counter exit signs
I am currently using 6259 PCI which has 2 outputs of meter. Are there signs of counter that I can add to get a 5-8 additional counter output? All those I see on the Web site of NOR and Measurement Computing have two outputs maximum.
I like the idea of a low cost with meters USB device. If you have the chance to remember to fill a Product Suggestion to help us prioritize, maybe it's something that we could look at if demand is high enough.
In the meantime, you can watch in 9174 chassis that just came out 2 days ago. It uses the same chip of STC - 3 as our X-series machines, so there 4 counters available on the chassis backplane. To access outside you will need to use a digital module as the 9401.
The 9174 connects to your computer via USB and is programmed with DAQmx (support added in version 9.0.2).
Best regards
John
Tags: NI Hardware
Similar Questions
-
using the extract of "on mouse click" in cs5 gives the following code as an example of code for something that can happen when you click on
trace ("mouse clicked");
The notes say that this adds 'mouse clicked' for the exit sign
all previewing the file in flash by clicking on the object mode append this line for the exit sign every time.
But while previewing in other modes such as html, is notWhat exactly is the exit sign
It stores data that can later be called or if it has no use?
The trace command and the exit sign are two of your best friends when it comes to testing and troubleshooting of the code in a file.
You can use the trace command to do things like knowing that some values are at some stage of processing or when something fails to deal with as long as you expect. For example, if you configure a button to work with a function but the button doesn't seem to work, you could put a trace of this function to see if the button is actually the start of the function. If you see that it is, you can then change the trace to check whether a value that could inhibit the work function is what it should be or not.
The output panel is where the trace command offers to back up the information you want. It does not store all that you can use in your design and only comes into play when you run a file outside of the Flash software.
-
I'm counting iterations above and below 0 Volt applied (VAPP). It is used as a Subvi inside a For loop. One of them (the positive, I think) seems to work, the reset to zero for each series. The other seems to add to the previous one, every moment of execution.
For example, 6 intervals below and above zero returns 6 and 6 round, 6 and 12 the second time. I know this is a hack, but I didn't know how to do better.
Maybe try something like that. Reset if [i] = 0, for example.
-
Foliobuilder exit sign 22. impossible to install
After you download the version of Panel foliobuilder 22 and open, when I try to action, the installer, I get a message saying that the installer is defect and cannot be opened...
I try at least 10 times, with Firefox and safari...
I use OS x 10.8 & design SC.5... EN
Thanks for the help.
See http://helpx.adobe.com/x-productkb/global/error-signed-distributor-mac-os.html for steps to solve the problem.
Neil
-
I followed the instructions to add the output to bridge to CC Module but it did not work and now the bridge will not open at all. Any ideas?
The article was: Install Adobe Output Module
I have confirmed all the steps but at the end - nothing, nada, zip, zilch!
Thanks in advance,
Joanne
I had this same problem. I'm on a Mac. Make sure that the Bridge and Photoshop are not executed, so make sure that you copy the files to the system library and not your user library. After I did the pop up came up to the top and everything was good.
-
My Panel of Adobe Bridge output is empty - suggestions?
Please follow the described here for instructions http://helpx.adobe.com/bridge/kb/troubleshoot-errors-freezes-bridge-windows.html
1 reset preferences, reset the default workspace, and purge the cache.
And see if there is progress.
-
How do I get the total time elapsed displayed on the stage?
Hello
I have a program that will count every second past with a key press to the other, in the exit sign that I get all the time what past (per second), but here the total number displayed in a text box on the stage at the end. This will be the total time between supports.
Thanks for your help, it is very much appreciated as a newcomer in Actionscript.
Also, I use video clips of Doug Winnie to help me so if you know a particular episode that will cover then please let me know.
Mick
use a variable to store this value and increment when appropriate.
-
Inbox displays incorrect account
I use hotmail. my Inbox and junk mail folders show a number of unread mails, but there is no no read. Outlook (hotmail) shows no box of unread receipt or unwanted counties when signed to Outlook. Apple devices, iPad, iPhone, iMac, and Mac book pro all show a count of Inbox read and junk, when there is none. WHY? When Apple becomes bindles of and how do I get this problem? (It is not a problem of Microsoft).
This is probably just a bug, then try to restart the iPad or mail by signing in and out. Also, you should definitely update your iPad.
