CVP - model with SIP full appellate courts

Hello

We strive to set up the CVP model of full appellate with ICM and SIP. We are facing problems in calling the CVP server to hit the phone number and call the simple routing script. Please find the event that we receive in the PIM CPB console like below:

15:49:54 target allocation to 20 unknown CallID (serviceNum = 2 callingIDType = 70, callingDev = calledDev = 6553600 5555).

REDA

You must then two network VRU. A type 5 for the leg of the switch, if the label is not used; and a type 7 for leg VRUS, where etiquette is very important and the number of digits must match what is configured in AppAdmin, so that the VB knows where lives the correlation ID. See JPG.

This is explained in the configuration Guide for the CVP.

Kind regards

Geoff

Tags: Cisco Support

Similar Questions

  • Problems with SIP when saved in VCSE

    Hi guys,.

    VCSE and VCSC are both on X5.2. When a customer movi entered the VCSE and we try to dial in the MPS800 which is registered to the VCSC participants receive no video or audio. However even when call is made by using the thin fucntions H323 call. Is it possible to force the vcse do a h323 through the firewall on the highway.

    Thank you

    No, you must configure VCS - C address as the address of the SIP on MPS server.

    In the otherwise static Conference SIP and unique dial number with SIP don't enroll not on VCS - C.

    For VCS sent the appeal to members when receiving URL Conference personal other, you must configure in the shot (just repeat what I mentioned earlier).

    ====================================================================================

    [MPS]

    -SIP server: the VCS - C IP address

    -Default transport protocol: TCP (you can use TLS if you want)

    -Configure the personal URL of conference (with a specific format can easily configure rule research on VCS to MPS not to overlap with other aliases to point of termination/SIP UA).

    [CV]

    -Neighbouring area

    Type: neighbor

    H323 Mode: Off

    SIP: Mode: on

    SIP port: 5060 (assume MPS transport protocol configured as TCP)

    SIP Transport: TCP (suppose MPS transport protocol configured as TCP)

    Peer 1 address: address IP SC SPM

    Area profile: default

    -Rule search

    Mode: Alias matching

    Model type: Regex

    String pattern: [email protected] / * / (personal Conference suppose aliases is [email protected] / * /)

    Model behavior: leave

    Target: MPS-SIP-neighbor (this is the nearby area SIP created and point members)

    ====================================================================================

    With above configuration, VCS - C before calling SIP with the URL [email protected] / * / forward to members of Parliament.

    I would recommend you first do a test call in VCS - C (do not call VCS - e) to verify the call.

  • TC7.2.1 problems with SIP calls

    Hi, we had the following problem with sip calls:

    Here is the log:

    Version of the VCS software: Platform X7.2.3 | X8.2.1 Labor

    ______________________________________________________________________________

    Call with TC 7.2.1 does not
    ______________________________________________________________________________

    SIPMSG:
    | INVITE sip: [email protected] / * / SIP/2.0
    Via: SIP/2.0/TCP xx.xxx.60.133:57597; branch = z9hG4bK38f566387dbd719702049ddcb2590ebe.1; rport
    Call ID: 4832bd6a60d9d3d43670c55c573667ec
    CSeq: INVITE 101
    Contact: sip: [email protected] / * /: 57597; gr = urn: uuid:6 c 856033-4cbd - 5 b 15 - bb13 - 0715c4a694cd, ob>
    From: "201101102_C40_ServiceDesk" sip: [email protected] / * />; tag = d25377890df67530
    To: sip: [email protected] / * />
    Max-Forwards: 70
    Directions: sip:xx.xxx.1.51; lr>
    Allow: INVITE, ACK, CANCEL, BYE, update, INFO, OPTIONS, CONSULT, INFORM
    User-Agent: TANDBERG/521 (TC7.2.1.cb31c3d)
    "Proxy-Authorization: Digest ="bb1d830b2d64949caaadfb732cd7ca77414a991699854e8971970a68fe06"nonce, realm ="tplabvcsc01.xyz.com", qop = auth, opaque = 'AwAAAMSaxlh37 + YNQULdXHDdMkXYHVQ1', user name =" ", uri ="sip:xyz.com", answer is"51f225da16a3ac710e86c1b1b5815438", algorithm = MD5, nc = 00000008 cnonce ="21c839c8313e8f7f7477786cb40c5ee6. "
    Supported: replaces, timer, 100rel, gruu, way, way out
    Session time-out: 1800
    Content-Type: application/sdp
    Content-Length: 2842
     
