Current entry port analog for BNC-2110

Similar Questions

• What is the current max on the digital output of a Terminal BNC - 2110

  Im a using a card of data acquisition of 6221 with a block of connection BNC-2110 connected to it. For the e/s digital terminal block provides an additional 5V input. Unfortunately I don't seem to find any information as to know if this provides additional current to the TTL signal or no training. Is there an internal pilot in the terminal block, or - if I need to connect external relays to the digital output - always connect a current driver in between?

  Thank you

  Wolfgang

  You can replay the 6221 and BN_2110 manual. The + 5V pins are outputs of the DAQ card - they are not entries.

  Yes, you will need external circuits if the external relays require more current than can provide the DAQ card.

• Strange problem with analog output PCI 6251 and BNC-2110

  I'm controlling current source of third parties using the connectors of analog output on my card PCI 6251 and BNC-2110.

  The current source needs an input signal of 0.1V. I tested it using a battery, the potentiometer and the voltmeter, and by manually adjusting the voltage of power current works - current output with control voltage scales according to the specifications and is relatively stable.

  The data acquisition card works too - when I connect a voltmeter to the AO0 AO1, the measured voltage corresponds to the target with great precision value.

  But when I connect the current source of third AO0 AO1 data acquisition card, the measured output voltage drops and fluctuates. This applies to both channels of the AO.

  I wonder what is the problem here. I suspect it could be a matter of the grounding - the current analog control of the source is an entry with two floating terminals differential. I tried to return the switches FS/GS on the BNC-2110, but that makes no difference.

  Anyone knows similar behavior? Does anyone have any suggestions?

  
  

• is that any limits the current entry for the digital I/o?

  Hi all

  I wonder if there is no limit on the input to the digital I/o port. I have a device about 0.2 volt voltage outputing and the manual says the maximum sink current is 25mA. I connect this signal to a DI entry in my 6711 map. I wonder if the current is too large for the entrance of DI or the PFI?

  As we have already mentioned, there is no current flowing on the device in low level mode.

  The current specifications mentioned see the maximum current that can be managed by the device in low level mode.

  I hope not to confuse you more than necessary. On a row of data to the TTL level, nothing flowing from the device to the main circuit in level mode high current. In low mode, there is flowing in the main circuit in the current device. This current is inherently limited by the circuit.

  So, if you have a file specification of 25mA max. of the peripheral device in low level mode, it will never sink too much power from the main circuit. You can connect two devices without any risk. The maximum current is just specified in case you manage more current with the device, a led or a relay for example. In this case, the charge current must be limited, so that you do not damage the device. But - as mentioned - this is NOT the case in your application.

• BNC-2110 entry limit is 5V?

  Hello, I'm trying to measure the magnetic field by using hall sensor,

  I created wave sin simulated with amplitude 10V

  However, it seems that BNC-2110 is only measure up to +-5V?

  Is it OK to switch to 10V so I can display + 10V range?

  Thank you very much for your help!

  Page 3. The maximum range is of +/-10V.

• Problem with connection diagram - BNC-2110 to PCI 6280

  Hello

  I want to read analog input using BNC 2110 as an interface connected to the PCI-6280. In the first step I want to use the Signal Express to see only the data, but when I choose one of the input and then string I want to see the connection, I get this message:

  ------------------------------

  Connection scheme tool does not send the accessory on the connector 0 of your device:
  BNC-2110

  Please select one of the following accessories to display the supported connection diagram:

  Support for accessories:
  SCB-68

  CB-68LP

  TBX-68

  CB-68LPR

  SCC-68

  ------------------------------

  What should I do in this step?

  Hi MiladAk,

  There is this sentence in the Manual "the BNC-2110 is only intended for differential analog input signals. The 16 channels HAVE on PCI-6280 are mapped to 8 connectors BNC AI0 - AI7 on BNC-2110. HAVE [n] with I [n + 8] represent a differential channel. This means that if you select channel differential AI0 in Signal Express with Terminal configuration it will also use AI8. These two channels is represented by a single BNC connector (connection central driver is positive = AI0, negative connection is shielding = AI8).

  Best regards

  CaravagGIO

• PXI-6250 and BNC-2110 to 5V relay?

  I try to use the PXI-6250 by BNC-2110 relay 5V. Please advise if this is possible and how.

  Thank you

  Liming

  Hello liming,

  It is certainly possible, but there are some limitations.  Are there current requirements for the 5V relay.  If it is low current, you should have no problem controlling the relay with one of your PFI lines (they are located in the Terminal screw of the BNC-2110).

  

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• do you need a power supply to the current entry with data acquisition or 9265

  Hello I just receive the NI 9265 Daq for research in my lab. I'm trying to present entry and display it on an oscilloscope. I don't get anything. I did some research on the internet, so my question is do you need a power supply to the current entry with data acquisition or 9265?

  Read the data sheet.  Clearly on the first page is a sentence which reads "the NI 9265 requires 9 V to 36 V external power.

• BNC-2110, 6023E PCI card and Labview V9.0: is the sensitivity of data acquisition (change more little detectable voltage) 0.002V?

  BNC-2110, 6023E PCI card and Labview V9.0: sensitivity of data acquisition (change more little detectable voltage) is 0.002V

  Hi, I use the software/hardware above to read a voltage of a potentiostat world Precision Instruments No..

  I'm trying to record changes in voltage as low as 0.0003V but using the wizard DAQ, I seem to be limited to a sensitivity of 0.002V.  This is the limit of real sensitivity or have I missed something?

