Crashing - Satellite A200-171 with Vista Home

Similar Questions

• Satellite A200-1vp with Vista - code 39 of the CD/DVD drive failure

  Hello

  I was burning and watch DVDs on my Satellite A200 - 1 VP, with vista, since February, the last time I burned anything was a couple of weeks.

  Suddenly, there is a problem, no response when I insert a disc and my divx player says me no recorder found.

  When I am looking in the Device Manager I get the message 'windows cannot load the driver for this hardware' (code 39) "driver is damaged or missing.

  I tried to uninstall it and using the limit filter upper/lower of Toshiba, repair tool but on restart it still cannot install.

  Should I try the Toshiba Recovery Disc and lose a lot of that programs/files, as a last resort?
  Would this work?
  Anyone have any ideas?

  Here's an interesting article from Microsoft Knowledge:
  http://support.Microsoft.com/kb/270008/en-us

  You must first access the Device Manager and should remove the reader of CD/DVD from the list of devices.
  Then should access the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Reboot the laptop and check if the CD/DVD drive would work again!

• 0x8007001b with Vista Home Premium Center backup and restore backup failure

  I have my Toshiba Satellite M205-S7452 with Vista Home Premium for about 8 months, and November 2007, backup windows, and restore program worked flawlessly. I was able to back up my music, photos and documents to a DVD on a regular basis. But then I started having an error halfway back up that says "drive cannot find the sector requested" with the 0x8007001b error code. It seems that the backup works partially - there are files on the DVD player but I don't know if it ends or not. I tried to do some research on Google and it seems that there is other people affected by this error, but I could not find suggested patches.

  Hi jennielah,

  Please use the Forum of the community for Vista.

  If it has started, use the system restore back to a point before you start. See below for instructions.

  If you can do that I have a work around you. Your specific error seems to relate to update failures, not only the Windows updates but the various failures of update.

  The job is to save it to your hard drive and copy the files on the DVD after the fact.

  I hope this helps.

  Please let us know if we can do something else.

  The System Restore tool

  Other troubleshooting methods, such as using the System File Checker tool, cannot solve the problem. If they do not resolve the problem, and the problem you are experiencing started occurring recently, you can use the System Restore tool. Using this tool, you can restore the computer to an earlier point in time.

  The tool using System Restore may not necessarily help you determine the problem. The System Restore tool uses points of restore to return the system files and settings to an earlier point in time. You can use it to restore the operating system to a point in time where you have not experienced the problem. When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start , type system restore in the Search box, and then click System Restore in the programs list.

  If you are prompted for an administrator password or a confirmation, type your password or click continue .

  1. In the System Restore dialog box, click choose a different restore point , and then click Next .

  2. In the list of restore points, click a restore point created before you started having the problem, and then click Next .

  3. Click Finish .

     The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Here is a link to the system restore, if you would like more information

  http://support.Microsoft.com/kb/936212/

  Matt Hudson
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Would Satellite U300-11V running Vista Home Premium 64?

  Hi all

  I have a Toshiba Satellite U300-11V

  The laptop came with Vista Home Premium (32) and I would like to upgrade to the 64-bit version and I wonder if my hardware is actually compatible with it.

  I tried the Windows Vista Upgrade Advisor, but that had nothing to do with 32 vs 64...

  You can find the full specifications of my laptop to the:
  http://UK.computers.Toshiba-Europe.com/innovation/JSP/SUPPORTSECTION/discontinuedProductPage.do?PRODUCT_ID=132428&disc _ MODEL = 1 & service = UK & tab = 2 #2

  Any suggestion would be deeply appreciated

  Kind regards
  R

  Of course, it s compatible with Vista 64 bit OS.
  Satellite U300-11V belongs to the series of PSU30E.
  I checked the European driver Toshiba page if a 64 bit Vista drivers are available, but unfortunately, they are not released.

  However, you would be able to install Vista 64-bit on your laptop, but you have to collect the drivers Vista 64 bit unique from other series of laptop.

  Several series of laptops are equipped with the same features and sometimes, you can use the same drivers on different laptops.

• Strange problem with Vista Home premium configuration update

  Just bought a Toshiba Satellite Pro L300-1AI which was preloaded with Vista Home Premium.

  Clicked on configure updates on the front screen and he entered a loop that says: Configuring updates: stage 3 of 3-0% complete. Do not turn off your computer.

  Every 5 minutes or so then stops and restarts with the same message. I left on for 8 hours, so can not believe he needs for this long. Just tried to set off, but when you restart it defaults as shown above.

  Please advise... even if you can get me right back to the normal screen before

  Hello

  Try please start your computer in safe mode and restore your operating system to an earlier time (before the update). Maybe this will help.

  In the future be careful with updates. I recommend you to disable the automatic update. Just check the list with updated supply and install important and recommended only. Disable all optional updates. You don't need them.

