Created in Esxi virtual MACHINE can't see the network

Similar Questions

• Virtual machines can ping throughout the network, but can't ping in them.

  More in detail, we run ESXi 5.1 on our host servers. We then run a client vSphere on one of our client machines that can reach the host by a Cisco 3750 switch servers. So it is, machine client, Cisco switch, then the host servers. The server host has 2 network cards going to the switch. NIC0 goes to a trunk port, and NIC1 goes to an access port. In vSphere, we have created a virtual switch that has two physical network interface cards activated. For our management network, the VMKernel port, VLAN ID All we (4095), then we have NIC0 as the active map. Then we have a "Server" network, the Virtual Machine port group, with VLAN ID 30 (our vlan internal) with NIC1 as the active map. Once we have this, we can ping from our virtual servers to our default gateway, then anywhere else in the network, but nothing can ping the virtual machines. We tried to watch a traceroute to the VM, but all it shows is, VM NIC, default gateway, and then destination... Ask for more information if you need.

  Thank you

  Tim.

  Hi and welcome to communities,

  What guest operating system are your current virtual machines to run? If it is windows server, it is a chance network discovery is simply disabled. This will diminish the ICMP packets and you may not their ping.

  If the port of 3750 for NIC1 is configured as VLAN ID 30 trunk.

  Your Portgroup is configured with VLAN ID 30.

  Inside the guest virtual machines you did not indicate any configuration of VLAN, right?

  Tim

• Clone a virtual machine and change is the network settings?

  I'm looking to clone a virtual machine several times change the network connection and the IP he uses, any help appreciated.

  NP, alternative, will host this script:

  $vmlist=Import-CSVC:vms.csv
  foreach($itemin$vmlist) {
   # I like to map out my variables
   $vmname=$item.vmname
   $ipaddr=$item.ipaddress
   $subnet=$item.subnet
   $gateway=$item.gateway
   $pdnswins=$item.pdnswins
   $sdnswins=$item.sdnswins
   #Get the current interface info
   $GuestInterface= Get-VMGuestNetworkInterface -VM $vmname -HostCredential $HostCred-GuestCredential$GuestCred
   #If the IP in the VM matches, then I don't need to update
   If ($ipaddr-ne$($GuestInterface.ip)) {
       Set-VMGuestNetworkInterface-VMGuestNetworkInterface$GuestInterface -HostCredential $HostCred -GuestCredential $GuestCred -IP $ipaddr -Netmask $subnet -Gateway $gateway -DNS $pdnswins,$sdnswins-WINS  $pdnswins,$sdnswins
   }
  }

• vSwitch ESXi 5.1 workaround to virtual machines (direct access to the network)

  Hello world!

  I have a server running properly the 5.1 ESXi hypervisor and got inside the physical grid active router with DHCP. How can I configure the vSwitch on ESXi 5.1 work not managed on the network, without VLAN and have direct access to the network?

  Just to clarify, I would like to first of all virtual machines VMware Workstation works - if it is possible to run several virtual machines and define all NICS (Network Interface Card) as connected by a bridge, that is to say. Each VM gets the specific configurations of IP to the external router.

  Since now, thank you very much for the help!

  Best regards

  Eduardo

  With ESXi the vSwitches work comparable to Bridged networking, so there is really nothing special to do.

  André

• Time Machine can't see the 2nd Logical Volume

  I have a RN104, there 4x3TB disks in there, configured in 2xRAID 1 volumes.

  The 2nd Volume has recently added so that I can activate and use Time Machine for backups of my Mac.

  That's the problem, when I start to set up Time Machine, it cannot see the remaining space in the 1st volume, I can't find a way to set up Time Machine to see or use the available space of the volume, I have installed specifically for Time Machine backups.

  All the thoughts/views/answers?

  Kind regards

  Glenn.

  Hello Thresherinc,

  The /data/home/USER/.timemachine is where Time Machine stores data, this folder is always the default value / 1 volume of the NAS and can never be moved.

