CQ62-410US stuck with "Several monitor - Clone View" and VGA port does not

Hello!

I have a Compaq CQ62-410US computer laptop with an Intel GMA 4500 M (onboard) video card and a port output VGA, Windows 7 x 64 operating system. A few weeks back the screen was broken (kick straight punch of a child) and nothing could be transmitted via the VGA output either, but the laptop booted and I could hear the sound of Windows 7 logon. I never checked before the VGA output port.
Yesterday, I replaced the screen broke up with and identical. The fine (full-screen) display in case of back work (boot from USB Flash and the sea + test images), but in Windows 7, two vertical black stripes appeared on the sides because lower than the native resolution. The resolution can be changed at native 1366 x 768 "Screen resolution" because the display is set by default to "Multiple monitors" (I have no other monitor connected, only the built-in screen) and "display of Clone. The built-in display is set as secondary and 'Generic non - PnP' is defined as primary. Any attempt to set the integrated display as primary function or to change the mode "display single" / "Extend view" leads to a black screen with the backlight always on, no matter where I change the settings - in the 'screen Resolution' or 'Graphic properties' (from driver Intel). In the 'Screen Resolution' window the pictogram of the screens show a single screen split in two, and when I press the button "Identify" it shows on the screen ' 1 | 2 ", as you left half of the screen is the main display and half right is the secondary display.
I put a Philips monitor to the VGA port, Windows detects and installs the appropriate driver, but there is no picture any of mode I put - Clone, Extend, unique display - monitor.
I tested 3 view of the site of Compaq drivers for my device and the GMA 4500 M drivers from Intel, but the problem is the same (with the drivers from the site intel, on I get only black screen with backlighting.) Pilots are unstable, sometimes at the opening session, page is only a black screen (but before the windows loading screen appear very well) that cannot be changed by "Fn + F4" / "F4" (change view) but a black with the backlight is turned off.
Due to the replacement of the hard disk, I can't use restore of the operating system that is installed at the factory.
Please advise me how to solve the display problem and enable the port VGA (get the image on the external monitor).
Thank you in advance.
SSM there is not output through the VGA input even at the BIOS screen (no material or to issue independent of the operating system support?).

I have attached a screenshot.

Update: I started a live Knoppix CD, and I don't find any problem - unique in 1366 x 768 display configuration; I could even play a game in 3D (OpenGL). While hanging from one monitor to the VGA port, it was found, but when trying to print image to it the OS hung. I guess it's a hardware problem, something to do with the video controller.

I thought about it, it's the GPU, I think that some of the contacts are damaged. Today even in the BIOS screen I see in the middle of the screen a vertical thin purple line which was bounded two screens on a single screen, and all now have a purple tint.

I had a quick glance at the GPU and surprise - it is glued to the motherboard, no sleeve, no welding. The motherboard chipset is also stuck.

See the attached images.

Thank you for the excellent support. I will never buy anything with Compaq logo on it.

Tags: Notebooks

Similar Questions

  • script with several SET options on a single line does not

    I have a script that worked very well on the 4.0.3 version but now in 4.1.0.19, he's not taking my SET options. Simple test case:

    TOGETHER TO CHECK OUT LONG PAGES 350 LINES 500 1000 CUT OFF ECHO FEED

    SELECT RPAD('&val1',100,'Y') FROM DUAL;

    < F5 >

    SP2-0158: unknown SET "check" option

    old: SELECT RPAD('&val1',100,'Y') FROM DUAL

    New: SELECT RPAD('a',100,'Y') FROM DUAL

    RPAD ('A', 100, 'Y')

    --------------------------------------------------------------------------------

    aYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

    YYYYYYYYYYYYYYYYYYYY

    (Size of the default line to 80 characters and show the SQL text for the substitution of the value of the variable)

    It seems to work fine if I use several SET commands

    SET VERIFY OFF

    500 FIXED LINES

    SELECT RPAD('&val1',100,'Y') FROM DUAL;

    RPAD ('B', 100, 'Y')

    ----------------------------------------------------------------------------------------------------

    BYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

    Is it a bug or a feature in version 4.1?

