CP2025: physically cleaning CP2025 ink roll

Ink red stripes sometimes my copies.  Not the cartridge as I changed it out.  The control panel cleaning cartridge does not.   Notice that the horizontal roll back printer has accumulated red ink on it.   Can I clean this roller with rubbing alcohol?  If not alcohol, how can I clean the roller?

I would not recommend using any cleaning solution or chemical of any kind on a transfer roller. Also, while cleaning the roller with a dry cloth, you can deform the surface and your impressions will not clear and sharp, be extremely careful with this component.

If you want to test to see if the secondary transfer roller is actually put toner on the paper, just some white sheets of printing paper and see if the toner is on the back of their. It is normal that the transfer rollers get toner on them over time.

It is the steamroller you're talking about?

You can get the show together above for about US $30. try searching with the manufacturer HP RM1-4838-000. It is likely that the magenta cartridge that you in place had something dirty the cleaning squeegee, causing toner continually put on the transfer belt resulting in this magenta toner get on your secondary transfer roller, as well as other locations inside the printer. I had to disassemble these printers before and remove the transfer belt to get the printer toner spills, so they could reprint cleanly.

Tags: HP Printers

Similar Questions

  • How to clean the ink cartridge? Print printer printing

    How to clean and align the printer

    Hello

    What is the brand and model of your printer?

    There is no universal method in Windows to change ink or toner cartridges because the procedure varies by printer. To know what cartridges to use and how to change them, see the documentation that came with the printer.

    Refer to How can I check my ink or toner levels?

    It will be useful.

  • Black ink cartridge will not print

    Putting in a new black ink cartridge the printer says it's there and full of new ink but when printing it don't use it. It happened the last time that I put in the black cartridge and I managed to do it finally work but don't remember what I did. Why is this happening?

    With printing black ink is not like that, there are only a few things you can try, and it looks like you did most of them. If the steps described in the following paper the link did not help, then you might make a physical print head cleaning. Bob_Headrick gave the steps to do this in the post below. If none of this does not work, you can either replace the printhead by contacting the support of HP, or you will need to replace the printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

    HP Technical Support call case form:
    http://goo.GL/w7Hgh

    Troubleshooting print quality problems:
    http://goo.GL/FHypA

    Physical cleaning print head:
    http://goo.GL/DfroJ

  • Toner roller

    The 9green of roller toner) is covered with toner.

     

    Is there a "safe way" to clean the roller?

     

    Thank you

    oldtrout - arsaidh-Brack
    GUM BI LEAT SI\TH
    Today is perhaps the happiest day of your life and
    succeeding every day be even better.
    May I always be the kind of person
    My dog thinks I'm

    Hi oldtrout,.

    I understand that the green ink roll is covered with ink.

    I'll be happy to help you.

    Touch the drum on the toner will ruin the toner.

    You can run a cleaning of the printer, but looks like the toner need to be replaced.

    What printer do you have?

    How can I find my model number or product number?

    Thanks for posting on the HP Forums.
    Have a wonderful day!

  • ink message

    "The C4750 seems to print normally, but has a message:" "clean printer ink blots."

    He wants the attention to something, but I can't find the procedure in the manual.

    Hello

    The ink is contained in the print head, and it's good that he does not flee physically. My suggestion is to use this print head empty and see if you get the similar message in the next replacement of printhead.

    If so, the problem is expected to be at the printer and you can call the HP support to see what they can do.

    Thank you

  • LaserJet 1020: Re-install the roller in LaserJet 1020

    The paper was not trained on my 1020 LaserHet.   I used the instructions in this video - https://www.youtube.com/watch?v=TvPZySVX8Zc - to remove and clean the drive roller.

    I removed the roller and cleaned.  I can't re - install the drive roll.  I made an attempt to re - install the roll, put back ink cartridge and print a sample page.  The printer makes a mechanical sound hard, so I stoppped printing.

    I'm trying to identify the problem.  I noticed that before I removed the roller, the small tabs of white on each side of the roll are found above the rotating metal bar that holds the roller.

    Now, the tabs are lower.

    I can't put the circular and rectangular holes on the roll in place to install correctly.  (I guess I don't align properly when I tried first to re - install them.)

    Any ideas on what I can do to fix this and re-stable roll?

    Thank you

    Barbara

    cycle power on the printer once and I hope that the pick up Assembly turn the roller in the right position.