    v = 0
    o = xx.xxx.60.133 IN IP4 6 2 tandberg
    s = -.
    c = IN IP4 xx.xxx.60.133
    b = AS:6000
    t = 0 0
    m = audio 16424 RTP/AVP 107 108 109 110 104 105 9 15 18 8 0 101
    b = TIAS: 128000
    a = rtpmap:107 m4as-LATM/90000
    a = fmtp:107 profile-level-id = 25; object = 23; bitrate = 128000
    a = rtpmap:108 m4as-LATM/90000
    a = fmtp:108 profile-level-id = 24; object = 23; bitrate = 64000
    a = rtpmap:109 m4as-LATM/90000
    a = fmtp:109 profile-level-id = 24; object = 23; bitrate = 56000
    a = rtpmap:110 m4as-LATM/90000
    a = fmtp:110 profile-level-id = 24; object = 23; bitrate = 48000
    a = rtpmap:104 G7221/16000
    a bitrate = 32000 fmtp:104 =
    a = rtpmap:105 G7221/16000
    a = fmtp:105 bitrate = 24000
    a = rtpmap:9 G722/8000
    a = rtpmap:15 G728/8000
    a G729/8000 rtpmap:18 =
    a = annex b fmtp:18 = yes
    a = rtpmap:8 PCMA/8000
    a = rtpmap:0 PCMU/8000
    a rtpmap:101 telephone-event/8000 =
    a = fmtp:101 0-15
    a = sendrecv
    m = video 16426 RTP / AVP 97 126 96 34 31
    b = TIAS: 6000000
    a = rtpmap:97 H264/90000
    a = packetization-mode=0;profile-level-id=428016;max-br=5000;max-mbps=245000;max-fs=9000;max-smbps=245000;max-fps=6000;max-rcmd-nalu-size=3456000 fmtp:97
    a = rtpmap:126 H264/90000
    a = packetization-mode=1;profile-level-id=428016;max-br=5000;max-mbps=245000;max-fs=9000;max-smbps=245000;max-fps=6000;max-rcmd-nalu-size=3456000 fmtp:126
    a = rtpmap:96 H263-1998/90000
    a = fmtp:96 custom = 1280, 768, 3; custom = 1280, 720, 3; custom = 1024, 768, 1; custom = 1024, 576, 2; custom = 800, 600, 1; cif4 = 1; custom = 720, 480, 1; custom = 640, 480, 1; custom = 512, 288, 1; CIF = 1; custom = 352, 240, 1; QCIF = 1; maxbr = 20000
    a = rtpmap:34 H263/90000
    a = fmtp:34 cif4 = 1; CIF = 1; QCIF = 1; maxbr = 20000
    a = rtpmap:31 H261/90000
    a cif fmtp:31 = = 1; QCIF = 1; maxbr = 20000
    a = label: 11
    a = answer: full
    a = content: hand
    a = rtcp-fb: * nack fold
    a = rtcp-fb: * ccm FIR
    a = rtcp-fb: * ccm tmmbr
    a = sendrecv
    m = application 28300 UDP/BFCP
    a = the installer: actpass
    a = confid:1
    a = userid:6
    a = floorid:2 mstrm:12
    a = floorctrl:c - s
    a = connection: new
    m = video 16428 RTP / AVP 97 126 96 34 31
    b = TIAS: 6000000
    a = rtpmap:97 H264/90000
    a = packetization-mode=0;profile-level-id=428016;max-br=5000;max-mbps=108000;max-fs=3840;max-smbps=108000;max-fps=6000;max-rcmd-nalu-size=1474560 fmtp:97
    a = rtpmap:126 H264/90000
    a = packetization-mode=1;profile-level-id=428016;max-br=5000;max-mbps=108000;max-fs=3840;max-smbps=108000;max-fps=6000;max-rcmd-nalu-size=1474560 fmtp:126


    a = rtpmap:96 H263-1998/90000
    a = fmtp:96 custom = 1280, 768, 3; custom = 1280, 720, 3; custom = 1024, 768, 1; custom = 1024, 576, 2; custom = 800, 600, 1; cif4 = 1; custom = 720, 480, 1; custom = 640, 480, 1; custom = 512, 288, 1; CIF = 1; custom = 352, 240, 1; QCIF = 1; maxbr = 20000
    a = rtpmap:34 H263/90000
    a = fmtp:34 cif4 = 1; CIF = 1; QCIF = 1; maxbr = 20000
    a = rtpmap:31 H261/90000
    a cif fmtp:31 = = 1; QCIF = 1; maxbr = 20000
    a = label: 12
    a = content: slides
    a = rtcp-fb: * nack fold
    a = rtcp-fb: * ccm FIR
    a = rtcp-fb: * ccm tmmbr
    a = sendrecv
    m = 16430 RTP/AVP 100 application
    a = rtpmap:100 H224/4800
    a = sendrecv
    m = application 29789 UDP/UDT/IX
    a = ixmap:0 ping
    a = ixmap:2 xccp
    |
    ________________________________________________________________________________________________

