cRIO is unable to enter active mode, because of the ethercat slave

I have a (CS27 of HBM) ethercat slave connected to a cRIO 9068. If I right click on the device HBM under the EthercatMaster and go to 'Device status online' I put first the State of the HBM "Operational Pre", "Operational security" and then "operational." The CX27 indicates the operational stae with a LED.

But when I try to put the cRIO in "active" Mode I get the error message:

-The analytical engine NOR could not be changed to active mode, because one or several devices to find could not access the operational mode.

The problem is finally solved.

The problem has been layout of different synchronization between the HBM and cRIO (801 vs 802) Manager.

Thanks to HBM to provide a firmware update to take in charge the provision used by OR!

Tags: NI Hardware

Similar Questions

  • EtherCAT - OR Scan Engine could not be changed in Active mode, because one or several slave devices does not have operational status

    Hello, I use a Compact Rio 9074 with an EtherCAT NI 9144 chassis extension

    I am able to see both devices 9074 and 9144 Labview project, but when I try to deploy configuration 9074 controller tracking error is displayed:

    I tried deployment while defining the Configuration Mode and Active Mode. Also, when I check on the status of master Ethercat online its State in: pre-operational with errors. And appers this message: error-2147137769 occurred at an unidentified place

    I'm using Labview 2011 and the OR cRio has installed:

    I tried formatting cRio and reinstall NI Ethercat and scanner again

    I wonder if anyone has the same problem, I'd appreciate any help.

    Thanks in advance

    Thank you very much, DirkW worked for me immediately

  • Dreamweaver problem: what is active mode live view the program block

    [English]

    Dreamweaver problem: where is the block active mode live view. I have to wait at least 3 minutes to restore the program, and try again to work. This only happen in a way live view. Please help with this problem is very annoying

    [Spanish]

    Dreamweaver problema: cuando hangs from activa Live discovered. Tengo por lo menos 3 minutos e restore el programa para wait brought Nuevo a trabajar. Esto sucede en solo a modo to display live. Please help con este problema're muy molesto

    Hi Angello,

    Which version of Dreamweaver, you are on?

    Thank you

    Preran

  • Unable to access Adobe Flash because of the MSDCVP100.dll

    I GET THE ABOVE STATEMENT, WHEN I START COMPUTER. I WATCH ADOBIE FLASH HAS BEEN DOWNLOADED, HOWEVER, I AM UNABLE TO ACCESS THE FILE.

    It's not the err msg

    What is it exactly?

  • Unable to install photoshop cs6 because of the beta?

    Hello!

    I tried to install photoshop cs 6 with my creative cload account, but it says that there is a beta version of photoshop on my pc.

    I looked and uninstalled all the programs on my computer and finally deleted Adobe but I still get the same message

    a beta version of photoshop... With this problem, I can not install photoshop cs6...

    So what can do more, I do now?

    Welcome them

    Adobe forums: FAQ: how to uninstall the beta version of Photoshop CS6?

    Mylenium

  • cRIO-9074 2147138533 error on active state transition analysis engine

    I have a cRIO 9074 configured as master EtherCAT.  The code for the RIO FPGA is followed by other data on the State and he is able to shut down all power to the rest of the system (including the EtherCAT slaves) for safety.  If I power cycle the cRIO (whose power to EtherCAT slaves Travel) I get the following error when it goes into active mode on the scan engine:

    Error 2147138533 has occurred to the property node (arg 1) in the updated scan engine Mode.vi-> RT Startup.vi system

    Possible reasons:

    The telegram is to expire.

    Check that the master device is connected to the EtherCAT network. Ensure that each slave in the EtherCAT network device is turned on and properly connected.

    Is it possible to start the engine even with the slaves turned off?  I just need to change my program to dynamically discover the slaves to stop the scan engine of faults on scan engine transitions?  I don't want to feed my slaves EtherCAT back on until I can read data that are currently being monitored by the scanning engine on the RIO even... is this possible somehow?

    Hello

    EtherCAT is tightly coupled with the analytical engine.  There is no way to set the active scan engine, while an EtherCAT Slave is disconnected.

    I recommend watching the following Article of knowledge-based programmatically discover and access EtherCAT.

    http://digital.NI.com/public.nsf/allkb/FDC87938F1191A3C862578FF00757270

    Kind regards

  • Impossible to download Acrobat Pro because of the 'restrictive access privilege' on Mac

    I am unable to download Acrobat Pro because of the 'restrictive access privilege' on a Mac Mavericks folder ('Applications', where else?), but I left "Read & Write". I won't install anywhere else, so need help. Thank you.

