data paging error / kernel stack inpage error

Just starting to get these errors.  I have a background of both limited computer posted patches go well above my head.  I tried to do a little, but I have to do something wrong.  Could someone help guide me through these errors solved?  I can boot the computer and restart it. This all started when I was on a game (taptiles) and he hit me, and then I couldn't get back to the game at all.  Then I started having problems when on the internet, it would be just me kick out unexpectedly. Now I only can access internet with chrome, can not access a recognizable homepage from internet explorer, the page is all the sentences and invite you. Any help you could provide would be wonderful.

Original title: How can I correct an error in pagination of data from the kernel / kernel stack inpage error on windows 8

Hello

Thank you for visiting Microsoft Communities.

I understand that you get the error message, and as you have problems with Internet Explorer.

Sorry to hear about the inconvenience caused. Do not worry, we are here to help.

Method 1: Microsoft online analysis

http://www.Microsoft.com/security/scanner/en-us/default.aspx

Download this online scanner and perform a full scan on the computer. This will remove any virus infection that is in the computer.

Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

Method 2: Check disk

This stop message indicates that the data page of the kernel of the required paging file cannot be read into memory. This stop message is usually caused by a bad block (sector) in a swap file, a virus, a disk controller or failing RAM error. In rare cases, it is caused when the resources of non-paged pool is exhausted. It is also caused by the defective material.

Right-click on the windows on the lower corner flag on the left

Select prompt (Admin)

This will open the command window and type please Chkdsk /f /r and press ENTER.

It will introduce the drive check and look for errors and try to remedy.

Note: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

For more information about the error, please see the link below:

Error message: KERNEL_DATA_INPAGE_ERROR

http://msdn.Microsoft.com/en-us/library/ms854944.aspx

For Internet Explorer related issue please follow the article below:

http://Windows.Microsoft.com/en-us/Internet-Explorer/IE-crashes-stops-working#IE=IE-10

Note: The feature reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Reset Internet Explorer is not reversible, and all the previous settings are lost after reset.

I hope this helps. And please answer if you still need help.

Tags: Windows

Similar Questions

  • kernel stack inpage Stop error: 0 x 00000077

    Original title: kernel stack inpage error
    Can someone help me with this problem please?

    I have the BSOD - Kernel Stack Inpage Error. Stop: 0 x 00000077

    I've had this for a few months now and cannot understand what is the cause or how to fix it.

    My security company (Kaspersky) told me that it was a corruption of memory.

    I have windows SP3 is already installed.

    ==================================================
    Dump file: Mini012812 - 02.dmp
    Crash time: 28/01/2012-14:20:12
    Bug Check String: KERNEL_STACK_INPAGE_ERROR
    Bug check Code: 0 x 00000077
    Parameter 1: 0x00000001
    Parameter 2: 0x00000000
    Parameter 3: 0x00000000
    Parameter 4: 0xf792ad24
    Caused by the driver: ntoskrnl.exe
    Caused by the address: ntoskrnl.exe + 22f43
    Description of the file:
    Product name:
    Company:
    Version of the file:
    Processor: 32-bit
    Plant address: ntoskrnl.exe + 22f43
    Stack address 1: ntoskrnl.exe + 3be48
    Stack address 2: ntoskrnl.exe + 68dd6
    Battery 3 address: ntoskrnl.exe + 692 has 6
    Computer name:
    Full path:
    Number of processors: 1
    Main version: 15
    Minor Version: 2600
    Size of the dump file: 90 112
    ==================================================

    ==================================================
    Dump file: Mini012812 - 01.dmp
    Crash time: 28/01/2012 11:59:40
    Bug Check String: KERNEL_STACK_INPAGE_ERROR
    Bug check Code: 0 x 00000077
    Parameter 1: 0xc00000b5
    Parameter 2: 0xc00000b5
    Parameter 3: 0x00000000
    Parameter 4: 0x11a81000
    Caused by the driver: ntoskrnl.exe
    Caused by the address: ntoskrnl.exe + 22f43
    Description of the file:
    Product name:
    Company:
    Version of the file:
    Processor: 32-bit
    Plant address: ntoskrnl.exe + 22f43
    Stack address 1: ntoskrnl.exe + 3afa9
    Stack address 2: ntoskrnl.exe + 3be1b
    Battery 3 address: ntoskrnl.exe + 68dd6
    Computer name:
    Full path:
    Number of processors: 1
    Main version: 15
    Minor Version: 2600
    Size of the dump file: 90 112
    ==================================================

    Let me know if you need anything that anyone else. Thank you!

