Danaher drive blinking green light

I try to connect Vsio and Ciso on the UMI-7772.

Movement system includes a Danaher P70360 and motor NEMA 34 (N31HRLG-LEK).

The engine works well when the power is connected. When Viso and CISO are connected and that the motor is disconnected, the Viso LED and V are green and everything seems in good condition.

However when I connect the engine on axis 1 or 2, turn it off and this axis fault led lights up.  The drive motor begins to blink green.  I can't get the engine to run at all in this State.

Anyone have any ideas?

Thank you

Sean

Hi Imitiaz,

Thnaks for the suggestions.

The system works now, I don't really know why.  It started working after that switch was toggled on the UMI-7772.  It could be one of the following solutions:

1 something was stuck inside and activating / deactivating switches enabled him to become unstuck.  This happens with mechanical relay, but I don't think that the relays are mechanical.

2. I can recreate the fail affecting end active low Max.  This is in contradiction with the UMI-7772 settings and software actually replaces the UMI.  So even if there is no visible LED on the UMI-7772 they are on in the software and work around them.  I think it is probably the cause of the problem.

Tags: NI Hardware

Similar Questions

  • After turning on my wireless keyboard led green lights, then begins to blink, and then turns off. The batteries are fresh.

    After turning on my wireless keyboard led green lights, then begins to blink, and then turns off. The batteries are fresh.

    Possible explanation.  It is likely that batteries, so fresh, can be irregular in size.   The uncertain connection would therefore tend to lead to a failure to blink and you declare.   Read my thing...

    Batteries.

  • FaceTime Camera: the green light next to the camera makes a slow blink, and there is no picture

    MacBook (retina, 12 inch, early 2015) El Capitan 10.11.5 now ongoing enforcement.

    Whenever I try to access the camera FaceTime (FaceTime, Photo Booth Apps) the green light next to the camera made a slow blink, and there is no picture.

    The system report > camera > model ID: Apple camera VendorID_0x106B ProductID_0x1570

    The numbers of the vendor and the product are correct?

    The camera worked for 6 months passed and I used FaceTime several times without problem.  Several users are affected.

    None of the recent changes to the system.

    Since the problem began, I have:

    (1) installed Skype to see if one application other than an Apple app had a camera problem. Skype has no camera or.

    (2) improved 10.10.4 to El Capitan Yosemite.  Hoping that the upgrade would reload the application Face Time.   No change in symptoms

    (3) reinstalled the El Capitan using the OS X Internet recovery.  I have not used the time Machine.

    (Note for everyone, it was simple and painless and does not need to reinstall applications.)  I want to reinstall MS OS was too simple)

    (4) several other threads suggested to reset NVRAM and SMC memory, even if they do not seem to be associated with the prob. who - without success here tried either

    Any advice to determine whether it is hardware or software?  Still dig while you wait for a response.

    Note: This problem is not resolved

    Also, over How to troubleshoot the iSight - Apple Support .  Any assistance to the problem.

  • LaserJet Professional P 1102w printer green light blinking, but will not be printed

    I had my P of professional LaserJet 1102w for a little less than a year.  I use it very rarely and very slightly (I've probably printed total less than 25 pages).  It has always worked well.

    But in the last 2 weeks, it stopped printing.  The Green led comes on, but it will not be printed.

    I went through the troubleshooting diagnostic tests on my computer (HP Pavilion, Windows 7 operating system).  The result shows that my computer detects a problem, but it cannot identify it (for example, no paper jam, no toner, etc..).  I manually checked it for a paper jam too.  I have not seen any problems.  I turned off, unplugged, he turned his back.  She still does not print.  And now the green light blinks, even if I turn it off several hours ago.

    Help, please.  Thank you.

    Update: I realized what it was.  My USB cable was very slightly loose.  I don't see when I checked manually the printer the first time.  But I checked a second time and just pushed him tighter.  Problem solved.

  • After several years of functioning, my Time Capsule shows a yellow flashing light instead of solid green light.  He always seems to be working, but watch the blinking light.  An update is necessary?

    Time Capsule.   After six years of good operation, my Time Capsule shows a yellow light flashing instead of green light solid.  It seems to work fine, and I tried l ' switch off and restart, nothing helps.  An update is necessary?

    The Capsule of time... and other Apple routers... flashing orange when they have a message for you. To see what it is...

    Open AirPort Utility on your Mac... (Finder > Applications > utilities > AirPort Utility)

    Click on the image of the Time Capsuleand a small window will appear

    If you see an Update button, then new firmware is available for the Capsule of time if you want to install this package. To do this, click on the Update button

    Otherwise, find the Status parameter and then click on the little orange dot it for more information on why the status light flashes, with a suggestion to fix whatever may be the cause

  • Sony Bravia KLV-40R452A. Green light keeps blinking and the Menu keeps popping up.

    Hi, I have a Sony Bravia KLV-40R452A. Green light on the model continues to Flash. The TV starts, but the Menu keeps popping up.