    I do not use a login.sql (Tools > database > Startup Script is not defined)

    SQL Developer Version 4.1.0.19

    Build a HAND - 19.07

    It is an interesting question.  Of course, SQL * more actually accepts a SET command listing several pairs of variable/value system

    Despite the fact that recent literature does not promise this syntax of management and only mentions the VALUE...

    https://docs.Oracle.com/CD/E11882_01/server.112/e16604/ch_twelve039.htm#i2698538

    .. then by the summary of all the variables SET system...

    https://docs.Oracle.com/CD/E11882_01/server.112/e16604/ch_twelve040.htm

    Check the bug list, I see a fix in 4.1.0 for the case of variable/value pairs 3 (with no error message), but failing to put the last 2 variables correctly.

    By checking your test scenario against 4.1.0 and the last line of the main code, it also works for the first 4 variable/value pairs...

    all check out along lines of 1000 pages 350 500

    then complained to carve out on being the fifth...

    game check long 1000 350 lines of topping on 500 pages

    line 1: "game of topping on ' is obsolete.

    and finally the errors to try to manage any valid system variable after the fourth...

    game check long 1000 pages 350 lines 500 feed

    SP2-0158: unknown SET "check" option

    game check long 1000 pages 350 lines 500 topping on feed off echo off

    SP2-0158: unknown SET "check" option

    Buggy.

  • Satellite U300 - 13 M - port external monitor (VGA port) does not work

    Dear users of Forums from Toshiba,

    I have a problem with the VGA port. I use the Windows XP operating system. Laptop, do not display on an external monitor, I tried all monitors to connect to my office, but does not solve this problem. I also tried to reinstall Windows XP, once again, and nothing has changed.

    Please help me.

    Best regards, Elbrus

    Hello

    I guess that by Satellite U300 came preinstalled with Vista. Am I right about that?
    Anyway, if you want to use external monitor and switch successfully to him you must install the utilities and tools of Toshiba. There are several of them and allows you to use the FN + F5 key combination and move your desktop to laptop LCD display to the external monitor.

    Can you please tell me one thing: have you installed all the stuff of the Toshiba download page according to document Instructions of facilities?
    The configuration of the laptop is not known to me, but try please check the Intel properties and let me know if the external monitor is recognized in properties. Usually, you can choose to use the external monitor there.

    You can also start Toshiba HWsetup utility. There must be tab display. There you can also find an option to use the LCD screen + monitor at startup.

    Check it out please and post the results.

  • How can I download the new update on my Macbook pro when the password is not working? When I connect to the Adobe site with the same user name and password it DOES not work. I don't understand why.

    So I have a macbook pro - and she advised me that I had to update my Adobe flash player. So I go through all the steps and I'm stuck at the last stage, where he asks me my user name and password. I go in there correctly - several times and it does NOT connect. He shakes to show that there's an error. Double check my file AND I go to the Adobe site to connect with the same information. and it works very well.

    WHAT IS THE PROBLEM? Help please.

    Could you please try ComputerName administrator as username and the password as password.

    I hope this works.

    Concerning

    Hervé Khare

  • Clone Stamp and Healing Brush does not

    I also have problems with the Healing Brush tool and the Clone Stamp tool

    I am running Windows 7 (64 bit on a powerful computer with 6 GB of Ram and pleanty of HARD disk space.)

    I use the mouse cable and do not have a connected tablet.

    I duplicated the background as a background copy crazy ab\nd the invisible ther background layer copy backgound is selected and is made visible.

    By clicking on the tool or the other, I move the cursor to the source area I wish to clone of and [Alt] - click. I then try the slider on the destination area, the part I want to cover up with material in the source area of love.

    What is happening is the entire image moves showing that I move the mouse, revealing another image below that does not move.

    Either I don't understand what these tools are supposed to do, (I doubt that because I used this tool several times in PSE 6 without problems) or there is something terribly wrong with the program.

    I have underststand fronm reading the forums that the same problem exists in CS4.

    I checked the updates, but the only update I have not downloaded and installed is supported for recent cameras Raw files.

