CUCM 7.1 (3) TFTP Auth Fail

Since the upgrade of CUCM 7.1.3.10000 - 11 all new phone plugged into the system gets an 'auth fail"from the TFTP server when you try to upgrade the firmware to the version that comes with 7.1 (3). Phones that were saved before the upgrade work fine. I see the same behanviour on our non-production environment, which is also in 7.1.3 - 10000-11.

Firmware of the phone for a 7.1 (3) on the plateau of 7961G is SCCP41.8 - 5-2SR1S

Someone at - sle seen this behavior before... did someone else turns 7.1 (3) yet?

Hello world

My problem was that the Firmware of the phone must first be 8.5.2 and after that, the phone can go to 8.5.3. What is written in the Relase Notes

http://www.Cisco.com/en/us/docs/voice_ip_comm/cuipph/firmware/8_5_3/English/release/notes/7900_853.html

Concerning

Tags: Cisco Support

Similar Questions

  • dot1x auth-fail vlanX does not

    Hello

    I have configured 802. 1 x on a fas0/3 and works very well.

    I'm testing to set up a restricted VLAN on that port, and it does not work.

    This is the configuration:

    interface FastEthernet0/3
    switchport access vlan 11
    switchport mode access
    dot1x EAP authenticator
    self control-port dot1x
    LAN virtual auth failure of dot1x 30
    dot1x max-authentication failure 2 attempts

    When the PC connected to the Fas0/3 authentication failed twice, he should go to 30 of VLAN, but this isn't the case (port fas0/3 remains 11 VLAN in down state)

    VLANS SHOW:

    11 active VLAN0011 Fa0/2, Fa0/3, Fa0/4
    30 active LIMITED

    SW1 #sh dot1x interface FAS 0/3
    Dot1x FastEthernet0/3 information
    -----------------------------------
    EAP AUTHENTICATOR =
    PortControl = AUTO
    ControlDirection = both
    HostMode = SINGLE_HOST
    A re-authentication = off
    QuietPeriod = 60
    ServerTimeout = 30
    SuppTimeout = 30
    ReAuthPeriod = 3600 (configured locally)
    ReAuthMax = 2
    MaxReq = 2
    TxPeriod = 30
    RateLimitPeriod = 0
    AUTH-Fail-Vlan = 30
    Fail-Max-des authentication attempts = 2

    It is a 2960 running c2960-lanbase - mz.122 - 35.SE5, what Miss me?

    Federico.

    Ferderico,

    How do you test the VLAN Auth failure?  If you test with a bad password and using the PEAP Protocol it is considerred a reproducible error which should not cause a rejection of the RADIUS server, instead the password can be retried without ripping first in the tunnel TLS via an Access-Reject.  As long as it is configured, it should be 3 access - reject the server RADIUS must be filed in the VLAN auth failure.  If I remember correctly a bad username is also reproducible.

    If you use DCC 5 you can lower the number of retries PEAP 1 in which case you will have failed connection 6 times with a wrong password to hit the VLAN auth failure.

    -Jesse

  • DHCP client when the auth-fail dot1x vlan not asking not

    Switching VLAN works very well when the user is authenticated. The machine is on vlan X, the user connects, port goes to vlan and then receives an ip address of the vlan Y. When the user disconnects, machine reauths and dates back to the vlan X.

    However, when I use the LAN virtual auth failure of dot1x on the port, the switch will change to vlan Z, but the computer (XP) still has an ip address of the vlan x XP still shows as "trying to authenticate" which I suppose may be the problem with her not asking not DHCP (normally it only until after auth).

    Is there an authentication timeout setting somewhere in XP? Or y at - it another way this problem? It's XP with SP3.

    Is there not another way around the issue. The 'problem' is that the machine already has an IP address.

    Basically, Auth-Fail-VLAN works as if a network connected to a switch, watched x-number of chess administrator happening consecutively, and the admin allows the port anyway in mode authorized strength and hard-sets it in one VLAN specific. At this point, it's the supplicant on how / if she needs to get on the network.

    IOW, it's a bit as if you just change the VLAN on a port on the fly for any other reason... same question.

    One workaround might be of course ensure it fails at time of initial plugin, when machine requests an IP address at first (assuming only for Windows platform anyway).

    Hope this helps,

  • Dot1x comments Vlan / Auth Fail Vlan editions

    Hi all

    Configure dot1x on our access layer switch ports and I have a few problems with devices that fail authentication.  This is the current configuration on the way to the switch:

    switchport mode access

    switchport voice vlan 38

    dot1x mac-auth-bypass

    dot1x EAP authenticator

    self control-port dot1x

    multi-domain host-mode dot1x

    dot1x timeout server-timeout 10

    Server of reauth-dot1x timeout period

    dot1x tx-time 10

    dot1x timeout supp-timeout 3

    dot1x max - req 3

    dot1x max-reauth-req 3

    dot1x re-authentication

    criticism of dot1x

    critical recovery dot1x action reset

    dot1x auth failure vlan 7

    dot1x comments - vlan 7

    dot1x critical vlan 36

    spanning tree portfast

    spanning tree enable bpduguard

    When a non-employee connects they go through the authentication process and eventually fail dot1x and mab and placed in the vlan designated guest 7.  If you're doing a "show int gx / x status" on this port, switch-it shows the connected and to this vlan 7.  If you're doing a "show dot1x int gx / x details" it also shows the port as authorized (by Guest-Vlan) and politics of vlan is 7.  The problem is the user never gets a valid ip address - they receive only a 169.x.x.x.  Anyone has experience with this type of question or have any recommendations?