  Kind regards

• When a right click to create a new folder, I can't see the new option 'file' in the menu. Why?

  I'm running Win 7 Ultimate and it happened on my system for the first time: when a right click to create a new folder, I can not see new option 'file' in the menu.
  I remember that I did not create new records from the last 5 days, so I can't say when the problem came. But I remember that yesterday I uninstalled 'free. '
  antivirus application which disappointed me a little. And it was the only action I suspect to have effect on my system.
  So I can't create folders in the usual way. And I need help to solve the problem. Moreover, the cmd command line works and when I type:
  MD x:\AA,
  The result is a folder named AA at the root of drive x:

  Again, I ask for help.
  Thank you
  Chris

  Hello

  Go to the following site.

  File Association fixes for Windows 7 - the Winhelponline Blog:
  http://www.Winhelponline.com/blog/file-Asso-fixes-for-Windows-7/

  In the blue box, click on the item in folder and download the file to your desktop.

  Unzip the file.

  Double-click the folder_fix_w7.reg file to add the information in the registry.

  In the meantime, you can also use the keyboard shortcut to create a new folder.

  Just press Ctrl + Shift + N.

  Concerning

• Can't see the network hpsetup on my Macbook Pro on a C4780

  Help - I'm trying to get working wirelessly on a C4780 connected to a new Macbook Pro with 10.6.2.  I am on a network of wireless-G linksys with WPA_PSK and when the HP configuration utility try to connect to my network, it goes into "the network... search. "forever.  So, I tried to connect manually by some of the other posts, but I can't find the network hpsetup even after resetting to the default printer.  The serial number of the printer is CN99SD12ZF.  Is that printers with factory default SSID settings incorrect?  If so, what I try next?

  Some sent C47xx factory printers have an incorrect default setting in their non-volatile memory that prevents the method of ad-hoc configuration.  There is nothing wrong with the printer HW or FW and you should still be able to set up the printer using the Setup program on the CD.

  If necessary, it is a manual method to get the printer on your network.  Here's how to printers wireless C47xx:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  • Press the Scan button to get the wireless settings
  • Select wireless Menu
  • Select wireless settings
  • Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks and then Showall the bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  In the Web page of the printer, click Networking , and then select Wireless (802.11().  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network

  I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you

  Firewalls are disabled on remote computers?

• Can't see the network after 6.5.5 to 8.0 upgrade

  I have a couple of virtual machines that are running at the same time and talk to each other as well as with the host operating system.

  Since the upgrade to 8.0 I can no longer ping or join other machines or the host operating system.  I have not changed the settings since the upgrade.  Two virtual computers have IP addresses static of 192.168.0.123 and 124 respectively.   The gateway is 192.168.0.100.   No machine can ping each other, or the front door.

  Has anyone else seen elsewhere?   I'm completely dead in the water.

  See you soon

  Automatic bypass is not working properly, so select a specific host for VMnet0 NIC in the virtual network Editor.

• Can't see the network PC MAC computer, unless I have use RUN in the start menu and type in the IP address.

  Original title: MAC to PC NETWORKING.

  I added my Mac to my PC network workgroup.  I can see the PC from my Mac, but not my Mac to the PC network puts unless I have use RUN in the start menu and type in the IP address. I am running XP Pro SP3.

  Hi markymo777,

  I suggest you to check if you can see the MAC computer with the UNC path - \\computername\sharename. Later, check to see if the problem persists.

  Hope the helps of information.
  Please post back and we do know.

• Can't see the networks without wire in Dell Inspiron

  I have just moved house (previously in the United Kingdom, in Australia) and now I can't get my Dell Inspiron 1525 to find (Vista 31 bits operating system) wireless networks. Under network and sharing Center, if I click on connect to a network or setting up a connection or network, nothing happens. Similarly, under Manage Wireless Networks if I select add nothing happens. However, if I select the Dell Wireless WLAN Card Utility I see my network wireless on the Site tab. Also, I can see and connect to the network wirelessly to other devices (for example the iTouch).

