CPU limitation with the new power supply

Similar Questions

• Dimension 4600 doesn't work with the new power supply

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Have you used the connector 4 pins, which was part of the 20 + 4 P1 12v connector, connect to the P2 4 motherboard connector pins 12v?

  
  See 41, J5B1 Connector [aka P2]

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-4600_service%20manual_en-us.PDF

  
   http://www.AOne.co.UK/prodinfo.asp?ProductID=4523

  Connector 4 + 4 pin 12v PSU is divided into two 4-pin connectors and one of them, can be used for the P2 motherboard connector.

  Bev.

• Pavilion NC768AA #ABA: HP Pavilion model. a6719f new video card with the new power supply?

  Hello!

  So, I won money to buy (hopefully) a new video card!

  However, I have a problem.

  I don't know which one to get!

  SO, someone please, please recommend a video card for intermediate level games.

  (My budget is less than $280)

  My PC has stock everything.

  Thus, it was purchased as it was when you would get everything first he.

  Yes, I need also a new power supply that is included with my budget.

  Thank you!

  Revionion, welcome to the forum.

  I'd be happy to help you in your choice.  The main problem is, recent video cards require UEFI in the motherboard instead of a standard BIOS to legacy.  HP didn't start using UEFI until mid-October 2012.  The latest maps not requiring UEFI were the series GTX 640.  However, MSI has made a card that has a VBIOS hybrid which can operate with a BIOS.  The best thing to do is to choose a video card you like and contact Technical Support from the manufacturer to ensure that it will work on your computer as it is almost 7 years old.  This will save you problems.  They are the experts on their cards.

  I like Corsair power supply units (PSU).  I suggest at least 500W.  This will give you plenty of power for any card that works in your computer.

  If you have any other questions, let me know.  I'll be happy to help you.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion p6-2: problems on blocking down after I installed the new power supply on a p6-2207ep

  Hi all

  B4 explaining my problem, I really don't know if I should post this in office, or material in this section of the freezes/crashes/locks but since I posted in freezing section and no results I decided to try here.

  My pc: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03382032

  I bought a new PSU: XFX TS 550W 80PLUS BRONZE for the GPU upgrade 380 R9 I was planning to do.

  Is there some BIOS I get HP for this cause of power supply from what I read, if I not only one of the things like manufacturer reset to the factory settings may stop working... Currently, my Bios version is 7.11...

  Problems with the new power supply:

  When I closed windows 7, the first problem, the picture freezes on the screen that says "blocking windows down", I waited a bit and nothing, tried to turn off the machine while keeping down the power button but nothing to disable directly in the rear switch of the PSU...

  Second time happened a little different soomething, seconds after freezing again on the screen that says "blocking windows down" windows actually turned off and the screen is off but everything inside the computer case continues to flow fans in light of the power button / stop and was also able to close by keeping pressed power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  Also tried the GPU with the new PSU fans worked but no entry in the screen that I guess just a power supply problem.

  ATM, I'm RMA waiting to know if it is a power supply defective or not...

  Problems after the reinstallation of the original material:

  Some of the same problems when I got the new PSU remained namely:

  Windows actually stop and the screen is off, but everything inside the computer case continues to flow fans in the light of the button on / off and was also able to close by keeping the power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  What I've done so far to try to fix the problem:

  Restore windows 7 to a b4 point the hardware installation.

  Reset the BIOS

  Hard reset

  Clean boot

  Do you have a full checkdisk which means 0 KB in bad sectors...

  A complete hardware checked all tests with the HP software

  A system file check everything beautiful

  What I fear most is a faulty PSU that may have caused damage to my equipment mainly the motherboard, but could be something else entirely.

  Maybe I need a specific BIOS for that motherboard / PSU combo, but after returning to the source material, the problems remained.

  What I can do because I can only make the software tests since I don't have an extra PC to test the parts...

  Hello

  Disconnect all external devices except the keyboard and mouse when you try to solve the problem.

  Disconnect the PC and removed the CMOS battery.  Press and hold the power for 30 seconds.  Now, replace the CMOS battery and plug the PC give a TI a go.

  Your PC is not stable enough to make a BIOS update. Do not attempt to use the graphics card XFX until your PC is stable enough to make a BIOS update.

• How to install the new power supply?

  OK firstly plug...

  Motherboard (motherboard): N-Alvorix-RS880-formfat (Alvorix)

  PC: HP p6703w

  new power supply: GS600

  new game card: evga gtx460

  OK I am experianced abit but still novice when they treat the upgrade myself. So here's my question...

  The mobo has a slot for 24pin power cable, but the current 250w ps uses a 20 pin in this slot. Is it safe for me to use all 24 pins for the ps (GS600) I want to? What was the reason why hp has used a 20 pins on this mobo? I don't want to fry my mobo. Laughing out loud.

  Thank you.

  Welcome to the HP Forum!

  ricofico wrote:

  OK firstly plug...