    Hello

    Error code KERNEL_DATA_INPAGE_ERROR STOP: 0x0000007A indicates that the data page of the kernel of the required paging file could not be read into memory. It seems that there are some problems with the hard drive.

    See the link below to fix the problem.

    You receive an error message on a Windows XP-based computer: "Stop 0 x 00000077" or "KERNEL_STACK_INPAGE_ERROR"
    http://support.Microsoft.com/kb/315266

    Note:
    Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

  • Error KERNEL STACK INPAGE ERROR on Windows Vista SP2 blue screen

    Original title: KERNEL STACK INPAGE ERROR

    What can cause a crash with the KERNEL_STACK_INPAGE_ERROR message in a blue screen.  Ive had just a new hard drive installed.  Running Vista Home Premium with Service Pack 2.  Usually occurs when returning from standby or Hibernate mode.

    Hi JerryHines,

    This problem can occur if a requested page of kernel data could not be read on the paging file into memory, or the master boot record is infected with a virus.

    Method 1:  I understand that you have installed a new hard drive, run the disk check to repair bad sectors on your hard drive

    Note: CHKDSK would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of DATA loss from that particular area.

    Check your hard drive for errors

    http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

    Method 2:  Put the computer to boot and then check if the problem persists

    Follow step 1 in the link below,
    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

    Method 3: Disable and re-enable the hibernation, see them steps outlined in the article below

    How to disable and re-enable hibernation on a computer that is running Windows

    http://support.Microsoft.com/kb/920730

    For more information, please visit the link below

    How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista

    http://support.Microsoft.com/kb/950686

    Resolve stop (blue screen) error in Windows 7

    http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

    (Article applies to Windows 7, not valid for Windows Vista)

  • Error on kernel stack inpage error and blue screen

    (Note: this post was created on behalf of another user.)

    Recently, my PC had blue screen errors.  Thinking it was probably a problem of aging HD, the HD has been replaced and a new install of Win XP Home Edition with Service Pack 2.  Blue screens persist despite the new drive.

    The error is a "Kernel Stack Inpage Error".

    It is a new drive with the same errors as before so I think that it is not a virus and probably a problem with another piece of hardware.  There is a minidump file available if need be.

    Can someone please help with these errors?

    Thank you.

    If you would like to get BSV and run it, then choose:

    Options, lower pane Mode, all the drivers

    You'll be on your way and see the battery and your ATI drivers.

    Updates Microsoft released the second Tuesday of each month (Patch Tuesday) so it would be on 07/12, but since you have SP2, I can't say what would happen or what updates you decided to install.  If you have accepted the recommendations of MS for video drivers (which are usually poorly), who knows what is happening.

  • data paging error Kernal

    I have dell 1545 laptop inspiton. for last 4 months if I want to install wibdows 7 ther may be an error with kernal data inpage error blue screen. I have run CHKDSK/p & CHKDSK C: /F /Rcommand but after the problem is continuous. Please tell me my hard drive is bd or I have to buy new hard drive?

    Hello

    Take a look at the answer in the following link:
    http://social.technet.Microsoft.com/forums/en-us/w7itprohardware/thread/7b354864-297e-428A-9026-bfd822137ef1

    Thank you

  • Blue screen kernal Windows 8 data paging error? Help!

    I've had my laptop for 3 months now... And I get this blue screen that cutting down of my computer saying kernal_data_inpage_error.

    I have a Sony Vaio Windows 8.
    Sometimes after closing, it takes forever to login on windows, or when
    I go to the office, nothing shows up, and he said: I got an error and the process could not execute leave my laptop unusable.
    He arrived at a point where I can't do anything now, I did a memory diagnostic test that says that everything was fine and also a driver scan that says once again everything was fine.
    The screen opens every time that, usually, when
    Browsing the Internet or watching a movie, but he can do it when I do anything.
    I is there a solution to this or am I better off take it for a free repair of the place, that I brought?
    Any help is very appreciated!

