DAQ traditional and generator of signals of NOR-5401

We have an older system using a signal generator of NOR-5401 (S/N 183962E-40) that runs with FGen 1.5.1 and 7.1 of NOR-DAQ

We just bought an another NOR-5401 (S/N 192888 A - 01) to install a second system.  However, it does not work with the software.  The software uses traditional DAQ. If I look in MAX, the NOR-5401 on the new system only comes in the DAQmx instruments.   On the old system, the NOR-5401 is available as traditional DAQ.

If I install an earlier version of the FGen (2.0 is the oldest, I can find) and NOR-DAQ 7.1 then the PC does not find a driver for the new OR-5401 at all.

Should what versions of FGen and NOR-DAQ I install to make it work?

Kind regards

Keven.


Tags: NI Products

Similar Questions

  • Conversion of a VI that uses OR-DAQ traditional to NOR-DAQmx

    Hello

    I'm trying to convert a VI that uses OR-DAQ traditional to NOR-DAQmx.  I'm almost there, but when I run my new rear version number 'read' and 'scan' are not the same.

    In the original version the "number read" always came back as 1 and "scan" backlog is always returned as 0.

    In the new version, "number readings" and "rear scan" could come back with any value.  It's sure to shake my recording of measures and VI the interaction with the rest of the program.

    I have attached a light version of the VI for the old OR-DAQ traditional and new OR-DAQmx that illustrate this problem.  The two VI is written in LabVIEW 2011 SP1.  I would be willing to upgrade to SP1 2013 LabVIEW if it would help solve the problem.

    I would be grateful for any guidance.

    Thank you in advance.

    I think I did.  Use-1 to erase everything in the buffer when the program is waiting for the countdown to the end and then just ask for 1000 measurements when the countdown reaches 0.  Do not need the Scan back or number reading.  Also don't need to add the measure in table 1 at a time because I get them all at once.

    I enclose a copy of my solution for all those who might need to do something similar in the future.

    Gary

  • How to generate analog signals?

    Hi all

    I'm trying to generate analog signals to simulate the position of the valve. I also want to simulate the position of the valve 0 - 5V (analog signal).  I've implemented the numeric position of the valve by using the toggle switches, but I want to implement analog signals.

    You can help.

    Thank you

    You can just use a random number generator.

    Since you have no generator hardware signals of NOR, I'm not sure why you are posting to this Board. Generic questions of LabVIEW. Post to this Board.

  • I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

    I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

    Ihab El-Sayed

    published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

  • NOR-DAQ traditional (old) devices of measurement and automation explore 4.7 with LabView2010 under Windows 7.

    In measurement and Automation Explorer 4.7, with LabView2010 in Windows 7, peripheral OR-DAQ traditional (old) appears under devices and Interfaces and it allows me to create a chassis SCXI-1000, and she agrees "Reset for NOR-traditional DAQ.  However, it does not search the modules in the SCXI1000, and when I ask 'trial', he says 'Impossible to test the chassis at this time.'  The entrance of NOR-DAQmx devices for the SCXI-1000 chassis has no problem and detects the modules very well.  I need the Legacy DAQ to a popular former teaching tool that has no equivalent in NOR-DAQmx.

    Unfortunately, NEITHER-DQA traditional (old) for Windows Vista and 7 functions of the only driver on Windows 7 32-bit, as seen on the page of the driver at the end of paragraph 1 Solution. I recommend you move your program to DAQmx.

  • MAX does not recognize NOR-DAQ traditional (old) devices * HELP

    I have a card PCIe-6259.  I want to use blocks of input-output in my program .vi (read Port DIO-DIO Port writing reading Digital Line), so I installed the version of NOR-DAQ traditional (old) devices 7.4.4.   But when I got to MAX (measures & Automation) and look on the left side under devices and Interfaces, I do not see the Tradional-NOR-DAQ tab; I see only the devices NOR-DAQ-mx, PXI, series and parallel system.

    Then when I go to run my program I get the error: error-10401 took place in a DIO Port Config Possible reason (s): NOR-DAQ LV: the specified device is not a product of National Instruments, the driver does not support the device (for example, the pilot exited until the device has been supported), or the device has not been configured using the Explorer Measurement & Automation.

    So, how do MAX to recognize that I have installed NOR-DAQ traditional (old) 7.4.4?

    Thanks for the reply!  I realized this too after going through the files for example... but thanks for the confirmation.

  • How to install traditional DAQ parallel and DAQ mx in Windows 7

    Solved with NOR-DAQ traditional (old) 7.5 for Windows 2000/XP/Vista/7 - BETA and DAQmx Version 9.2.2

    Add traditional Support for a system with mx drivers installed.

    You need two files of unzipped installation package.