    Thank you

    Brian

    -First of all Eteinte, your switch orders tell me you are using old software on your switch, you must pass it first of all, there was a lot of correction of a bug and improvements to dot1x/mab in recent versions

    -Your problem is probably that the client dhcp of your comments is delay until you are finished with dot1x and mab, susally tx-period to a lower number of adjustment could help the time it takes before joining the vlan comments, but could also have an impact on your computers running dot1x, you should try some different values. Also, using Windows XP SP3 or Windows 7, also helps on your machines to dot1x, and finally using supplicant AnyConnect NAM he will operate properly without having any problems when setting the timers dot1x on your switch.

    -With the new software I go with default timers, perhaps change tx-5 second period and then use the "order mab dot1x authentication" and "authentication priority mab dot1x", also having your vlan comments like your vlan by default, will be generally also solve the problem of the guests have to do a new once-popular dhcp reqeust, however you can run into problems with stuff you wan't to use mab on.

  • VWIC3-1MFT-T1/E1, showing no recorded in CUCM 10.5

    Hello

    I am trying to record E1 and FXO 8 with CUCM 10.5 using mgcp. FXOs are recorded in CUCM but not E1, it shows not registered. I have attached the configuration of the gateway and the CUCM screenshot. I use the software REL C2900, Cisco IOS Software (C2900-UNIVERSALK9-M), T3 Version 15.4 (1)
    EASY SOFTWARE. Please let me if there is no error in my configuration.

    AD_Voice_GW #show ccm-Manager
    MGCP domain name: AD_Voice_GW
    Host of priority status
    ============================================================
    Registered primary 10.20.13.9
    First backup ready 10.20.13.8
    Second backup none

    Current active call manager: 10.20.13.9
    Backhaul/redundant link port: 2428
    Failover interval: 30 seconds
    KeepAlive interval: 15 seconds
    Last keepalive sent: 14:39:48 GMT April 10, 2015 (duration: 00:00:12)
    )
    MGCP traffic last time: 14:39:48 GMT April 10, 2015 (duration: 00:00:12)
    )
    Last failover time: None
    Last hour switchback: None
    Switchback lifestyle: graceful
    MGCP rescue mode: unchecked
    Start time of last backup MGCP: None
    Last backup MGCP end time: None
    MGCP download ringtones: disabled
    TFTP retry count to close Ports: 2

    Backhaul link info:
    The link protocol: TCP
    Remote Port number: 2428
    Remote IP address: 10.20.13.9
    Current link status: OPEN
    Statistics:
    Recvd packages: 1
    Recv failures: 0
    Xmitted of packets: 2
    Xmit failures: 0
    PRI ports in return:
    Slot 0, VIC 0, port 0
    Automatic download of configuration information
    =======================================
    The current version id: 1428657466-23cb555c-fb36-457e-81fa-58438df308d4
    Last downloaded-config: 00:00:00
    Current situation: waiting for orders
    Configuration of download statistics:
    Download tried: 1
    Successful upload: 1
    Download failed: 0
    TFTP download failed: 0
    Configuration has attempted: 1
    Successful configuration: 1
    Setup Failed (Parsing): 0
    Configuration (config) Failed: 0
    Last command upload config: new registration
    FAX mode: disable
    History of configuration error:
    AD_Voice_GW #.

    ==============================================================================

    D_Voice_GW #show ISDN status
    Global ISDN Switchtype = primary-net5

    %Q.931 is back at CCM MANAGER 0 x 0003 lis 0. Out of layer 3 can not appl
    There

    ISDN Serial0/0/0: interface 15
    DSL 0, the interface ISDN Switchtype = primary-net5
    L2 Protocol = 0x0000 L3 = MANAGER of CCM protocols Q.921 0 x 0003
    Layer 1 status:
    SHUTDOWN
    Status of layer 2:
    TEI = 0, CES = 1, SAPI = 0, status = TEI_ASSIGNED
    Status of layer 3:
    0 active Layer 3 call (s)
    CCBs active dsl 0 = 0
    The free channel mask: 0x00000000
    Number of L2 ignores = 0, ID of Session L2 = 0
    Total allocated ISDN TSC = 0
    AD_Voice_GW #.

    =====================================================================================

    AD_Voice_GW #show mgcp endpoint

    E1 0/0/0 interface

    GIS-TYPE V-PORT ADMIN ENDPOINT NAME
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_G: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place
      [email protected]/ * / 0/0/0 _Voice_: 15 place

    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW
    [email protected]/ * / _Voice_GW

    AD_Voice_GW #.

    Since ISDN layer 1 was showing as Deactivated/Shutdown, crc4 framing so could cause.

    regds,

    Aman

  • The copy from the tftp server to Flash

    I have the controls down to the copy from a tftp server to Flash, but cannot connect to the server tftp through the console.

    I need to set an IP address on an interface vlan, assign a port to the vlan and then plug my computer/server tftp running into the port?

    What is the best practice to access a router/switch tftp server?

    1 you must have a physical port with an ip address or interface vlan by ip address and the port assigned to this interface on your router/switch

    2 your pc needs to have an address ip in the same range make sure you can ping between the pc interface and router first then connectivity is there for the tftp to work

    3. make sure that no local firewall is running on your pc, sometimes this can cause the tftp to fail because it can be blocked according to what is running

    4. make sure that there is enough memory your camera flash to take the new image, your tftp server is running on your pc and the root folder is set int ready to load on the router/switch with your IOS tftp server

    http://www.Cisco.com/c/en/us/support/docs/routers/2500-series-routers/15...

  • 802. 1 x authentication fail - packages keep discarded

    Hi all

    I implement 802. 1 x using Catalyst 3560 and MS IAS as a radius server. The plan is, each PC must authenticate using PEAP with RADIUS and assigned to a VLAN. Fail authentication will be assigned to comments VLAN.

