Similar Questions

• Camera not present error & Baumer GigE Test Packet (0xBFF69031)

  Hello

  I tried various fixes to other messages and still have problems setting up my TXG06 Baumer with LV running NOR-IMAQdx 4.0.

  The camera shows OK in the SDK of Baumer, but when you try to recover an image NI Max I get "the system has not received a test package...". "If I let MAX OR open and try the same device, sometimes I mistake"not present Camera. '... "instead, even if it is still running ok on the network.

  I added an exception to the windows firewall, enabled extended packages, tried to reduce the size of pcaket and tried without the Baumer software installed. Still no joy.

  Any help would be appreciated.

  Hi, noodles,

  It's quite strange, you seem to have tried all the troubleshooting steps that firstly, we recommend. How reduce you the size of packages to? Have you tried to set very low (~ 1 k) to see if even then you still cannot take a wink?

  What ethernet card are you using? (Just to be sure it's GigE) and have you tried this unit with another PC to see if the problem with your ethernet card?

  Thank you

• C# Oracle.DataAccess calling a stored procedure with a date parameter throws formatexception

  C# Oracle.DataAccess CommandType.StoredProcedure is OracleDbType. Date

  I can't get my code to call an oracle procedure that has an order date.

  I receive a System.FormatException occurred in Oracle.DataAccess.dll

  I tried to assign the param. Value = DateTime and also tried assigning as a string formatted with no luck.

  What is the magic formula, I need to call this function?

  Here is a code snippet:

  OracleCommand cmd = new OracleCommand();

  cmd connection group appConn;.

  cmd.CommandText = "mypackage.myprocedure";

  cmd.CommandType = CommandType.StoredProcedure;

  Param = new OracleParameter ("iDateParamter", OracleDbType.Date, ParameterDirection.Input);

  Param. Value = "August 31, 2015."

  Here are other formats I' tried... ved param. Value = myDateValue.ToString ("dd - MMM-yyyy"). ToUpper(); (/ / "MM/dd/yyyy"); 'YYYY-MM-dd'); "MM-dd-yyyy");

  cmd. Parameters.Add (param);

              BindByName. cmd = true;

              cmd ExecuteNonQuery());

  Shame on me..., you can close this message

  It was not for the error on my date field, I had another parameter that has been attributed to a string instead of an integer.

  For the record, this has worked well for me:

  Param = new OracleParameter ("iActvyPerDate", OracleDbType.Date, ParameterDirection.Input);

  Param. Value = li. ActvyPerDate.ToString ("dd-MMM-yyyy"). ToUpper();

• Data parameter problem

  Hello

  I am facing a problem with the parameter Data;

  I can't able to query the data for different dates in the range, but I am able to query the data for the same date in the range.

  Select the statement-

  Select RCT.GL_DATE in the RCT RA_CUST_TRX_LINE_GL_DIST_ALL

  where TO_CHAR (TRUNC (RCT.GL_DATE), 'DD-MON-YY')

  between TO_CHAR (TRUNC (TO_DATE(:P_GL_DATE_LOW)), 'DD-MON-YY')

  AND TO_CHAR (TRUNC (TO_DATE(:P_GL_DATE_HIGH)), 'DD-MON-YY');

  I am able to get the data for the date range - 05-JAN-2015/05-JAN-2015, 07-JAN-2015/07-JAN-2015 and so on...

  I'm not able to get the data for the date range - 05-JAN-2015/07-JAN-2015, 07-JAN-2015/09-JAN-2015 and so on...

  Can someone help me on this issue.

  Thanks in advance!

  Dilip Manon

  As John pointed out, use the date data type to compare dates:

  Select RCT.GL_DATE in the RCT RA_CUST_TRX_LINE_GL_DIST_ALL

  where RCT.GL_DATE

  (between TO_DATE(:P_GL_DATE_LOW)), 'DD-MON-YYYY')

  (AND TO_DATE(:P_GL_DATE_HIGH)), 'DD-MON-YYYY');

  Using TO_CHAR to compare dates, not only do you risk to make mistake and forget certain values, but also in this case stop you an index on GL_DATE may be used.

• Complex input for the control of ws data parameter

  Hello

  If I have a web service-based data control and exposed in the web service method accepts an array of custom as an input parameter objects, how can I set the value of the input parameter.

  In this link http://susanduncan.blogspot.com/2006/09/dealing-with-complex-input-params-in.html , we create a table 'Goods' (custom type), but here we use a proxy and the class of 'Élément' is generated by JDev.

  How can we do it if we were using a web service data command instead? (The "Item" class will not be generated)

  Thank you

  Elias;

  You can not. You must use a proxy for this.

