Datasocket between office and RT PXI

Similar Questions

• I can't synchronize between Android and the Office

  I configured the synchronization of my office. I have an Android device. As near as I can understand, I must now go for the Droid and perform the routine of Sync. This will give me a code I have then (I think) put on the desk. The problem is that aid tells me to run the Sync routine since the start page of the Droid. Well, there was one when I started, now it disappeared. I can't understand how to recover this Sync routine on the droid. The help file says it must be on the start page. But when I launch Droid of Firefox, it gives me a search bar, the 'Top Sites' I visited and - downstairs - Add-ons completely useless for your section of Firefox. How can I get the Sync routine appears on the Droid so I can actually run?

  I'll post my response. Basically, the option to set up sync on my Android never reappeared and I could never find. So I uninstalled Firefox since the Droid, re-installed and the option is back. I ran the routine, got the code, put it in my office and voila!, they have been synchronized. It seemed pretty much my only option.

• Connect the large number of parameters and variables between Verstand and model of Labview

  We have an installer of dyno with a chassis PXI-E running Veristand 2014 and 2014, inertia. In order to strengthen the capabilities and timing of the Veristand, I would use models of Labview to perform tasks is not possible by Veristand and inertia. An example of this is to determine the maximum amount of a large number of thermocouples. VeriStand has a comparison function, but it compares two values at once. This makes long and rigid emissions. LabVIEW, on the other hand, has a function which words one to get the maximum items in a table in one step. I need to use Labview to 'send' the thermocouples of 50 or more to the Labview model. In addition to the variables that must be communicated between Veristand and Labview, I also need to present Labview with the threshold and setting parameters. Forums and user manuaIs understand that you must use the connector pane in Labview Veristand System Explorer mapping to expose the inports and isolated villages. The problem is that the part of Labview connector is limited to 27 I/O. How to overcome this limitation?

  BTW. I'm relatively new to Labview and Versitand.

  Thank you.

  Richard

  You can work around this limitation by putting your orders and clusters indicators. Then set the cluster to be required or recommended to indicate whether contained controls are entered or parameters, just normal.

  

• Delay between angle and entered analog on a 6221

  Hello

  my test setup consists of a (8184 current run LabVIEW RT) embedded PXI controller which uses a PXI-6221 of data acquisition. One of the outputs analog of the 6221 creates a demand for speed that is sent to a servo controller. the servo drives then the test configuration. Between the servo and the remaining test configuration, a quadrature encoder is located. Both the 6221 meters are used to measure the position of the servo (using the trains of pulses A and B) as well as the speed of the servo (frequency of A pulse train). In addition to these counter inputs, some analog inputs of the 6221 serve as well to recored the configuration of test signals.

  In this configuration, one of the analog signal has a frequency of n periods per revolution of servo (determined by the mechanical design of the test facility). But when I leave the servo turn to for example 100 rpm, then decelerate from status quo with a constant deceleration and then draw the analog signal against the measured angle, I see clearly that as long as the speed is telling, I n periods per turn (or a passage from my analog AC to zero each 1/2n towers); However, as soon as the slowdown begins, the plot gets stretched along the axis of the angle (so the plot tells me there are less than n analog periods per turn, which is impossible because it would require the mechanical destruction of the facility).
  However, I can calculate a position based on speed information signal, as I got to the second counter (by integration of the speed). When I do this for the above velocity profile and draw the analog signal against the calculated angle, I see exactly n times / revolution, no matter how fast the installation program is rotating (just the expected behavior).

  So, apparently, the speed measured is "in phase" with analog signals, while the measured angle has a "phase error. Draw the angles measured and calculated against the time tells me the same thing: the measured angle is always late (compared to the calculated angle). The period is not constant throughout the measurement; I've seen values between 30 and 170 ms within a single record. Due to this change of variable, inserting a delay for all channels, but the angle is not a great idea.

  Unfortunately, calculation of the position of the speed signal is no option for me, because the direction of rotation is changed during measurement; because speed information I have based simply on a frequency of pulse train, it contains no information management, therefore a calculated position would be unaware of the changes of direction.

  Does anyone have an idea whence thios delay and what I can do to fix this problem?
  Try a position different methods of decoding or exchanging the meter channels has not made a difference.

  Thank you!