    PS Files that I'm getting are the original JPGs and have not been converted to any other type of file.

    Here is a page illustrating the offbeat image.

    PSE Prob.JPG

    Thanks for any help you can offer.

    BTW, Adobe do support this program? I can only find help this kind of help in the forums.

    It looks like what your seeing is the clone source overlay.

    With the selected clone tool, click the icon highlighted in red

    and set the options as shown below.

    MTSTUNER

  • HP laptop - 14-r113tu: HP - 14-r113tu with Windows 7 32 bit laptop (USB Port does not)

    Hi guys,.

    I'm from the India. I recently bought "HP laptop - 14-r113tu ' with windows OS 8.1.     But, I do not earn 8.1, I love windows 7. So I desided to degrade the operating system. And also I have successfully install windows 7 32 bit on my noteboot. But, problem with USB Port not woking and everything. I'm trying to install the driver chipset here, laptop Hp 14 14-r113tu drivers. But only find drivers for win 7 64 bit. I install windows 7 32 bit. I don't know what to do! ??

    can I find win 7 32-bit drivers for my "Hp 14 notebook pc 14-r113tu"

    or how can I enable the usb ports? Please help guys...

    Hello:

    Chipset: Second listed file is the auto install file.

    https://Downloadcenter.Intel.com/download/20775/Intel-chipset-device-software-INF-Update-utility-

    Graphics card:

    https://Downloadcenter.Intel.com/download/24972/Intel-HD-graphics-driver-for-Windows-7-8-8-1-32-bit

    USB3: (64 bit 32 bit files file has too).

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6431933&swItemId=ob_132256_1&swEnvOid=4059

    Audio: Accept the agreement.  Download and install the driver first on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=24&level=4&Conn=3&DownTypeID=3&GETDOWN=false

    Ethernet: Download and install the driver for the second on the list:

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

    Card reader: download and install the driver first on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

    Wireless:

    http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_147415_1

    Bluetooth:

    http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_147650_1

  • With recent updates, restoring with restore points is more and now IE does not work properly.

    I just had a few security updates for my machine and now there is no restore points, restore reports again that restore points are invalid, try another date of restoration (I'm guessing on this one).  Internet Explore ceased operation (for denial of service in IE error messages).  Norton finds nothing.  Any suggestions?  P.S. I don't browse the internet, check e-mail, or any other activity on this machine and only play an internet game on it.  Any suggestions or helpful hints before moving a complete system recovery disc?

    You used the word "n" and system restore in the same paragraph.  It's a good sign for boredom.

    Here are a few known issues in SR and Norton, you can read and see if they will work for you.  It is possible that your SR will never work unless you reinstall the system restore (not XP - just the system restore part) which would mean you would lose all your old PHI from scratch with new RPs.

    I can't help you with your IE, but if you provide the following information, maybe someone else can.

    SR already worked successfully for you in the past?

    What is your system brand and model?

    What is your Version of XP and the Service Pack?

    What is your version of Internet Explorer?

    You have a different browser like Firefox or Chrome that operate and is only IE afflicted?

    See if IE will work if you click on start, programs, accessories, System Tools, Internet Explorer (No Add-ons).

    What is the exact error that you see when you try to use IE?

    Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..
    What is the issue that you are experiencing that you think that the system restore will be remedied (or you are just convenient)?  System Restore is not a time machine.
    Some tools Anti Virus 'protect' your system so that they will not allow a restore of the system work properly.
    For example, if you use Norton/Symantec products, you will see a message like this:
    Restoration incomplete. Your computer cannot be restored...
    It is also a popular Symantec problem (well, I'll be polite and call an "undocumented feature"...), they wrote an article about it:
    According to what you use for malware protection, you may need to disable the product temporarily, do the system restore and then turn the products light up again when the system restore is complete.
    Sometimes you need start your system in Mode safe and so that your protection programs are not running, and then do the system restore.  Tips from Microsoft in some of their articles that if the system restore does not restore your computer, start in Safe Mode, and then run the system restore.  It works for some configurations.
    System Restore is sometimes so afflicted or Restore Points are suspicious, the best solution is to reinstall your system restore.  This will remove the old Restore Points, but sometimes it's the only way to fix a broken system restore.  You don't have to reinstall XP, only the part of system restore.
    That can leave you with your problem of unspecified origin that you hope the system restore will fix (using a system restore is usually not equivalent to fixing the problem though).
    Give these ideas some consideration if they apply to you.