  Any help would be greatly appreciated.

  Hi DCAM77,

  Thanks for joining the forums!

  The PCI or 6023E has a 12-bit ADC.  In other words, it can make the difference between 4096 (2 ^ 12) different levels within the range of cards.  The card you have has a selectable range by ± 10 V, ± 5 V, ± 500 mV or ±50 mV software.

  This means that the minimum detectable variation will be 4 mV, 20 mV, 244 µV or 24, depending on the chosen range µV.

  You should be able to use the ± 500 mV or ±50 mV to get the least significant bit (LSB) value, you need, even if it means that your signal is located between these values.  If not, then you need to consider other materials to the application, or the addition of external circuits across the signal.

• It is current on the analog module USB NI 9263 output voltage limit (+/-10 v)?

  It is current on the analog module USB NI 9263 output voltage limit (+/-10 v)? I try to run a current controlled resistance, but cannot get the required current. The servovalved has a parallel internal resistance of 80 ohms and requires 20 my full operation. Ohm's law: (.02 A) * ((80*80) /(80+80) ohms = 4.5 v) Yet, the required voltage, do not move the servo. Outside the material error (continue this by other means), what could be the problem?

  Have you checked the Manual?

  Page 12 1 says my.

  For servo, you really need some kind of amplifier.  See if the manufacturer provides the electronic driver for it.

• How to get to a BNC-2110

  Hello world

  I have a vi that is 4 kHz of sampling data... At this rate, I would use the counter on my BNC-2110 for hardware DAQ BOF schedule rather than the clock on board... However, do not know how to obtain and use the data from the meter... I guess I need a thread linking some of the pins on the device (for example PF01, CRT0, etc., what are all these input/output pins for?) and the meter would be used in a certain type of setting to relax in vi code? I am beeing trying to figure this out for a while, but can't find anything which provids a nice simple description...

  Any help would be greatly appreciated.

  Kind regards

  Jack

  The sample clock is the clock that uses the A/D. The source is usually the internal clock on the DAQ hardware. You do not have access to the pc clock. Let the clock source inside and forget options for now.

• Hi I have a current plan of photography for £8.87 per month which is paid and up-to-date, it allows me to use PSCC and LR. I've updated the two about a week ago and now LR is ok but PS says it's now a trial and I want to buy it and my trial runs out soon?

  Hi I have a current plan of photography for £8.87 per month which is paid and up-to-date, it allows me to use PSCC and LR. I've updated the two about a week ago and now LR is ok but PS says it's now a trial and I want to buy it and my trial runs out soon? How can I get to the scene, I was up front with the full version of PS?

  Hello

  Please follow the steps below.

  Solution 1: -.

  1 sign out and sign back for creative cloud.

  https://helpx.Adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

  Solution 2: -.

  Check the "hosts" adobe entered into file. (If you don't see all the entries of adobe, go to solution 3)

  1. go to the location of the file "Hosts".

  WIN: C:\Windows\System32\drivers\etc

  MAC: Go to the menu finder on top > go to files > type '/ etc', press return.

  2. move the file hosts on the desktop.

  3. open.

  WIN: Open it with Notepad.

  MAC: double click on it.

  4 remove all entries of adobe, that it does not obstruct your machine to connect to the Adobe's Activation Server.

  5. rear move "/ etc" folder.

  Solution 3: -.

  1. check if you are using any kind of firewall (network/system) / proxy.

  2. turn off firewall / proxy.

  I hope this helps.

  Kind regards

  Vivet

• Need new ports USB for Satellite Pro L450D

  Hello

  I ve tried to keep new ports usb for my Toshiba Satellite Pro L450D I ve called Toshiba and they said I have to put it in for repair, but the thing is - it's not is no longer in warranty so that I can t make and send to Toshiba for repair.

  for me would cost loads I ve asked Toshiba provide me for my laptop usb ports, but they won t so I would like to know where I can get these parts as one of my ports usb don t work because of my daughter in the first place to break them and the entire interior of the usb ports is broken.

  Help, please
  Thank you

  Hello

  At first, I must say that Toshiba service doesn t sell these small parts such as USB ports. USB ports are soldered to the motherboard.
  Where to get the new USB ports? Good question.

  I don t know where you MFL, but perhaps you should I use Google in your country and check if you can find some independent repairer for laptop and ask for help.
  I fear it won't be so easy to find new ports of m.

  What you can try is to buy defective mainboard in the hope of USB ports are OK and are trying to replace them.

• HP Compaq 6000 Pro AIO: PCI Serial Port driver for HP Compaq 6000 Pro

  Hello world

  I could get help to find driver serial port PCI for HP Compaq 6000 Pro all in one workstation. It has 8.1 Windows x 64 installed. The hardware IDS are

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C & REV_03
  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C
  PCI\VEN_8086 & DEV_2E17 & CC_070002
  PCI\VEN_8086 & DEV_2E17 & CC_0700

  Thank you

  Vignesh

  Hello:

  You need this driver... Install manually if auto installation does not work.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4210069&swItemId=vc_85050_1&swEnvOid=4059

  You can see on the partial copy and paste installation information file driver that the ID you have posted is supported by this driver.

  ; Drivers
  ;----------------------------------------------------------
  [Manufacturer]
  Intel % = Intel, NTamd64

  [Intel.NTamd64]
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E07 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E17 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E27 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E37 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E97 & CC_0700"