  Hey Kevin,

  attached you will find the last block diagram (no new translation this time, since no changes have been made that require a), which includes your last suggestions (explicitly start the task of AI, remove the excess constraints) with a flat sequence structure that applies all the preparations of task to finish before the start of the first task (I know I could have achieved the same effect of intelligent routing of the signal error, but I think the code is) better readable this way).

  Without OPI, LabVIEW tends to start to have, ao and tasks of the angle of the very different moments, which (for some reason that I don't understand - we have a sample clock based calendar here, and the sample clock is run, well after the three mentioned tasks...) tends to cause delays in the order of several 10-100 ms between tasks. With the structure, this problem is eliminated.

  The Sub - VI just above DAQmx writing contains the "conduct" code that I used in the last screen shot to "serialize" the requested speeds - in this way, the table that contains the requirements of speed does not need to be rebuilt.

  The code that creates a weather channel frequency implicitly timed measure left the VI shown here in a second VI that is running on the host computer, because everything that involves a calculation and does not require any intzeraction with the DAQ hardware is better placed there (the 850 MHz on the PXI controller celeton is slower than 2 definitiely something host GHz Dual-Core system).

  The behavior you mentioned for the task "not started" HERE is what wrote using LabVIEW. I thought the block of relaxation that I had at the beginning would treat the start of the task - at least, the code like this figure repeatedly in the examples that come with LabVIEW.

  I don't really understand what has caused the problems I've had - it seems that it was the combination of the measure quickly loop iteration with the start of task based on trigger HERE, but I do not understand what are the mechanisms in the background caused the problem (too forced loop was not the cause; the same block diagram works well with an additional loop timer).

  If the solution was composed of the following steps:

  -remove the old code calculating speed, replace it with a better code out of the main loop. This allows to

  -reduce considerably the frequency of the main loop.

  -Pull the DAQmx writing out of the loop, and

  s ' ensure that all tasks are started explicitly just before the main loop starts to run.

  -Possibly remove excess constraints of the main loop.

• Difference between hp7612 and hp7610 the printer?

  Hello
  I intend to buy a jet A3 office printer.
  Can someone tell me what is the difference between hp7612 and hp7610 the printer?
  Help, much appreciated.

  Hello

  The HP Officejet 7612 include a duplex unit to print on both sides of the page automatically in the box.

  For the HP Officejet 7610, it's an extra accessory that can be purchased separately and not included in the Cabinet.

  Other than the two models are identical.

  Kind regards

  Shlomi

• Difference between static and dynamic encryption card

  Anyone tell me the difference between static and dynamic encryption card?

  Hi Rodrigo,

  Public static crypto map - identifies by the peers and traffic to encrypt explicitly. Generally used to host some tunnels with different profiles and characteristics (different partners, sites, location)

  So, when you have the information of the two peers than what policies we're going to use, what is the IP on both devices we normally use static VPN.

  Crypto dynamic map - is one of the ways to accommodate peer sharing the same characteristics (for example, several offices of branches share the same configuration) or peers with dynamic IP addressing (DHCP, etc.)

  For more information, please visit:

  https://supportforums.Cisco.com/document/12013476/crypto-map-based-IPSec...

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• Windows 7 BSOD when changing between LAN and Wifi network

  I have users to get BSODs during network between LAN and Wifi. There is not much information in the dump file.

  Any idea what could be causing this BSOD, and what can be done to correct?

  I can send the dump file if anyone is interested in looking at.

  Thank you

  Manish

  Hello

  1st thing I would do is update the card interface (wired) NETWORK and WiFI (wireless) drivers.

  Suspect also any 3rd party antivirus. Uninstall it and use MSE - free at least test.

  List of tools to clean/uninstall anti-malware programs
  http://answers.Microsoft.com/en-us/protect/wiki/MSE-protect_start/list-of-anti-malware-product-removal-tools/2bcb53f7-7ab4-4EF9-ab3a-6aebfa322f75

  Uninstallers (removal tools) for common antivirus software
  http://KB.eset.com/esetkb/index?page=content&ID=SOLN146

  MSE - free
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=5201

  ============================================================

  Resolution in Windows 7 stop errors (blue screen) - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also Windows 7)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  ===========================================================

  Check out these utilities to see if information may be collected:

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) to in a
  second or so time of the BSOD to provide more information as possible
  cause: see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows the
  Details of all application crashes occurred in your system. The information of the plant are extracted
  the .wer files created by the Windows Error Reporting (WER) of exploitation component
  system each time that an accident has occurred. AppCrashView also allows you to easily record the
  list of accidents to the text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Data transfer between PC and device

  Hello

  I need an advisor. I was wondering what would be the best way to transfer data from the PC to a connected device?