    The problem is when I test a PC, set the PC withouth 802. 1 x enabled, plug it into the port of 3560, maintains the port that PC packets rejected forever. I remove dot1x configuration on the interface, but he keep throwing all packages (can not ping anywhere). When I connected the PC to the other port with the same configuration (not dot1x), it works. I tried closed and no closure of the interface, disable - enable devices, remove config and etc but the PC can't ping anywhere.

    I'm glad paste the config. Could someone please explain to me why it happens and what is the solution? Thank you very much.

    Here is an example config which should work:

    interface GigabitEthernet1/0/5

    switchport access vlan 31

    switchport mode access

    dot1x EAP authenticator

    self control-port dot1x

    dot1x comments - vlan 35

    LAN virtual auth failure of dot1x 35

    end

    This should NOT prevent a non-1 x machine to access the network forever. With the foregoing and time by default, it is a waiting period of 90 s of 802. 1 X. You can change the time of the tx and the maz-reauth-req variable to achieve up to 2 sec, if you wish. If you remove 802. 1 X, then that should also not packages. If the above 2 items are produced, then you hit a software bug, and a case of TACS must be opened immediately. Are you sure that something like just DHCP has not expired on you well?

    NOTE: The above configuration has vlan 35 for the comments - vlan being equal to the auth-fail-vlan based on you indicating the need of this above. It might be different from that of the vlan-comments, if you want it to be. Some could be the same vlan as what is configured statically on both port [31].

    Hope this helps,

  • auth failure VLAN vs the VLAN

    Hi all

    What are the criteria for determining whether to use the local network VIRTUAL auth failure or the guest VLAN?

    What happens if a non - 802.1 x client connects to the port, tell a seller... 802. 1 x does not occur, then is he then comments crossing vlan?

    What happens if a salesperson brings a 802. 1 x PC capable and connects it... the identification fails, but I want the seller to go in the VLAN comments in any case, I could give them a temporary user name / maybe PW to authenticate with? Hmmm...

    Thanks in advance.

    Hello

    The local network VIRTUAL Auth-Fail is called if an Access-Reject is received from the Radius Server to the

    authentication of the user or machine.  The local network VIRTUAL Auth-Fail will be called after a certain number of failures

    not after the first failure of authentication.  It is a configurable value.

    The VLAN comments is called otherwise EAPoL traffic comes from the customer who connects.

    You can set the VLAN Auth failure and the VLAN comments on the same VLAN ID if you want to

    users who have disabled begging him or a person with invalid credentials (or no credentials).

    -Jesse

  • OdiSftpPut failed

    Hello

    I'm trying to transfer files to a remote server by using OdiSftpPut. However, I get an authentication failure. I provided the following parameters of the procedure.

    OdiSftpPut-HOST = 10.232.9.123:1000 - USER = Societeabc-password = password-LOCAL_DIR = / target/Societeabc - LOCAL_FILE = *. DAT-REMOTE_DIR = / target/file - COMPRESSION = NO

    I would appreciate any idea on how to solve this problem. Here are the details of the error, log

    org.apache.commons.vfs2.FileSystemException: could not connect to SFTP server "s ". ftp:// ' 10.232.9.123:1000/ '.

    at org.apache.commons.vfs2.provider.sftp.SftpFileProvider.doCreateFileSystem(SftpFileProvider.java:107)

    at org.apache.commons.vfs2.provider.AbstractOriginatingFileProvider.getFileSystem(AbstractOriginatingFileProvider.java:103)

    at org.apache.commons.vfs2.provider.AbstractOriginatingFileProvider.findFile(AbstractOriginatingFileProvider.java:81)

    at org.apache.commons.vfs2.provider.AbstractOriginatingFileProvider.findFile(AbstractOriginatingFileProvider.java:65)

    at org.apache.commons.vfs2.impl.DefaultFileSystemManager.resolveFile(DefaultFileSystemManager.java:693)

    at org.apache.commons.vfs2.impl.DefaultFileSystemManager.resolveFile(DefaultFileSystemManager.java:621)

    at com.sunopsis.dwg.tools.filecopy.RemoteFileCopy.copy(RemoteFileCopy.java:424)

    at com.sunopsis.dwg.tools.SftpPut.actionExecute(SftpPut.java:49)

    at com.sunopsis.dwg.function.SnpsFunctionBase.execute(SnpsFunctionBase.java:276)

    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.execIntegratedFunction(SnpSessTaskSql.java:3437)

    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.executeOdiCommand(SnpSessTaskSql.java:1509)

    at oracle.odi.runtime.agent.execution.cmd.OdiCommandExecutor.execute(OdiCommandExecutor.java:44)

    at oracle.odi.runtime.agent.execution.cmd.OdiCommandExecutor.execute(OdiCommandExecutor.java:1)

    at oracle.odi.runtime.agent.execution.TaskExecutionHandler.handleTask(TaskExecutionHandler.java:50)

    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2913)

    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2625)

    at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:577)

    at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:468)

    at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:2128)

    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$ 2.doAction(StartSessRequestProcessor.java:366)

    at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:216)

    at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.doProcessStartSessTask(StartSessRequestProcessor.java:300)

    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.access$ 0 (StartSessRequestProcessor.java:292)

    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$ StartSessTask.doExecute (StartSessRequestProcessor.java:855)

    at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:126)

    to oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$ 2.run(DefaultAgentTaskExecutor.java:82)

    at java.lang.Thread.run(Thread.java:662)

    Caused by: org.apache.commons.vfs2.FileSystemException: not able to connect to the server SFTP '10.232.9.123'.

    at org.apache.commons.vfs2.provider.sftp.SftpClientFactory.createConnection(SftpClientFactory.java:230)

    at org.apache.commons.vfs2.provider.sftp.SftpFileProvider.doCreateFileSystem(SftpFileProvider.java:96)

    ... more than 26

    Caused by: com.jcraft.jsch.JSchException: Auth fail

    at com.jcraft.jsch.Session.connect(Session.java:451)

    at com.jcraft.jsch.Session.connect(Session.java:149)

    at org.apache.commons.vfs2.provider.sftp.SftpClientFactory.createConnection(SftpClientFactory.java:226)

    ... more than 27

    Hi Aramast,

    Thank you very much for your answers. I realized that I had not encoded password. I coded and it worked like a charm.