    I have reset to factory settings with the arrow upwards on the remote and turning the TV power on the back of the screen. It did not improve the issue. I changed the plug too, same result.

    PS - I keep seeing that support here just redirects questions from the Asia-Pacific region at their Web site. There is no community online in Asia-Pacific. Please try to resolve my problem here. At least try.

    Had a chat with Sony Online service. I am posting this here in case someone else has the same problem.

    If the menu entry keeps popping up, just press and hold the menu behind the LCD (not on remote) button for 10-15 seconds until a message arrives "demo mode: Off '.

    This solved my problem.

  • Dell XPS 420 not go, bright, flashing orange light orange on the motherboard, flashing green light behind USB on motherboard

    I am running Windows 7 on my XPS 420, I had updated the power supply two years back and installed extra ram and an SSD, a few months ago.

    I quit the PC last night, normally

    This morning, it is not booting, the light was blinking orange, including the connected mouse was blinking also.

    I decided to open it and check all connections; everything went well on the inside.  Before you open the PC, I unplugged all the extras connected like mouse, etc.

    The computer has actually started up normally and when I plugged the monitor it looked ordinary, he had reached the Windows login screen.

    HOWEVER, when I plugged the first rear USB component, the computer off and started to blink.

    I'm not sure what the problem is here.  My motherboard is fried?  I don't think it's the power supply from the computer DID resume after I noticed the blinking yellow light.  I wonder if the flashing of the earlier mouse and/or the flashing green on the back (inside the PC) of USB port average something else.

    Any advice is greatly appreciated

    AC360

    First check that all the cables for power and data are correctly connected, including the cables on the front panel.

    No difference and if you're comfortable working around computers, you can try the following:

    Note: The only 100% POWER supply test method, is to install a known working power.

    Unplug the power cord, hold the power button in for about 15-20 seconds, open the case, disconnect the power connector 24-pin motherboard and jumping the Green wire to one of the black wires, plug in the power cord and the power of the system, if the PSU, case fans and disk hard drive performance then the power supply can be good.

    Note: Do not remove the wires from the plug, use a small piece of wire or a paper clip as a rider.

    Extract supply and the system still does not work, yet once remove the power cord, hold button power in a few seconds to discharge residual power, reconnect the connector 24 pin to the motherboard.

    Remove any PCI video card [as appropriate], memory cards, all the devices, unplug data cables and power to all readers, check that the cable from the front panel is connected to the motherboard, without anything else connected to the system, reconnect the power cable and power the system on.

    If there is no difference in the diagnostic lights, of "Beep" codes and/or the indication of the LED on the power button, it would seem that the motherboard is dead and/or the processor and the only method I know to check a processor is perhaps install a compatible work PC, or use a known job processing.

    Bev.

  • Don't Dim green light no fix

    My 2012 Macbook Pro 13 inch lost its charge a week ago. The charger lights a green light. When I press the button on the side of the Mac to see the power, only the first green light blinks then turns off. The Mac does not load.  It took to pcworld and connected to one of their Chargers it bright green illuminated (should be orange) and still won't turn.

    I tried SMC

    Tried to remove the battery and put back

    Nothing works

    You might have against accidental damage to the logic or the Board of Directors of magsafe DC. You must bring it into an Apple store for troubleshooting.

    Here's an article on what charger you need for your model. I'll try to test a known good charger with your battery installed and started. What is your state of the battery when disconnected and plugged?

  • Green light is on after saving workout

    I noticed that when I did a workout using Apple training app, the green light remains on. However, using a third party bodybuilding training app, the sensor lights do not remain after the recording of the session as it does with Apple app. During this experience, I also see the green icon of the person currently running on the dial of the watch.

    I was able to get light and the icon turns off by opening a series of other applications on the watch, it usually takes about three other applications to load before the icon and the light turn off. I think that's what ends up completely close the app to drive for some reason any. It's a little awkward to do and if I can't, she empties the battery fairly quickly.

    I thought maybe with last update yesterday (2.2.1), I'd see a fix, but a test this morning revealed that there is a problem.

    I wonder if anyone else can be faced with this or similar or if anyone my knowledge a fix.

    Thank you

    Hello

    Check if an activity is currently suspended in a third-party application fitness on your watch (like the app of bodybuilding or any other application of fitness that you may have installed and already used).

    If there is, put an end to this activity within this app on your watch (not your iPhone).

  • Desktop won't start. flashing green light

    I have a 1318NX Compaq Presario SR which will not start!  There is a green light flashing on the back of the power supply; which is normally green 110V AC is plugged into it.  I tried the trick of the Start button while not plugging the power cord... no help.  I also opened the case and carefully got rid of any power cord of all internal devices... the light turns green only when I pull the main power of the motherboard!

    I need to replace the motherboard?  Troubleshooting on hp.com site would indicate that the power supply is OK if the light is solid green.