    Work of appeal with TC 7.1.4
    ________________________________________________________________________________________________

    SIPMSG:
    | INVITE sip: [email protected] / * / SIP/2.0
    Via: SIP/2.0/TCP xx.xxx.60.133:37491; branch = z9hG4bKe3dfed840a299516919a79e4a54cd707.1; rport
    Call ID: 480ec504782c0ad894929e882a696e74
    CSeq: INVITE 100
    Contact: sip: [email protected] / * /; gr = urn: uuid:6 c 856033-4cbd - 5 b 15 - bb13 - 0715c4a694cd, ob>
    From: "201101102_C40_ServiceDesk" sip: [email protected] / * />; tag = 3ab87b1c0d8b4d9d
    To: sip: [email protected] / * />
    Max-Forwards: 70
    Directions: sip:xx.xxx.1.51; lr>
    Allow: INVITE, ACK, CANCEL, BYE, update, INFO, OPTIONS, CONSULT, INFORM
    User-Agent: TANDBERG/520 (TC7.1.4.908e4a9)
    Supported: replaces, timer, 100rel, gruu, way, way out
    Session time-out: 1800
    Content-Type: application/sdp
    Content-Length: 2842
     
    v = 0
    o = xx.xxx.60.133 IN IP4 3 2 tandberg
    s = -.
    c = IN IP4 xx.xxx.60.133
    b = AS:6000
    t = 0 0
    m = audio 16394 RTP/AVP 107 108 109 110 104 105 9 15 18 8 0 101
    b = TIAS: 128000
    a = rtpmap:107 m4as-LATM/90000
    a = fmtp:107 profile-level-id = 25; object = 23; bitrate = 128000
    a = rtpmap:108 m4as-LATM/90000
    a = fmtp:108 profile-level-id = 24; object = 23; bitrate = 64000
    a = rtpmap:109 m4as-LATM/90000
    a = fmtp:109 profile-level-id = 24; object = 23; bitrate = 56000
    a = rtpmap:110 m4as-LATM/90000
    a = fmtp:110 profile-level-id = 24; object = 23; bitrate = 48000
    a = rtpmap:104 G7221/16000
    a bitrate = 32000 fmtp:104 =
    a = rtpmap:105 G7221/16000
    a = fmtp:105 bitrate = 24000
    a = rtpmap:9 G722/8000
    a = rtpmap:15 G728/8000
    a G729/8000 rtpmap:18 =
    a = annex b fmtp:18 = yes
    a = rtpmap:8 PCMA/8000
    a = rtpmap:0 PCMU/8000
    a rtpmap:101 telephone-event/8000 =
    a = fmtp:101 0-15
    a = sendrecv
    m = video 16396 RTP / AVP 97 126 96 34 31
    b = TIAS: 6000000
    a = rtpmap:97 H264/90000
    a = packetization-mode=0;profile-level-id=428016;max-br=5000;max-mbps=245000;max-fs=9000;max-smbps=245000;max-fps=6000;max-rcmd-nalu-size=3456000 fmtp:97
    a = rtpmap:126 H264/90000
    a = packetization-mode=1;profile-level-id=428016;max-br=5000;max-mbps=245000;max-fs=9000;max-smbps=245000;max-fps=6000;max-rcmd-nalu-size=3456000 fmtp:126
    a = rtpmap:96 H263-1998/90000
    a = fmtp:96 custom = 1280, 768, 3; custom = 1280, 720, 3; custom = 1024, 768, 1; custom = 1024, 576, 2; custom = 800, 600, 1; cif4 = 1; custom = 720, 480, 1; custom = 640, 480, 1; custom = 512, 288, 1; CIF = 1; custom = 352, 240, 1; QCIF = 1; maxbr = 20000
    a = rtpmap:34 H263/90000
    a = fmtp:34 cif4 = 1; CIF = 1; QCIF = 1; maxbr = 20000
    a = rtpmap:31 H261/90000
    a cif fmtp:31 = = 1; QCIF = 1; maxbr = 20000
    a = label: 11
    a = answer: full
    a = content: hand
    a = rtcp-fb: * nack fold
    a = rtcp-fb: * ccm FIR
    a = rtcp-fb: * ccm tmmbr
    a = sendrecv
    m = application 29489 UDP/BFCP
    a = the installer: actpass
    a = confid:1
    a = userid:3
    a = floorid:2 mstrm:12
    a = floorctrl:c - s
    a = connection: new
    m = video 16398 RTP / AVP 97 126 96 34 31
    b = TIAS: 6000000
    a = rtpmap:97 H264/90000