    See you soon!

  • Logon credentials failed timer code missing

    Apex 4.2.2.00.11 on Oracle 11.2.x

    Mobile login page (using a custom region based on the region-with-title (some minor rendering mods) does not include the Javascript for the countdown when the logon credentials auth fails.

    This is what is generated:

    apex.jQuery (' div [id = P1001]: last ') .one ('pageinit', function() {}
    (function() {apex.da.initDaEventList ;})) ();
    (function() {apex.da.init ;})) ();
    });

    The code block whole timer

    (function() {}
    var lTimeoutField = document.getElementById ("apex_login_throttle_sec"),

    .. etc...

    .. is missing from this code.

    I don't think it's the custom zone, as top of the region-with-title has the same behavior. Not have modded all existing regions over there (with the exception of the addition of a new). So I'm a little lost as to where I stuffed up. It seems that the page that deals now does not recognize a failure, and despite adding the div notification message and the countdown timer, the code to update and make the countdown is not included.

    You will appreciate pointers in the right direction. Thank you.

    Found the problem. XHR call was made (i.e. missing Javascript) as long as the cache attribute browser security has been set. False parameter attribute results in a call from POST and a page refresh (which now contains the Javascript countdown).

  • Add Standalone workflow fails...

    I'm clearly missing something in what concerns the use Orchestrator and hope I can a little nudge in the right direction.

    I tried to add a stand-alone ESXi 4.1 host to vCenter Server. The workflow for adding a stand-alone host (Workflows > vCenter > host management > recording > Add standalone host) fails everytime I try to use it. The error message I see is:

    "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)

    I can't find out where to install the host SSL certificate. This error refers to the vCenter Server SSL certificate or the ESXi host SSL certificate?

    Thank you, in advance, for your help.

    =======================================

    Here's my vCO log file:

    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    Connection with the key pair (.. / server/vmo/conf/vco_key)
    Cannot run command InternalError: identity file not found! (Workflow: run SSH command / command run SSH (item6) #14) (Workflow: run SSH command / command run SSH (item6) #31)
    Login with password
    Cannot run command InternalError: Auth fail (Workflow: run SSH command / command run SSH (item6) #14) (Workflow: run SSH command / command run SSH (item6) #31)
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    Login with password
    Cannot run command InternalError: java.net.ConnectException: Connection refused: connect (Workflow: run SSH command / command run SSH (item6) #14) (Workflow: run SSH command / run SSH Command (item6) #31)
    (com.vmware.library.ssh/registerVSOonHost) Registration of public key VS - O on ' 172.20.10.51' for the user 'root' failed. InternalError: java.net.ConnectException: connection refused: connect (name of the dynamic Script Module: registerVSOonHost #5) (name of the dynamic Script Module: registerVSOonHost #30)
    (com.vmware.library.ssh/registerVSOonHost) Registration of public key VS - O on ' 172.20.10.51' for the user 'root' failed. InternalError: Auth fail (name of the dynamic Script Module: registerVSOonHost #5) (name of the dynamic Script Module: registerVSOonHost #30)
    (com.vmware.library.ssh/registerVSOonHost) Registration of public key VS - O on ' 172.20.10.52' for the user 'root' failed. InternalError: java.net.ConnectException: connection refused: connect (name of the dynamic Script Module: registerVSOonHost #5) (name of the dynamic Script Module: registerVSOonHost #30)
    (com.vmware.library.ssh/registerVSOonHost) Registration of public key VS - O on ' 172.20.10.52' for the user 'root' failed. InternalError: Auth fail (name of the dynamic Script Module: registerVSOonHost #5) (name of the dynamic Script Module: registerVSOonHost #30)
    Login with password
    Connected!
    Execution of 'uptime '.
    Output: ' 04:27:11 up to 12 min, load average: 0.00, 0.00, 0.00
    '
    Error: "
    Exit code: '0'
    Uptime - exit: 04:27:11 to 12 minutes, load average: 0.00, 0.00, 0.00

    error:
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    Login with password
    Connected!
    Execution of 'uptime '.
    Output: ' 21:28:41 until 02:39, load average: 0.00, 0.00, 0.00
    '
    Error: "
    Exit code: '0'
    Uptime - exit: 21:28:41 until 02:39, load average: 0.00, 0.00, 0.00

    error:
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    Login with password
    Connected!
    'Vmware' running - v
    Output: "VMware ESXi 4.1.0 build-260247
    '
    Error: "
    Exit code: '0'
    out of VMware - v -: VMware ESXi 4.1.0 build-260247

    error:
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)
    (com.vmware.library.vc.basic/vim3WaitTaskEnd) "AddStandaloneHost_Task" task error: the authenticity of the host SSL certificate is not verified. (Name of the dynamic Script Module: vim3WaitTaskEnd #20)

    Hi Ken!

    It's a well-known (not good) workflow limitation included.

    Find the solution here:

    http://communities.VMware.com/docs/doc-14363

    Thanks goes to Andreas :-)!

    Cordially, and have fun with vCO :-)

    Joerg

  • ASA 5505. VPN Site-to-Site does not connect!

