DCL passed to the GPIB-VXI/C

What happens to VXI boards plugged into VXI backplane when a GPIB-VXI/C (p/n 777126) receives DCL of the computer?  Do the Board reset VXI, GPIB-VXI/C doesn't know the DCL, or VXI boards ignore everything that is transmitted to their or something else happens?

Thank you!

Hello

The DCL message is a clear message of universal device that is sent to all devices on the bus and resets their conditions "power - one» For more information please visit the following links:

GPIB - IEEE 488

ArtisanScientic (Page 19 and 33)

GPIB-VXI/C operating instructions  (Pages 16 and 191)

Thank you

Tags: NI Hardware

Similar Questions

  • GPIB-VXI/C addressing

    Hello

    The manual of the Commission of the GPIB-VXI/C describes a procedure to set up the Board of Directors to use several primary addresses.  In this mode, the GPIB-VXI assigns primary GPIB addresses to message based VXI chassis servants.  Does anyone know a problem when using VISA to communicate with boards VXI through a GPIB-VXI/C, that is configured to use multiple main addresses?

    Thank you

    Hey dan,.

    When you use NI-VISA to communicate with your VXI via GPIB-VXI/C plates, you reference the jury by its logical address, and not the primary/secondary address as you would with NOR-488. 2 (also referenced in 3YG82O5N knowledge base: convert a GPIB-VXI/C program using NOR-488 function calls to the NI-VISA). So the question of multiple main addresses should not be any concern, because you are ignorant of GPIB speaking altogether and leaving the functions of NI-VISA handle it.

    Kind regards

  • When I tried to print my boarding pass of the continental, all I got was a page of small letters and numbers.

    When I tried to print my boarding pass of the continental, all I got was a page of small letters and numbers.

    There is a Bug in 4.0b12 that will be fixed in 4.0 RC, to be released next week.

  • Re: Satellite Pro L100 - couldn't pass on the card wireless with FN + F8

    Hello

    I have the same problem with my laptop Satellite Pro L100 and M70.
    I installed with new XP SP3 and installed the drivers, but I could not pass over the WiFi connection with the FN + F8 key.
    What can I do?

    Kind regards

    Csaba

    Hello

    Generally, it should be able to activate the Wlan using FN + F8 key combination.

    But before that you would use this combination of keys that you must also activate the WLan switch which is placed on the side of books.

    If you are not able to use the FN + F8 key combination, then you must install the drivers as Hotkey Utility, utilities and tools.

    On the European driver Toshiba page you will find Instructions install txt file. This file shows you the installation order correct driver

    See you soon

  • The GPIB-ENET/1000 commands reference

    Hello

    I want to control via Ethernet GPIB instruments using my own software

    FOM a Linux machine.  Do not intend to use MAX and/or any other software/drivers of OR.

    I need to be able to speak for the GPIB-ENET/1000 C commands like:

    socket = socket (AF_INET, SOCK_STREAM, IPPROTO_TCP);

    Connect (socket,...);
    Send (socket, "something",...);
    recv (socket, where_to,...);

    Is this something that can be done?

    Is there a reference of document summarizing GPIB-ENET/1000 orders

    What should I use to communicate with GPIB instruments?

    Thank you!

    Hello

    You will need a driver OR to communicate with a hardware OR. The driver you need is NEITHER 488.2 and can be found here for Linux:

    http://www.NI.com/download/NI-488.2---Linux-15.1.1/5926/en/

    This comes with a C API, so you can use any programming C environment you want.

  • I can't the arguments passed to the AWR Design environment?

    From a script Visual Basic can I get a list of command line arguments that were used to start Office from microwave or VSS?

    The command line arguments passed to the application at startup are accessed through the collection of application arguments MWOffice.Arguments . Each whitespace delimited command line argument is available as an argument object in the collection. The Argument.Value property contains the value of this argument. For example, the following script displays a list of the arguments passed to the application in the debug output window.