  Timo

• Date parameter

  Hello
  I'm working on OBIEE (11.1.1.6.2 (120604.0813 BP1 64-bit Build)) with BI Publisher. My data set is made with a query and this query works well with Oracle SQL Developer.
  
  I have a parameter called HELP
  
  Data type: Date
  Default value: {$$SYSDATE ()}
  Parameter type: Date
  The Format string date: Dd-MM-YYYY
  
  I want to do:
  
  
  CASE
  WHEN ((:HELP) - BILL.) INVOICE_DATE) BETWEEN 0 AND 30
  THEN
  
  It gives me: ORA-00932: inconsistent data types: expected TANK a DATE.
  
  I tried to wrap them, I could, without success...
  
  
  From the XML file, I can see that:
  < HELP > 2013-03-26T 00: 00:00.000 - 04:00 < / HELP >
  and
  THE INVOICE. INVOICE_DATE = 2009-01-31 T 00: 00:00.000 - 05:00
  
  
  Since I understand that it isn't the format of good time for Oracle, someone like any idea how I could solve this problem.
  
  Thank you

  don't know obiee but in ebs are fnd_date.canonical_to_date for this

  also
  >
  Data type: Date
  Default value: {$$SYSDATE ()}
  Parameter type: Date
  The Format string date: Dd-MM-YYYY
  >
  and

  2013-03-26 T 00: 00:00.000 - 04:00

  HM hm

  Date 2009 - 01-31T 00: 00:00.000 - try to 05:00

  SQL> select to_date(substr('2009-01-31T00:00:00.000-05:00',1,10),'yyyy-mm-dd') from dual;
  
  TO_DATE(SUBSTR('2009-01-31T00:
  ------------------------------
  31.01.2009
  
  SQL> 
  

  and

  CASE
  WHEN ((to_date(substr(:HELP,1,10),'yyyy-mm-dd')) - INVOICE.INVOICE_DATE) BETWEEN 0 AND 30
  THEN
  

• Calling stored procedure with an input of DATE parameter

  Hello. A question about the Date input parameters when you call a stored procedure.
  
  I have a procedure that takes a DATE as input parameter. I would DATE this value to include a time element.
  
  My Application Module method takes an input as a java.util.Date (myParamDate) parameter - that will preserve a time element (?).
  
  However when I create the CallableStatement, I am trying to set the parameter using setDate like this (for the param 5):
  

              st = getDBTransaction().createCallableStatement("begin cs_my_pck.request_values(?,?,?,?,?,?,?,?); end;", 0);            
              Connection myConn = st.getConnection();
              ArrayDescriptor myArrDesc  =  ArrayDescriptor.createDescriptor("CS_FIELD_TABT", myConn);
              Array sqlParamNameArray = new oracle.sql.ARRAY(myArrDesc, myConn, paramNames.toArray());
              Array sqlParamValueArray = new oracle.sql.ARRAY(myArrDesc, myConn, paramValues.toArray());
              Array sqlFilterNameArray = new oracle.sql.ARRAY(myArrDesc,myConn,filterNames.toArray());
                  
              st.setString(1, repType);
              st.setObject(2, sqlParamNameArray);
              st.setObject(3,sqlParamValueArray);
              st.setObject(4,sqlFilterNameArray);
  
              java.sql.Date myRepDate = new java.sql.Date(myParamDate.getTime());
  
              st.setDate(5,myRepDate);
              
              System.out.println("Report Date = " + myRepDate.toString());
              st.setString(6,repUser);
              st.setString(7,repAttach);
              // set out param
              st.registerOutParameter(8, Types.NUMERIC);
              st.execute();

  I understand java.sql.Date does NOT include a time element. But setDate() only accepts a java.sql.Date so my parameter of the procedure ends with a zero time element.
  
  How to call this procedure keeping the time element?
  
  Thank you.

  It includes the time element, if you want more precision with time stamp.

  http://docs.Oracle.com/javase/6/docs/API/Java/SQL/date.html

• How to extract the date parameter, which must appear in the report model?

  Hi gurus and Experts.
  
  I need to shoot the date setting, I chose at RANDOM to appear in my report model? How this code at RANDOM?
  
  Identifier are: dto and cdes
  Channel marker date: MM-DD-YYYY
  
  Kind regards
  
  JP
  
  Published by: user10955574 on November 10, 2010 02:38
  
  Published by: user10955574 on November 10, 2010 02:39

  Declare the parameter in the model as
  
  and use it as

• Primary key several columns with Date - parameter problem

  All,
  I'm having a problem where I can not find the answer to. I looked upstairs and down nothing helps. Help, please.
  
