Cypher v2 and weak SSL

I have a rsv4000 updated to firmware v2.0.3.4 when remote access is enabled and an analysis of PCI compliance is made accepts monograms low years sslv2, which are considered at high risk for safety. Any thoughts on how to solve this problem and still allow remote access.

Currently, you agree the following less than 128-bit encryption and Protocol SSLv2. Please disable acceptance of ciphers below 128 bits and disable acceptance of the SSLv2 protocol.

Cipher (s) of server support:

Accepted SSLv2 168 bit DES-CBC3-MD5

Accepted SSLv2 128 bit IDEA-CBC-MD5

Accepted SSLv2 128 bits RC2-CBC-MD5

Accepted SSLv2 128 bit RC4 - MD5

Accepted SSLv2 56 bit DES-CBC-MD5

Accepted SSLv2 40 bits EXP-RC2-CBC-MD5

Accepted SSLv2 40 bits EXP-RC4-MD5

Accepted SSLv3 56 bit DES-CBC-SHA

Accepted TLSv1 56 bit DES-CBC-SHA

Cipher (s) of preferred server:

SSLv2 168 bit DES-CBC3-MD5

256-bit AES 256 - SHA SSLv3

TLSv1 256 bit AES 256 - SHA

SSL certificate:

Version: 3

Serial number :-0

Signature algorithm: sha1WithRSAEncryption

Issuer: / CN = Linksys_RVS4000/OR = RVS4000/O = Cisco Systems, Inc./C = US

Not valid before: 22 Nov 17:03:18 GMT 2011

Not valid after: 19 Nov 17:03:18 GMT 2021

Subject: / CN = Linksys_RVS4000/OR = RVS4000/O = Cisco Systems, Inc./C = US

Public key algorithm: rsaEncryption

Thank you

Dave

Advertisement

Same problem with RV320.

Tags: Cisco Support

Similar Questions

  • Cisco ASA 5505 and comodo SSL certificate

    Hey all,.

    I'm having a problem with setting up the piece of Certificate SSL of Cisco AnyConnect VPN. I bought the certificate and installed it via the ASDM under Configuration > VPN remote access > Certificate Management > identity certificates. I also placed the piece of 2 CA under the CA certificates. I have http redirect to https and under my browser, it is green.

    Once the AnyConnect client installs and automatically connect I get no error or anything. The minute I disconnect and try to reconnect again, I get the "VPN Server untrusted certificates! ' which is not true because the connection information to be https://vpn.mydomain.com and the SSL certificate is configured as vpn.mydomain.com.

    On that note, it lists the IP address instead of the vpn.mydomain.com as the unreliable piece of this. Now of course I don't have the IP as part of the SSL-cert, just the web address. On the side of the web, I have a record A Setup to go from vpn.mydomain.com to the IP address of the Cisco ASA.

    What I'm missing here? I can post config if anyone needs.

    (My Version of the Software ASA is 9.0 (2) and ASDM Version 7.1 (2))

    Yes that's correct. technically, it will take you to EKU as keys to authenticate server who was a little forced in version 3.1. But eventually, he was taken away. If you get no error using the browser and ot only comes with the anyconnect client. Most likely, you do not have to configured values. I can confirm that if you can share the fqdn with me also, you can try the upgrade and check it out.

    Thank you

    Bad Boy

  • How to disable SSL 2.0 and use SSL 3.0 or TLS 1.0 instead.

    We want to disable SSL 2.0 and use SSL 3.0 or TLS 1.0 instead. We used the followign command:

    SET JAVA_OPTION = - Dweblogic.security.SSL.protocolVersion = SSL3 - Dweblogic.security.disableNullCipher = true

    but still SSL 2.0 is used. Help, please

    Deepak looking good so far.

    Let us know for any other help. We encourage you to create a service request with Oracle.

    See you soon,.

  • differnce between Ref Cursor strong and weak Ref Cursor

    differnce between Ref Cursor strong and weak Ref Cursor

    SQL and PL/SQL FAQ

    -------------
    Sybrand Bakker
    Senior Oracle DBA

  • vWorkspace and vulnerability SSL POODLE

    In order to mitigate the vulnerability of POODLE on my secure gateway server, I tried to disable SSL 3.0. TLS 1.0, 1.1, and 1.2 are enabled.