    Hello!
    Already more than a week there, as we had a new channel of communication of MGTSa (Ontario terminal Sercomm RV6688BCM, who barely made in the 'bridge' - had to do the provider in order to receive our white Cisco Ip address), and now I train as well more that one week to raise between our IKEv1 IPsec Site-to-Site VPN tunnel closes offices.
    Configurable and use the wizard in ASDM and handles in the CLI, the result of a year, the connection does not rise.
    Cisco version 9.2 (2), the image of the Cisco asa922 - k8.bin, Security Plus license version, version 7.2 AMPS (2).
    What I'll never know...
    Debugging and complete configuration enclose below.
    Help, which can follow any responses, please! I was completely exhausted!

    Config:

    Output of the command: "sh run".

    : Saved
    :
    : Serial: XXXXXXXXXXXX
    : Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
    :
    ASA Version 9.2 (2)
    !
    hostname door-71
    activate the encrypted password of F6OJ0GOws7WHxeql
    names of
    IP local pool vpnpool 10.1.72.100 - 10.1.72.120 mask 255.255.255.0
    !
    interface Ethernet0/0
    switchport access vlan 2
    !
    interface Ethernet0/1
    !
    interface Ethernet0/2
    !
    interface Ethernet0/3
    !
    interface Ethernet0/4
    !
    interface Ethernet0/5
    !
    interface Ethernet0/6
    !
    interface Ethernet0/7
    !
    interface Vlan1
    nameif inside
    security-level 100
    IP 10.1.72.254 255.255.255.0
    !
    interface Vlan2
    nameif outside_mgts
    security-level 0
    62.112.100.R1 255.255.255.252 IP address
    !
    passive FTP mode
    clock timezone 3 MSK/MSD
    clock to DST MSK/MDD recurring last Sun Mar 02:00 last Sun Oct 03:00
    DNS lookup field inside
    DNS server-group MGTS
    Server name 195.34.31.50
    permit same-security-traffic inter-interface
    permit same-security-traffic intra-interface
    network obj_any object
    subnet 0.0.0.0 0.0.0.0
    network of the NET72 object
    10.1.72.0 subnet 255.255.255.0
    network object obj - 0.0.0.0
    host 0.0.0.0
    network of the Nafanya object
    Home 10.1.72.5
    network object obj - 10.1.72.0
    10.1.72.0 subnet 255.255.255.0
    network of the NET61 object
    10.1.61.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_10.1.72.96_27 object
    subnet 10.1.72.96 255.255.255.224
    network of the NETT72 object
    10.1.72.0 subnet 255.255.255.0
    network of the NET30 object
    10.1.30.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_10.1.72.0_24 object
    10.1.72.0 subnet 255.255.255.0
    object-group service OG INET
    the purpose of the echo icmp message service
    response to echo icmp service object
    service-object icmp traceroute
    service-object unreachable icmp
    service-purpose tcp - udp destination eq echo
    the DM_INLINE_NETWORK_1 object-group network
    network-object NET30
    network-object, object NET72
    DM_INLINE_TCP_1 tcp service object-group
    port-object eq www
    EQ object of the https port
    inside_access_in extended access list permit ip object NET72 object-group DM_INLINE_NETWORK_1
    access extensive list ip 10.1.72.0 inside_access_in allow 255.255.255.0 any
    inside_access_in extended access list permit ip object Nafanya any idle state
    inside_access_in list extended access allowed object-group OG INET an entire
    inside_access_in of access allowed any ip an extended list
    inside_access_in list extended access deny ip any alerts on any newspaper
    outside_mgts_access_in list extended access allowed object-group OG INET an entire
    outside_mgts_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
    outside_mgts_access_in list extended access deny ip any alerts on any newspaper
    access extensive list ip 10.1.72.0 outside_mgts_cryptomap allow 255.255.255.0 object NET61
    VPN-ST_splitTunnelAcl permit 10.1.72.0 access list standard 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Within 1500 MTU
    outside_mgts MTU 1500
    IP check path reverse interface outside_mgts
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    no permit-nonconnected arp
    NAT (inside outside_mgts) static source NET72 NET72 NETWORK_OBJ_10.1.72.96_27 NETWORK_OBJ_10.1.72.96_27 non-proxy-arp-search of route static destination
    NAT (inside outside_mgts) static source NETWORK_OBJ_10.1.72.0_24 NETWORK_OBJ_10.1.72.0_24 NET61 NET61 non-proxy-arp-search of route static destination
    !
    network obj_any object
    NAT (inside outside_mgts) dynamic obj - 0.0.0.0
    network of the NET72 object
    NAT (inside outside_mgts) interface dynamic dns
    inside_access_in access to the interface inside group
    Access-group outside_mgts_access_in in the outside_mgts interface
    Route 0.0.0.0 outside_mgts 0.0.0.0 62.112.100.R 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    without activating the user identity
    identity of the user by default-domain LOCAL
    AAA authentication http LOCAL console
    the ssh LOCAL console AAA authentication
    Enable http server
    http 10.1.72.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    card crypto outside_mgts_map 1 match address outside_mgts_cryptomap
    card crypto outside_mgts_map 1 set pfs Group1
    peer set card crypto outside_mgts_map 1 91.188.180.42
    card crypto outside_mgts_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_mgts_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    card crypto outside_mgts_map interface outside_mgts
    inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    inside crypto map inside_map interface
    Crypto ca trustpoint ASDM_TrustPoint0
    registration auto
    E-mail [email protected] / * /
    name of the object CN = door-71
    Serial number
    IP address 62.112.100.42
    Proxy-loc-transmitter
    Configure CRL
    Crypto ca trustpoint ASDM_TrustPoint1
    registration auto
    ASDM_TrustPoint1 key pair
    Configure CRL
    trustpool crypto ca policy
    string encryption ca ASDM_TrustPoint0 certificates
    certificate eff26954
    30820395 3082027d a0030201 020204ef f2695430 0d06092a 864886f7 0d 010105
    019
    6460ae26 ec5f301d 0603551d 0e041604 14c9a3f2 d70e6789 38fa4b01 465d 1964
    60ae26ec 5f300d06 092 has 8648 01050500 03820101 00448753 7baa5c77 86f70d01
    62857b 65 d05dc91e 3edfabc6 7b3771af bbedee14 673ec67d 3d0c2de4 b7a7ac05
    5f203a8c 98ab52cf 076401e5 1a2c6cb9 3f7afcba 52c617a5 644ece10 d6e1fd7d
    28b57d8c aaf49023 2037527e 9fcfa218 9883191f 60b221bf a561f2be d6882091
    0222b7a3 3880d6ac 49328d1f 2e085b15 6d1c1141 5f850e5c b6cb3e67 0e373591
    94a 82781 44493217 and 38097952 d 003 5552 5c445f1f 92f04039 a23fba20 b9d51b13
    f511f311 d1feb2bb 6d056a15 7e63cc1b 1f134677 8124c 024 3af56b97 51af8253
    486844bc b1954abe 8acd7108 5e4212df db835d76 98ffdb2b 8c8ab915 193b 8167
    0db3dd54 c8346b96 c4f4eff7 1e7cd576 a8b1f86e 3b868a6e 89
    quit smoking
    string encryption ca ASDM_TrustPoint1 certificates
    certificate a39a2b54
    3082025f 30820377 a0030201 020204 has 3 9a2b5430 0d06092a 864886f7 0d 010105
    0500304 06035504 03130767 36313137 30120603 55040513 6174652d 3110300e b
       