    These were related to your Symantec.  I remove it and use the built in Defender.  More update the drivers below



    CLVirtualDrive.sys 2011-12-26 09:26:47 fffff880'046ac000
    sows.sys 10/06/2012 21:36:13 fffff880'0613 has 000
    Rt630x64.sys 12/06/2012 09:37:53 fffff880'06088000
    RtsPStor.sys 06/13/2012 06:08:38 fffff880'06031000
    SFEP.sys 06/18/2012 04:11:46 fffff880'06131000
    IntcDAud.sys 19/06/2012 10:40:51 fffff880'07754000
    20/07/2012 Igdkmd64.sys 17:47:55 fffff880'0525 d 000
    Ironx64.sys 23/07/2012 20:34:50 fffff880'04578000

    How to find drivers:


    Search
    Google for the name of the driver
    Compare the Google results with what is installed on your system to determine on what device/program, it belongs to
    Visit the web site of the manufacturer of the hardware or program to get the latest drivers (do not use Windows Update or Device Manager Update Driver function).
    If there are difficulties to locate them, post back with questions and someone will try and help you find the right program

    The most common drivers can be found on these pages:
    http://www.carrona.org/dvrref.php
    http://SysNative.com/drivers/

    Driver manufacturer links are on this page: http://www.carrona.org

  • Data from the kernel page fault / Hanging CHKDSK / Missing Restore points

    I'm running a quad core 2.8 g with Vista 32 home premium.

    The last two days, my pc has been extremely slow start. Yesterday, I got 2 blue screens.

    first of all a kernel stack inpage error, second - kernel data Inpage Error

    0x0000007A (0xC0413DD8, 0c000000E, 0x63BOE860, 0x827BB58D)

    I also had a problem where McAfee maintained disabling direct scan. This problem has been fixed with a download from mcafee.

    I tried to do a system restore but found that all my restore points before the problem had disappeared.

    Virus analyses are turning to the high own.

    Attempted to run CHKDSK on the C drive, but it took 1.5 hours to reach stage 5-5 and hung up to 15%

    All my drivers and Windows is up to date. Recent change of system is only that I got a notification via update of windows that there is an update for my Gforce 9800 GX2 graphics card. I have tried to update the driver but had an error, because my current driver was more recent than what was pushing the windows.

    Looks like a disk, cable or controller error.  The easiest thing to check can be cable - make sure it is snug and replace it with a good known if possible.  0xc000000e STATUS_NO_SUCH_DEVICE - "a device which does not exist was specified."  Essentially, the data that are paged to disk could not be read because the device does not exist (or has ceased to be available).

  • Cq42-268tx (paging of kernel data error)

    Hello

    I got this error two weeks there (paging of kernel data error).  I found a similar problem "solved" posted in the forum, but I think mine is different.  The parameters given after the "STOP: 0x0000007A (parameters) are different so I think it could be worse."

    For the last three days, this error frequently occurs five minutes after startup. I did a few tests of memory and it seemed fine, but the hard drive test is always stopped at 56%.  I tried the test twice more and still give the same results.

    What could be the problem? Hard drive? memory? virus? (im sorry not a tech guy).

    BTW, my Compaq laptop is 2.5 years.

    Thank you in advance.

    See you soon!

    Hello

    There are opportunities, it could be the hard drive itself. If the HARD drive test is not complete, then try to run extensive testing as shown in the link below:

    Screening of hardware failures (Windows 7, Vista)

    If you have all of the options presented in the above link, then you may need to install the latest UEFI Diagnostics on the Site of HP Support under diagnosis. (Select your windows version 64 bit or 32 bit).

    If he continues to do the same thing then most likely the HARD drive needs to be replaced

  • the core data entry error - windows 8

    It seems to me to get the data entry error on my windows kernel 8 all the days. I ran chkdsk many times before, Defrag, reinstalled a clean copy and ran virus, malware scans.

    Kernel error of data entry displays the blue screen and restarts and is very well after the restart, but a few days later, the error will appear again. Please help on how I can fix this?
    I'm not sure as to what files I need to download. Please advice.

    ShinPark3

    They are usually related to a problem with HD.  Before running CHKDSK I would remove Avast and express cache (both are know-how BSOD)

    Avast can be a cause of BSOD.

    Please remove and use the Defender built-in at least to test

    http://files.avast.com/files/eng/aswclear5.exe

    A CHKDSK F: /R

    CHKDSK WARNING: while running chkdsk on the drive if bad sectors are found when chkdsk attempts to repair this sector all the data available in this area may be lost.