• Satellite P100-160 with Vista: No TV-OUT after downgrade to XP

  Hi guys hope you can help me out here...

  I recently bought a laptop (satellite p100-160) with Vista on it to know that it was not compatible with wot I bought dethrone so I decided to downgarde for XP Home Edition... Solange decommissioning that I had to install a few drivers like there's do and everything went well...

  Anyway, a few weeks later (yesterday), I went to watch a movie and when I pluged in my tv out cable, I have nothing. I tried to unplug and plug in again a few times but still nothing, it normally switches on in about 20 seconds... So im guessing that either I need to a driver or a Summit.

  Can someone help me out here?

  Thanks a lot

  You n t need a special driver to use the s-video port.
  You must install only the compatible graphics driver.

  How have you tried to switch to the TV device?
  Have you used the FN + F5 key combination?
  You should do this.

  Connect the TV to the laptop using the s-video port. Then select the s-video on the TV and choose the right channel.
  Press the FN + F5 several times until you get a picture on the TV.

  Please note; Don t start the DVD software like DVD win until you have not enabled on TV!

• Re: Satellite A300-145 with Vista 32 maximum RAM?

  Hi all!

  I have satellite A300-145 with Vista 32 home Premimume - now on laptop installed 2 modules of 1 GB of RAM (for mode dual channel)

  Q: if I replace the RAM to 2 modules of 2 GB of RAM this mode dual channel still & 4 GB RAM?
  -May support A300-145 4 GB RAM? and Vista 32? (Intel GM965 chipset have support 4GB RAM)

  Hello

  Satellite A300-145 was equipped with a Mobile Intel GL960 Express Chipset. Or I m wrong?
  AFAIK this chipset provides only the 2 GB support

  > If I replace the RAM to 2 modules of 2 GB of RAM this mode dual channel still & 4 GB RAM?
  32 bit Vista will recognize only about 3.2 GB.

• Satellite A200 - 19L with WinXP OS - key Fn Visual control

  Hi all

  I have Toshiba Satellite A200 - 19L with OS WinXP (I found all drivers), but have a little problem with it:

  With previous (event with this under Win VISTA) Toshiba laptops when I was doing operations with a combination of Fn keys (for example Fn + F5 - for then between the LCD screen and an external display or a projector) I could see a few icons on the screen (for the example above, a series of 3 icons representing the LCD displays only the LCD + external display) External display only; the same was hapenning when you use Fn + F6 or F7 - brightness - I saw the brightness icon and a cursor moving upwards or downwards according to the used key combination).

  Now, with the XP drivers on my laptop, I have absolutely to the specific features of the Fn key combinations but HAVE a no. VISUAL CONTROL of them.

  Does anyone know HOW can I restore on the computer?

  Thank you guys!

  I have the same problem. It worked before, until
  probably a windows update has been mess up with the function FN + F5.
  I tried to update the driver for the graphics card from NVIDIA. Who knows...
  I try so many things, but it does not work.

  When I press FN + F5, I have only the choice with the icon of the LCD screen. Until I'm OCR a and OCR + LCD screen (they disappeared).
  I wrote to TOSHIBA, but no response. I read on many forums that much laptop Toshiba you have this problem.

  Could someone help us?
  Thank you

• comatibility professional version 5 Visio with vista home premium

  I have a Toshiba satellite lapto, that came with vista home premium. I installed visio 5 vesrson profession. But id does not run. I get a message saying that the problem of compatibility. What is happenning?

  Hello

  always check the compatibility of vista programs on the link below

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  If a program is compatible with vista you can try right click on the setup.exe, and then selecting run as administrator

  It is not compatible with vista, you can try running it in a previous operating system mode

  This does not work for all programs

  read the information below

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  If a program is particularly important to you, there is this way of trying

  but it's expensive, because you must have a previous operating system license to install

  This method also works in vista Home premium, BUT is not supported by microsoft

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=04d26402-3199-48A3-afa2-2dc0b40a73b6&displaylang=en

• 64 bit sytem with vista home premium which has been randomly locking up and freezing. The error is event 6008.

  I have an ACER aspire x 3200 64 bit sytem with vista home premium which has been randomly locking up and freezing. The only mistakes were event 6008 with a description of the stop system prior to (time) on (date) was not planned.
  When these errors originally occurred, I returned the system to acer and they installed a new hard drive. After updating the vista system blockages continue 30 times over a period of 3 months. Acer sent me a new disk image on 3 disks that I have installed and updated on 11 October. There is no blocking until the 10/27, 10/28, and for the 3rd time today.
  The closed unexpected gives a blue screen if I use the locking system to the top. I have to hold the power to restart when the system crashes.
  Can someone help me solve this problem?