  The issue is that I have a table that has a primary key of several columns and a column is a date, and the other is a string. I have a simple search and I want a picture update of the results table that users can click on and go to another page to update this record. The question is when I launch an appeal based on the updated image, I also want to define the settings based on the record that I have selected. So I put the string parameter and that works very well. The problem is with the date. When I put the setting date this market but he chops off the coast of the timestamp. Later when I try to access this setting "("dateParameter") pageContext.getParameter"; that it will bring a date as December 15, 2008 but I need the whole date and time stamp (i.e., December 15, 2008 10:20:33) to properly identify the record.
  
  Help, please!
  
  Thank you
  Colby J

  Hello

  because each parameter go into url as a format string, so you will never get the full date with timestamp setting, the solution would be to

  1.) set a fire on the photo update action, give his name to the event as "update."

  (2.) by clicking Update photograph fires this event.

  (3.) processFormrequest in the controller method

  OAApplicationModule am = pageContext.getApplicationModule (webBean);

  If ("update".equals (pageContext.getParameter ("event")))
  {
  This will give you the select line when you click Update

  String rowReference = pageContext.getParameter (OAWebBeanConstants.EVENT_SOURCE_ROW_REFERENCE);
  Line VORowImpl = (EmployeeSummaryVORowImpl) am.findRowByRef (rowReference);
  Timestamp sdateVal = (String) row.getAttribute ("Date value");

  This will transfer the values to the next page
  pageContext.putTransactionTransientValue ("transferdvalue", sdateVal);

  }

  and in the next page, you can get the value as follows

  timestamp getDateVal = pageContext.getTransactionTransientValue ("transferdvalue" l);

  hope this will solve your problem, please let me know if you face any problem

  thanx
  Pratap

• error of variable date "parameter missing."

  Hello!
  
  I created a my_date_variable, which is then used in the PL/SQL procedure,
  for example, "create table my_test in select #my_date_variable from dual;"
  but when I run this in ODI, I get the following error:
  
  com.sunopsis.sql.SnpsMissingParametersException: missing parameter
  at com.sunopsis.sql.SnpsQuery.completeHostVariable (SnpsQuery.java)
  at com.sunopsis.sql.SnpsQuery.updateExecStatement (SnpsQuery.java)
  at com.sunopsis.sql.SnpsQuery.executeUpdate (SnpsQuery.java)
  at com.sunopsis.dwg.dbobj.SnpSessTaskSql.execStdOrders (SnpSessTaskSql.java)
  at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTaskTrt (SnpSessTaskSql.java)
  at com.sunopsis.dwg.dbobj.SnpSessTaskSqlS.treatTaskTrt (SnpSessTaskSqlS.java)
  at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask (SnpSessTaskSql.java)
  at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep (SnpSessStep.java)
  at com.sunopsis.dwg.dbobj.SnpSession.treatSession (SnpSession.java)
  at com.sunopsis.dwg.cmd.DwgCommandSession.treatCommand (DwgCommandSession.java)
  at com.sunopsis.dwg.cmd.DwgCommandBase.execute (DwgCommandBase.java)
  at com.sunopsis.dwg.cmd.e.i (e.java)
  at com.sunopsis.dwg.cmd.h.y (h.java)
  at com.sunopsis.dwg.cmd.e.run (e.java)
  at java.lang.Thread.run(Thread.java:619)
  
  Variable is set to default, I tried all the actions of 3 - Historize, the most recent value, not persistent.
  When I do the same thing with the numeric variable, my test scenario works perfectly.
  So, this problem seems to be related only to a date variable, or maybe I don't know how to use it.
  
  Karlis
  
  Published by: Karlis 26 May 2009 08:37

  Hello

  I created the variable #my_date_variable. With the default value according to 2009-01-01 and not persistent.
  Then I created the procedure with the following expression.

  "create table my_test_aw as select '#my_date_variable' aw double."

  Table is created with the name of the column as aw and data value "2009-01-01.

  I would like to know what is your problem?

  Kind regards
  Ashwini

• cell data parameter

  Can't find where to turn off LTE / 4G on the airwaves of the ipad 2

  If your iPad is indeed a cellular connection, you should be able to control what cell data to useyour applications of:

  Settings > cellular.

  For a more general framework, on a trip abroad for example, simply turn the settings > Airplane Mode ON.

• default value of the parameter date problematic SYSDATE

  Hello
  
  I finally discovered why a report of problems, but have no solution to the problem.
  