  • DOSBox for the GPIB support

    Hello

    New to the Commission, but have been using technologies of NI GPIB bus for five years in my business.  I am currently underway to rewrite some DOS applications based on Windows so that we can support the later operating systems, but we still have a lot of existing code written.  I have explored the possibility of using DosBox for some of these applications give a new life under Windows 7 and later operating systems.  A particular application is a work horse very versatile app written and maintained by one of our application engineers.

    Currently, I found that DosBox provides no support for the GPIB interface card.  However, I downloaded the source to DosBox and found that it was written in Visual C++.  Given my previous experience in porting applications for this platform, I am convinced that I could 'improve' DosBox to subsidize GPIB for DOS applications through a form of emulation.  I think something in the sense of a DOS application running by calling the GPIB functions which are translated by DosBox in calls in the Windows of DosBox drivers.

    Has anyone ever tried this before?  I thought that the first step would be to understand (and maybe disassemble) the code contained in libraries of objects used by these programs (QBIB. OBJ, MCIB. OBJ, MCIBL. OBJ, etc.).  I tried looking for sources for these but my research have developed dry.  Has anyone been on this path and have had better luck?  If this isn't the case, it would be possible to get more information on how the DOS driver strives to contribute to this effort?

    Thanks in advance.

    NOR-488. 2 v3.0 is now available for download:

    NOR-488. 2 3.0 - Windows 7 x 86/x 86/Vista 7 64 bit/XP/Server 2003 R2 (32 bit) / Vista x 64/Server 2008 R2...

    For the version of NOR-488. 2 version 3.0: previous versions of NOR-488. 2 for Windows has not installed BACK and Win16 is supported on Windows 7 or Vista. It is now installed on all 32-bit versions of Windows. The feature is enabled by default, but can be disabled through measurement and Automation Explorer.

  • What is the GPIB for mitigation of amplitude Spectrum Analyzer?

    Hello
    I write a test automation, and I need to do the following by programming GPIB:
    Press on AMPLITUDE balance, mitigation, 0, dB.
    The device is Agilent E4407B spectum analyser.
    I searched on the internet and made searches and cannot find the GPIB string that mitigation of the amplitude of programming orders.
    (I found all other controls that I need for this Automation).
    Actually, the test plan I put in work in the programming, said that it is no longer available via the keyboard input.
    Could it be? All keyboard commands have corresponding GPIB commands outside of it? Why?
    Maybe it's because the same effect can be achieved by a different order of GPIB? What is it then?
    Thank you!
    Tova


  • "Connection to the GPIB driver or device error".

    Hi all

    It is the first assignment, I do on this forum, so please be refrain, if I make mistakes.

    Now my problem:

    I use the NI USB2GPIB adapter and want to communicate with any GPIB device using the Simple screw GPIB.vi NOR-example.

    From the VI the GPIB - correct the device address occurs an error:

    My settings of the GPIB adapter are:

    Anyone can unmask, why in MAX, the communication is running:

    but not in VI. In the VI I get error indicator, when I try to use the function write GPIB (error bit 15 is set to 1).

    Can someone help me please?

    Sincere best wishes from good old Germany,

    z


  • will transfer data in parallel in the GPIB interface?

    Hi all

    I have two devices (that support GPIB) connected in series and connect to the GPIB interface card. These two devices have two different addresses and I use VISA module to send data at the same time. GPIB cables are connected in series, so that means it will be locked during the transfer of data to a device? I think that the GPIB transfer rates are not low (about 1 MB/s), but it takes so long to transfer 500 KB to the unit (approximately 45 seconds).


  • Get the serial number of the GPIB-USB-HS

    How can I get the serial number of the GPIB-USB-HS device programmatically?

    I worked on it. Attached simple solution.

    It is possible using the driver of VISA?

  • Slow data transfer during the reading of the GPIB (Horiba CCD 3000) device

    Hello to everyone.

    I'm trying to connect with a CCD camera (CCD 3000 - company Horiba (formerly Jobin Yvon)))

    The connection is made on the GPIB (PCI)

    The CCD device is old enough and will not support orders GPIB standard (p. ex. * IDN?)