    I would like to deal with the problem as if there was no such thing as the system restore, fix your other questions, stabilizes, then get your SR works after that.  Certainly, it should work well, but I wouldn't count on it as a way to solve problems.

  • VCB with Windows 2000 Server before and after! Does not!

    In our configuration (esx3.5, vi2.5 and vcb 1.5) we have problems get the pre post scripts running in Windows 2000 Server. It does not at all pre/start scripts. We need this because we have some strange databases that must be stopped before the snapshot and started after.

    The 2000 machine is fully updated, and the esx servers are updated 4.

    I also tried in a test environment with esx3i fully updated (beyond update 4) and vcb1.1

    Pre-Post controls work perfectly in 2003 (not yet tested in 2008).

    What I tried:

    • Disable-ing the SyncDriver (must be a solution for Server 2000 with Exchange 2000)

    • Place scripts to a location different (C:\WINNT or C:\Windows or C:\Program VMware Tools\backupScripts.d

    • Adding C:\Program VMware Tools\backupScripts.d to the $PATH variable so that the script can be run from anywhere

    • Reinstall the VMWare tools.

    The command I used to get the backup:

    v h vcbMounter.exe *. n u .local \n*-ipaddr:vcbtest. .local - r c:\vcb\vcbtest-full-01 t m nbd fullvm

    I also tried adding the switch "0 q" or "q 1".

    No solutions seem to work. Does anyone have any ideas?

    Greetinx Atze

    It works for me with a C:\Windows folder (even if windows is installed in C:\winnt),

    with files like pre-antigel - script.bat and post-thaw - script.bat

  • 'Open the link in a new tab' does not work. I tried with all disabled add-ons and it still does not work.

    When I right-click a link and select 'open in a new tab' and 'opens in a new window', nothing happens. In addition, nothing happens when I type a query in the search bar and press ENTER. I tried to restart firefox in safe mode and disabling all add-ons, but the problems continue.

    The setting in "tools > Options > tabs: open new windows in a new tab instead" is for links that specify a target window (for example, target = _blank) to open the link.
    This option allows to divert these links into a new tab instead of a new window.
    Links that do not specify a target always open in the current tab, unless you redefine that with a middle-click or Ctrl (Mac: Cmd) left click (new tab) or a left click UPDATE (new window) or via the context menu.

    You can check if you have the XML files including Google's default search engine in the browser\searchplugins file in the Firefox program folder.

    If this isn't the case, then you need to reinstall Firefox.

    Try to delete the file search.json and possible search - metadata.json and search.sqlite files in the profile folder of Firefox to reset the default search engines.
    You can use this button to go to the Firefox profile folder currently in use:

    Firefox will rebuild the file search.json from the default search engines in the folder "browser\searchplugins" in the Firefox program folder and the searchplugins folder in the Firefox profile folder.

  • I'm stuck with several GB of music files on my phone and I can't get down them!

    The other day I tried to install an application on my phone, but I didn't have enough memory.  My phone is full of music via iTunes synchronisation dock. So I connected it to my computer to try to make some more room. But there is a problem.

    (1) Apple does not play nice with Palm. Synchronization is no longer permissible or possible. I can't use iTunes to manage/delete music.

    (2) in USB Mode, there is no way to access/view the library. It's just not there.

    I tried Palm support, and they confirmed that the USB Mode is not working. I guess that the library is located in a hidden folder or directory. They suggested that I downgrade my iTunes. Goal that is unacceptable to me because one) it forces me to break the license Apple, b) it is not taken in charge, and c) if there is still a remote chance it will mess up my iTunes library, I won't.

    I'm ready to get off at Palm headquarters and throw my phone to their building.

    Can someone tell me how to delete my library without hacking iTunes?