  Here's the scenario: I need to download a large amount of data from a web service. To do this, I use a small application installed on the user's PC. Once the data is downloaded and converted, the application converts it to an xml file. I would push this file or string with the XML itself to the device that will be connected through the USB port.

  In addition, the scenario reversed: I can access the PC to the device file system?

  Thank you

  Daniel

  Hi Daniel,.

  You just need to synchronize data between PC and device and device to the PC. I'm wrong?

  There are 2 ways to do it.

  (1) Intellisync APIs, (Director of office requires)-net.rim.device.api.synchronization

  (2) USB connection. (Doesn't require no Office Manager)-use streamConnection

  You will get the USBsample in samples of JDE. I guess that as the example of synchronization is in examples of JDE applications.

  Please reply,

• Site to Site VPN between 5510 and 5505

  Am trying to get a VPN site-to site and the race between a branch office and our main office. I have the settings in place, but I'm trying to determine if it's my settings or the provider DSL, Verizon.

  They have a 5505 with a static IP is connected by cable modem. Their 5505 I can ping external IP of my 5510 without problem. All the settings are correct on both sides; they reflect the same settings and yet static VPN is not launched.

  Is there some sort of CLI command I must issue to bring it?

  Also, I was wondering if maybe my 2821 prevents all VPN traffic because it doesn't have to be re - NAT'ed to the 192.168.250.0/23 and 192.168.252.0/24 subnets.

  Simply to traffic of their 192.168.40.0 in our 192.168.250.0/23 VOIP subnet subnet.

  Join a basic outline. I can provide the configs for almost everything

  Hello

  you have two instances of sequence card crypto with parameters similar (except transform set). Get rid of the rest of sequences card crypto:

  On the ASA Satellite:

  no card crypto outside_map 2 match address outside_cryptomap

  no card crypto outside_map 2 set pfs

  no card crypto outside_map 2 peers set smivpn.sorensonmedia.com

  no card crypto outside_map 2 the transform-set ESP-3DES-MD5 value

  No crypto outside_map 2 set security-association life card seconds 28800

  No kilobytes of life card crypto outside_map 2 set security-association 4608000

  no card crypto outside_map 2 the value reverse-road

  About the ASA company:

  No crypto outside_map 1 game card address outside_1_cryptomap_1

  no card crypto outside_map 1 set pfs

  no card crypto outside_map 1 set cda.asa5505 counterpart

  no card crypto outside_map 1 the value transform-set ESP-3DES-SHA

  no card crypto outside_map 1 lifetime of security association set seconds 28800

  No kilobytes of life card crypto outside_map 1 set security-association 4608000

  no card crypto outside_map 1 the value reverse-road

  Then check and capture debugs.

  HTH

  Sangaré

• Photosmart C4480 - sharing between XP and Vista problems

  I have my Photosmart C4480 connected via USB on my desktop running Windows XP. I have a home network set up between the desktop and my laptop running Windows Vista 32-bit. Sharing works files and the computers can succesfully mutually ping no problem.

  I have the printer to share in XP, but Vista does not see the printer on the network. I installed the printer drivers on both computers.

  I know that's not where he's going, but maybe someone will read it. I called the technical support and spent 57 minutes on the phone and got anywhere, not less than 40 of the 57 minutes were spent in complete silence. The only stage of the tech support rep asked me to do is to download the latest drivers on the laptop, but then me has said he did not install. After 57 minutes, he sent me an email with a link to the plug of the printer. He asked me to read him what it says beside 'Connectivity' which of course was USB 2.0. I had already tried to explain once Mr the difference between a printer wireless and a shared printer on a wireless network. Clearly, he never had the image. After reading the option of connectivity USB 2.0 for the guy, he noted that the printer could not be used on any wireless network. So frustrating. Very, very disappointed in HP technical support. Very, very unlikely that I buy another HP product.

  Someone help me please.

  I'll pass by this very detailed and try to think you don't know what you're doing so that the directions are clear and easy for anyone to understand.

  1. you must first install the printer on the computer on which it will be connected to via USB (Windows XP computer in my example). Follow the exact instructions that came with the printer for best results. The directions are simple and clear and the steps must be performed in the order that they advise for a correct installation.