  Motherboard (motherboard): N-Alvorix-RS880-formfat (Alvorix)

  PC: HP p6703w

  new power supply: GS600

  new game card: evga gtx460

  OK I am experianced abit but still novice when they treat the upgrade myself. So here's my question...

  The mobo has a slot for 24pin power cable, but the current 250w ps uses a 20 pin in this slot. Is it safe for me to use all 24 pins for the ps (GS600) I want to? What was the reason why hp has used a 20 pins on this mobo? I don't want to fry my mobo. Laughing out loud.

  Thank you.

  It is safe for you to install the connector 24 pin. You are miscounting the pins on your motherboards ATX connector. The following image is your motherboard. I count 24 pins. Product specifications for your PC State that the PSU is ATX spec.

  

  Kind regards
  ERICO

• ASUS IPMTB-TK Pegatron card mother watt minimum / maximum specifications for the new power supply

  I need to get some update a new GPU card will need a bigger PSU but can't seem to find the specifications of power to my motherboard. I know that connections in the search of what power this motherboard is rated for.  Help, please! and thank you Asus Pegatron IPMTB-TK Intel x 58 Socket 1366 mATX

  Hello

  You should be able to use a power supply up to 650 watts.  I've seen a few posts on this forum where more than 650 Watt power supply would not work.  I have successfully used a Corsair HX650 with the same motherboard.

  You have some good recommendations for old_geekster and wb2001.

• Upgrading a p6510f Pavilion with a new power supply, graphics card and RAM work?

  Well, here's the deal that I go back to Japan for about 3 months and during this time I will borrow my laptop Cousins (in Exchange for my office) for Skype etc.. No problem their the thing is that he is a player and this p6510f has a few bad specifications when it comes to this, so I thought that I could let him borrow some cake rather than dirt, if you catch my drift ha... As well, when I get back gamer I ~ ('voice of Yoda"aka How Japanese works...)

  So I looked on Newegg / Amazon read comments and planned my purchase but the question is can this case and the Board of Directors manage what I use? lazy to measure everything out / busy.

  So first thing, I would like to replace:

  Replace the 2 x 2 GB ram cards default with:

  4 x Corsair blue Vengeance 4 GB (2 X 4 GB) 1600 mHz PC3-12800 DDR3 SDRAM of 240 pins

  For a total of ram 16 GB with my x 64 bit PC of course

  Link: http://AMZN.to/KtMt9m (note that I buy two)

  Replacing power 250w with an overkill rather one but it is the same price as a 550w then why not eh? After all the future upgrade/ability to use it in future builds?

  1 x Corsair Enthusiast Series 650 watts 80 Plus Bronze Certified Power Supply Compatible with Intel Core i3, i5, i7 and AMD platforms

  For the graphics card + overclocking.

  Link: http://AMZN.to/IkLTdp 

  Finally no more ATI integrated BS... Please for the love of the creator (will it work?)

  1 x EVGA GeForce GTX 580 1536 MB GDDR5 PCI-Express 2.0 2DVI/Mini-HDMI SLI

  If my PC can adapt to this card, and it works with power above that will make me happy enough. (Regarding the cooling if it becomes a problem, I can upgrade fans me but first comes this material.)

  Link: http://AMZN.to/IFiEa2

  I checked the slot for graphics card, RAM and power supply power and it seems to me that this will work out I want just a professional opinion...

  -----------------------------------------------

  Card not present upgraded

  HP Pavilion p6510f PC / Nr WW639AA #ABA

  Four cores AMD Athlon 630

  4 GB Ram DDR3

  HARD DRIVE 750 GB

  Integrated ATI Radeon graphics card...

  Power Max Power 250W

  Windows 7 Home Premium 64-bit

  -----------------------------------------------

  Thank you! ~ Of Amerindian

  Hello

  According to Corsair, the DIMMs that you chose is detected only at 1600 mhz, which is not in the specifications published by HP.

  You can roll the dice on the DIMMs that you chose, but I wouldn't recommend that buy you them until you contact Corsair and get a confirmation.  Computers HP can be very finicky with DIMMs, especially if you try to mix them with other DIMM modules.  If you do buy these bars and want to be them mixed with the existing DIMMs, then make sure the timings of latency CASE corresponding information validated HP. Also mix DIMM sizes will cause the memory function in unbalanced mode that adversely affect the performance of the memory.

  You should be able to make your own decision on whether to roll the dice.

• Problems with the DC Power supply QL 355TP: I can not set the tension level

  Hello

  I'm trying to control a power supply DC via GPIB. The power supply being used is the QL355TP of society Thurlby Thandar Instruments (TTi). There are no drivers of OR to control the instruments, then I need to download and install the driver from the website of TTi: the package I installed is as follows:

  "QL - P power supplies, (including QL Series II) series pilot National instruments (Labview and CVI)"

  and I also installed the following:

  "QL - P power supplies (including QL Series II) series, IVI driver"

  So, my problem is that when I try to use the sample application of the driver 'Volts.vi DC Ouput'; defines a specific level voltage, does not work properly. The application gives no error, but it is not set the specific level voltage. However, other functions work properly, as the measure or activate the output. I tried a lot of things, but I don't know why it does not work.