    a = packetization-mode=0;profile-level-id=428016;max-br=5000;max-mbps=108000;max-fs=3840;max-smbps=108000;max-fps=6000;max-rcmd-nalu-size=1474560 fmtp:97
    a = rtpmap:126 H264/90000
    a = packetization-mode=1;profile-level-id=428016;max-br=5000;max-mbps=108000;max-fs=3840;max-smbps=108000;max-fps=6000;max-rcmd-nalu-size=1474560 fmtp:126
    a = rtpmap:96 H263-1998/90000
    a = fmtp:96 custom = 1280, 768, 3; custom = 1280, 720, 3; custom = 1024, 768, 1; custom = 1024, 576, 2; custom = 800, 600, 1; cif4 = 1; custom = 720, 480, 1; custom = 640, 480, 1; custom = 512, 288, 1; CIF = 1; custom = 352, 240, 1; QCIF = 1; maxbr = 20000
    a = rtpmap:34 H263/90000
    a = fmtp:34 cif4 = 1; CIF = 1; QCIF = 1; maxbr = 20000
    a = rtpmap:31 H261/90000
    a cif fmtp:31 = = 1; QCIF = 1; maxbr = 20000
    a = label: 12
    a = content: slides
    a = rtcp-fb: * nack fold
    a = rtcp-fb: * ccm FIR
    a = rtcp-fb: * ccm tmmbr
    a = sendrecv
    m = 16400 RTP/AVP 100 application
    a = rtpmap:100 H224/4800
    a = sendrecv
    m = application 31127 UDP/UDT/IX
    a = ixmap:0 ping
    a = ixmap:2 xccp

    Another problem, indicated in diagnosis on a MX200 device tests, reporting problems of NTP. I tried to choose another NTP server - but this does not solve the problem, and it works with TC7.1.4. In addition to the time and date is wrong on the screen but OK on the touchscreen device.

    In addition, an error is reported on the OSD settings.

    Do you have advice?

    Thanks for help.
    |

    So, what's the problem? You just showed us an INVITATION. What is the configuration of your system? What is the reaction to INVITE him? We need complete diagnostic logs. Is this VCS - C registred? Where VCS - C diagnostic logs

  • Portege R830 - model with SSD or HARD drive?

    Hello!

    I am considering buying a Portege R830. I've yet to decide between the Portégé R830-10R (model with HARD drive) and the Portégé R830 - 10 p (model with a 256 GB SSD). To do this, I would like to know:

    -What is the SSD model assembled in the Portégé R830?
    -It uses a standard SATA connection or an owner like the previous Portégé R700 SSD?
    -Have someone replaced the original HDD to the Portégé R830 by a whole new SATA 3 SSD? Wich one? It works fine?

    Thanks in advance for your help.

    Hi MadVet,

    The SSD of Portege R830 - 10 p is a model of Toshiba 2.5 so it does not work in Portege R830. In addition due to the 2.5 form factor it uses SATA standard interface as normal hard drives.

    In my opinion, you should take the model with SSD. 256 GB is enough for the operating system and applications as well as for some important data. If you need more disk external HARD disk space use. SSDS are very fast and you will see the performance of the SSD HARD drive instead ;)

  • my audio syestem of beats went when I choose windows 8, how can I return it with the full version?

    my audio syestem of beats went when I choose windows 8, how can I return it with the full version? I have hp pavilion dv4 5110tx

    Hello

    Try the following.

    Download IDT Audio Installer on the link below and save it in your downloads folder.

    http://ftp.HP.com/pub/SoftPaq/sp59501-60000/sp59882.exe

    One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

    Then, download and reinstall the Chipset driver on the following link.

    Chipset Driver - Windows 8.

    After reinstalling, restart the laptop and let Windows load completely.  Open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  When this has completed, restart the computer again before checking if the Beats Audio is now listed in the windows control panel.

    Kind regards

    DP - K

  • Is there a camera without a mirror Canon with a full frame, GPS and WiFi sensor?

    Is there a camera without a mirror Canon with a full frame, GPS and WiFi sensor?

    kenka433 wrote:

    Is there a camera without a mirror Canon with a full frame, GPS and WiFi sensor?

    Canon 6 d has a full frame, GPS and WiFi sensor and can be opertated in LiveView mode mirrorless.

  • MX200 (TC6.2) cannot save with SIP TLS for control of VCS

    Hi all

    I just got a brand-new MX200 in our laboratories.

    We will evaluate at the moment the overall upgrade to the version sw TC6.2.

    The MX200 was delivered with TC6.1.1.7. Check in the control of VCS with SIP TLS works without any problem at all.