  2. After you have the printer installed and working properly on your computer, the printer is directly connected to via USB, use the installation CD to install all the drivers on the computer you want to access the printer over your home network (Windows Vista computer in my example). When you put the installation provided in this computer CD click on Install or Setup or anything else that is similar in option you are given in the menu. When you get towards the end of the installation, Setup prompts you either to connect the printer to the computer or to continue and complete the installation without connection. You want to complete the installation without the printer connection.

  3. now that you have all the appropriate drivers installed on computers you want to set up your network. On the computer on which the printer directly connected (computer Windows XP in my case), you want to run the Network Setup Wizard to set up the printer share. In Windows XP, you want to click on start > my network places. This will open the my network places window. In this window on the left side, you should see a few options in the section "network management". Click 'set up a home or small business network. This will open the Network Setup Wizard. You will notice that one of the bulleted items listed for what you can do with a network is "share a printer. Follow and complete all the steps in the Network Configuration Wizard. When you are finished, your network must be configured and ready to go.

  4. now you want to turn on sharing the Photosmart C4480. Once more on the computer on which the printer directly connected via USB (once again, the Windows XP computers in my example), you want to click on start > Control Panel > printers and faxes. In this menu, you should see your newly installed Photosmart C4480 printer. Right-click on the printer and select "Properties". This will open the window properties of HP Photosmart C4400 series. You will notice that the window has several tabs at the top. Click on the "Sharing" tab, select "share this printer" and name the printer in the "share name:" text box. Do not the complicated name. I used "HP C4480" for mine. Click 'OK' to close the window and save the changes.

  5. you need to know what the IP address of the computer with the printer connected directly via the USB port, so that we can ensure that your network is configured correctly and that the other computer (Windows Vista in my example) is capable of good communicate with the Windows XP computer. On the Windows XP computer that is connected to the printer, click on start > all programs > Accessories > command prompt. This will open the command prompt window. Type "ipconfig" and press ENTER. This will show you your IP address, subnet mask and default gateway. Note your IP address. There will be a series of four numbers, separated by three points (for example 192.178.1.2). You can close the command prompt window now.

  6. now you know what the name of the computer is on the network. Click the Start button then right-click on "My Computer" and select Properties. This will open the "System Properties" window You will notice that there are several tabs at the top of this window. Select the "Computer name" tab The name of the tab may vary from one computer to another, but there will be a tab named 'Computer name' or 'Network name' or something similar. Select this tab. On this tab, you will see "full computer name:" and then to the right of that will be the name of your computer on the network (the computer DESKTOP for example). Note that. Click 'OK' to close this window.

  7. now you are done on the computer on which the printer directly connected via USB. Get on your other computer (Windows Vista computer in my example). In Windows Vista, click Start > Accessories > command prompt. This will open the command prompt window. Type "ping IP address" and press ENTER. Put your IP (e.g. 192.178.1.2) where I typed "IP address". It tests communication between computers and display the results when the test is performed. If all goes well, it will say something like 4 packets sent, 4 packets received, 0% lost. If packets have been sent but not received then you have a network problem which must be settled before the printer you will work.

  8. assuming that the ping was successful, you are almost finished. Close the command prompt window. Always on the Windows Vista computer (the computer not directly connected to the printer via the USB port), click Start > network. This will open the 'network '. Now your computer will search and display all present on your network. It may take a minute or two so be patient if nothing appears immediately. Finally the name of the other computer should appear (e.g. OFFICE). Double-click the icon above the name of the other computer. This should now show a list of all that on the other computer on the network. The common things to see here are printers and a "SharedDocs" folder You should see that the listed here HP Photosmart C4480. It is listed under the name you gave to the printer in step 4 above. Right-click on the printer icon and select 'connect '.

  9. This will open the "Windows printer Installation" window and says "connecting to the PRINTERNAME on computername. I don't remember exactly what happens the first time you do this, but it can ask you for installation and others. If so, just follow all the steps, it gives you, and he needs to connect to the printer.

  10. at this point, you are ready to go. You should now be able to open Microsoft Word or another program and print on the printer HP Photosmart C4480 from the Windows Vista-based computer on your network. The Photosmart C4480 will very probably not already set as the default printer so you will have to select in the menu of the print window in the "Printer name" drop It can open a window saying that the computer connects to the printer when you do this. After that when you click on print, your document should be sent on the network of the Photosmart C4480.

