Dell Dimension 4600 with pack 1 XP does not connect to the cable modem

Similar Questions

• Linksys Router WRT160N - Wireless does not connect to the cable modem

  I installed the Linksys WRT160n router to replace an existing G router. When installed the new wireless router works, but the router does not receive a connection (IP address - look under status) of the cable modem (so no internet). When I reconnect the old router and then connect the new router, I get any internet connection through two routers (so the old dishes router the IP address that accepts the new router).

  I have configured the router N new for

  "Automatic configuration - DHCP", no need for connection, IP address dynamic, etc (as required by ISP - Timewarner)

  I tried to renewal and release IP address by the router N when it is connected directly to the main switch (the switch to connect to the cable modem). In so doing, shouldn't that assign a new IP address to the router?

  I am allowed 3 IPs from the cable company (because of the switch) and I use all three with three different internet IP cameras to each address for home security system.

  Any suggestions on why the router is not connecting to the internet? Do I need to reboot physically everything on the network, including the cable modem?

  If I understand your post, you said that your ISP gives you 3 Internet IP addresses and you have 3 cameras that use one of these Internet IP addresses.  If this is correct, then that leaves no IP Internet address for your WRT160N use - so that would explain why your WRT160N cannot get an Internet connection.

  If I misread your post, and you have an Internet IP address available for the WRT160N, you might have a problem with your modem and two WRT160N tries to use the same 192.168.1.x subnet.  To check this, follow these steps:

  (1) Please indicate addresses that use your cameras (IE before you take the test below).  If the addresses do not begin with 192.168, then erase the last half of each address.

  (2) Please indicate your ISP

  (3) Please indicate the make and exact model of your modem (not the WRT160N) number.

  (4) Please do the following test:

  Put your entire network.  Disconnect the switch (including cameras) to the modem.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT160N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

• Intermittently, Time Capsule does not connect to the cable Modem

  Capsule time bought a few weeks ago.  Barely implemented.  TC does not recognize the cable modem.  These forums to get help.  Tracking the specific set of sequence with long delays between the steps and the modem and the TC.  It worked for about a month.  Now about once a day the TC works but not internet wireless or ethernet through the CT.  If I unplug the TC and let it restart and initialize internet connection returns.  During the internet cuts I have ethernet and Wi - Fi at transport CANADA, printers, and drives on the network as well as the time Capsule backup drive and your data.  If I ever lose ethernet and Wi - Fi to TB.  In addition, the modem works fine.  If I cut the TC and to the cable modem ethernet connection I have access to the internet.

  Thank you.  All were huge last time assistance.

  If it's always the same modem... a SB6141 of Arris... There have been a number of reports of trouble with this product with Apple routers. There is no mention that in your first post a month ago, because we wanted to see if a reset of the good modem would get things works well for you.  I had the same experience as with the same exact modem you have.

  The SB6141 is a good product, and the time Capsule is as well. But for some users, these two products do not work as well together. If you call people to support for modem, they show sure to like the question time Capsule. If you call Apple, they will have a different view on things. The bottom line when you go to a support group... because it of always the other guy that you are having problems.

  At this point, the only real solution would be to decide if you want to try another brand and model of modem and keep the time Capsule, or keep the modem and try another brand of router and then connect the Capsule to the router.

  In my case, I replaced the SB6141 (I tried 3 different SB6141s previously because the ISP admitted having difficulties with this modem and some routers) with a 5341J Zoom, and did not have a single falling Internet connection since I installed the Zoom for more than a year. If your Internet service provider indicates that the Zoom is a product that is compatible with their service, you might want to try this modem.

  But unfortunately, there is no assurance that the "solution" that has worked for me will be the solution that suits you. Such is the nature of the beast, when you work with products from two different suppliers.

• Laptop with Windows XP pro does not connect to the home network. Has been fine with the Linksys router. Updated Netgear router again and now will not work.

  Improved the old Linksys G series to new router Netgear N600 - now can't connect wireless or directly with the ethernet cable. Status shows: "acquiring network address" or "little or no conectivity.  Worked through all the options of repairing typical network with no luck.  Also reset router, I tried direct cable modem & shows 'connected icon' but still does not connect to IE.  Another new computer with Windows 7 works great on this network.  What is my next step to repair?

  Use a static IP address and see what happens.

  How can I configure my static IP address?
  http://ask-Leo.com/how_do_i_configure_my_static_ip_address.html

• Problem with Windows Fax and Scan does not connect to the Internal Modem

  Just got a new Acer Aspire 5542-5416 computer laptop with Windows 7 64 bit Home Premium, 4 GB of Ram and a 320 GB hard drive. It has a 56 k modem integrated fax of like the old days, but I can't make it work. The laptop did not come with the Windows CD.

  If I open the program Windows Fax and Scan, it is not able to connect to the modem. Basically, if I click on tools > fax accounts > Add..., I get a box with 2 choices: to connect to a fax modem or connect to a fax on my network server. When I want to connect a fax modem I get a message that says: an error has occurred. Please, try the operation again later or contact your administrator. It allows me to do this then just clock OK and them I'm right where I started.