    VCS - C eventlog:

    "26 aout 14:16: 47 tvcs: event ="Accepted for registration"Service ="SIP"Src - ip ="172.18.93.88"Src-port ="5061"Protocol ="TLS"AOR ="[email protected] / * /"Contact =" sip:[email protected]/ * /: 5061; transport\ = tls"duration ="60"Level = '1' elements UTCTime = '2013-08-26 14:16:47, 833'

    "26 aout 14:16: 47 tvcs: event ="The requested record"Service ="SIP"Src - ip ="172.18.93.88"Src-port ="5061"Protocol ="TLS"AOR ="[email protected] / * /"Contact =" sip:[email protected]/ * /: 5061; transport\ = tls"duration ="60"Level = '1' elements UTCTime = '2013-08-26 14:16:47, 831'

    After registration TC6.2 update fails.

    The 26 aout 14:36: 26 tvcs: event = "Rejected registration" reason = "Received no authenticated source" Service = "SIP" Src - ip = "172.18.93.88" Src-port = "36545" Protocol = "TLS" AOR = "sip:DOMAIN.com" Contact ="<>[email protected]"/ * /: 5061;transport\=tls>;+sip.instance\= '"" duration = '3600' level = '1' elements UTCTime = "2013-08-26 14:36:26, 481"

    26 aout 14:36: 26 tvcs: event = "The requested record" Service = "SIP" Src - ip = "172.18.93.88" Src-port = "36545" Protocol = "TLS" AOR = "sip:DOMAIN.com" Contact ="<>[email protected]"/ * /: 5061;transport\=tls>;+sip.instance\= '"" duration = '3600' level = '1' elements UTCTime = "2013-08-26 14:36:26, 481"

    As far as I can see there's something doesn't quite work with the protocoll in relationship with the SIP URI (AOR). Miss me the prefix "[email protected] / * /"

    All other systems (profile, ex, sx) work properly with TC6.2.

    Anyone have an idea?

    Hi adil,.

    Since the inscription "AOR" is only said AOR = "sip:DOMAIN.com"

    I belive you must have some sort of rule research on the VCS the sip domain and pointing to the crossing or a nearby area and the policy setting must be "audit powers.

    and since there is no name of user and password available the record attempts will fail with the message "from source" unauthenticated

    did you recently create transformations on the VCS? also, check your configuration of endpoint.

    You can create a rule to send this registration through local area message passing in turn to the subzone to registration. Please note the subfield must be set on "treat as authenticated" If you do not use authentication.

    Rgds

    Alok

  • Problems with SIP scheduling TMS &gt; TP server

    I have a problem of planning where the TMS seems to say my TP server to dial a number to the preconfigured endpoints rooms/external to H323, despite endpoints being configured only with a SIP URI and no ID of H323.

    My external termination points are added as 'rooms' to TMS.  They 'allow reservations' and ' allow incoming SIP URI configured dialing, but all the other slots to be unchecked. "  They have no ID H323, E164, or configured firewall (gatekeeper is set to "off".

    When I have distributed them in a conference, connection settings developed as 'SIP-H323"instead of just"SIP", so he tries H323 numbering first.  It is a problem because many of these external endpoints are CTS-3000 units and if composed as H323, TIP does not work they only connect with a single screen.

    If I manually dial the SIP from the server TP, or if I add an external endpoint to the Conference through TMS and specify SIP, it works very well. It is only a matter because TMS seems to want the MCU try H323 first, despite the configuration 'House' with no option availible H323.

    It just came out recently is because we use TP Server 2.2 in conjunction with the CUBE and manually add endpoints to TP server as "legacy" systems of CTS.  We're heading TP Server 3.0 + VCS - E where TRICK works automatically, but it doesn't seem to work if the call is interoperability of H323, SIP.

    Any ideas how to get MSDS to compose rooms as SIP only (or at least first try SIP)?

    Versions:

    3.0 (2.48) Server TP

    TMS 14.2.2

    VCS 7.2

    Hi Nick,

    I had the same problem with TMS 14.2.2. I have fixed only after you have configured the 'Active SIP server address' field in the configuration page / equipment of the room. You can put any IP address in this field, any.

    It seems that TMS sets TP server to call using SIP only when this field is set to the configuration / the equipment in the room, if I leave this field blank, the result will be the same problem that you are experiencing, a configuration of the connection with H323--> SIP.

    Just to repeat, these are the areas that I have configured in hardware Configuration room to have work with SIP only:

    SIP mode: on

    Active SIP server address: 10.10.10.10

    SIP URI: [email protected] / * /

    Gatekeeper discovery: Off

    Allow the reservation: check

    Allow incoming SIP URI numbering: check

    IP maximum bandwidth: 6000

    You also need to set "Maximum bandwidth IP" field. If this field is '0', you will get an error message "no possible route between participants: TPserver and participating: tests.