    c084dcd9 d250e194 abcb3eb8 1da93bd0 fb0dba1a b1c35b43 d547a841 5d4ee1a4
    14bdb207 7dd790a4 0cd 70471 5f3a896a 07bd56dc ea01b3dd 254cde88 e1490e97
    f3e54c05 551adde0 66aa3782 c85880c2 b162ec29 4e49346a df71062d 6d6d8f49
    62b9de93 ba07b4f7 a50e77e1 8f54b32b 6627cb27 e982b36f a 362973, 0 88de3272
    9bd6d4d2 8ca1e11f 214f20a9 78bdea95 78fdc45c d6d45674 6acb9bcb d0bd930e
    638eedfe cd559ab1 e1205c48 3ee9616f e631db55 e82b623c 434ffdc1 11020301
    0001 has 363 3061300f 0603551d 130101ff 0101ff30 04053003 0e060355 1d0f0101
    ff040403 1f060355 02018630 230418 30168014 0cea70bf 0d0e0c4b eb34a0b1 1 d
    8242 has 549 0603 551d0e04 1604140c ea70bf0d 0e0c4beb 34a0b182 301D 5183ccf9
    42a 54951 010105 05000382 0101004e 7bfe054a 0d 864886f7 0d06092a 83ccf930
    d434a27c 1d3dce15 529bdc5f 70a2dff1 98975de9 2a97333b 96077966 05a8e9ef
    bf320cbd ecec3819 ade20a86 9aeb5bde bd129c7b 29341e4b edf91473 f2bf235d
    9aaeae21 a629ccc6 3c79200b b9a89b08 bf38afb6 ea56b957 4430f692 a 4745, 411
    34d71fad 588e4e18 2b2d97af b2aae6b9 b6a22350 d031615b 49ea9b9f 2fdd82e6
    ebd4dccd df93c17e deceb796 f268abf1 881409b 5 89183841 f484f0e7 bd5f7b69
    ebf7481c faf69d3e 9d24df6e 9c2b0791 785019f7 a0d20e95 2ef35799 66ffc819
    4a77cdf2 c6fb4380 fe94c13c d4261655 7bf3d6ba 6289dc8b f9aad4e1 bd918fb7
    32916fe1 477666ab c2a3d591 a84dd435 51711f6e 93e2bd84 89884c
    quit smoking
    crypto isakmp identity address
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev2 activate outside_mgts port 443 customer service
    Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
    Crypto ikev1 allow inside
    Crypto ikev1 enable outside_mgts
    IKEv1 crypto policy 10
    authentication crack
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 20
    authentication rsa - sig
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 30
    preshared authentication
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 40
    authentication crack
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 50
    authentication rsa - sig
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 60
    preshared authentication
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 70
    authentication crack
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 80
    authentication rsa - sig
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 90
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 100
    authentication crack
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 110
    authentication rsa - sig
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 120
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 130
    authentication crack
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 140
    authentication rsa - sig
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 150
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    without ssh stricthostkeycheck
    SSH 10.1.72.0 255.255.255.0 inside
    SSH timeout 60
    SSH group dh-Group1-sha1 key exchange
    Console timeout 0
    vpnclient Server 91.188.180.X
    vpnclient mode network-extension-mode
    vpnclient nem-st-autoconnect
    VPN - L2L vpnclient vpngroup password *.
    vpnclient username aradetskayaL password *.
    dhcpd auto_config outside_mgts
    !
    dhcpd update dns replace all two interface inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    SSL-trust ASDM_TrustPoint0 inside point
    SSL-trust ASDM_TrustPoint0 outside_mgts point
    WebVPN
    Select outside_mgts
    internal GroupPolicy_91.188.180.X group strategy
    attributes of Group Policy GroupPolicy_91.188.180.X
    Ikev1 VPN-tunnel-Protocol
    internal group VPN - ST strategy
    attributes of group VPN - ST policy
    value of 195.34.31.50 DNS Server 8.8.8.8
    Ikev1 VPN-tunnel-Protocol
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value VPN-ST_splitTunnelAcl
    by default no
    aradetskayaL encrypted HR3qeva85hzXT6KK privilege 15 password username
    tunnel-group 91.188.180.X type ipsec-l2l
    attributes global-tunnel-group 91.188.180.X
    Group - default policy - GroupPolicy_91.188.180.42
    IPSec-attributes tunnel-group 91.188.180.X
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    remotely IKEv2 authentication certificate
    pre-shared-key authentication local IKEv2 *.
    remote access to tunnel-group VPN - ST type
    VPN-general ST-attributes tunnel-group
    address vpnpool pool
    Group Policy - by default-VPN-ST
    tunnel-group ipsec VPN ST-attributes
    IKEv1 pre-shared-key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    inspect the icmp error
    !
    global service-policy global_policy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:212e4f5035793d1c219fed57751983d8
    : end