  While in Windows Fax and Scan, if I click on tools > fax settings... nothing happens. No menu settings or anything ever appears. Quite simply, the program does nothing. If I try tools > Fax Status Monitor... I get a box that says entrance exam status, ready to receive a fax. It has a blue progress bar as something takes over, but it gets about 1/100 to and never goes further or ends. There is no box, but there are 3 buttons: view details, answer call or cancel. If I hit details, I get an empty list. If I click on answer call I get an error that says that the fax service is not available.

  If I try tools > Options, general tab has only a single option box is checked: play a sound when come it to new messages. If I try to print a Word or PDF file to a fax using Fax in the printer list, I get the same box with 2 choices: to connect to a fax modem or connect to a fax on my network server, but I get the same error message: an error has occurred. Please, try the operation again later or contact your administrator.

  I've searched the Internet high and low for a solution but no luck. There is a lot of discussion about this problem, but none of the solutions work for me. If I go to Device Manager, the modem is working properly and if I click on the Modem query on the Diagnostics tab, it seems to be able to communicate with the modem very well. I tried to roll back the driver and updated again and still no luck, same problem. If I go to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Fax\Accounts in the registry, there is no subkeys under the folder accounts I can delete.

  Has anyone else had a similar problem? Is there any solution for this? I did a Windows Update last night and has not yet solve it. Thank you.

  Sorry about that.

  Here is the link:

  http://social.msdn.Microsoft.com/forums/en-us/windowscompatibility/thread/c75ae899-D05B-411D-a7f2-00fdd33b8589/

• Linksys wrt110 does not connect to the dsl modem

  I have a Linksys WRT110 router and I use a DSL modem.  I couldn't get an ipad to connect and I couldn't remember the password for my router so I pushed the reset button on the back. I'm officially the day 3 Troubleshooting cross, get new ip addresses and addressing my internet provider.  I can connect to my modem by ethernet cable to get internet on my computer and I see my router to my computer with local access but when I plug in the modem to the router can't do everything internet.   Can someone please help me solve this?   Thank you very much!!

  Try here.

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=80&login=1&app=search&VW=1&articleid=3687

• 15 - r074TU: laptop does not connect to the router

  Day sum... .my laptop (model No. 15r074TU) with window 8.1 does not connect to the router that is D-link

  I uninstalled my driver reinstalled again, but it didn't work... even if I formatted my laptop, reconfigure the router and... done with all possible measures to overcome this problem, but have ultimately failed. Please suggest ways to tackle this problem as soon as possible...

  Follow the wizards in the following forum sticky and troubleshooting.

  http://h30434.www3.HP.com/T5/notebook-wireless-and-networking/common-fixes-for-wireless-connectivity-issues/m-p/4831601#M86871

• ATI Radeon HD 4600 Series AGP Grapics card does not work since the installation of service pack of windows 7

  ATI Radeon HD 4600 Series AGP Grapics card does not work since the installation of service windows 7 pack has worked before

  Is not fully compatible with win7, some patches are available from ATI

  http://support.AMD.com/us/KbArticles/pages/CatalystAGPHotfix.aspx

• Samsung Galaxy S3 does not connect to the DELL laptop

  Hello

  I use the operating system Windows 7 Home Premium 64 - bit with the Intel processor i5-2450 M CPU @2.50 GHz. recently the past 4 months, I have observed that Samsung Galaxy S3 does not connect to the Dell laptop

  We could not see the content of Samsung Mobile in the PC. No Popup message is coming

  I tried the options below

  1. connected with different cable to the laptop, the original cable

  2. try with Samsung Kies

  Can you please help us in this regard that I wasn't sure if the drivers problem.

  We have seen the error in the mobile below.

  "Could not find the software on your computer that can recognize your device.service Pack 3, Windows Media Player, version 10 or greater, for Android File Transfer for MAC OS or Windows XP must be installed.

  You can download and install Kies on your http://www.samsung.com/kies computer to synchronize with your device data, back up the data and upgarde your device (Windows and Mac OS are supported). »

  I use Windows 7 and Media player version 12.0.7601.18150.hence was not, of course, why the Samsung Galaxy S3 does not connect to the DELL laptop

  Thank you

  Kalyan

  Hi Kalyan,

  From my research, this error message indicates that you have an old version of Samsung drivers installed on the computer.

  Several clients are faced with this question after that they have updated the version of Android to 4.3, but the version of the driver is not updated.

  I suggest you uninstall all traces of Samsung is installed in the list programs and then reinstall the device drivers Samsung from the link provided in the previous post.

  To uninstall a program see the link below.

  Uninstall or change a program

  Once you uninstall programs related to Samsung download and install the drivers for Samsung devices.

• iPhone 5 s to connect with blue tooth in the car for hands-free calling does not connect to the speaker, it works very well with the iPhone 5. How to solve this problem?

  IPhone 5 IOS 9.2 (13 c 75) I can log in my car with Blue Tooth to make phone calls, but it does not connect to the speaker. To establish the connection with the car, the procedure has been completed correctly. With the iPhone 5 it works perfectly correct.

  How to solve this problem? Is there someone who has the same problem?

  Howdy,

  Thank you for using communities Support from Apple.

  I see you try to get your iPhone to interface with the stereo in your car via Bluetooth.  For setting this up, please follow the steps below.

  If you use Bluetooth

  1. Consult the user manual of your car stereo to get the procedure to a Bluetooth device.
  2. On your iOS device, drag up to open Control Center, then press ontwice to turn on Bluetooth and turn it back on.
  3. Restart your iOS device.
  4. On your iOS device, Cancel the twinning of your car radio. On the screen of your car désapparier your iOS device and any other device. Restart your car and your iOS device, then pair and connect again.
  5. Update your iOS device.
  6. Install the updates to the firmware of your car radio.
  7. If you still not connect, contact Apple technical support.

  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon.

• All of a sudden, my dell inspiron 6000 does not connect to the internet and has an error message to see article 871122.

  New error message to see article 871122

  All of a sudden, my dell inspiron 6000 does not connect to the internet and has an error message to see article 871122. That's happened? I used it last night to check my email, and then I deleted some photos on the disk hard and this morning it will not connect. I don't really understand what happened to him because it was off last night.

  Hello

  1. you are using a wireless connection?

  If you are using a wireless connection, I suggest you to update the latest drivers for the network adapter and check if it helps:
  http://support.Microsoft.com/kb/283658

  Also check this link for troubleshooting steps:
  http://support.Microsoft.com/kb/314095

  It will be useful.

• Error - 'Auntentication with the server failed. Family Tree Maker software does not connect on the Web dashboard.

  Original title: Family Tree Maker does not connect on the Web dashboard.

  My Family Tree Maker 2009 does not connect to the Internet comes up with the message which is cannot authenticate the server, but it tells me that my version is up-to-date.  He has always worked so far? Comes with the following message if I try to do anything that involves the net.

  "Auntentication with the server failed.

  Hi HelenTL,

  You did changes to the computer before this problem?

  If you have any software security & firewall installed, disable them temporarily and check if the problem persists.

  
  Note: check to allow them back on the computer after you complete these steps.

  Hope the helps of information.
  Please post back and we do know.

• My laptop Vista with Atheros AR5007 802. 11 b / g adapter does not connect to the internet using the local area or wireless network connections

  I just bought a new router d-link wireless n for my house.  Connect my Win 7 Desktop, laptop xp to Acer and multitude of other devices, but my laptop Vista with Atheros AR5007 adapter does not connect to internet.  I tried to disable IPv6, defining the name of the network, flushing dns cache, etc..  Nothing will work.  (It would not connect to an another 802.11n router in January either.)

  I get local only on both connections Wi-wired and wireless, no matter what I do.
  I'll send this to my office that I can not connect my laptop to the internet and he does not see the other machines on the network.
  Any suggestions from anyone?  I spent hours trying to solve the problems, now completely stumped.

  OK, here was my fix:

  I tried a lot of things, but they do not work.  I downloaded a 'new' driver of HP - it turns out it was the original with the problem.  I found another one that was about a more recent months, still does not work.  I finally managed to get the atheros.cz driver for my card files.  But they do not have an installation file.  I had to search for each old file in its directory, copy it to another place (to be sure, just in case) and then copy and replace the old file with the new file in the original folder.  Fortunately, there were only 6 files, but it took about an hour and a half.  This isn't a lot of time compared to the 18 or if I was just trying to figure out the problem.  Now, my laptop connects to the internet without problem.
  I had this problem with a router "n" beginning of the year in a hostel.  The guy in the Inn told me that he had seen before once.  It's obviously a common problem with these cards (as seen on the "solutions" online) and Vista.  I'm always hating on Vista after this problem.

• I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection.

  I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection. It connects to other networks wifi very well with Internet access, is that the wireless in my house what it connects to. When I diagnose the problem, it says "Cannot communicate with DNS server (208.67.222.222)", and then under that it says: "languished network diagnostics remote hosts, but had not received a response." It connects to the Internet through an ethernet cable, but it is rather annoying pulling the cable autour. I currently have Windows Vista Home Premium. Thank you!

  original title: Internet connectivity problem

  Hello

  Now, you may need to contact the support of Panda Internet Security centre to change the settings so that wireless is enabled through it.

  Support link: http://www.pandasecurity.com/homeusers/support/

• There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.

  There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.
  I tried to connect my xbox to my computer to xbox live via the 3g router, but I was unable to. According to me, there is something wrong with the network card, since neither the wifi (wlan?) nor the lan connection seem to work.
  I harnessed connected my iPod, Xbox 360 and Nintendo DS for her, but not my computer. Please help me, what wrong with my computer?

  original title: problem with the map?

  Hi GustavTak,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?

  Try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router