    Run CHKDSK/r/f of a high (run as administrator) command prompt.
    Do this for each hard drive on your system.
    When he tells you, he cannot do at the moment – and ask you if you do not want to do it at the next reset - answer Y (for Yes) and press ENTER.

    Then restart and let the test to run.
    It may take some time for him to run, but keep an occasional eye on it to see if it generates errors.
    http://www.howtogeek.com/HOWTO/Windows-Vista/Guide-to-using-check-disk-in-Windows-Vista/

    See "CHKDSK LogFile' below to verify the test results.

    B Elevated Command Prompt:
    Click on start and type "cmd.exe" (without the quotes)
    At the top of the search box, right-click on Cmd.exe and select "Run as Administrator"

    C CHKDSK LogFile:
    Click Start and type "eventvwr.msc" (without the quotes) and press enter
    Expand the topic the Windows logs, and then select the Application log file entry.
    Double-click the Source column heading.
    Scroll down the list until you find the entrance to Chkdsk (wininit for Win7) (winlogon for XP).
    Copy / paste the results in your next post.

  • Satellite A300D-135 - BIOS - System Configuration data read error

    After starting a Satellite A300D-135 laptop computer, the following error message appears:


    3070M extended RAM passed
    512 KB of L2 Cache
    System BIOS with a shadow
    Video BIOS with a shadow
    ATAPI CD-ROM: TSSTcorp CDDVDW TS-L632H
    Fixed disk 0: TOSHIBA MK2546GSX
    Initialized the mouse
    ERROR
    System Configuration data read error

    Press to resume, installation

    After pressing F1 the machine starts Windows, very well, but the error message is quite irritating, while it comes with a loud BEEP

    I tried the following things so far (in that particular order):
    -Load BIOS default
    -Flashed the BIOS with the latest version of the BIOS (2.80) for this type of model
    -Reinstalled windows with HARD drive format

    All the these did not work.

    I saw the same message appearing on several places on the internet (on different laptops with a Phoenix BIOS in common), but so far I have not been able to find a working solution.

    It might me a hardware problem, but all devices (vga, soiund, lan, wifi, usb, hdd) seem to work perfectly under Windows, so this does not seem the question). Another solution that is mentioned in some forums, replace the battery. But because the phone keeps time correctly I don't think it's the case either.

    Any ideas?

    Kind regards
    GJ

    Hello

    The POST (power on self-test) BIOS checks and detects errors on the motherboard.
    I think it has something to do with the hardware on the motherboard problem.
    I doubt that you can solve this if update of the BIOS and the BIOS default settings didn't change that.

    What to say; I think that the technician of the ASP should run tests to check what's wrong or what cause this I think it is question of s mobo.

  • Equium A300D - 13 X - Configration system data read error

    Hello

    I have a problem with my Equium A300D - 13 X laptop, everytime I turn on my laptop it starts and loads the initial startup screen as usual, Toshiba once asked that loud "BEEP" comes from my laptop, and lists the following information:

    Phoenix TrustredCore (tm) NB
    Copyright 1985-2006 Phoenix Technologies Ltd.
    All rights reserved

    Herring of the ITA (DDR2 + T/RS690M/SB600)
    CPU speed = 2000 MHz

    639K system spent RAM
    1918M extended RAM passed
    1024 KB of L2 Cache
    Occult system BIOS
    Video BIOS with a shadow
    ATAPI CD-ROM: MAST * ADVD-RAM UJ-850 S
    Fixed disk 0: WDC W2500BEVT-00SCSTO
    Fixed disk 1: Hitachi HTS542520K9SA00
    Initialized the mouse
    ERROR
    System Configuration data read error

    Press to resume, installation

    I replaced the hard drive and flashed the BIOS settings as advised by Toshiba Helpline but the problem persists.

    Help, please! because the "BEEP" is now getting on my nerves!

    See you soon

    Hi andrew_net82,

    It seems that the BIOS has detected an error with a certain part of material...

    Before doing something I recommend you load the default settings in the BIOS. If you are in the BIOS Setup, press the F9 key.

    If it doesn t work you need for professional assistance from an authorized service I think. Guys need to check which part of the material is defective and must be replaced.
    List of the ASP, you can find on the official website of Toshiba.