    door-71 # sh crypto ikev1 his

    There are no SAs IKEv1

    door-71 # sh crypto ikev2 his

    There are no SAs IKEv2

    door-71 # sh crypto ipsec his


    There is no ipsec security associations
    door-71 # sh crypto isakmp

    There are no SAs IKEv1

    There are no SAs IKEv2

    Global statistics IKEv1
    The active Tunnels: 0
    Previous Tunnels: 0
    In bytes: 0
    In the packages: 0
    In packs of fall: 0
    In Notifys: 0
    In the constituencies of P2: 0
    In P2 invalid Exchange: 0
    In P2 Exchange rejects: 0
    Requests for removal in his P2: 0
    Bytes: 0
    Package: 0
    Fall packages: 0
    NOTIFYs out: 0


    Exchanges of P2: 0
    The Invalides Exchange P2: 0
    Exchange of P2 rejects: 0
    Requests to remove on P2 Sa: 0
    Tunnels of the initiator: 0
    Initiator fails: 0
    Answering machine fails: 0
    Ability system breaks down: 0
    AUTH failed: 0
    Decrypt failed: 0
    Valid hash fails: 0
    No failure his: 0

    IKEV1 statistics for Admission appeals
    In negotiating SAs Max: 25
    In negotiating SAs: 0
    In negotiating SAs Highwater: 0
    In negotiating SAs rejected: 0

    Global statistics IKEv2
    The active Tunnels: 0
    Previous Tunnels: 0
    In bytes: 0
    In the packages: 0
    In packs of fall: 0
    In Fragments of fall: 0
    In Notifys: 0
    In Exchange for the P2: 0
    In P2 invalid Exchange: 0
    In P2 Exchange rejects: 0
    In IPSEC delete: 0
    In delete IKE: 0
    Bytes: 0
    Package: 0
    Fall packages: 0
    Fragments of fall: 0
    NOTIFYs out: 0
    Exchange of P2: 0
    The Invalides Exchange P2: 0
    Exchange of P2 rejects: 0
    On IPSEC delete: 0
    The IKE Delete: 0
    Locally launched sAs: 0
    Locally launched sAs failed: 0
    SAs remotely initiated: 0
    SAs remotely initiated failed: 0
    System capacity: 0
    Authentication failures: 0
    Decrypt failures: 0
    Hash failures: 0
    Invalid SPI: 0
    In the Configs: 0
    Configs: 0
    In the Configs rejects: 0
    Configs rejects: 0
    Previous Tunnels: 0
    Previous Tunnels wraps: 0
    In the DPD Messages: 0
    The DPD Messages: 0
    The NAT KeepAlive: 0
    IKE recomposition launched locally: 0
    IKE returned to the remote initiated key: 0
    Generate a new key CHILD initiated locally: 0
    CHILD given to the remote initiated key: 0

    IKEV2 statistics for Admission appeals
    Max active SAs: no limit
    Max in negotiating SAs: 50
    Challenge cookie line: never
    Active sAs: 0
    In negotiating SAs: 0
    Incoming requests: 0
    Accepted incoming requests: 0
    A rejected incoming requests: 0
    Out of requests: 0
    Out of the applications accepted: 0
    The outgoing rejected requests: 0
    A rejected queries: 0
    Rejected at the SA: 0 Max limit
    Rejected low resources: 0
    Rejected the current reboot: 0
    Challenges of cookie: 0
    Cookies transmitted challenges: 0
    Challenges of cookie failed: 0

    IKEv1 global IPSec over TCP statistics
    --------------------------------
    Embryonic connections: 0
    Active connections: 0
    Previous connections: 0
    Incoming packets: 0
    Inbound packets ignored: 0
    Outgoing packets: 0
    Outbound packets ignored: 0
    The RST packets: 0
    Heartbeat Recevied ACK packets: 0
    Bad headers: 0
    Bad trailers: 0
    Chess timer: 0
    Checksum errors: 0
    Internal error: 0

     
    door-71 # sh statistical protocol all cryptographic
    [Statistics IKEv1]
    Encrypt packets of requests: 0
    Encapsulate packets of requests: 0
    Decrypt packets of requests: 0
    Decapsulating requests for package: 0
    HMAC calculation queries: 0
    ITS creation queries: 0
    SA asked to generate a new key: 0
    Deletion requests: 0
    Next phase of allocation key applications: 0
    Number of random generation queries: 0
    Failed requests: 0
    [Statistics IKEv2]
    Encrypt packets of requests: 0
    Encapsulate packets of requests: 0
    Decrypt packets of requests: 0
    Decapsulating requests for package: 0
    HMAC calculation queries: 0
    ITS creation queries: 0
    SA asked to generate a new key: 0
    Deletion requests: 0
    Next phase of allocation key applications: 0
    Number of random generation queries: 0
    Failed requests: 0
    [IPsec statistics]
    Encrypt packets of requests: 0
    Encapsulate packets of requests: 0
    Decrypt packets of requests: 0
    Decapsulating requests for package: 0
    HMAC calculation queries: 0