  11. If you want to set your Photosmart C4480 printer by default on the computer, it is not directly connected to (Windows Vista computer in my example), click Start > Control Panel. This will open the Control Panel window. Under the heading "Hardware and sound", click on "printer".  This will open the Printers window. You should see the "HP Photosmart 4400 series on ComputerName" icon in this window. Right-click on the icon and select "Set as default printer". After that, you should see a green and white check mark next to the icon of the printer. The Photosmart C4480 is now set as default printer on the computer, and whenever you print from any application will automatically be selected Photosmart C4480 printer.

  Hope all that made sense and solves your problems. If you please, after back and let me know if make you it work, or if you have other questions. I'll be more than happy to try to help!

• What are the differences between RT and Win 8 Pro?

  RT

  What are the differences between RT and Win 8 Pro?

  Windows 8 - this runs on processors traditional x 86 - x 64 for Intel and AMD, and the same apps that runs on Windows 7, Vista, and Windows XP.

  Windows RT - built on the same basis as Windows 8, it works on a different processor called ARM and not running programs in Windows 7, Vista, or Windows XP. In addition, it comes with Microsoft Office 2013 while Windows 8 does not work. It only comes on the new devices, in contrast to Windows 8 you can buy a license for an existing computer.

• What is the difference between Mutipoint and Multiway video calls?

  What is the difference between Mutipoint and Multiway video calls?

  They are both multi-point calls, however, Multiway is a feature that you can activate with the correct infrastructure and MCU in place, which will allow the ends without a telepresence MCU Office and integrated JabberVideo customers of degenerate transparently a point-to-point call in a multipoint call on the relevant MCU.

  See the relevant Multiway Deployment Guide corresponding to the version of software that you run on your VCS - C for more information; http://www.Cisco.com/c/en/us/support/unified-communications/Telepresence-video-communication-server-VCs/products-installation-and-configuration-guides-list.html

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Mobile subscriptions between PC and Mac?

  Hello!

  I intend to move from PC to Mac within a year, probably in a month or two. However, I know that there is so much hurt between hearing and Mac OS X El Capitan (v.10.11). I believe that it will resolve itself eventually...

  But my question is this: if I start a subscription on my PC, Adobe will honor it and help me to transfer it to the right version when it's time for me to move to Mac? I was able to maintain a monthly subscription for hearing on my PC, but at $30 a month, it's really a kind of banditry (double the price monthly vs annually? Come on, guys. Bad enough, you don't easily sell a version of office for a reasonable price, my understanding is the only one you can get is a) old and b) always at the price as high as it was when it was new).

  What I would do is start an annual subscription and then, when I need to transfer this subscription via the Mac compatible equivalent that I run on my new system. Is this possible, and if so, what version of hearing should I watch? Right now I am in a trial of CC and love it.

  Yes? Isn't it?

  -A

  I'm not a Mac user but I have seen reports that the recent correction of Apple for El Capitan has fixed most of the problems.

  With respect to the passage, I have seen this asked before and in my opinion, there is no problem to pass.  You're allowed to have your software supported on two different machines (as long as they are not used at the same time) then you can just download the Mac version when you are ready, then version désenregistrez the PC when you are happy with things.

• Difference between 'Reload' and "Reload (Override Cache)"?

  Https://support.mozilla.org/en-US/kb/keyboard-shortcuts-perform-firefox-tasks-quickly#w_navigation, what is the difference between 'Reload' and "Reload (Override Cache)"? What makes "ignore cache"?

  Reloading Web pages and cache bypass aims to obtain a new copy of perhaps obsolete or damaged files currently stored in the disk cache.
  You can do it like the first attempt if a normal charging does not seem to provide a version of a Web site or if you are having problems with a Web site otherwise.

  We usually have advice that if you have questions:

  Reload Web pages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  Clear the cache and delete cookies only from Web sites that cause problems.
  "Clear the Cache":

  • Firefox/tools > Options > advanced > network > content caching Web: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Firefox/tools > Options > privacy > "Use the custom settings for history" > Cookies: "show the Cookies".

  Start Firefox in Safe Mode to check if an extension or theme (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problems.

  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• What happened between Firefox and Roboform? FF no longer mentions RF in its modules!

  What happened between Firefox and Roboform? FF no longer mentions RF in one of its modules.

  I'm having the same problem. RoboForm contacted and they act like they have no idea there is a problem.