  • Data length error! Helps the release of Keyence micrometer

    I am connected to a micrometer of LS7600 Keyence, and I am able to send commands to the micrometer, as well as receive structred outputes.  For example:

    Command: M0, 1

    Return: ER, M0, 20

    Soul ER error, M0 is my exit command, and 20 means DATA LENGTH ERROR.

    I use a very basic VISA program that connects to the Keyence via my Serial Port.

    So when the micrometer Keyence attempts to send the data I requested, it apparently can't do because it encounters a data length error.  I know it's a problem with my labview software because I can output these values successfully using a Hyperterminal connection.

    The data SHOULD go back which looks like this: M0 + 25.2531

    It's just 12 bits?  Can anyone think why labview does not accept this string?

    Check the display format of the indicator, that you look at the number.  It by default 6 significant digits, is exactly what you say.

    The integer is in the orange wire, just your indicator is not set to show them all to you.

  • Computer laptop Gateway does not load windows Vista, reads configuration data read error: System.

    OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
    4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:

    9D.03 BIOS version

    632K RAM passed system
    3966M extended RAM passed
    1024 KB of L2 Cache
    System BIOS with a shadow
    Video BIOS with a shadow
    ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
    Fixed disk 0: WDC WD2500BEVS-26VATO
    Initialized the mouse
    Updated System Configuration data
    ERROR
    System Configuration data read error.

    I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).

    If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.

    At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.

    http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!

  • Dat2.data version error

    I get the dat2.data Version error when I try to print, or even to open Microsoft Word 2007.  It started when I loaded the new epson drivers on my computer.  I tried to uninstall the epson SW but it won't let me, it times out.

    Hi Tom Callaghan,.

    Welcome to the Microsoft Answers community.

    Do you have which version of the driver installed?

    You can install the old driver version and check.

    I suggest to start your computer in clean boot mode, and then uninstall the printer driver and restart your computer. Reinstall the printer drivers.
     
    Method 1: Steps to uninstall and reinstall the printer driver.
    1. click on the Start button and select Control Panel.
    2. click on programs.
    3. click on programs and features.
    4. now uninstall the printer drivers.
    5 restart your computer. This will automatically install the appropriate drivers for it.

    You can also download the driver for it from the manufacturer's Web site.
    http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?OID=-10222&infoType=overview
     
    Method 2: Steps to start in clean boot mode:

    1. click on start, type msconfig in the search box and press ENTER.
    If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
    2. in the general tab, click Selective startup.
    3. under Selective startup, clear the check box load startup items.
    4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
    5. click on OK.
    6. When you are prompted, click on restart.

    http://support.microsoft.com/kb/331796 . In addition, see the section on how to restore your computer to a Normal startup mode.
    If the methods above does not solve your problem, and then run system restore.

    Method 3: System Restore will take your computer state permeable when it did not face such a problem, this can be done by selecting the correct restore point.

    To restore the operating system to an earlier point in time, follow these steps:

    1. Click Start, type system restore in the search box, and then click System Restore in the list programs.

    If you are prompted for an administrator password or a confirmation, type your password or click on continue.

    2. in the System Restore dialog box, click on choose a different restore point and then click Next.
    3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.
    4. click on finish.

    For more information, visit the links below:
    http://support.Microsoft.com/kb/936212/
    http://support.Microsoft.com/kb/826862

    Hope this information is useful.
    Let me know if it worked.
     
    Thank you, and in what concerns:
    Umesh P - Microsoft Support

  • CanoScan 4200F gives error - "Twain data transfer error".

    I have a new Windows 7 PC and unable to use CanoScan 4200F, he returns with "Twain data transfer error".  Worked fine with Windows XP.  What should I do

    to make it work?

    Check the manufacturers technical support for latest drivers site, they have Windows 7 drivers that you can download and install. Download little correct level for your computer - 32 or 64 bit - and then install them.

    CanoScan 4200F drivers:
    http://www.USA.Canon.com/Cusa/support/consumer/scanners/canoscan_series/canoscan_4200f?selectedName=DriversAndSoftware

    To see if you have Windows 7 32-bit or 64-bit:

    1. Open system by clicking the Start button, right-click computer, and then clicking Properties.
    2. Under system, you can view the type of system, it will say 32 or 64 bits.

Maybe you are looking for