    I thought about it. Support, put this in your KB. Everyone who was sync via iTunes on a Mac is currently STUCK with several GB of music on their phone that they cannot manage or remove, which makes the Palm Pre a lot less useful than announced.

    USB mode is a waste of time for people on a Mac. These hidden files are never going to be visible, and the library cannot be removed. The solution: go through a PC. Anywhere, any PC will do. Connect your phone to the PC, go to the USB drive Mode and show hidden files, then delete them from there.

    I got an old laptop lying around at the bottom, and the problem was solved lickety split.

  • Fields on several Internet sites have been changed in another language. The browser is set to English, and this problem does not occur with Chrome.

    Fields on several Internet sites have been changed in another language. The browser is set to English, and this problem does not occur with Chrome. Specifically, a large part of Tumblr and Facebook menu has been changed in another language (Russian, I think). I tried reinstall Firefox, clear the cache and reset firefox to its default state. None of them helped. Any suggestions on how to fix this?

    Hey again,

    Sometimes a problem with Firefox can be a result of malware installed on your computer, you may not be aware of.

    You can try these free programs to search for malicious software that work with your existing anti-virus software:

    Microsoft Security Essentials is a good permanent antivirus for Windows 7/Vista/XP, if you do not already have one.

    More information can be found in the article troubleshooting Firefox problems caused by malware .

    I hope this helps!

    Curtis

  • Portege M200: serial port does not work with port replicator

    Hello
    I have a Tablet m200 and the top mentioned dock/replication PA3314-1PRP port.
    As the M200 has no serial port (rs232), I want to use the one on the docking station, but it is not recognized as a device on my tablet.

    Thew network connections and usb ports all work fine and the lpt port is shown in Device Manager. I have restored the Tablet and it still does not recognize the serial port.
    How can I get this port recognized so that I can use it.

    Thank you very much
    Lee

    Hello Lee

    I just, I can confirm that when you use the Replicator port advanced III with Portege M200 several ports do not work. Problem is that Portege M200 does not support these interfaces.

    This is a technical limitation and the port of mouse PS/2 port keyboard PS/2, serial port, I.Link (Firewire) port and DVI port will not be supported when Portege M200 is anchored on the Advanced Port Replicator III. :(

  • I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

    I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

    Hello

    1. what operating system is installed on the computer?
    2. what web browser are you using to play the games online?
    3. don't you make changes to the computer before the show?

    If you use Internet Explorer, then I suggest you to try the steps from the following link:

    The problems of games online using Internet Explorer
    http://support.Microsoft.com/kb/2528246

    Additional information:

    Why my screen is black when I start Windows 7?
    http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

    Solve game problems
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-game-problems

    The problems of the game performance
    http://Windows.Microsoft.com/en-us/Windows-Vista/fixing-game-performance-problems

    Troubleshoot display with Microsoft games
    http://support.Microsoft.com/kb/263039

  • How can I get my photos from Windows Gallery to view and print in color, not just black and white?

    How can I get my Windows Gallery pictures to view and print in chiputa, not just black and white?

    Hi Petergrossman,

    Welcome to the Microsoft Vista answers Forum!

    I need few details about the question you posted.

    * What are the name and model of the printer?
    * You receive driver updates for your printer through Windows Update?
    * The printer prints the other applications in color?

    In the meantime, try the following steps.
     
    1. try to print the default pictures in Windows Photo Gallery and check if you get a printing color.
     
    2. try to uninstall the printer driver and reinstall it.

    Also check the setting of the color of the printer. Go to printer settings and make sure that you have selected the option to color.

    To print a picture, follow these steps: -.

    If you have a printer connected to your computer, you can make prints of digital photos. The quality of your photos depends on several factors, including the type of printer paper, ink and the settings of the printer of your choice. You can control many of these settings when you print the picture, but keep in mind that the overall quality and resolution of the digital picture you are printing will affect your final result.

    1. open Windows Photo Gallery by clicking on the Start button, all programs, and then clicking Windows Photo Gallery.

    2. click on the image you want to print.

    To select more than one picture, hold down the CTRL key while you click the pictures that you want to select.