    I can connect is no longer on. The web proxy works and shows the applications, but when I try to start an application it fails. Enable SSL 3.0 back allows me to log on.

    Scott.

    Hello

    Kevin Robinson here the support Manager, Yes please install this hotfix required to solve the problem you have.

    Let us know if this solves your problem.

    Thank you

    Kevin

  • Help with Aironet 1252AG-E-K9 and weak signals

    Hello

    I have an AIR-AP1252AG-A-K9 and a LOOK - ANT2506 2.4 GHz omnidirectional antenna. First of all, I am new to wireless space...

    I have to connect to a local network with a PC which is 280 meters, only a single PC. We have the Aironet connected to the switch with this antenna, but the signal is very weak, I am doing wrong? or what I need to do?

    I activated the SSID and Radio0 - 802.11n2.4 GHz, give the IP address and I can connect my laptop... but the signal is so weak and we need to get the signal to 280 meters!  ;-(

    Thanks in advance...

    195 m is too much for any client.

    It must come with an access on each side point and powerful antennas. That's all.

    Nicolas

    ===

    Remember responses of the rate that you find useful

  • Cisco ACS 5.1 and ASA SSL VPN change or notify the expired password

    Hello

    Now, my ACS and ASA related to RADIUS (MSCHAPv2). I've set up password life on GBA and password management on SAA. But Cisco ASA did prompt change or whatever it is to notify when the user tries to log on with Clientless SSL VPN. Could you advice me everything to change, or notify the expired password?

    PS.

    I check change password on the first login of th on ACS this confirmation of the ASA to change password dialog box. But I want change or warn when the expired password

    Thank you

    The default password is marked as disabled after expiry

    I think that there is an improvement for this in the 5.2.0.26.2 patch and above, which includes the following:

    CSCtk32168: Add an option to change the password when the password expires (T + and Radius)

    After you install this hotfix, you get an option to the user authentication settings is:

    -Disable the user account

    -Expire the password

    When the expiration period is exceeded

    If password is expired then user will be asked to change password next authentication

    Note this latest patch for 5.2 is 5.2.0.26.4. All patches are cumulative

  • ACL and anyconnect ssl vpn

    Hello world

    I was testing the few things at my lab at home.

    PC - running ssl vpn - sw - router - ISP - ASA (anyconnect ssl)

    AnyConnect ssl works very well and I am also able to access the internet.

    I use full tunnel

    I have ACLs on the external interface of the ASA

    1 True any     any   intellectual property Deny 0 By default   []

    I know that the ACL is used to traffic passing by ASA.

    I need to understand the flow of traffic for internet via ssl vpn access. ?

    Concerning

    MAhesh

    As you correctly say, the ACL interface is not important for that because the VPN traffic is not inspected by the ACL. Of the at least not by default.

    You can control the traffic with a different ACL that is applied to the group policy with the command "vpn-filter". And of course you need a NAT rule that translates your traffic when running to the internet. This rule should work on the pair of interface (outside, outside).

  • PHP Curl and check ssl

    Hi all

    I'm trying to build a php class to be able to use workflows in Orchestrator.

    I can use a lot of applications, using this code:

    $curl = function curl_init();

    $url = $this-> url. "Catalog/System/Workflow /';

    $curlOptions = array)

    CURLOPT_URL = > $url,

    CURLOPT_CUSTOMREQUEST = > 'GET ',.

    Curlopt_buffersize = > CURLAUTH_BASIC,.