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.  But I guess it's too late for this for so long that there are probably no so old restore points.

  If the system restore does not work, do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not work, try to start in safe mode (repeatedly hit F8 key so that the start and go in safe mode with networking).  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator.

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well he comes complete with no corruption, it could not repair (if it has these post of corruption here or try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228.

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If this does not work, then please post repetitive errors in Event Viewer on the stop (Start / Control Panel / administrative tools / Event Viewer).  Here's how to use Event Viewer: http://www.bleepingcomputer.com/forums/topic40108.html.  From what I understand, there is none of the events (which surprises me because a freeze should certainly generate an error event).

  If this does not work, you will need to do a repair/system upgrade using the Windows Vista Installation disc authentic (you own or that you can borrow from someone).  Here is the procedure: http://www.vistax64.com/tutorials/88236-repair-install-vista.html as well as the upgrade from an earlier version of the Windows section of the following: http://support.microsoft.com/kb/918884.  Although this will not affect your data, settings or programs, you should always back up your data before you start just be on the safe side. If other procedures do not work, it is almost certain to work (but you NEED a disc).  You can have a lot of updates to re - install (including all you need to remove service packs).  If the version on system with SP1 or SP2 preinstalled cane and the disc is an earlier version, then you will need to do a slipstream drive as follows: http://www.vistax64.com/tutorials/151606-vista-sp1-slipstream-installation-dvd.html.

  I hope one of these procedures can solve your problem.  If this isn't the case, after return and we will try something else.  Return message anyway so we know how it turns out.

  Good luck!

  Lorien - a - MCSE/MCSA/network + / A +.

• Satellite A100-011 with Vista: DVD-ram UJ-850 s can not burn DVDs dual layer

  Hello

  cannot find answers to my problem, so start a new topic.
  Having Satellite A100-011 with Vista preinstalled and Mat * a DVD - RAM UJ-850 s (firmware 1.10).

  Recently installed Nero 7.5.9 and you want to burn DVD (6, 5 GB) media dual layer (Immation - Ritek).

  First time Nero stopped with information: could not perform start of Disc At Once (without damaging the media).
  After that, run Nero as Windows XP - SP2 program and burn half the disc (first layer), but when to start to burn the second layer (I guess), stop once again with the same error information (could not perform start of DAO).

  Simple disc burning layer without problem.

  Anyone any idea how to solve this problem?
  Thank you
  Luci

  Hello

  tried to record double-layer of a different brand? Maybe you should try it, because sometimes certain brands are not really taken in charge or not very well. And check the toshiba (or google) pilot site for new drivers or firmware for this drive, sometimes that it really helps.

  I think that the media are not really compatible, I ve read some similar problems in the roxio forum and they solved by using another brand.

  Would be nice if you give some information on this case... :)

  Welcome them

• I have a new desktop computer HP with Vista Home Premium 64-bit, with 8 GB RAM and when I try to start Zoo Tycoon 2, he won't play, said that I have no memory system.

  I have a new desktop computer HP with Vista Home Premium 64 - bit, with 8 GB of RAM, and when I try to run Zoo Tycoon 2, I get the following error message:

  You need at least 256 MB of system memory to run Zoo Tycoon 2. (0Mo detected)

  Y at - it a patch? I have read many "Workaround" and none of them work. I tried to run in Windows XP compatibility mode and it didn't work.

  Hey tprefling,
   
  Thanks for posting in the Microsoft answers site!
   
  Right-click on the zt.exe file and choose "Run as Administrator" to launch the program.
   
  See if you are able to play the game.

  If this does not work, turn your computer to clean the start State and see if the fgame plays very well.
  
  To put your computer in a clean boot, follow these steps:
   
  Note: If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.
   
  1. sign the computer by using an account with administrator rights.
   
  2. click on start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
   
  3. on the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)
   
  4. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all.
  Note: Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.
   
  5. click OK and then click on restart.
   
  For more information about the clean boot, see the link below:
  http://support.Microsoft.com/kb/929135
   
  In addition, change the size of virtual memory and see that helps. For more information, see:
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-the-size-of-virtual-memory

  For more details on the Zoo Tycon game, consult the following link:
  http://forums.zootycoon.com/forums/default.aspx
   
  I hope this helps!
  Gokul T - Microsoft Support

• I can't seem to install SP1 with Vista Home Basic and receive the error code 80073712.

  I can't install SP1 with Vista Home Basic.  I get an error code 80073712.  I tried to install the system update readiness tool and it tells me that my system does not apply to it.  I know that I must have a file corrupted or damaged somewhere but don't know where. I'm confused. Can someone help me?

  Moved from Vista to install, upgrade and activate Forum.

  Original title: installation of SP1

  I know that I must have a file corrupted or damaged somewhere but don't know where. I'm confused. Can someone help me?