-
Problem with Web Builder and MySQL connection
Hello
I created a web service VI (see picture attached) to connect my Web Builder application with a MySQL database. The problem is that I get nothing on my exit signs during the call to the web service VI.
Some tests I've done:
(1) this web service VI works perfectly (I mean indicators 'value', 'status' and 'data_hora' give the desired result) when the VI run directly through LabVIEW. MySQL connection and my VI are OK...
(2) I know my web service VI was successfully built and deployed because the indicators give me some value if I sign something for them other than my SQL output
(for example: if I put a string constant "Hello" on indicator "valor" I get "Hello" when calling the web service VI)
I suppose that the database connectivity kit is not supported when a VI is integrated with a web service VI. In my case, kit screws are inside the subVIs 'start', 'exec 2d' and 'stop' showed in the picture as an attachment.
Any idea?
Thank you
Marcelo
I'm using LabVIEW 2001 Wesley, but I solved my problem.
It was just a MySQL data source problem: I just had to add my info DB through C:\Windows\SysWOW64\odbcad32.exe.
Thank you
Marcelo
-
How can I test to see if another application is running?
I manage systems remotely via start PC Anywhere Some VI automatically load, but because of a loop tightened with the VI I am unable to get support for PC Anywhere. I would like to put something in the VI seeking to check if PC anywhere works and if it is to end the loop of VI. Any ideas?
To determine if a program is already running try to use the TaskList command line program (assuming you are using Windows)
Execute a call to exec the system with being "tasklist" command line it will return the list of all applications running from the Standard exit sign. You can use this program to give also access to remote computers, but I have never tried.
Fund the available switches go to start > run, then type "cmd" hit enter in the command window type "Tasklist /?" this should show you how to use it to see what applications are running on a remote computer. I hope this helps.
-
In recent days, I noticed that my Photosmart C4680 is blower bike itself on and off. Anyone else have this same problem?
Does anyone know why its doing? Y at - it a solution?
Just do the repair. It was a bad capacitor on the logic board (TEAPO brand). There's that one to replace on this printer and it will probably look like curved on top (which indicates which are blown). It is 330uF 6.3V, but I got in a little bigger (16V, whatever they had in 330uF) and it works perfectly now. It's an easy fix, if you aren't afraid of soldering a component. It will cost about 60 c with a value of components. (and a kit of solder so you do not have a)
Open the scanner cover and the door of replacement ink. Reach behind the control panel and gently push a clip for the exit sign. He will reveal a hidden torx screw. There are four total screws to remove the top, and you can use a torx bit, or if no practice, the right to an allen key size.
Once you get the top up the rest of the printer, you must pull carefully on some connectors that attach to the logical map of its orbits. Some are simply Ribbon connectors and some wire connectors. Set the top aside.
Identify the bad capacitor on the Board by checking the upper surface. It is a green, a thin color that says TEAPO on it and if it is indeed the defective component it must feel to be curved on top.
Remove all the other connectors on the Board and unscrew 3 torx screws to remove the Board of Directors of the printer.
To unsolder the bad capacitor, it can be easier at first it break so you can extract each lead with pliers, one at a time when the application of heat on the side welding.
Respect the polarity, the negative side (identified by the sign on the new capacitor less) on the shady side to the Board of Directors.
Solder the new capacitor, clip wide leads, any excess back together. Your ' e did! Good luck!
-
Error trying to read the voltage/current off the coast of Keithly 24xx. Help!
Hi all
I am trying to program (keithley 24xx) power to set and an output voltage for a certain period of time. I wrote cela all on labview and it works very well. I then added the ability to read and display the voltage output and current on my exit sign. ATER, I did, after the end of the time, run time, I'd get a beep and this error:
Keithley 24XX.lvlib:Error Query.vi
Reports of the instrument:
803, 'not allowed with OUTPUT.
0, "no error".------------------------------------
«"" "String of full appeal:»»"»
Keithley 24XX.lvlib:Error Query.vi
. VI 24XX.lvlib:Read (Multiple Points) Keithley
. VI 24XX.lvlib:Read (Single Point) Keithley
Basic_Operation.VI-------------------------------------
My guess is that the output turns off while reading is still ongoing, creating this error. I tried to find a way to fix this problem without success. Any ideas? I have attached a screencap of programming
Thank you!
You are the ' turn off before that can't read. When the time is true, the output is cut. Why do you even exit to activate it inside the loop? Make the first function outside the loop so that it is called after the loop stops.