    Thanks for your suggestions,

    Lou

    My wife's computer had the same problem several times. A solution I found that worked before was to unplug the power cable from motherboard and the power supply cable to the back of the PC and then connect the power cable and plug the motherboard power cable while holding down the power button. Scary, to say the least, but it worked, until one day I accidentally spilled the bad circuit breaker and then spend two hours trying the same solution with no luck and the Google search again. And here's what I found. It is the simpler solution even more cruel. It is simple and noninvasive and no matter how tech savvy you are. Take a blow dryer and turn it on to blow air at the rear of the power supply for a few minutes. When you see the light turn green, you're ready. It's worked for me after that it worked for a hundred others, maybe more. A look at the testimonials on this site: http://talk19.wordpress.com/2008/01/13/hp-m7088d-power-supply-led-blinks-green/. It's a shame that nothing like that appears on any site of HP. So don't waste your money on a new MoBo or PSU. All you need is dry hair of your wife.

  • My airport express base station works but the yellow light flashes constantly how can I get the green light?

    Yellow light blinking on my airport express and I can not get the green light flashes. Internet still works well.

    When the amber light is flashing, open AirPort Utility

    • Click on the AirPort router
    • Look for the Status parameter in the small window that appears
    • Click on the little orange dot here and another window will open to explain what might be the 'question '.
  • Green light for the volume and shine

    Hello

    I have a T-61. I just discovered that the green light that appears down to the center of my moniter for volume and shine is gone. Could someone help me get the go-ahead on even once?

    Thank you

    reg08

    Are you talking about something like that?

    If so, I think that you will need the hotkey driver for your T61, available here:

    http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-68000

  • Reference Dell V313w green light flashing of power

    Howdy,

    I left this printer House my father to mine, and when I plugged the power button began to blink green. It worked very well with him and I drove just two blocks away, so I don't think anything being pushed around around.

    I have pressed the power button for a minute without change. I also unplugged the printer from the wall and disconnect the power to the printer. I waited a few minutes then reconnected power. I went through the manual and searched on the internet but came up with nothing useful. I tried to install the printer on my computer, but the installer think that the power is off to the printer.

    Thank you for any help or advice. The green light flashes constantly tormenting me. :)

    Hi Montanaw,

    There is no reset for this printer pin hole button. To reset the printer, please follow the mentioned below as follows:

    1. Turn the printer off.
    2. Press on and press and hold the 'Start' and 'Cancel' button and then press the "Power" button to turn on the printer.
    3. The printer resets and starts the initial printer installation.

    If the problem persists, the printer must be replaced.

  • Green light for blackBerry Smartphones keeps flashing

    Have a Curve 8330 with Sprint service.

    I tried several things to get the green light to stop blinking... remove the battery, remove the SD card, charging full, turned on/turned off/turned on, deleted messages, allowed out emails, etc..   Randomly, he stopped temporarily to Flash and then an hour later went immediately to Flash. At this thing for only 5 days now and ready to return!

    If you open the display options and keyboard under options, your LED is set for the signal coverage? If not, then try to remove the battery for a good 30 seconds

  • That means a green light flashing on iPod Shuffle 4th Gen?

    When you listen to songs on my iPod Shuffle 4th gen, the LED flashes green (connected to the helmet, not the USB port on the computer).  I thought it was supposed to stay green. What does a flashing green light?  Thank you.

    When you play the shuffle, the light usually indicates the level of battery charge.  Green , fresh strong (I think that more than 25%).  He goes to the orangeand then Red (reduced rate).  While playing songs, he should not stay ON or flashes continuously, unless you press the control buttons.

Maybe you are looking for

  • Satellite Pro A200 - new RAM work together

    Laptop Toshiba Satellite Pro A200-PSAF1A-003002, I bought the year last with RAM 2x512MB that I try to update my 3 GB RAM and I bought 2 RAM KTT667D2 / 1 G & KTT667D2 / 2G Kingston memory. I added that the 2 strips of RAM in the laptop, but it does n

  • Live photos became videos

    Hello I have an iPhone 6 s (which can take direct pictures) and an iPad 2 (both running iOS 9.2.1), as well as an iMac running OS X 10.11.3 and Photos 1.3. I noticed that some of my live (all older) photos became videos. For each, I get a completely

  • Installing WXP on Satellite A210-K15

    There are already more that month was bought by Satellite A210 - 15K. I want to install Windows XP Home edition, but I can't find the sata driver. Help! :_| ;\

  • Sending data through the serial port and the mscomm control is not the same as the original data

    Please find attached the mscomSerialWrite2.vi and the resulting image. Try it and find that when data "FFAE" 4040 EA41 D8FF is sent, the received data are "FFAE" 4040 EA41 3F I tried other data, the result is as follows: sending: 4164 8163 4341 03 re

  • How to convert my music files M4p (ITUNES) for windows media player with windows xp

    I want to covert my Itunes Music to my player mpo3 and have found several free downloads on the web. Many want a subscription rate. Does anyone know a good free download which did not charge me later or give me a virus. Thank you.  Snickman