    I hope this helps.

    Concerning

    Paulo Souza

    Please note the answers and mark it as "answered" as appropriate.

  • Model with overlapping of images to print custom

    I am trying to create a model of impression for (2) 5 x 7 postcards (with logo/contact info at the bottom) a 8.5 x 11 pages. I imported a white background Photoshop image of 5 x 7 with the contact information on the bottom. Now, I want to add 2 boxes of image on top of the work of 5 x 7. The areas of the image must be modifiable so that different images can be presented for different shipments. I would also like to be able to do all this in Lightroom. Can anyone offer advice on whether this is possible and if so, how?

    Everything in the Lightroom print module-

    Try starting with a model of Lightroom [Custom square + 2] or design your own in the Panel layout Style [Custom Package].

    Cells can be resized, repositioned, with overlap, moved behind / in front, striped and with an identity edited graphic plate border.

    Once you have your design as you want TI - save it as a print template, then you can drag and drop images in the cells at any time in the future - just select your images on the film, select your registered design and images in the cells, print (or save it as jpg for printing outside!)

    My impression model with 3 images & identity plate

  • How to create a seller on ebay model with muse adobe?

    Dear Helpers,

    I am a new seller on ebay (not seller of Web sites) and new user Adobe Muse, I love muse because it is easy to learn and quick to use.

    I need to create HTML templates for my listing new items on ebay like this: games. Workstation i7 GTX 5820 K - 32 GB-7 TB - 2 GB 670 - win 10 Pro desktop PC | eBay

    Screen Shot 2016-02-11 at 21.22.19.png

    Part of its HTML Code:

    Screen Shot 2016-02-11 at 21.26.11.png


    I tried to create a model with muse and I exported as HTML and I thought it's easy and only I need to go to index.html and copy the code in my ebay. but the problem was the empty index.html file as the picture:

    Screen Shot 2016-02-11 at 21.35.31.png

    then I got my browser as the picture code but it "didn't work on ebay:"

    Screen Shot 2016-02-11 at 21.37.04.png

    I read that eBay need a HTML code that include the code CSS as well as the HTML code.

    Can I do this with Adobe Muse?

    Thank you for your time and excuse my bad language.

    Best regards

    No, you can't. Muse is not intended for this kind of html and Muse also does not create email templates either.

  • I have pages of models with the general title and keywords. Can I still add title and keywords specific to each page?

    I have pages of models with the general title and keywords. Can I still add title and keywords specific to each page?

    The individual pages have editable regions. WithiIn these regions you can modify the document, but you want.

  • I paid for a year with the full creative cloud but can't find p´the program to download

    I paid for a year with the full creative cloud but couldn't findthe program to download

    To start https://helpx.adobe.com/creative-cloud.html the Cloud

    -Installation, update or uninstall and launching after installation

  • My mobile version of lightroom 30-day trial has expired, but I have Adobe Creative cloud with a full membership. How can I use lightroom for mobile in the future?

    My mobile version of lightroom 30-day trial has expired, but I have Adobe Creative cloud with a full membership. How can I use creative photography cloud adobe?

    Hello

    Please see: -.

    The use of Lightroom Mobile is included with Creative Cloud Student and Teacher Edition?

    Or

    Mobile Lightroom not available for education memberships | Kivuto

    You can also refer to the document:-Adobe Lightroom for mobile FAQ

    I hope that answers your query!

  • Just upgraded to Mac OS 10.11 and may not reduce the size of the document. A size of message says I don't have permissions. I think it has to do with SIP, but how this problem is corrected?

    Just upgraded to Mac OS 10.11 and cannot reduce a document. A message from Acrobat Pro says that I don't have permissions. I think it has to do with SIP, but how this problem is corrected?

    Zapped the PRAM and Acrobat Pro works now.

    ===================================

  • What script to create a model with a user interface panel

    Hello guys,.

    So I am new to scripting and javascript and I'm trying to keep it simple. I'm a VJ and want to create a script where I get a 'BPM' and a 'beat' lengh and it generate me a comp with the right length and * a layer with a marker ofr each beat.

    I was able to create this script, but I try to make it look a little better with integration of the user interface for AE I wasn't able to make it work right. If anyone can help me or give me some advice. I think that I'm not good with the expression "addComp" in the buildUI function.

    I copy everythin because it is long but you'll be understaind the main idea. My question is how to that the entry in my Advanced UI instead of "the guest".