-
Hi OPA Experts,
We use the OPA 10.4.4. We have created about 25 excel files containing different conditions, with one or 2 each result (especially flag field "Y" or "n" out). It is that need a flag output, send us a request to OPA containing particular xml, for example excel file 1 and get the corresponding indicator of output in excel file 1. If we need all exit signs (all 25 exit excel), then send us several xml to OPA affecting performance.
Is it possible to combine all 25 excel files in 1 excel (to create a separate for each type of flag sheet) and invoke 1 single query XML?.
Moses,
OPA supports cell merging in Excel, then you can at least simplify the Excel sheet by merging cells of columns where the values are the same (columns of 1st, 2nd, 3rd and 5th). Who will save the one who maintains the Excel sheet a lot of extra typing
-
Impossible to move anything...
I am SUPER frustrated. I can not move suddenly anything in first time for everything. I can make new files, bins, etc. But cannot move anything on my scenario, or in my project folder. Help, please! I need to get some work done!
Mac: 10.11.4
I have a work around. It has something to do with the use of multiple monitors, or exit signs, or who knows what. The solution I found was to use only a different workspace. Window > workspace > choose someone from the list. Then go back to yours. Problem solved (with the exception of Adobe don't play not well with my computer).
-
Don't highlight invalid markup
Hello
It's my first time using Dreamweaver and I always wanted to use with photoshop. Anyway, I bought the full package of applications and I'm already having problems. I'm pretty decent with my knowledge of the Information technology, so usually I'm able to find what I'm looking for using the software. Well, I have worked on a website in Expression Web for a few weeks now and it wasn't so bad because I tend to type the code and fix everything in the code, rather than in design mode. The site that I built is intended to be a document of a single page, so I opened the main HTML file in Dreamweaver to see what I could do amazing things now, because Expression Web has greatly depreciated. which is probably why Microsoft is to let users get for free. One of the things more IMPORTANT I need of web design software is the ability to see where I mess up I go along.and to get suggestions from the software. I am, in fact, passed through workstations and it seems that Dreamweaver has this built-in feature. I followed the instructions of the discussion board posts and learned that you have to go to the 'VIEW' tab, then scroll down to 'OPTIONS of DISPLAY of CODE', then select 'set HIGHLIGHT the CODE INVALID. The problem is that this feature is grayed out so I can't select it. I have no idea why and I REALLY need this feature to work for me. I voluntarily left an invalid attribute just to see if I can get this working in service and other lines of code that I need to fix as well. I rarely post on the forums of discussion like this, however, I'm completely stuck. Can someone help me please? Here is a screenshot of the option is grayed out. Am I missing something? Again, I use the absolute latest version of Dreamweaver [from 08/11/2015], because it has been downloaded through Adobe Creative cloud even not 3 hours ago. Thank you in advance.
I suspect that option was left by mistake in the menu. He worked in older versions of Dreamweaver, but Dreamweaver CC 2015 now uses the code Linting: helps Dreamweaver | Lint code.
In your screenshot, there is a red icon in the status bar at the bottom right of the screen. The fact that it is red indicates the linter found coding errors. Click the icon to open the exit sign, which will tell you what are the mistakes and the line, on which they can be found.
Maybe you are looking for
-
How to put my MacBook to sleep
I've recently upgraded to a new MacBook, a MacBook Air and have noticed that he's not going to sleep by pressing the power button. Why has this changed? and is there a way to change this? I know that closing the lid and to choose the apple logo and t
-
Apple has cache and cookies? If so, how can I delete?
Products Apple have cache and cookies? If so, how can I delete?
-
Satellite Pro L300 - problem for Installation of Windows XP SP2
I bought a Toshiba Satellite Pro L300-164 without BONES. When I tired to a software install Windows XP Professional genuine, it gives a message "Setup did not find units of hard disk installed in your computer". Repeated trial gives the same message.
-
Como reiniciar impresion trabajos administrator
Trato print documents are only tells me that no you can print because no is pueden ver las propiedades del servidor. El servicio local impresion trabajos Administrator without be esta ejecutando, reiniciar el o el equipo administrator. No to como to
-
Tried to install Diablo III. Could not. Said (Vista) Operating System to SP2. Check out my features and went to the microsoft Download Center and download the sp2. Click on it to install it... half completed and stopped. Said "installation failed." T