  Hi dellUser_742

  Please refer to the below links and check if the steps to help you resolve the issue.

  http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows?T1=tab02

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  I hope this helps.

• New virtual machine retains boot from the network (not available)

  Dear community:

  I'm trying to boot and install from an image ISO of Windows 95 file that I created from the original CD.  VM Ware Workstation 7 continues to try to boot from the network even if I have the boot order in the BIOS configured to boot from the CD - that didn't work.  And if it is set to boot from an iso file it will automatically launch that file instead of looking for a MAC address in an infinite loop on the network.  How can I solve this problem with my boot?

  Sincerely,

  Markerline

  the CD should appear as D:

  so type D: to the prompt - then it has to go to D:

  type dir to find the Setup program

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• Re-installed Windows XP and now I can't see the network connections and cannot get online.

  Our pc is down a few days ago, so we reinstalled xp.  The xp upgrade.  Now, we show no internet connection and can not get on the net.  Our Device Manager indicates a problem with the drivers being not downloaded on the network adapters.  Also the modem is not recognized when I try to connect. I tried to download the fix for me on microsoft for a flash player and it did not work.  Can you please help me reinstall it?  Thank you

  original title: reinstalling Windows XP

  Go to your computer manufacturer's support web site and search for the Windows XP drivers for your specific model number.

  If there are Windows XP drivers, then download to a folder on your hard drive and install them all, starting with the card mother/chipset drivers, LAN, Audio, USB, SATA, etc, and so on.

  List of computer manufacturer support sites:
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  If you have an Intel motherboard, you can try the Intel driver update utility: http://www.intel.com/support/detect.htm?iid=dc_iduu

  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems
  Vista: http://windows.microsoft.com/en-US/windows-vista/Tips-for-fixing-common-driver-problems

  Graphics/video drivers:
  Check the download site of the manufacture of the graphics card for the newer Windows XP drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  J W Stuart: http://www.pagestart.com

• Can't see the network of cult film - game is saved.

  When I select 'The Cult Movie Network' and try to stream to my Bravia-3 from TV, I get "Please visit Web of Sony Essentials to associate your device with our service."

  My TV has been recorded for a long time and does not display ' Registration Code: device is registered.

  Catch-22.

  Help!

  Hello Dave,

  Welcome to the community of Sony.

  Please contact Sony support directly for further on troubleshooting this type of problem.

  http://eSupport.Sony.com/us/p/select-System.pl?Director=contact

  Kind regards

  Charlie

• VMKernel can not see the network...

  I have 4 NICs, 2 NICs service a vswitch with a service console and VMkernel a.   The service IP console works fine but I have no network connectivity for the VMkernel on the same vswitch with a static IP address.  If I set the VMkernel for DHCP, it gets an address of 169.x.  esxcfg-switch - l & esxcfg-NICS - l show no problem.

  Hello

  It seems the two network adapters that you use with that one VLAN configured on the pSwitch.

  • Try to configure vSwitch with a single NETWORK card, which saw Service Console PortGroup and confirm the S.C having connectivity

  • UN-Link the NIC of the vSwitch and add the second NETWORK card and confirm the S.C with connectivity.

  If you have a connectivity on both network adapters, and then in the pSwitch problem seems to be.

  • Troubleshooting above with VMKernel PortGroup and confirm - there is connectivity to the other host via the vmkping command.

  • If doesn't work then be sure to there is a circuit in the pSwitch or not.

  • If you have chutes, make sure the tag pSwitch Port.

  • Put the VLAN ID in the VMKernel PortGroup.

  • Put the VLAN ID in the Service Console PortGroup

  If you are not sure, connect two VMKernel network cards to a crossover cable and try the connectivity tests.

  Best regards

  Hussain Al Sayed

  If you find this information useful, please give points to "correct" or "useful".