  After the first run of the report and MORE (DESKTOP is no problem), I can open is no longer the LOV for any of the settings. The LOV icon is available, but nothing happens when you click it.
  
  Now, I know the problem is a specific condition based on a date parameter.
  
  The State is testing a date field against a setting that is based on NONE and has a default value of today. If I use effective dates in the setting I have no problem. If I use today or SYSDATE, then I can only run the report once. After that I can't choose any LOV in any of the settings. If I change the today or SYSDATE to a real, date is well again.
  
  The State of origin that was used was based on a calculated field due2 defined as: DECODE (:due,'TODAY',SYSDATE,TO_DATE(:due,'DD/MM/YY'))
  
  I tried to change the condition of:
  
  date field < = TO_DATE(:due,'dd/mm/yyyy')
  
  but also causing problems if I used SYSDATE or today in the parameter.
  
  I then tried to change the calculated field to due2:
  Decode (:due,'TODAY',to_date(sysdate,'dd/mm/yyyy'),to_date(:due,'DD/mm/YY'))
  but it does not work.
  
  Any suggestions?
  
  Thank you.
  Leah

  Hi Lea,.
  Try using 'CASES' instead of 'Decode' in your state:

  -case when: due = trunc (sysdate) then 'Today'
  of other end TO_DATE(:due,'DD/MM/YY')

  Maybe it will solve your problem.

  Note that this is problematic, because if the user enters an invalid date you will probably get an error.

  I could do this a bit different...
  1. create an optional parameter based on the date (so that I'll have the calendar)
  2 create a condition where the parameter is empty, it will use SYSDATE.
  for example:
  =: due
  OR (: due is null AND = trunc (sysdate))

  Tamir

• For cameras Baumer vision acquisition software

  I have the EXG50 Baumer GigE camera.

  On their website I found that it is supported by

  Vision acquisition software 8.5

  This means that it is included in later versions with Vision acquisition as well.

  Or should I only use this version for the camera?

  Is the reason I ask: I have the Vision Aqusition worm 8.6 software.

  It works with the camera in MAX, but there a number of controls on the camera and picture on it has gone from left to right. Please see image attached.

  I had similar problem. Deactivation of the resolved song data. Thank you.

• Cannot attach email word documents get the message 'enable documents and data '.

  Cannot attach a word document to an email. I get the message 'Enable documents and data' and it says that it is disabled. Don't enter iCloud setting there is no Document and data parameter. Is it because I use a free version of work?

  Whether the app is the word document?

  You can view the document word on the iPad?

• Use creation to read alternating channels and data

  I have a csv file that I am trying to create a use. The help file says that if I specify a line in the form of data, then all subsequent lines must also be given.

  The first line of my file is a header parameter names of test. I would like these are the names of channel for the actual data (parameter values) that follow on the next line.

  Then I have a blank line, then a line with my main data channel names. The following lines are then the main actual data.

  I'm sure I need a VBScript to do this, but am a little to get something that works based on examples that I found on the shelf.

  I want to bring in the header data in the data portal so that I can put some of them together with graphs in my reports.

  I have attached a sample data file. Also, I would generally ignore some of the columns of data (in this case, columns 3 to 10)

  Thanks for your suggestions!

  Hi Greg_Gran-

  I have attached a personalized use which will be structured according to your posted example files and will ignore the third to the tenth data channels.

  To use the use, simply unzip the cover record attached to your hard drive.  Double-click the *.uri file that is included to register for use with your computer.  Once you get the registration successful dialog box, you will be able to load your data files.  Because CSV is a format of generic file with many variations, you may need to push the priority of this particular use for the *. "" "Extension CSV through DIAdem NAVIGATOR" settings "My DataFinder ' configure ' menu File Extensions so that this use is always used instead of the other *. DataPlugins CSV.

  I didn't know if you wanted to ignore the third to the tenth of all columns of data or from time to time, so I built a small hook in the use that will allow you to adjust the 'package' of ignored channels (e.g.: 3-10, 1-5, 21-30).  To change the range of the use know when loading:

  1. Select the NAVIGATOR tiara.
  
  
  2. "" "Select Settings ' Options ' Extensions ' DataPlugins.
  
  
  3. Right-click the use of Greg_Gran_CSV, and then select Edit the Script.
  
  
  4. In line 5 of the use, the variable "Ignore" is defined as a one-dimensional two values (3 and 10) table.  These are the upper and lower values defining the range of the data channels to ignore.  To load all the data, change the value (or both) - 1.
  
  
  5. Save the use.

  As I had only a single file to test with, I can't guarantee that there will be problems with your other files - let me know if you encounter any problems or if you have any other questions.