    CURLOPT_SSLVERSION = > 3,

    CURLOPT_SSL_VERIFYPEER = > 0,

    CURLOPT_SSL_VERIFYHOST = > 0,

    CURLOPT_USERPWD = > ' $this-> username: $this-> password. "

    CURLOPT_RETURNTRANSFER = > true,

    CURLOPT_HEADER = > true

    );

    curl_setopt_array ($curl, $curlOptions + $this-> curlOptDefaults);

    $content = curl_exec ($curl);

    If (curl_errno ($curl)! = 0)

    {

    echo ' CURL error: ".". " curl_error ($curl);

    Die (»);

    }

    $tabWorkFlows = json_decode ($content, true);

    But when I add this header

    CURLOPT_HTTPHEADER = > ' Content-Type: application/xml '

    I still have the question:

    SSL certificate problem, verify that the CA cert is OK. Details: error routines: 14090086:SSL: SSL3_GET_SERVER_CERTIFICATE:certificate check failed

    even if I leave ssl_verifypeer and verifyhost of ssl to 0. Have someone to experience this problem?

    Feel free to ask more if necessary.

    Hello

    may be a problem that CURLOPT_HTTPHEADER expects an array.

    Tim

  • Known issues with VMWare Fusion 2.0.2 and FTP/SSL?

    Hello

    I have a virtual machine in VMWare Fusion 2.0.2 running Windows XP with SP3. I have the Windows Firewall and AVG Free running.

    I use FileZilla as my FTP client. I am able to connect to a server using the vanilla FTP protocol. No problems.

    However, when I try to use FTP/SSL to connect to a server, I get time-out errors as it gets stuck on "initializing TLS... ».

    I tried to disable the Firewall and AVG. Nothing helps.

    I tried other FTP clients (CuteFTP, for example). Same result.

    And, I am able to connect through FTP/SSL and FileZilla to my host (Mac OS 10.5.6) operating system and another computer in my house running Windows 7.

    So I narrowed down it to something in this specific virtual Windows machine installation, but I don't know what else to try.

    Any suggestions?

    Thank you.

    How is the Machine to stop virtual network set up, NAT or bridged?  If NAT have you tried to use bridged?  Note: If you change from NAT to Bridged while the Virtual Machine is running, the IP address must be released or renewed.  If you are unsure how to do this then just restart the Virtual Machine.

  • Need the difference between strong Ref Cursor and weak Ref Cursor examples

    Oracle 9.2

    It would be great if someone can help understand the differences between
    1 Strong Ref Cursors(return type)
    and
    2. weak Ref Cursor (no return type)

    What I read is weak ref Cursor as sys_refcursor is better to use the ref Cursor, because in the case of slider strong Ref object type that will be returned must be declared in advance. It dosent make sense to me?

    I start with the examples would be appreciate for advice

    Strong Ref Cursor

    create the package str_pack
    is
    type sref_type is ref cursor return emp % rowtype;
    SVAR sref_type;
    end str_pack;

    Create procedure st_proc (eid in number, c1 on str_pack.sref_type)
    is
    Start
    Open c1 to select empno, ename, sal from emp where empno = eid;
    end;

    declare
    str_pack.sref_type C1;
    type rec is RECORD (eid, ename varchar2 number (20), number of sal);
    SheikYerbouti rec;
    Start
    st_proc(10,C1);
    loop
    When exit c1% notfound;
    Fetch c1 into SheikYerbouti.
    end loop;
    Close c1;
    end;


    There could be errors in the above example but its basically to get a better understanding.

    For weak Ref Cursor

    procedure of the child

    Create procedure child_proc (in number, c1 on sys_refcursor eid)
    is
    Start
    Open c1 to select empno, ename, sal from emp where empno = eid;
    end;

    parent process

    Create procedure parent_proc (recnum varchar2)
    is
    p_retcur sys_refcursor;
    emp_row emp % rowtype;
    Start
    child_proc (eid, p_retcur);
    loop
    extract the p_retcur in emp_row;
    dbms_output.put_line(emp_row.empno ||) e '|| emp_row. Ename | "wins". emp_row. SAL);
    end loop;
    end parent_proc;

    Concerning
    @

    Hello

    the fundamental difference is to do with the compiling and linking of runtime type that occurs.

    The he should explain a lot more detail than I could ever!
    http://asktom.Oracle.com/pls/asktom/f?p=100:11:0:P11_QUESTION_ID:1640161160708

    P;

  • I use hp eprint and that you can not set the e-mail account. Should what settings I use for the Description, host name, Port and use SSL?