    Here is my first code that does the job:

    Elements Var Set

    var name = prompt ("membership name");

    var BPM = prompt ("your BPM");

    If (isNaN (BPM)) {}

    Alert ("you must give the model a value");

    }

    Var prompt = beats ("how many times");

    If (isNaN (Beats)) {}

    Alert ("you must give the model a value");

    }

    frameRate var = prompt ("your fps");

    If (isNaN (frameRate)) {}

    Alert ("you must give the model a value");

    }

    term var = (60 / BPM * bat); Automatically generated

    var beat = (60 / BPM);

    Part of creation

    app.project.items.addComp (name, 1920, 1080, 1, duration, frameRate); Create the model with custom Lengh

    App.Project.Item (01).layers.addSolid ([0,0,0], "BG", 1920, 1080, 1, length); Create solid BG

    var firstLayer = app.project.item (1) .layer (1);

    firstLayer.label = 16;

    App.Project.Item (01).layers.addSolid ([0,0,0], "FX", 1920, 1080, 1, length); Create sound FX

    App.Project.Item (01).layers.addNull (Duration); Create the Null object

    var firstLayer = app.project.item (1) .layer (1); Rename the Null object

    firstLayer.enabled = false;

    firstLayer.name = "Beats";

    firstLayer.label = 0;

    Place a marker on the 64 first beat

    var myMarker = new MarkerValue("0");

    firstLayer.property("Marker").setValueAtTime (beat * 0, myMarker);

    Every beat on opacity-keys

    myProperty = firstLayer.opacity;

    myProperty.setValueAtTime (beat * 0, 0);


    For reference, I'm going to place code Dan here and use line numbers, as I explained.

    Fig. A

    var name = prompt("Composition name");
    var BPM =prompt("Your BPM");
    if (isNaN(BPM)) {
        alert("You must give the comp a value");
      }
    
    var Beats = prompt("How Many Beat");
    if (isNaN(Beats)) {
        alert("You must give the comp a value");
        }
    
    var frameRate = prompt("Your fps");
    if (isNaN(frameRate)) {
        alert("You must give the comp a value");
        }
    
    var duration = ( 60  / BPM * Beats ); //Auto Generated
    var beat = (60  / BPM);
    //Creation Part
    var myComp = app.project.items.addComp(name, 1920, 1080, 1, duration, frameRate); // Create Comp with Custom Lengh
    var firstLayer = myComp.layers.addSolid([0,0,0], "BG", 1920, 1080, 1, duration); // Create BG Solid
    firstLayer.label = 16;
    myComp.layers.addSolid([0,0,0], "FX", 1920, 1080, 1, duration); // Create FX Solid
    firstLayer = myComp.layers.addNull(duration); // Create Null Object
    firstLayer.enabled = false;
    firstLayer.name = "Beats";
    firstLayer.label = 0;
    // Place a marker on the 64 first beat
    var myMarker = new MarkerValue("0");
    firstLayer.property("Marker").setValueAtTime(beat*0, myMarker);
    // Key every Beat on opacity
    var myProperty = firstLayer.opacity;
    myProperty.setValueAtTime(beat*0, 0);
    

    OK, so for your configuration, looks like you're striking four data sets. You have the model name (fig.) At line 1), BPM (lines 2-5 of Fig. (A), (lines 7-10 of Fig. rhythms (A) and the FPS (lines 12 to 15 of Fig. (A). then it comes to the UI, you can change what I had posted to...

    res = "group{orientation:'column', alignment:['fill', 'fill'], alignChildren:['fill', 'fill'],\
      myCompName: EditText{text:'Enter comp name'},\
      myBPM: EditText{text:'Enter BPM'},\
      myBeats: EditText{text:'Enter beats'},\
      myFPS: DropDownList{properties:{items:['23.976', '24', '29.97', '30', '59.97', '60']}},\
      createComp: Button{text:'Create comp'},\
    }"
    

    This will give you all entries in four data for the user interface. It is preferable to assign each control to a new variable for use in your script.

    // Control Variables
      var compName = myPanel.grp.myCompName;
      var myBPM = myPanel.grp.myBPM;
      var myBeats = myPanel.grp.myBeats;
      var fps = myPanel.grp.myFPS;
      var createComp = myPanel.grp.createComp;
    

    Once you have these variables you can then start the default implementation as appropriate. in this case, the drop-down list should be a starting point for it's selection, so that you can say to use the first default entry as follows.

    //Defaults
      fps.selection = 0;
    

    Now, you can configure your onClick for button createComp feature. This will contain to working part of the Dan code that treats everything (lines 17-33 of Fig. (A). I've added a few lines of options above this (lines B Fig. 1-7) in the below code just to match the variable names so you wouldn't need to change the code.