    Mickey McFly please make sure you download your download folder or a different folder in addition to your Applications folder.  Once Adobe Acrobat is downloaded you can install the software in your Applications folder.

  • Text of the Web site is not displayed. Could not open in safe mode because I can't see the text.

    All web pages show only the images no text. The display is normal in Chrome. I'm unable to open in safe mode, because the drop down menus have no text. I prefer not to remove and reload firefox as I don't want to lose the bookmarks and saved passwords. Some would like to help. Thank you.

    Open in safe mode and went very well. Graphics Accelerator box unchecked and back to normal. Thank you very much for the excellent help.
    Chris

  • I rebooted my machine yesterday and now when it comes to the screen with the scroll bar it restarts in loop. Impossible to enter Safe Mode (arrives at crcdisk.sys and while it recharges) or normal startup mode.

    I restarted my machine yesterday and now when it comes to the screen with scrolling bar (think Night Rider), it restarts in loop.  Impossible to enter Safe Mode (arrives at crcdisk.sys and while it recharges) or normal startup mode.  Startup Repair is unable to repair.  She argues that the onus of a BadPatch.

    Startup Repair shows the following:

    Problem event name: StartupRepairV2
    Signature of the problem 01: external Media
    Signature of the problem 02: 6.0.6000.16386.6.0.6001.18000
    03:6 problem signature
    Signature of the 04:262148 problem
    Signature of the problem 05: BadPatch
    Signature of the 06 problem: BadPatch
    Signature of the problem 07:0
    Signature of issue 08: 1
    Signature of the problem 09: SystemRestore
    Signature of the problem 10:0
    OS version: 6.0.6000.2.0.0.256.1
    Locale ID: 1033

    Hello

    I hope you made redundant data backups as I suspect that the drive has failed. If a PC, you must
    remove all power and remove and reinstall all the cables (at both ends where possible), memory and cards. Do
    not tighten, effectively remove and replace them with care.

    Click here for the manufacturer of your hard drive and launch their diagnosis on your drive.

    By manufacturer diagnostic utilities
    http://www.techsupportforum.com/hardware-support/hard-drive-support/302602-hard-drive-diagnostic-utilities.html
    SpeedFan
    http://www.almico.com/sfdownload.php

    HD Tune
    http://www.hdtune.com/

    ----------------------------------------------

    If necessary:

    You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
    saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

    You can use another DVD that are not protected but you will need to copy you have the product key.

    On-site upgrade
    http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

    If nothing works, you can make a repair facility that must save the data but you will need to
    Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
    need to know your product Code.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    How to perform a repair for Vista Installation
    http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

    No new chances.
    Rob - bicycle - Mark Twain said it is good.

  • Classic mode by using the Alt + Tab - needs to get the active window

    I'm running Win7 Ultimate mode classic (the aero mode was just too much visual noise) and for years, I used the Alt + Tab to switch between applications. Starting with Vista, the content of the Alt + Tab pop-up window sorts and does not retain the positions she had in XP. Y at - it all the settings that I can change to get the unsorted window XP. With sorting darn, I'm looking for 'the' the window, I want to bring to the fore. I almost always several applications running (10-20) and several windows in each application, so it is not uncommon that I'll have 30-50 windows open when I'm researching a topic and try to create a document or a presentation on the topic.

    Hey jgt,
     
     
    Here is a workaround to get the classic Alt + Tab bar.
     
    1. open the Explorer Windows & a few applications so that you can start using Alt + Tab feature.
    2. press Alt + Tab keys to display the keys Alt + Tab bar.
    3. without releasing the keys, press another Alt key once and release the second ALT.

    Note: Do not release Alt + Tab again.
     
    4. now, press the Tab key to see the classic Alt + Tab bar.
     
    Note: You will need to repeat this procedure each time you want the feature back.
    If you are comfortable with the registry, you can disable the Aero Alt Tab permanently.

    If you are comfortable with the registry, you can disable the Aero Alt Tab permanently.

    Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.

    Back up the registry
    http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

    To get the classic Alt Tab functionality in Windows 7 the Registry Editor:

    1. go to start, type regedit and press ENTER.
    2. go to the location following HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer
    3. in the right pane, create a new DWORD AltTabSettings and set its value to 1.
    4. now, whenever you you press the keys "Alt + Tab" together, he'll show Windows XP style classic screen Switcher "Alt + Tab" rather than the new screen.
    5. to restore the default active Aero Switcher "Alt + Tab" screen, simply delete the DWORD AltTabSettings, created in step 3. Log out and sign in again to take effect.

    Hope that solves your problem.

    Kind regards

    Shinmila H - Microsoft Support

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Windows 7 activation failed because no system on the SSD before installation.