    TO replace the turn off the printer and unplug unit, then remove the toner cartridge, you can manually rotate the roll holder around the right position.

    try turning off the printer one some time first of all, it should get back in the right position

  • Photosmart A716 Photo Printer INK BLURRED, JUST BLOB WET INK ON PICTURES

    We used this printer for about a year without this problem, all of a sudden, the photos are versions of just blurry blob of the actual photo. It is possible to do in the photo, but the ink is super humid and fuzzy with a halo in overall effect. they are horrible and useless. We have realigned, clean the ink cartridge, print several different photo even sessions on different cameras and it's the same thing. The problem certainly lies in the printer. It is more under warranty and they help me without charge. Any ideas?

    Sounds like a build up of residue of ink and paper on the rolls.

  • HP officejet 6500 not print black ink

    Have already used twice tools to check/fix printhead etc. and check all colors except black.  Of course now the colors are low because of controls but Black Watch 2/3 full.  Suffered the underside of the black print cartridge and has still not printing.

    There may be something clogging the printhead.  Do mechanical print head cleaning and check the ventilation on the cartridges, as indicated in this document.  If the wind seems correct, and cleaning do not receive black printing as it should, then you have to move to make a physical cleaning of the print head.  Bob_Headrick was kind enough to show the steps of this message.  After the physical cleaning you wish to still not able to get a black printing, then you will either need to buy a new printhead, or buy a new printer.  This printer print head is not all that expensive compared to the other models, but you can only buy it directly from HP.  I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

    HP Technical Support call case form

  • HP Deskjet D1470not impression after cleaning of the cartridges

    Why after I've cleaned my ink cartridges are my documents not print correctly? HP Deskjet D1470

    Here is a link to a document that could help you.

    Let me know if it helps.

  • printer does not print black not ink and paper gets stuck

    Hello

    My printer won't print anything in black ink from last night. It prints color very well and my black ink level is good.

    In addition, it starts to get a lot of paper jams. I use regular copy paper.

    Ive tried the printer alignment and cleaning the ink smears, but that does not work because as I said the paper gets stuck.

    My printer is hp officejet all-in one printer-4630.

    Help, please! I really need to print something tonight!

    In the paper here troubleshooting steps can help solve the black print is not in your Officejet printer 4630.

    In a pinch, you can go to the configuration of the driver and select the type of paper Photo paper.  This will use the color cartridge to print in black.

    Problems here, the document includes information to treat the paper jam .

  • Use of starter ink

    When my 8500 HP officejet A909a printer is turned on, he spends a lot of time blowing away until it's ready to use. Meanwhile, she pointed out to clean the ink heads.

    How much ink does use its cleaning ink heads?

    Is it better to leave the machine running to minimize this cleaning process?

    Thank you

    Hello Simplefella,

    Yes, you must leave the device, because it would prevent you from cleaning so. If you turn that it completely off the unit will clean his inktheads as a precoution. Because this unit is equipped with a fax, it is intended to be marketed in all the time. To avoid a greater use of power it is a standby mode built into the printer.

    Only small amount of ink are used for cleaning, but if you stop all the time a lot more cleaning will then be necessary.

  • ink cartridge problem

    Why, when I replaced a cartridge with a new cartridge, ink level still shows low.

    I do not use Windows8. I tried to clean the ink inside the printer, this is why a picture is not going to be useful. The ink was under the printer, too. I am able to print in black at the moment, and that's what I need at the present time, as the printer is probably 10 years, pay for repairs would not be cost-effective. Thanks for your help anyway.

  • Inkjet 1510: draws jet of ink 1510 all of a sudden half or faded to lines

    Hey all. Ive had this printer HP inkjet 1510 for about 4 months now. It printed fine at first but all of a sudden it started printing lines half or semi fainted faded lines. It can print on 3 or 4 lines Okay then half superior of a line is not there.

    I tried re-Kaleidoscope heads with receive computer software as well as a cleaning (also from the software) but its no different. Don't unerstand curious as whats it print very well in the beginning. I am seeking employment at the moment so it's a huge pain when I try and print my CV as it looks so professional. No idea what it could be or how I could solve this problem please? Thank you.