  I enclose the block diagram of the application and the front panel:

  

  

  I must say that I barely control instruments using Labview and is possible that this problem would be because I did not consider things basic and mandatory.

  Any help is appreciated.

  Thank you.

  p.s. Try to replace the decimal comma to period. It is possible that the driver does not correctly handle the comma.

• new power supply for a6319fh

  im going to be upgrading my diet so I can update my graphics card. the vehicle currently has a 250w power supply and I want to go between 450-600w. I need to know what brands will certainly adapt to my case. I have a processor intel dual core and im on vista sp1. also the new power supply will require an update of fan? any help will be greatly appreciated.

  Given that this case is an office of size, or it seems, you should be able to use a standard ATX power supply box.  To be sure, take it with you for the purpose of comparison or get the dimensions.  The fan is usually part of the diet, unless you want to say the "fan" which will probably still be OK, too.

• Installed a new power supply, run only windows XP.

  So I recently replaced my power supply, and all respect that seems to be going very well that the computer has no problem running. However, every time I start the computer, it start in Windows XP and immediately requires me a check on windows XP. A screen will appear asking if I would like to activate via phone or internet tool. If I use the online detection tool, he suggests, he says that I can not connect to the internet and sends me in return. If I call the number, I can possibly a recording of the voice asking me the code 40 numbers on my screen. Whenever I enter this code by phone, he says he does not recognize that code and I'm at square one. So basically, how can I get my computer to start as it has always, in Windows 7 and with all my usual data?

  Also, I tried to start in safe mode with command prompt. When I get to the menu Startup and recovery in system properties, it appears the only operating system default is "Windows XP Media Center Edition. I have several hard drives my best guess is that it maintains launch than bad. Any help find how launch of correct would be greatly appreciated.

  TLDR; New power supply, computer guard run windows xp and by asking for activation, when I was previously with windows 7 for more than a year.

  Good guess:

  When you have reconnected all cables in your PC after installing the new power supply, you connected the SATA (data) cable that should go to your primary (generally marked 0) SATA port for a hard drive that has Windows XP on it.

  Check your cables.

• My new power supply work with my motherboard?

  Hello

  I reasontly bourght a few upgrades for my PC.

  I bourght an i7 870 and an AMD 5670 + a new power supply

  So my question, what ive in doubt, my new PSU(CX-500) work with my motherboad (MS-7613(Lona-GL8E)?

  Thanks in advance

  René Tyrsted

  Thank you.

  Yes. It will work.

  However you will probably find a little tight because of remaining unused cable bundles. My preference for the PC ATX Mid-size boxes are of the modular power supply. With a modular power supply connect only s connector as much as you want.

  Do the upgrades one at a time.  Start with the power SUPPLY and any other origin. Check that it works and then close.  Then go to the graphics card.

  Happy update.

  Best regards
  ERICO

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• Can power supply Question - I use the 230W power supply with a W540?

  I have a W540, which currently uses a power 170W (8.5 a 20V)

  I got also a docking station for a P50 that has a power of 230W showing 20V 11. 5a.

  The connectors are similar, but I'm hesitant to try the 230W power supply in the W540.

  It is allowed to use the 230W power supply with the W540?

  230 watts is maximum power feeding, it only provides the energy required by the computer.

  I sold my W540, so I can't test it for you. But I do use the ThinkPad X 1 carbon with 230 watts without no problem power adapter.

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Does not start with the new graphics card

  Hello. I have a P7-1058uk Pavilion Cleveland-GL8 motherboard with integrated graphics.

  I bought a new monitor that has resolution 2560 x 1440, equal the integrated graphics card can face if tried to to level with a Gigabyte GT630 card.

  When I start, I have now the chance to the blue HP screen but not more details. If I start with F10 or ESC key, I get a black screen instead. Whatever it is, I am asked to press ESC to enter in the start, but by pressing on the button has no effect and the computer just hangs. There is a cycle repeated very quiet click that sounds like the disk drive HARD trying to start then stop

  If I remove the graphics card and connect the monitor to the integrated graphics card then all's well again (but limited to the resolution 1920 x 1080).

  Perhaps foolishly, I assumed it was a problem with the residual power (300W) and not enough punch power to run the HARD drive. But who, after having upgraded to 650W it makes no difference. I also tried to download the NVidia drivers but it won't let me install because I can't get the computer to work without the graphics card and Nvidia install it because it cannot detect the hardware.

  Any ideas/help would be appreciated.

  Andrew

  You can have one of these motherboards that are not happy with NVIDIA graphics cards.

  This may sound a little weird, but it happens.

  The other possibility is that you have damaged your home x - 16 PCI Express by installing a map requiring more that the installed power supply has been able to provide.

  Kind regards

  ERICO