  Donald,

  The computer belongs to you or your employer?

  (When was the last time you checked your system for malicious programs?)

  In addition to using an anti-virus, as Malware/spyware scan:

  http://www.Malwarebytes.org/products/malwarebytes_free>

  (MBAM) Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  In addition, scan with the free Version of (SAS)

  http://www.SUPERAntiSpyware.com/onlinescan.html>

  `~`

  Click Start type cmd (you should see the command prompt fill up) right click and select run as administrator.

  Inside the command prompt, type sfc/scannow

  * Information about the System File Checker

  http://support.Microsoft.com/kb/929833>

  Reset

  `~`

  Run the link Fix It, you will find on this http://support.microsoft.com/mats/system_maintenance_for_windows/en-us>>

  `~`

  If no malware has been detected, then please download and Save the tool update system (or CheckSUR).
  http://support.Microsoft.com/kb/947821>

  Be sure to download the version of the tool that fits the computer architecture. If you don't know what it is, then click on the link under

  http://support.Microsoft.com/kb/827218/en-us>

  When the download is complete, please read this before you run CheckSUR.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135>

  Once you have configured and rebooted the system to clean boot state, run CheckSUR (. Windows6 0-KB947821-v10-x 86.msu or)
  Windows6.0 - KB947821-v10 - x64.MSU) with the system connected to the internet. It will download and try to fix the incompatible component store.

  NOTE: Start-up mode minimum state all the 3rd party firewalls will be disabled.

  Open Control Panel > firewall Windows to check the native Vista Firewall now on.

  When CheckSUR finishes running, restart the computer.
  See if it can be updated now by opening Windows Update in Control Panel and clicking on the link to check for updates in the left frame.

  FYI

  If the tool (Checksur.exe) system update solves the problem, you will need repair Windows.

  `~`

  The time and date of this moment in British Colombia, Canada is 01:05

  Friday, February 14, 2014
  Pacific (PST) - 0800 UTC standard time

  UTC/GMT is 09:05 on Friday, February 14, 2014

  Current weather conditions in Vancouver

  Cloudy43 ° F / 6 ° C

• Acer Aspire laptop with Vista Home Basic Edition does not, System Restore does not, sfc, find corrupt files but do not repair. Need help!

  Hi, I have an Acer laptop Aspire with Vista Home Basic Edition that came pre-installed, so no records only the disk hard drive partition.

  I turned on my laptop today and it starts but the loading bar of stalls at the black screen with "(c) Microsoft Corporation" and dragging green. The slide bar will continue to drag, but nothing else happens which means that I understand even as much as the login screen. I rebooted and tried Windows recovery, but the only remedy to what he suggests is a restoration of the system, which does not have any point, I try to restore it.

  To remedy this, I have connected in safe mode and ran the SFC command prompt. It scans my system and told to find corrupted files, but he can't heal some. This is where my knowledge limit runs out. I don't know how to fix the files that the SFC cannot. (Also I created a journal using the findstr command prompt and checked but it say anywhere that it was unable to fix it so I'm not even sure how to identify corrupted files)

  As it's an Acer laptop, Aspire I'll try their eRecovery tool to return my computer to factory settings, but it won't work in safe mode, and as I said I can not connect normally. I tried alt and F10 at the initial boot screen when I turn on, it loads the windows files and shows the Acer "Please wait a moment" screen and then nothing happens again.

  I can't afford to get it fixed, and there is no chance I can get a new laptop. Any ideas/help? Thank you.

  Hello

  You have t in Normal Mode to resolve problems by using upgrade repair facility that is SFC

  Read this topic eRecovery Acer.

  http://Acer.custhelp.com/app/answers/detail/A_ID/2631

  To start the system recovery:

  1. Restart the computer.
  2. When the Acer logo appears on the screen, press the left Alt and F10 keys.
  3. If you are prompted with a Microsoft Windows splash screen, press the Enter key.
  4. After that the Acer eRecovery Management application is loaded, select your type of restore.
  5. Read the review and then click Next when you are ready.
  6. Click Next to start the restore process. It may take 10 minutes up to an hour fom anywhere to restore.
  7. Once the restore is complete, your computer will restart. After the reboot it will load Windows and start the installation of your software and drivers. Your computer will restart several times during this process. Once they are all completed, your computer will be like it was when you bought it first.

  See you soon.

• I have a Compaq with vista home basic 32-bit preinstalled and I want to upgrade to 64

  I have a Compaq with vista home basic 32-bit preinstalled and I want to move to 64-bit is it possible to use the sticker on the side of the case to just upgrade the same version of windows, but just for the 64 bit for windows vista home basic 32-bit new installation of vista home basic 64-bit will be the key oem on the sticker.

  Yes.  The product key on the sticker will work with both versions of the software.