    ITS creation queries: 0
    SA asked to generate a new key: 0
    Deletion requests: 0
    Next phase of allocation key applications: 0
    Number of random generation queries: 0
    Failed requests: 0
    [SSL statistics]
    Encrypt packets of queries: 19331
    Encapsulate packets of queries: 19331
    Decrypt packets of queries: 437
    Package requests decapsulating: 437
    HMAC calculation queries: 19768
    ITS creation queries: 178
    SA asked to generate a new key: 0
    Requests to remove SA: 176
    Next phase of allocation key applications: 0
    Number of random generation queries: 0
    Failed requests: 0
    [Statistical SSH are not taken in charge]
    [Statistics SRTP]
    Encrypt packets of requests: 0
    Encapsulate packets of requests: 0
    Decrypt packets of requests: 0
    Decapsulating requests for package: 0
    HMAC calculation queries: 0
    ITS creation queries: 0
    SA asked to generate a new key: 0
    Deletion requests: 0
    Next phase of allocation key applications: 0
    Number of random generation queries: 0
    Failed requests: 0
    [Statistics]
    Encrypt packets of requests: 0
    Encapsulate packets of requests: 0
    Decrypt packets of requests: 0
    Decapsulating requests for package: 0
    HMAC calculation queries: 6238
    ITS creation queries: 0
    SA asked to generate a new key: 0
    Deletion requests: 0
    Next phase of allocation key applications: 0
    Number of queries random generation: 76
    Failure of queries: 9

    door-71 # sh crypto ca trustpoints

    Trustpoint ASDM_TrustPoint0:
    Configured for the production of a self-signed certificate.

    Trustpoint ASDM_TrustPoint1:
    Configured for the production of a self-signed certificate.

    If you need something more, then spread!
    Please explain why it is that I don't want to work?

    Hello

    When the IPSEC tunnel does not come to the top, the first thing comes to my mind is to run a tracer of package from the CLI and the phases in it. Please run this command from your firewall side and share the output. I've just compiled this command with the random ip address and ports of your given range.

    Packet-trace entry inside tcp 10.1.72.2 1233 10.1.61.2 443 detailed

    Best regards

    Amandine

  • I can't send emails. has been before and nothing has changed since I did.

    'Calcutta shorts', account: ' * address email is removed from the privacy *', server: 'outgoing.verizon.net', Protocol: SMTP, Port: 25, secure (SSL): no, error number: 0x800CCC17

    Account: ' * address email is removed from the privacy *', server: 'incoming.verizon.net', Protocol: POP3, server response: '-ERR [AUTH] failed authentication ', Port: 110, secure (SSL): no, Server error: 0x800CCC90, error number: 0x800CCC92

    1. name of the account is supposed to be your username. Do you use your e-mail address as your user name, or it IS a username that you have neglected to use?

    2 re: incoming.verizon.net... is part of the error message '-ERR [AUTH] Authentication failed',
    Did you put a check on "connect using password authentication secure"? You're NOT supposed to.

    Here is a link that you can compare your settings against.
    NOTE : the link says Outlook Express. It is ok. OE and WM using the same settings.

    t-4-2

  • password is incorrect, and I can remember. Windows Live Mail error ID: 0x800CCC92

    Original title:

    Do not know my password

    I have currently Windows Live Mail downloaded on my computer and my emails cannot send or receive because my password is incorrect, and I can remember because I did almost a decade ago. I was wondering if there was a way to reset. I tried the https://account.live.com/resetpassword.aspx, but this page is only for accounts that work through windows online. Is the message it displays when I try and send/receive mail: cannot send or receive messages for the Optonline account (auto1). An incorrect password was entered. The next time that you send or receive messages, you will be asked to enter your user name and password for this account.

    Server error: 0x800CCC90
    Server response:-ERR [AUTH] failed authentication
    Server: 'mail.optonline.net.
    Windows Live Mail error ID: 0x800CCC92
    Protocol: POP3
    Port: 110
    Secure (SSL): No.

    I was wondering if there is anything I can do to solve this problem. I don't know how many characters my password isn't all passwords I use doesn't seem to work.

    Thank you

    Visit http://optonline.net and use the options here to reset your password. Once you have a new password, work you give access to your mailbox online, right-click on the account name in the Windows Live Mail Folders pane and select Properties. Enter the new password in the servers tab.

    Dial a new test message with a single subject, then send it to yourself. Post a new message in your response.

  • Can't send or receive messages Windows Live Mail 2012 / Cogeco account

    Until yesterday, my Cogeco email account worked well within Windows Live Mail 2012. Bought a laptop and I tried to add this account to it.

    The following message appears when I try to send/receive:

    and then the following error message appears:

    Can't send or receive messages on behalf of Cogeco (wliber). An incorrect password was entered. The next time that you send or receive messages, you will be asked to enter your user name and password for this account.

    Server error: 0x800CCC90

    Server response:-ERR [AUTH] failed authentication

    Server: 'pop.cogeco.ca '.

    Windows Live Mail error ID: 0x800CCC92

    Protocol: POP3

    Port: 110

    Secure (SSL): No.

    Went in properties and changed the password to what I think it should be and also changed the secure (SSL) to Yes for incoming and outgoing messages, but still can not send/receive, keep coming back that my password is incorrect.

    Tried to create another account of cogeco, but who also do not send/receive.

    MICROSOFT DOES NOT SUPPORT FOR WINDOWS LIVE MAIL. NEED HELP!  and thank all who respond in advance.

    See: http://www.cogeco.ca/web/on/en/residential/support/5/478/faq-internet/email-configuration/how-do-i-configure-windows-live-mail-pop

Maybe you are looking for