    Fig. B

    //onClick setups
      createComp.onClick = function(){
      //Gather user entered values
      var name = compName.text;
      var BPM = Number(myBPM.text);
      var Beats = Number(myBeats.text);
      var frameRate = fps.selection.text;
    
      var duration = ( 60  / BPM * Beats );
      var beat = (60  / BPM);
      //Creation Part
      var myComp = app.project.items.addComp(name, 1920, 1080, 1, duration, frameRate);
      var firstLayer = myComp.layers.addSolid([0,0,0], "BG", 1920, 1080, 1, duration);
      firstLayer.label = 16;
      myComp.layers.addSolid([0,0,0], "FX", 1920, 1080, 1, duration);
      firstLayer = myComp.layers.addNull(duration);
      firstLayer.enabled = false;
      firstLayer.name = "Beats";
      firstLayer.label = 0;
      // Place a marker on the 64 first beat
      var myMarker = new MarkerValue("0");
      firstLayer.property("Marker").setValueAtTime(beat*0, myMarker);
      // Key every Beat on opacity
      var myProperty = firstLayer.opacity;
      myProperty.setValueAtTime(beat*0, 0);
      }
    

    Then line 2 Fig. b starts the call onClick for button and assigns a function. Within the function, we run the process. Fig. B Line 4 seizes the compName edit text attribute of the text control, using the Number() function convert us this text to a number for use online B Fig. 9 and 10 and B Fig. 5 line gets the text attribute of the text control edit BPM. Goes same for line 6 of the Fig. B and the beats variable. For line B Fig. 7, a drop-down list requires calling his selection of the attribute, then it is text attribute to get the actual string. The drop was more logical for FPS due to the standard rates that exist. This list can be changed of course to your liking. Now, there is no safety net as I like to call for the modification of the text controls to make sure text is not entered when you need a number and vice versa. It would be something of can check after line 7, Fig. B before trying to run the code in process (Fig. B lines 9-25). I hope that it will be easy enough for you to understand.

    If the script is as follows.

    {
    function myScript(thisObj) {
      function myScript_buildUI(thisObj) {
      var myPanel = (thisObj instanceof Panel) ? thisObj : new Window("palette", "My Panel Name", [0, 0, 300, 300]);
    
      res="group{orientation:'column', alignment:['fill', 'fill'], alignChildren:['fill', 'fill'],\
      myCompName: EditText{text:'Enter comp name'},\
      myBPM: EditText{text:'Enter BPM'},\
      myBeats: EditText{text:'Enter beats'},\
      myFPS: DropDownList{properties:{items:['23.976', '24', '29.97', '30', '59.97', '60']}},\
      createComp: Button{text:'Create comp'},\
      }"
    
      //Add resource string to panel
      myPanel.grp = myPanel.add(res);
    
      // Control Variables
      var compName = myPanel.grp.myCompName;
      var myBPM = myPanel.grp.myBPM;
      var myBeats = myPanel.grp.myBeats;
      var fps = myPanel.grp.myFPS;
      var createComp = myPanel.grp.createComp;
    
      //Defaults
      fps.selection = 0;
    
      //onClick setups
      createComp.onClick = function(){
      //Gather user entered values
      var name = compName.text;
      var BPM = Number(myBPM.text);
      var Beats = Number(myBeats.text);
      var frameRate = fps.selection.text;
    
      var duration = ( 60  / BPM * Beats );
      var beat = (60  / BPM);
    
      //Creation Part
      var myComp = app.project.items.addComp(name, 1920, 1080, 1, duration, frameRate);
      var firstLayer = myComp.layers.addSolid([0,0,0], "BG", 1920, 1080, 1, duration);
      firstLayer.label = 16;
      myComp.layers.addSolid([0,0,0], "FX", 1920, 1080, 1, duration);
      firstLayer = myComp.layers.addNull(duration);
      firstLayer.enabled = false;
      firstLayer.name = "Beats";
      firstLayer.label = 0;
    
      // Place a marker on the 64 first beat
      var myMarker = new MarkerValue("0");
      firstLayer.property("Marker").setValueAtTime(beat*0, myMarker);
      // Key every Beat on opacity
      var myProperty = firstLayer.opacity;
      myProperty.setValueAtTime(beat*0, 0);
      }
    
      //Setup panel sizing and make panel resizable
      myPanel.layout.layout(true);
      myPanel.grp.minimumSize = myPanel.grp.size;
      myPanel.layout.resize();
      myPanel.onResizing = myPanel.onResize = function () {this.layout.resize();}
    
      return myPanel;
      }
    
      var myScriptPal = myScript_buildUI(thisObj);
    
      if ((myScriptPal != null) && (myScriptPal instanceof Window)) {
      myScriptPal.center();
      myScriptPal.show();
      }
      }
    
      myScript(this);
    }
    

Maybe you are looking for