    The problem I have is that after I take a picture, when I want to read data from the CCD

    It takes about 10 seconds before arrived it all the data to the computer

    the delay is proportional to the size of array of pixels:

    When I take the data of the entire area of the CCD (1024 * 256 pixel * 16 bits = 512kB)

    It takes 10 seconds

    When I consider 4 x 4 pixels 1 pixel (this is done by the hardware) (256 * 64 pixels * 16 bits = 32 k) it taks about one second

    What can be the cause of this kind of problem

    How can I solve it?

    Thank you

    As you say, the camera is quite old.  Maybe 50 kB/s is the maximum data rate (probably very 56 Kbps).

  • How can I configure the GPIB Tektronix tds2024 he is detected by MAX

    I try to connect the Oscilloscope Tektronix of TDS2024 to use in LabView. I use the GPIB port. I have to do something with the TDS2024? Or it should automatically detect it. I tried 2 different cables and are detected by the LabView "Measure & Automation Explorer" when connected.

    Hello

    All you have to do is plug your instrument, MAX throw if you have not already done so and scan for instruments.

    You should see the instrument listed under the GPIB device.

    Hope this helps

    Concerning

    Ray Farmer

  • ResetSys on the GPIB instruments with addresses


    Style calls (alias calls NOR-488. 2 multi-device) IEEE 488.2 use a two-byte addressing scheme where the subaddress is in the high byte.

    Help OR-488 online. 2:
    "Some of the calls to several NOR-488 devices. 2 have an address or address list setting. An address is a representation of 16 bits of the address of the GPIB device. The primary address is stored in the low byte and secondary address, if any, is stored in the high byte. For example, a device to the main address 6 and secondary address 0 x 67 has address 0 x 6706. A NULL address is represented as 0xffff. An address list is represented by a list separated by commas in addresses, such as 1,2,3.

    So, your channel should be:

  • Writing a driver for the GPIB-ENET100 in C++ based on a Linux machine

    I picked up some remains of a driver for this device and I'm trying to resurrect it for a new project.

    Basic Comms between the host and the device of the GPIB-ENET work OK, I can analyze the GPIB bus for instruments and address address Analyzer connected properly.

    But, if I try and write commands to the instrument I get an error GPIB.

    Work of communication very well by using windows OR browser based tool, so I've captured the Ethernet traffic and found several types of messages I do not recognize. He also seems to be sending messages on port 5015, but also the main port 5000.

    SO, my question: is there a document covering the interface with the device at a low level of TCP message? Alternatively, as I suspect it is the secret of stuff and I'm supposed to buy an expensive software of NOR?

    SOLVED.

    After connecting to the GPIB-ENET100 using ibfind and setting various options on board level it is essential to drop and reconnect the plug before attempting to connect and communicate at the peripheral level.

    My version of ibfind opens a socket and my version of ibonl closes the socket when it is called to set a Board/device offline.

    The driver now works perfectly.

Maybe you are looking for

  • Satellite L40w-c touchpad driver needed for windows 10

    I'm trying to adjust the settings of my new satellite RADIUS touchpad to stop the pinch zoom automatically happening all the time and whenever I go to the control panel and try the additional settings for the touchpad, it closes, saying that it is no

  • Satellite A210-19 b and a200-204 is the expandable video card?

    Hello there can someone help me I just intend to buy one of these laptop A200-204 and A210-19 b, now my question is, the video card being upgraded to example 8600gt and the processor, because in the future many games requires top video card and speci

  • replacement of lead Pavilion 15 power

    I have an a computer laptop 15-n270ea of Pavilion and I need a power cord replacement as the accountant that he lost, I've been back to PC World and they have no idea what this driver is or where I can get a replacement, they've said we had several p

  • Taskeng.exe reappears, temporarily freezing__tasks

    Hello On the computer of the fence, taskeng.exe appears asking you don't not to close... I didn't know what it was so I forced the computer fence.  Now, toolbar, site clicks, computer speed, are turned on and off whack.  I can hardly get anything don

  • Network mapped drive with hidden server path

    Hello everyone, Can you show me the code to do this: Instead, we have more than 10 data sharing server folders. What I want to do is, I mapped in any car as a name: O, P, Q, etc... I wrote a command line of mapped drive 10 network as follows: NET use