    Hi Vesuvius79,

    Please try to clean the ink cartridges.  Here is a video on how to do this

    https://www.YouTube.com/watch?v=1ggaTZWNcwM

    Let me know if this worked for you.

    Thank you!

  • Reference Dell v515w printer acts like it is printing, but there is no ink on the page

    I have a Dell Inspiron 5000 series and the v515w printer. I went to Windows 10 and if she is working for a short period until he acted like it was printing but no ink on the page. I switched to Windows 7 Professional and it still does the same thing. I uninstalled the printer and reinstall twice and still can't make it work...

    Hello Charlene,

    Thanks for posting your query on the Microsoft Community.

    According to the description of the problem your printer does not print text on paper as there is no ink. The question might be if there is no ink in the cartridges. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

    I suggest to check first the ink in the cartridges, and if possible, try to change with a new and see if it makes a difference. You can also try to clean the ink cartridge nozzles.

    If the problem persists, you can try the steps outlined in the methods mentioned below and see if it helps you to solve the problem.

    Method 1
    Try the printer troubleshooter, which will attempt to diagnose and solve your problem automatically.

    http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

    Method 2
    Clear printer spooler files and select the spooler service.

    Step 1
    a. Click Start, type "Services.msc" (without the quotation marks) in the Open box and click OK.
    b. double click on "Printer Spooler" in the Services list.
    c. click on stop, and then click OK.
    d. Click Start, type "% WINDIR%\system32\spool\printers" in the opened window and delete all the files in this folder.

    Step 2

    You must be logged on as administrator to perform these steps.

    a. open administrative tools by clicking the Start button, then Control Panel. In the search box, type administrative tools, and then click Administrative Tools.
    b. double-click on Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
    c. right-click on Print Spooler serviceand then click Properties.
    d. on the general tab, next to startup type, make sure that automatic is selected.
    f. e. the service is not already running, under Service status, click Start and then click OK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

    For more information, refer to the article below.

    Why can I not print?
    http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

    Method 3

    To identify and fix common printer problems in Windows, including print errors, errors of spooler for printing and other issues that could prevent you from printing, see the article help.

    Solve printer problems

    http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

    Kind regards

  • Bad or missing ink when printing or copying on HP all-in-one and color copier product families

    Click here for a description detailed steps for when colours or black are bad or missing when you print or copy on HP all-in-one and color copier product families.

    Determine if the problem is associated with cartridge

    1. the test report does not print correctly

    Check the estimated ink levels

    Check and clean the ink cartridges and the print carriage

    2. the test page prints correctly (for products only all-in-one)
    Step 1: Verify that the correct printer driver is selected in the software program
    Step 2: Restart the computer
    Step 3: Make sure that the correct printer driver is installed
    Step 4: Verify that printing in grayscale option is not selected
    Step 5: Select a color management profile
    Step 6: Determine if the problem is with the application software
    Step 7: Remove and then reinstall the all-in-one software

    Click on the laurels on the left side to help and click on accept as Solution to a solution. I work for HP.

    Best regards
    Kenneth

    I hope this helps!

Maybe you are looking for

  • Satellite Pro L300-152 and the task bar freezing

    Hello The taskbar seems to freeze whenever I use my laptop. I try to click on something like the volume and it freezes, I then gives me the option to restart windows Explorer, close windows Explorer, or waiting for the program to respond. Once it has

  • Vista - boot failure after installing Windows updates

    Hi, I use windows vista and for the last two days every time I shut down my computer, load 16 updates. Then when I restart my computer, it will start up repair and system restore. It would seem that these updates are causing a problem launching. 4 ar

  • I have a book on the step by step Microsoft Windows XP and I want to learn what are the practice files, and how are they used?

    Now I am learning something about this book that I have on the Microsoft Windows Xp step by step book, and I want to start learning what I need to learn, but I need you all to be a little patient with me here. If I make mistakes its because I am only

  • Endurance of weird mode?

    This morning, when I unplugged my phone that had nothing of the night, stamina mode showed me only 20 hours, while I could see up to 2 days on a few screenshots. My battery drains faster than that, but hey it's boring if I trust this estimate. Anyone

  • BlackBerry Z10 disorders to synchronise my email accounts

    I can't set up my email accounts in my BBZ10. Only the hotmail account can do. Others, gmail and yahoo is imposible to do. The BBZ repeatedly tell me the password of the account and the display shows a Board like this: your login information for the