    Traditional installation driver 7.5 Beta, maybe you should do this by selecting the Compatibility Mode for an Installation of Vista.
    Go to your installation directory NIDAQmx--> products NOR - DAQ_INF_files--> infInstaller.msi.
    Right-click the--> Uninstall.
    Go to your repertoire of the installer of the 7.5--> products Beta NOR - DAQ_INF_files--> infInstaller.msi
    Double-click--> installation and proceed with click Next, Next, finish.

    Check in the Windows Device Manager, if the driver Date is now 19/09/2007
    and the Version of the driver 1.0.0.16384 or similar 1.0.xxx.

    Reboot your system.

    MAX check if your device is displayed in MX-tree and traditional.

    It worked for me for a NI DAQ PCI 6025 e card.

    I used WES 7 Standard SP1 32 bit / x 86. I have confirmation that it should work on any Windows 7 32-bit as well.

    Thank you very much!

  • Connection diagram missing in DAQ Assistant generate the signalling block

    This is my first post so please excuse the quality of my description.

    When I double click on the block of data acquisition - Assistant, there is no tab connection diagram I can access to see how things are wired to the top. I have a NI USB-6211 connected by USB and it is used to control many different sensors and a power supply. Currently, he works for everything and is hard wired correctly, but only blocks DAQ Assistant has a connection diagram available, the other are not. One who has a connection diagram is used to measure a voltage. Others who do not are used to generate a signal. I would really like to be able to see patterns of connection for each block.

    -Any help would be appreciated

    -Thank you

    You can always do like those who never use the DAQ Assistant and read the manual. Right click on the device in MAX and selecting "stitching of the device" works too.

  • NOR-DAQ traditional vi not found in NOR-DAQmx

    Hello. We hope to control a detector via NI PCI-6533 (DIO-32HS). Our colleagues have implemented control programs in BT 7.1 to 7.3 of NOR-DAQ traditional. Now when we opened their programs on a PC installed with LV 8.6 and NOR-DAQmx 8.9, many vi was not located, including "DIO config.vi", "DIO wait.vi", "DIO clear.vi", "DIO read.vi", "Reset.vi Device", etc. We realized that they were supposed to come from vi.lib\daq\digital.llb and a few other .llb in the same folder. Apparently vi.llb\daq was installed by the traditional DAQ.

    We do not believe there is compatible with LV 8.6 traditional DAQ, which means that we need to replace those 'DIO *.vi' or 'Device reset.vi' with their counterparts DAQmx.  Could someone shed some light on how we should start working on that?

    Thank you very much.

    Xiaolan,

    Indeed, there is a traditional DAQ driver for LV 8.6. The installation can be found here.  I hope this helps.

  • DAQ Assistant Express Vi to acquire and generate data at the same time in LABView

    Can I run acquire it and generate the Express Assistant DAQ Vi at the same time in a LABView program? I am using LABView 2010.  It's acquire and generate a NI USB-6009.

    Thank you

    Mary

    You can acquire and generate the same VI but obviously you can't generate a wave form unless you do a single point at a time inside a loop with a sample on request and can live with low samples/s specifications.

  • Generate a signal FGEN 5421 and gettting on FScope 5122

    Hello

    (1) I need to generate a given signal

    A [Sin (WT) + N * Sin (2Wt + pi)] by using PXI or 5421.I join the program that I created using Labview.The problem, I face by using this program, is that the maximum amplitude I can get is 1. Second thing, it is that I need to build only for some periods.

    Later, I would like to make a sweep of this signal in the frequency range of 304kHz to 372kHz with a 0.5 kHz step size. How can I go about it?

    (2) I'll send this entry signalinto my system and I am able to see the answer on the oscilloscope using the NI Scope front. I would like to know how I can use a labview program and acquire my answer with adequate sampling.

    (3) I also need to convert the answer on my oscilloscope in a table of values so that I can import the table and generate the response in Matlab. How can I get the answer as a text file with a table of values?

    Waiting for your response,

    Thanks in advance,

    David

    I was wrong on my advise on the frequency sweep, kick these:

    http://zone.NI.com/DevZone/CDA/EPD/p/ID/3327

    http://zone.NI.com/DevZone/CDA/EPD/p/ID/1021

    http://zone.NI.com/DevZone/CDA/EPD/p/ID/5054

  • DAQ USB 6363 - generate digital data series through the single DIO line

    Hello

    I'm new with Labview, currently, I bought NI DAQ USB 6363 for generating control signals and signals analog accquire. I would like to send digital data series through one of the digital IOs with throughput of 30 kbps. Please see the attachment for the data frame. Could someone comment the feasibility of this? Y at - it codes for the example that I can refer to? Most of the examples I've looked at so far deals to generate several line instead of 1 single line. How can I achieve this?

    Thank you

    Diem

    Hey diem.

    After looking on your code, I understand what you were trying to do. Here's how I'd do. Usually we do not write code to clients, but you peaked my curiosity of! I hope this helps. Good luck!