    I downloaded hp eprint app and you cannot configure e-mail account

    I suggest you ask on a forum of HP. It's nothing to do with Thunderbird, as the eprint software connects directly to your email provider that I see.

    Maybe this will help http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile-Printing-and-ePrintCenter/Cant-find-my-computer-eprint-email-address/td-p/680697.

  • Satellite C55-C5241 - 10 Windows slow and weak WiFI signal

    Hello

    I bought this laptop about a month ago, and the mention of the above problem came from the box.
    the signal is very low, even when the laptop is close to the router.
    the router have no problem.
    I've updated all the drivers broadcom 802.11n, realtek and intel LAN driver.
    Nothing helps!
    its really annoying to get the laptop like this new in box of...

    Posted by tomerrr
    Hello

    I bought this laptop about a month ago, and the mention of the above problem came from the box.
    the signal is very low, even when the laptop is close to the router.
    the router have no problem.
    I've updated all the drivers broadcom 802.11n, realtek and intel LAN driver.
    Nothing helps!
    its really annoying to get the laptop like this new in box of...

    I wanted to ask you if you have a solution because I have the same problem with my C70-B-212
    In the same place that my laptop, I have no problem WiFi with my apple tablet.
    My dealer Toshiba says that it is a problem of W10...

    Thanks in advance!
    FT

  • external hard drive move... help me I am old and weak

    I bought the new iMac, huge screen... xcant waiting.  in any case, all the files migrated from old macbook to the new iMac. Images of presets etc. ext HD... LR does not see HD says I don't have any pictures. Hehe SUSPECT IT IS A MYSTERY BUTTON SOMEWHERE  help me to reconnect.  you want to use new computer!  waaaaaa

    You transfer the catalog to the new computer file and then open it?

    If so, please read this document:

    Adobe Lightroom - find moved or missing folders and files

    If this isn't the case, then it's what you need to do. More details: How can I move Lightroom to a new computer? Lightroom Queen

  • AnyConnect Mobile and Premium SSL free licenses

    Hello

    I currently have a pair of ASA5510 HA, if I understand the 2 free premium licenses can be used by the mobile client, as long as the ASA has the license for mobile clients?

    Can someone confirm that my interpretation is correct, or I have to buy a separate license to the premium one long with the license mobile client to enable this feature?

    Thanks for your time.

    Hello

    That's right! I did the same action on an ASA5505. In this case, you only need the anyconnect mobile license.

    Please mark answered for useful messages.

Maybe you are looking for

  • Getting a shared list of variable references

    I'm working on a project of data acquisition that will use AES. This is really my first foray in EVS, and I hit a stumbling block. I'll use a loop for distributing the waveforms acquired at their appropriate variables (DAQmx read Nsamples, Nchannels,

  • Only background noise

    When playing on a movie, it is only the background noise there is dialogue very little or nothing at all It seems that surround rear speakers only Running Windows 7 64-bit SP1 Already checked Device Manager driver is up to date What else can I check?

  • uninstall the KB955759 and KB972270 security updates in xp

    automatic updates from 19/01/10 made my almost powerless browsers especially firefox. These two [955759 KB and KB972270] security updates have been installed in the afternoon, and I have since been in pc _. I can't do a restore.Is there a method to c

  • Volume under license of Windows 7 Enterprise Edition new install hangs at disk.sys

    Original title: installation of new Windows 7 hangs at disk.sys We have conducted our mail, ftp and video servers on XP because we expected a software upgrade for our video server, so that we can install Windows 7. The MB is a Gigabyte GA-H55M-UD2H R

  • Unable to video file to the SD card by using the data source and SourceStream stream

    I see this in the debug output: SMPones acquired session id = 1799MN: init0 (0) = 0MN: charge 0MN: seekComplete0 (0) = 0MN: seekComplete0 (0) = 0AUDIOMANAGER: IOExceptionMN: unload0 (0) = 2 pauseHandle = 7fffffffStreaming is reason = 1 prev - state =