    3. on the toolbar, click on print and then click on print.

    4. in the print pictures dialog box, select the printer, paper size, qualite quality print, style print and number of copies to print.

    5. When you have finished choosing how you want to print your photos, click Print to start printing.

    Choose printing options follow these steps: -.

    Before you send a print job to the printer, decide if you want to print all or part of the document or Web page. You may, for example, annotate the pages to print or select a part of a document before sending it to the printer.

    Here are common printing tasks to consider:

    1. to print that a hollering part of a document or a file, make a note of the page numbers for each page you want to print.
    2. If you want to print part of a page or a Web page only, select the content to print before printing.
    3. If you want to print a specific page, click anywhere on the page before choosing the print options for the document.
    4. the page that you clicked becomes the current page and you can print it by selecting this option in the print dialog box.

    After deciding what to print, choose how the print copies should look, and then select a printer.
    Use print preview

    To see what the print will look like before you print it, open the document in a program that offers a preview before printing. Print preview is generally located in the file menu of a program. You should be able to get an overview of each page of the document. In some programs, you can choose print in preview mode options and then print directly from the preview. In other programs, you will need to close the preview, change the document or your printer settings and print.

    If you preview or print a document, and it does not appear the way that you intended, you will need to change the document or change your print options. For example, if one part of your document fits on the printed page, you may need to reduce the font size, reduce the margins, or change the page layout and then try to print again.

    Check out these links that talk about how to print a picture using Windows Photo Gallery:

    http://Windows.Microsoft.com/en-us/Windows-Vista/print-a-picture

    http://Windows.Microsoft.com/en-us/Windows-Vista/choosing-print-options#section_2

    Thank you, and in what concerns:
    Shalini Surana - Microsoft technical support.
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Problem with wireless - Vista Network and Sharing Center does not recognize my connection!

    I use the Home Visa software and my network and sharing Center does not recognize my connection but I can access the internet without any problem. Previously, I was using a wireless router Linksys with an old box of AT & T internet with no problems. The problems started after I updated my AT & T internet box that made obsolete the linksys router and now the network share does not connect. I just have the problem of getting the network and sharing device recognizing that I am actually connected to a wireless network. I can't use my printer or share files with other people. I can't get my wireless printer to work if I restart my computer and I have the documents I want printed already sent to the printer. My network and sharing Center also works very well for a few seconds when I start my computer then it turns off again.

    Hello

    Method 1:

    Windows wireless and wired network connection problems

    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Method 2:

    You can also view the related items for more information.
    The problems of Internet connection

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

    Network connection problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

    Solve problems, find wireless networks

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

    Method 3:

    Setting up a wireless network

    http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

    Wireless network card: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

    See also:

    Connect to a network with Windows Vista wireless

    http://TechNet.Microsoft.com/en-us/library/bb878035.aspx

Maybe you are looking for

  • Icon on 4s to mail, do not see the number of mails

    On my iPhone 4s, the icon of mail to the row at the bottom of the screen, are always shown (for example) 2, 3, 4 etc emails to read. This indicator has disappeared recently. Is it possible to fix it? I don't have this problem with my iPad, and both a

  • Unable to install add-ons

    When you try to install a new Add On I get message "You need Firefox to install add-ons." and add to the occult Firefox button. Frustrating, because it is already installed of course to access the page in the first place!

  • SDHC 4 GB and Ricoh Cardreader does not work

    When I insert a 4 GB SDHC card in the internal card reader system is not able to read, It wants to format. An old 64 MB SD card is well read and with additional USB card reader, I can read these 4 GB cards. What can I do now? Thank you for yor help.

  • Reinstall the power interrupted while win7, how to continue?

    When I turn on again, there is error message saying need to restart, after that reboot it is the same error message. I have a copy of linux, and if I install that first he would eliminate the content current window and I can reinstall win7?

  • Xperia Z3C issue after the transfer of applications on SD card

    Hey guys, hoping you can give me a little help here. I've updated my Xperia Z3C to Lollipop the other day, which was until now very well, but last night I moved a few apps to my SD card to free up some of the internal memory of my phone (do not use a