    Hi, I just updated my computer and I have installed the version of win7 upgrade.

    I got the error activation failed because there was no system on the SSD before installation.
    Instead of having to do all that again (install xp and win7 or reinstall win7 then win7) I did a registry change
    HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Setup\OOBE has changed the 1 to a 0 and restarted
    Entered the CD - Key and got the error
    [code]
    On a computer running Microsoft Windows non-core, run "slui.exe 0x2a 0xC004F061" to display the error text.
    Error: 0xC004F061
    [/ code]
    activate Windows then told me, "the product key you entered cannot be used to activate windows on this computer".
    Then I tried the thing about the phone call.
    has chosen country as the Iceland's nearest.
    received 2 numbers
    800-8236, I get the message that this number is not in use.
    + 47 23 162 126 there I have the language Norwegian (or something) answering machine
    What can I do?

    http://Windows.Microsoft.com/en-us/Windows7/Windows-7-activation-error-0xC004F061

    However, the requirements for the media upgrade is that you have an operating system already eligible such as Windows XP or Vista installed to use it. Since the Windows 7 end user license agreement.

    15 UPDATES. To use upgrade software, you must first be licensed for the software that is eligible for the upgrade. After the upgrade, this agreement takes the place of the agreement for the software that you upgraded. After upgrade, you can no longer use the software that you upgraded.

    So, if you are always denied, you will just have to reinstall Windows XP or Vista and let it do the verification of eligibility.

  • Startup Repair has worked 9 hours from WAU to go home 7-7 pro running. System is not blocked because I have control of the mouse and HD shows activity. What is the problem?

    Startup Repair has worked 9 hours from WAU to go home 7-7 pro running. System is not blocked because I have control of the mouse and HD shows activity. What is the problem?

    I would be out of system repair and safe boot mode:

    Start your PC, just before the system loads the Windows operating system; Press the [F8] key function 8 on your keyboard which will launch the menu Advanced Boot Options. Select Safe Mode.

    Click Start
    Type: CMD, according to the results, right-click CMD
    Click on "Run as Administrator"
    At the command prompt, type: sfc/scannow

    This will check for any breach of integrity

    Restart your system

  • I'm unable to use windows applications in my college. Is it because of the proxy connection?

    I'm unable to use windows applications in my college. Is it because of the proxy connection? Each app says I'm not connected to a network. Please let me know how to encounter this problem.

    Hey Brad,

    1. What is the accurate and complete error message you get?
    2. don't you make changes to the computer before this problem?

    There could be various reasons why you will not be able to connect to the Windows store.

    I suggest to disable the proxy server and check.

    (a) press the Windows key and the R key to open the prompt to run . Type inetcpl.cpl in the run prompt and press to enter.
    (b) in the 'Internet Options' window that opens, click on the tab "connections" at the top.
    (c) click on 'network settings' at the bottom of the section "connections."
    (d) if the "Proxy Server" box is marked with a check, click it to uncheck/disable.
    (e) click on 'Ok' to close the window "local area network (LAN) settings".
    (f) click on 'Ok' to close the 'Internet Options'.

    I also recommend a complete analysis using the antivirus program installed on the computer or by using the Security Scanner from Microsoft that this problem can also occur by malware.
    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Safety Scanner WARNING: There could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

    Hope this information helps. If you have any questions, please let us know.

  • Can not enter serial number because it is alphanumeric.

    My Windows 8.1 computer died so I was forced to buy a Windows 10.  I managed to install the Photoshop 5.5 I bought.  It works perfectly as a trial, but I'm unable to enter the serial number because it is alphanumeric.  It's a number of drama that I paid for. How to operate?  There is no phone support and no help in support.

    There is the problem. Your CD has Photoshop 5.5 is so old, so it is no longer available-download and everything you have installed is not your old 5.5

    Uninstall what you have installed and use your CD. Need you your serial number.

  • Maintenance mode, unable to connect: 514 error connection to the instance of service pass vmds

    Hi all

    I do a few patches manually on ESX 4.0 host.  I forgot to get into maintenance mode, tried to patch and had an error on entering maintenance mode.  So I tried to get into the mode of maintenance with the following command:

    vimsh - n hostsvc/e/maintenance_mode_enter

    I get these messages:

    Current working directory: / root

    vmaCore: initSSL: make versionCheck = true

    handshake Timeout = 20000000

    Unable to connect: 514 error to connect to the instance of the service host-vmds

    Not connected

    Not connected

    Someone has ideas of what happens and how to solve?

    Thank you.

    Take a look at reboot on an ESX or ESXi Server management agents and VMware: hanging out on an ESX Server maintenance mode (9639912)

Maybe you are looking for