prompting me to buy another license.

  Any ideas?

  bdives

  
  

• Incompatible with the controller hard drive for Windows 10 update

  After 4 TEC, I was able to update Windows 10.  Now the report of compatibility for my computer says that my hard disk controller is not compatible with Windows 10.  I have Windows 7 and its been running pretty well with some minor problems.  When I go to search for drivers or windows updates, it seems to continue indefinitely and do nothing.  Not sure if that has anything to do with the controller, but I thought I would include this information.

  The latest technology suggested that I go to my local IT guy... funny, considering it's my computer at home.  What are my options?  Or someone has an idea how I could get the controller fixed my own?  Or should I consider 10 Windows a lost cause and wait until I get a new computer?  Thank you!

  Hello!  Thanks for the reply.  I've updated driver for the controller, and the next day was 10 Windows in my Windows Update.  I opened it to the top, and it worked!   Now have 10 Windows happily running on my computer.  Thanks for the information!

• Restoration of the external hard drive for Windows 7 System Image

  I created a System Image on my external hard drive. Now when I choose ' select another backup to restore files of "the hard drive is not detected. Even after you reconnect the hard drive and click Refresh it is still not detected.  Help!

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• No Internet after the new hard drive and Windows 7 Clean reinstall

  I have a Dell Studio XPS 9100 I bought in 2011.

  The Seagate Barracuda SATA 1 TB hard drive died, and I replaced it with a Seagate Barracuda 2 TB drive. The re - install Windows 7 went ok, but I couldn't connect to the net.

  A ran the device driver and got errors on the network card and the RAID.

  I went on the site of Dell for the 9100 and installed the drivers for the adapter and the RAID.

  No luck. I always get the error "no card" as well as the error 'no cable not connected.

  I read a lot of posts about this problem and am stuck.

  Someone has an idea how I can fix this once and for all and go on the internet?

  I advise to patch Windows 7 with the WSUS Offline Update:

  http://dellwindowsreinstallationguide.com/WSUS-offline-update/

  Dell System Software:

  http://ftp.Dell.com/FOLDER88677M/8/Dell_System-Software_A03_R282538.exe

  Intel Chipset Device Software:

  https://downloadcenter.intel.com/download/20775/Intel-Chipset-Device-Software-INF-Update-Utility-

  NEC USB 3.0 host driver:

  http://downloads.Dell.com/comm/R266197.exe

  Card reader:

  http://downloads.Dell.com/Input/R266195.exe

  Intel Matrix Storage Manager:

  http://downloads.Dell.com/SATA/Intel_Matrix-Storage-Manager_A01_R230056.exe

  Realtek NIC:

  http://downloads.Dell.com/Network/R266204.exe

  Atheros Wireless Card:

  http://downloads.Dell.com/FOLDER02988710M/1/Network_Driver_9T8XY_WN32_10.0.0.309_A03.exe

  Note make sure that all the drivers for Dell extract and install and extract not only. If they extract only you will need to manually launch the setup.exe in the extracted folder.

• How to install the new hard drive and windows key?

  Hello

  I have a aspire v5-121-c72g32nkk.
  I have just updated to Windows 10, don't panic, but I want to upgrade my HD drive to a SSD drive.

  You can find the steps to do this?
  Windows was preinstalled, how I reinstall on another drive?
  I have no serial key or whatever it is.
  I'm a bit lost, you have an idea?

  Best,

  There are several ways to do this, anyone have product keys, since

  If you want to do a clean install:

  Windows 7-8 - 8.1 keys are embeeded on your BIOS

  Windows 10 use a generic key during the upgrade, so just skip the steps questions about a product key and the first time you connect on the web, it will authenticate to.

  You must decide:

  (1) do a clean install of your operating system to factory

  (2) make a disk - image of the system image and reload

  (3) to do a clean install of windows 10

  option 2 is the fastest at the end, as you create a copy of your HARD drive and reload it to your PC.

  you need a bootable windows 10 (USB or DVD) media and little space on external HARD drive.

• I get a recurring answer ' * stop: 0x0000007B (0xF7BFE524, Ox0000034, Ox00000000, 0x00000000) "after the installation of the new hard drive into the computer laptop viao.

  Tried to boot from a hard disk with a blue error screen. Replace the SATA drive with 500 GB drive. Then drive formatted and installed Windows XP Pro and McAfee 2011 office. Same error!

  Hello

  I suggest you to visit these links and check if it helps:

  http://support.Microsoft.com/kb/324103

  http://support.Microsoft.com/KB/314082

  It will be useful.

• need to change my old hard drive and install vista, a new moved it to the new hard drive

  change from my old hard drive with a new one.  Vista installs in the new hard drive

  How to clean install Vista:

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner