Delayed PAP2T numbering

My configuration:

SIP/VOIP software: 3CX V7

Server: Windows 2008 server + IIS7

Phones: Linksys SPA941, Gigaset 301D

Gateway: Linksys SPA-3102 & Fritzbox 7170

ATA for Bell: Linksys PAP2T

Gigabit network

I installed a PAP2T on my system of Porter Street, which is in fact an analogue phone, dialing a number when you press the button. Porter Street itself is kind of slow before he began to compose, but since I was the PAP2T to connect it to my 3CX box it takes way too long. The factor is 3 blocks away when it starts ringing in the House

When the doorbell rings the number of SIP ring group, it takes about 10 seconds or more before it starts to sound in the House (all SIP). I tried with a normal pone on the anti-terrorism Act, and I get the same deadline. Calling the ring of a system group SIp takes a fraction of a second.

The delay is obviously in the PAP2T.

PAP2T has the latest firmware. Y at - it a setting or a way to do this, go faster?

Secondly, when I ended the call and hang up, the intercom sounds for a while, which seems a normal sound when the other side closes the connection, but after about 10 seconds, it turns into one his beeper much more strong and alarming.

Who continues to go on for 15 seconds before coming back on 'hung up' State.

What is the second "alarm" and how to adjust the ATA to disconnect quicke/better?

Suggestions welcome!

Bastiaan

PS just see a strange element in the PAP2T information screen: "call 1 State: invalid ' (see below) what happens after the disconnection of the SIP system.

Full name: Porter Street

Hook status: Off

Last entry to the: 02/02/2003 17:14:37

Waiting message: No.

Last number called: 802

SIP port is mapped:

Call 1 State: invalid

2 State call: Dial idle 1

Tone: SIT 1

Hello

I think I can help you with the delay of the original composition.

Instead of dialing 802, programm "your doorbell" to dial # 802 (Yes, eight-zero-two-hash) sequence.

or change the PAP2T dial plan to include the sequence like 8xxS0 or 80xS0... to make sure that any

starting with 8 or 80 number will be dialed immediately after the 3rd digit.

I don't know what to do with the "alarming sound", but I think that it is generated by PAP2T himself.

And I see that TONE is in State "Tone: SIT 1 '... I have never see that...

Sounds to me like your Mermaid... perhaps the SIP protocol was not followed correctly?

Check the settings of the PAP2T, if there is any possibility of 'program' to SIT 1 tone and reprogram.

In my SPA-1001, I under the REGIONAL section to SIT 1 to 4 If SIT while SIT 1 reads like this:

985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)

-Reprogramming or deletion - my change the sound of the siren.

The reason why the siren sounds is command probably something invalid received SIP

Tags: VoIP Adapters

Similar Questions

  • Automatic numbering with SPA122 delay

    I have a auto-decroche (ERA, Hot-Line) put configuration in place on my ATA 122.  When I take the phone off the hook the ATA takes 3 seconds to place the call to the network.

    My dial plan entry is:

    ( P0 <:4802788500>)

    I captured debug level syslog of the anti-terrorism Act in the process.

    I'm off the hook and what follows is generated (to 100 msec) *.

    [0] off hook

    CC_eventProc(), event: CC_EV_USR_OFFHOOK (0x2), cover: 0, rating: 0, par2: (none)

    AUD_ccEventProc: event 2 vid 0 by 0 x 0 par2 0x0

    sysstatus_set_led_status_payton(), led_id: 1, statusCode:7, systemEvent: 0 x 100095

    [IVR_eventProc] evt 2 lid 0

    callEventProcTable [0] is cepIdleProc

    cepIdleProc (line = 0x1f90e8, call = 0x1f90ec, event = 9 (CC_EV_USR_SEIZURE), by = 0, par2 = (Nile))

    cepIdleProc(), lid = 0

    cepIdleProc(), pname is proxy.adam.tnltd .net

    cepIdleProc(), SYS_NOREG_CALL (0) = 0, SIP_REGISTER_OK (0) = 1

    [AUD] Get the node UCH for AUD_LINE 0 0.

    uchAllocateNode(), node 0 allocated

    [AUD] UCH node 0 attributed to AUD_LINE 0.

    uchConnectEpToNode(), linking EP FXS 1 to node 0

    uchEnableNode(), node 0 enbaled

    NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_DIALING

    SLIC_stopRing

    SLIC_startTone 1

    uchSetMute(), ACTIVATE

    Then there is a pause of 2.5 seconds *.

    Succeed together QoS

    callEventProcTable [1] is cepDialingProc

    (The call is placed).

    "' There is a 2.5 second pause between the" uchSetMute(), ENABLE ' and the 'Set QoS succeed. "

    Anyone have any ideas why the anti-terrorism Act is sitting there for so long before the call is placed?

    Thank you

    -Adam

    It could be the short Interdigit timer, the default is 3 seconds. You already tried to reduce this value?

    Kind regards.

  • numbers of

    I've just updated my iOS to iOS10 devices yesterday and while I can access my Numbers/Pages documents on all these devices, now it tells me that I can not open them on my Macbook Air.

    I haven't changed anything on my Macbook and yesterday everything was fine until I updated my iOS devices.

    I really need to access those documents on my Macbook. I mean it's life or death. Fortunately, they are saved on an external drive and in the cloud, but again, this is not the documents, is to be able to access them from my Macbook.

    Can someone please.

    Thank you

    It does not surprise me that the version of iOS in a document of numbers is not usable by Mac OS X after that iOS has been updated without a corresponding update for Mac OS X.  In the future, I suggest that you delay the update until the updates are available for the two device - especially in light of ' I really need access to these documents on my Macbook. " "I mean it's life or death."

    For "mission-critical" documents you should lag the curve a little.

    IF you have a backup of the version you should return to the one on macbook you and avoid opening this document on your iOS device at the moment.  Locate the old version by browsing your Time Machine backup, emails where you shared the removable of the document, etc.

  • Hi, I recently bought numbers in order to create a commercial newspaper. I'm the pen and paper. I need help to create a formula. A purchase column determines if the entry price column is subtracted from the price of output column or output subtracted

    Hi, I recently bought numbers in order to create a commercial newspaper. I'm the pen and paper. I need help to create a formula. A purchase column; Determines if the entry price column is subtracted from the price of output column (buy) or subtracted from (Sell) entry exit. Thank you for your help

    Hi B',.

    Buying and selling in column B

    Price of entry in column c.

    Exit in column D price

    Formula (and outcome) in column E

    If the column will B always contained 'Buy' or 'Sell', it works. It is default to a calculation of 'sell' if sale or has been specified.

    E2: = IF (B = "Buy", D - C, C - D)

    If you want to delay the calculation until the amounts entered in C and D, use this version:

    E2: = IF (OR (LEN (C) < 1, LEN (D) < 1,"", IF (B = "Buy", D - C, C - D) ")

    If you want to delay the calculation until all three ducks are on a line (B contains buy or sell, C and D contain both data), use this version:

    E2: = IF (OR (LEN (C) < 1, LEN (D) < 1,"", IF (B = "Buy", D - C, IF(B="Sell",C-D,) "" ")))

    Third version used in this table.

    Kind regards

    Barry

  • I'm trying to generate a table of random numbers 30. After each 5 readings a new vi must open and indicate to the user than 5 readings were made. and continue with the generation of the table again.

    because I don't have a sensor now, I am currently generating a table of random numbers 30. After each 5 readings a warning should be given to the user 5 readngs are completed. This cycle must be repeated. the size of the table is 30.

    Please help me, waiting for response as soon as possible.

    Once I have the transducer, I'll take 30 analog samples and then after each 5 smaples this wraning will be displayed din a new VI

    Use a while loop with a delay time representing your sampling interval.

    Use is equal to the count Terminal to see if 4, then 4th iteration = 5th sample.

    Use a box structure. The real deal will only run on the 4th iteration.

    In the case of true place a Subvi with your message of your choice in the front panel. Go to the properties of the VI window and set ' open the front panel when it is called.

    The condition to closing of attention is not given to your description.

    Consider that rather than usign a Subvi to do this, you can use the "dialog box one/two/three button" or "display message" live in the palette "user interface and dialogue."

    Please try it out and send your own VI. Do not provide us with a working solution.

    Kind regards

  • Aspire V3 - 771g - Tap/left click on delay after pressing the keys on the keyboard (some keys only)

    It is a strange problem that I have, I got the laptop computer now for a month or two, and I'm sure it makes it I got it. The problem is pretty much the title. I can't press the letters or numbers and then left click without a 1 second or so delay, I also can not left click at all if I hold down without letting go of taken, once I do the delay still occurs. I can press the keys of arrows then left click without thin delay (where left-click is delayed / disabled right click still works.) I know that the clicks get detected as the tray icon still points out the tactile/left button when it is used.

    Some information that may be required. The driver is more recent than the one on the download section for this laptop, but I had tried both and still happens. (Also tried uninstalling both and using the default Microsoft drivers but still no luck.) Keyboard supplied with no driver and no listed on downloads. Also, "Rejection of TP" is already disabled.

    Operating system: Windows 8.1 Overview 64-bit (all updates installed, yet on Windows 8 Home Premium)

    Language: English (regional setting: English)
    Manufacturer: Acer

    System model: Aspire V3 - 771 (771g on the box says do not know if this is supposed to add the g)

    BIOS: V2.21

    Processor: Intel Core i5 - 3230 M CPU @ 2.60 GHz (4 processors)

    Memory: RAM 8192MB
    Available OS memory: 8010MB RAM

    Page file: 3092MB used, 6197 MB of available space

    Touchpad

    Material, ELAN Type PS/2 Port Smart-Pad

    Driver c:\windows\system32\drivers\i8042prt.sys (6.3.9431.0, 105.00 KB (107 520 bytes), 16/06/2013 01:35)

    Keyboard

    Driver c:\windows\system32\drivers\kbdhid.sys (6.3.9431.0, 29.50 KB (30 208 bytes), 16/06/2013 01:35)

    If you need more info just tell me, any help is greatly appreciated.

    Come here for some reason that I can't edit the first post.

    I decided that I was going to send my laptop for repairs that my arrow began to act ladle which meant that I could hardly play a game at all. I thought as a last attempt I would completely reset my computer using restore integrated Windows 8 and it worked. I can now use the keyboard and click at the same time. Although the up arrow is still a little shady, I'm happy. I thought that I would be post that incase someone else had made this experience so that they can try and so know that it worked for someone else, if you've had the experience and it does not work so good luck to find a solution.

    Update - I've narrowed it down, the problem is Windows 8.1 Overview. (Which is in beta so problems are expected). If you are considering upgrading to windows windows 8.1 8 with this model of laptop, I would strongly suggest against it.

  • Addition of delay and pause to a connection string

    After the 10-digit dialing how do insert you a pause or delay adding subsequent numbers - for use on access to voicemail and other accounts requiring a login, password, etc.

    Break is a comma, the expectation is a semicolon.

  • Guide the administrator Pap2t-NA?

    Where can I get information on how to make a dial plan suitable for this device?

    Also my voicemail and other features are accessible via one * command.  However, these are all saved to the device, how do I fix?

    Is it possible that a user might choose to use the second record sip on the first line?  It would be very convenient.

    For direct IP numbering, you can also use a url?  One of these can be used with a phone shortcut?   He put the phone number of someone in and it will dial the ip address stored in the address book.

    Thank you!

    The ATA Administration Guide is here.

    Also my voicemail and other features are accessible via one * command.  However, these are all saved to the device, how do I fix?

    Disable the * xx order on the PAP2T and activate the * xx command in the numbering plan?

    Is it possible that a user might choose to use the second record sip on the first line?

    NO.

    For direct IP numbering, you can also use a url?  One of these can be used with a phone shortcut?   He put the phone number of someone in and it will dial the ip address stored in the address book.

    The PAP2T has speed dial a number on the user tab.  Is that what you mean?  If you have something in speed dial 4 you dial with 4 #.

  • Can I disable the ability to make calls in PAP2T?

    Hi all

    Could not fdind and answer online here so go.

    I have connected my VoIP (Messagenet using the PAP2T) line both my that traditional Verizon on the same Panasonic Dect phone. It works flawlessy to receive calls, but when I call dials of two devices (the PAP2T and Verizon's network fixed of course).

    I need my only VoIP number to receive calls, it is there a way to disable the PAP2T to calls (while still their reception)? This way I could use Verizon to post fixed calls US and still receive calls from the two numbers without any problem when the component and the purchase of a new device.

    Thank you

    As far as I know, the PAP2 does not provide an option to disable Inbound calls since both lines 1 and 2, but you can set up to block calls and activate DND.

    You will need to have spend you your RJ11 cord at the back of the wall and the PAP2 to make outgoing calls and receive incoming calls.

  • Numbering problem

    I have an asterisk server, and I made a number such as 10 * to compose and then I can implement some features on the asterisk.

    my phone cisco 7960 is doing well, but my Don t wrp400 and pap2t.

    any help?

    Lunatic, and what exactly happens when you dial 10 * and wait?

    You get a tone at the beginning, no beep or tone during or after you dial 10 *, no matter what tone after a wait Let's say 10-15 s (after having 10 *)?

    The asterisk indicates any that way that "feature set" mode?

    The numbering of the PAP2T plan should include one of those who, like:

    | XX. |

    (if you use "random" two figures)

    | x 1. |

    (if you use the numbers 10 * 19 *)

    | 10 * S0 |

    (if you still dial 10 * only and you want them to be sent immediately)

  • Faxing to specific numbers fails

    I am troubleshooting a problem where Fax works fine except for some numbers that always fail.

    The system is a virtual server Windows 2008 R2 with a U.S. Robotics Modem V.92 USB voice.

    Faxes are queued to the console of a fax from Windows and sent.

    There are some numbers that never receive faxes and I'd like to solve this specific problem.

    I know it might be governed composition involved - for example if the call is local or long distance.

    And some machines of the recipient fax might be older and does not send a good acknowledgment.

    In collaboration with a number that never got a fax from this system, I found that if I dial this number on my office phone, I'll get a fax at the other end but it will be 5 rings to get a response.

    This number has been verified as correct and received faxes successfully from a previous suppliers equipment.

    Is it possible that this response to the incoming fax "delayed" would cause the sender see as "the remote fax machine did not respond in time, and the call was terminated"?

    The fax modem or windows can be defined to wait longer for a response or would it be a case where the destination machine must be configured to answer after less than rings?

    Any advice greatly appreciated here... Thank you!

    Hello

    Thank you for visiting Microsoft Community.

    I suggest you to post your query on our Forums TechNet social as this question should be better there.

    Please refer to the reference to the link below to send your request:

    https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

    Hope this information helps.

  • Creating ports FXS to using Extensions on the SPA3102 and PAP2T

    Dear all

    We have a CISCO SPA3102 and a Cisco PAP2T adapter available at two of our branches. The two branches are connected via LAN. Need to configure the FXS ports on two branches to work as extensions on IP. Kindly let me know if this could use these devices or to buy the new device and how we can create plans of numbering on both devices. Reference diagram. I don't have a lot of experince work with VOIP so your support devices will be very useful.

    Concerning

    Muhammad

    You can configure direct ip, calls between the two adapters.

    The diagram shows the SPA3102 ip address is 20.20.20.5 and the PAP2T ip address is 20.20.20.10.

    I would setup the SPA3102 with a username of 2001 and the PAP2T with a username of 2002.

    When you pick up the phone attached, a dial plan of (<>[email protected]/ * /: 5060 > S0) on the SPA3102 should call line PAP2T configured with Sip Port 5060.

    When you pick up the phone attached, a dial plan of (<>[email protected]/ * /: 5060 > S0) on the PAP2T must call the SPA3102 line 1 configured with Sip Port 5060.

    I would like to change the port numbers sip on each adapter by default 5060 to something else, but that is not a requirement.

    On each line adapter configuration you need to set enable component IP: Yes, call without Reg: Yes, and call without Reg: Yes. NAT Mapping Enable must be not on each card.

  • The SPA3102 to PAP2T PSTN line

    Hello, I need to use the RTC of another building connected to the first by a link radio. I have an SPA3102 connected to the RTC and PAP2T line in the other building. the configuration I did is the following:

    On the line PSTN SPA3102 tab:

    PSTN-to-VoIP Gateway Enable: Yes

    PSTN Caller Auth method: no

    PSTN through line 1 ring: no

    PSTN to VoIP CID CID: Yes

    PSTN Caller default DP: 2

    Off hook while VoIP call: no

    Dial Plan 2: (S0<>[email protected]/ * / _address:port >)

    where userid is any user name you configured in line PAP2T configuration, ip_address is the PAP2T ip address, port is the Sip Port configured on line PAP2T configuration.

    Call without Reg: Yes

    PSTN response time: 3

    Under the tab line SPA3102:

    Turn on numbering IP: Yes

    Configuring the tab line PAP2T :

    Call for years without Reg: Yes

    Problem is I get the PAP2T call but I'm not able to do. Can U help me understand my mistake?

    Thank you

    One more thing... I have connected the spa3102 on my local network through an "ethernet" port and there is nothing plugged into the port of 'internet '. Is this a problem?

    Yes, I'd say it's generally a problem.  My opinion is that the SPA3102 was not designed/tested to make calls using the SPA3102 network premises and which could be the reason why you have audio problems.  You must be using the 'Internet' decision-making (WAN) and for the ip addresses using DHCP from the router or use a static ip address in the subdomain of your main router.

    If you change the IP addresses, you need to adjust the ip addresses used in your direct ip call configuration.   You must use ip addresses that will not change over time, if the router is restarted.  The use of router is to route the packets between the ip address used for the SPA3102 and the PAP2T.  You are generally not required to configure a path between the two addresses.

    In addition, you are running an earlier version of the SPA3102 (3.3.6) firmware. The current version of the firmware is 5.2.13 and can be download here:
    https://software.Cisco.com/download/release.html?mdfid=282414112&SOFTWAR...

    Make the above change and post a few new sip debug trace of problem calls and configurations showing the ip address changes.  The syslog posted show the title of the messages, but do not show the detail of the messages (Sip, Sip 200 OK, etc.).  Details will show the addresses by the call for audio.  Maybe a program different syslog can show detail.  Cisco has a simple windows pc program you can download here.

    https://supportforums.Cisco.com/document/36921/using-slogsrvexe-utility

    On the SPA3102 and the PAP2T System tab, you have an ip address for a syslog and a debug server.  You only need an ip address for the server to debug.

  • Communication delay between touch and keyboard

    I use a Windows 8 for laptop (ASUS) to control a robot.  The robot is controlled by a basic computer CNC program.  When I use the touch screen to respond to guests who shows the program, the robot reacts appropriately.  When I use the keyboard to meet guests, there is a delay in the response of the robot.  What happens in later versions of Windows 7 and Windows 8.   This isn't a programming problem since everything worked properly until we started to use computers with touch screens.  Anyone has any ideas about all parameters, we can change to make the keyboard respond the same as the touch screen?

    Thank you

    Mary

    I tried the boot, but it does not solve the problem.  Our programmer was able to find a workaround for the latest version of the motherboard of robot.  Those who have the older motherboard will just have to live with it.  Most won't even notice the delay, but we do not always like it.  I'll let you know if our programmer numbers on what is causing the delay.

    Thanks for trying to help.

    Mary Stephens

  • Treo 755 p - delay of shift

    I use a Treo 755 p for Sprint with Palm OS Garnet v.5.4.9.

    My problem is that my Treo has a several second delay or delay in recognition of the SHIFT key pressed (for the manufacture of capitalization).  So, even though I know you're supposed to be able to press the SHIFT key, then the uppercase letter, it does not work for me.  An up arrow appears immediately on the extreme right, but the Treo has a significant delay in the recognition in fact the shift function.  If I hold down the SHIFT key, and press a letter, I get a capital letter.  But then when I release the passage and continue with lowercase letters I can write only one or two letters when the deferred update function belately kicks in and I get a letter uppercase, inserted in the middle of my word.  Usually, it is the third letter.  Thus the words I write tend to look like this:

    An appointment with the doctor SpOck in BaLtimore

    It is very annoying because I constantly need to go back and fix/remove capital letters.  This happens by typing throughout the Treo (calendar, notes, emails).  I want to emphasize that this is not a case where the Treo between Shift lock.  There's just a capital letter based on the delay when I pressed the SHIFT key at the beginning of the word.  I have not experienced a similar problem with the Option key down (the white button on the far left used for numbers and special symbols)

    So, my questions are:

    1 has anyone else experienced this problem?

    2. is it possible to adjust (reduce) the amount delayed integrated function of the SHIFT key?  Or even remove the delay entirely so this update only works if you hold it simultaneously with another key?

    3 - is it seems likely to be a hardware or software problem?  I have add this problem with my Palm 755 p since I started using it.

    Thanks for your help.

    Then, try a reboot hot (soft reset + louder on the nav 5 lanes) to see if any software you have is originally from lag. Some things stick like a leech on the keyboard, and although they can do their job, they can create some lag when another application is in conflict with it.

    Message relates to: Tungsten T5

Maybe you are looking for