    ~ kgarrett

  • PCIe-653 x with DAQ traditional

    Hello

    We want to update some of our network using a PCIe-6536. Is it possible to run this card with traditional NIDAQ?

    Does anyone have experience with the PCIe-653 x with DAQ traditional. Or is it only possible to run this card with DAQmx?

    Greetings

    Oliver

    Hi Oliver,.

    PCIe cards not are usually not supported by the old traditional DAQ driver.

    In any case, you should consider updating your application to DAQmx as TRANS. data acquisition support is quite limited (see also the official statement of OR below)

    "Caveat ".  NOR-traditional DAQ
    (Legacy) is an older driver with the obsolete application programming
    interfaces
    (API) for the development of acquisition data, instrumentation and control
    requests for former of National Instruments DAQ devices. You must use
    NOR-DAQ traditional (old) that in some circumstances. Refer to the
    File Readme of NOR-DAQ for a glimpse of the two API NOR-DAQ, the
    benefits of
    NOR-DAQmx and more information about when to use NOR-traditional DAQ
    (Legacy)
    including a complete list of devices supported, operating systems,
    application
    versions of the software and the language versions. You can install the most recent
    version of
    NOR-DAQmx software, available at ni.com/downloads.
    "

    Kind regards
    Bernd

  • How to connect dwyer SERIES 629 differential pressure transmitter to the acquisition of data 9219 and read the signal?

    Here is my sensor
    Pressure sensor

    Here's the DAQ data sheet:

    ACQUISITION OF DATA NOR 9219

    Here are my issues:

    First of all I don't know what is LO and HI exactly in the DAQ 9219 material.

    Second, I don't know what pin code I should connect the DAQ sensor signal wire. PIN 4 or 5 pin? The sensor has three pins, and I guess I should connect the other two wires to the power supply.
    Thirdly how to calibrate the sensor. In labview choose voltage in the wizard?

    I'm pretty new in this acquisition of data and I need your help.

    Thank you

    Hi SilasIII,

    Hmm well 3 sons are probably on the ground, the power and the return signal. The datasheet for the sensor says:

    First of all, you need to know which model you have (4-20mA, 0 - 5V or 0-10VDC). HI refers to the return signal, LO essentially means the land of the food that feeds the sensor. Then, you must get the 13-30 VDC supply. I don't think this should be too complicated and can be a simple wall DC power. You can learn how to create a custom in DAQmx scale. I hope that this is a starting point.

    Kind regards

    Eric

  • How can I generate sine signal long 10ms?

    Hello world

    I would like to do next: generate a sine or a DC signal for a period of time, 10 ms, that is to say after that, I want that my trips to Earth, so that the next time that I run the program. I use DAQ Assistant and DAQ 6211.

    Any help or advice will be great!

    Best regards

    Pero

    pero_kr wrote:

    Let's say I have a while loop in my program. When I press "run" the loop runs over and over again, until the stop condition occurs. How long (in milliseconds, microseconds or nanoseconds) takes to my PC to do the operation in an iteration of the loop?

    Hope this time was make myself clear. Thank you much for the help.

    That depends entirely on what is inside the loop, and what does your computer and what operating system you are using. You cannot create a deterministic loop with a non-deterministic operating system like Windows. An iteration of the loop could take 5 msec, or it might take 5 seconds if the OS thinks it must go off and do something very important, like updating your computer to solve all these security holes that has Windows. You can use call loops, but those who are not guaranteed to operate at exactly the specified frequency since you are at the mercy of the operating system.

    I still don't see why this information is important to you. Did you do as suggested and watched the examples supplied with LabVIEW and settle with DAQmx? They show you how to do the generation continues.

Maybe you are looking for

  • The new too short tab page

    Hello When I open a new tab, I am presented with the new tab page, that's fine. However, in recent days, I've found it does not display the last row of thumbnails (that they are supposed to be 3 rows and I can only see 2 of them). I checked the sourc

  • S3000-514: how to make the secondary battery to unload everything first?

    Hello world!After I ve managed to charge my secondary battery on my laptop (see my previous announcement), I'm now getting another "strange" problemWith my two batteries in and on the battery the first battery to discharge is the main battery - and n

  • How to change (not completely override) a sequence of the engine callback

    I understand the general idea behind changing engine callbacks, but how do I know what the original engine callback? In other words, how can I see the steps for TestStand engine by default reminders? Specifically, I work with the SequenceFilePostStep

  • Clone of SSD could not start

    I have an Acer Aspire 5742-6638 running on Core i5 - 480 M under Windows 7 64-bit.  I'm trying to clone my hard drive for an SSD.  Tried with the help of Paragon Drive Copy and EaseUS Todo Backup.  Both said cloned successfully, but the two could not

  • lost volume icon

    Active control panel, says no audio device.  My grandson removed program sigma telmundo (?) don't know if it's relevant.  Help, I am a computer dummy