Dell Optiplex SFF 3020 with two monitors

Similar Questions

• OptiPlex SFF 3020, no Communication Port Serial

  I have 10 systems Optiplex SFF 3020 and I can't get the serial to work. My rep does not know the model number of the serial port. I tried the following references, and they do not work:
  CN-Y9001
  CN-0Y73TJ

  If anyone knows what exactly reference number please answer. There is also a patch of the bios for this model that solves a problem with the com port that I applied to a system and only allows not always. Also, the internal com port is in conflict with PCI - e serial port cards even if it is disabled in the bios. Pci-series cards work for awhile but then start to malfunction. I tried 3 brands of different manufacturers. Virtually impossible to use one of these systems for what they were bought, which is printing to a printer series.

  I found myself then contact support technology guide on this issue. They had an internal bulletin to replace the will of card serial port Dell Part # 67 X 99 and that solved my problem.

• Lightroom and color management with two monitor profiles

  I have a problem with Lightroom CC on a computer with two monitors. The images on the calibrated Eizo different in Lightroom and Photoshop. I tried many things, but it comes down to the fact that Photoshop uses correctly the different profiels ICC for two screens, but Lightroom doesn't have. That is a known issue and there will be an update to solve?

  It's on a Macintosh computer.

  Lightroom has problems with Version 4 monitor ICC profiles. Make sure that your calibration than SW preferences are set to create ICC Version 2 profiles.

• Replacement 250 GB C: drive in Dell Optiplex GX 620 with WD 750 GB SATA drive by cloning. BIOS sees the drive, Windows XP does not work.

  I have 5 Dell Optiplex GX 620 desktop computers.  All are about 5 years old.  Had a hard drive failure so I replace the disks C: by secondary SATA disk cloning, disk 1 in the bios.  BIOS sees drive when Windows XP on two systems and not on the other three.  Have no idea why.  All rooms have all the updates of Windows and Dell. A bought WD Caviar Green drives.  WD has replaced three with Caviar Black readers and still does not work.

  Level 2 support WD had response which was to creat Acronis True Image WD Edition BACK boot CD for the windows version of the software, (that I downloaded on www.wdc.com), boot to a CD and had the disc I cloned then.  I wish only the support level 1 guy was aware of this utility.

• Dell Optiplex 755 MT with Windows 7.0 NO SOUND

  Hi, I have recently updated my Dell Optiplex 755 EnergySmart MT for Windows 7.0.  I get no sound from the speakers.  Can someone please?

  The windows Vista Driver for X 86 or X 64 works fine in windows 7 or windows 8 or 8.1 windows you also need the AMT HECI drivers if the system has Vpro

  http://downloads.Dell.com/pages/drivers/OptiPlex-755.html

  http://downloads.Dell.com/audio/R164900.exe

  There are more recent files that you don't need to jump through hoops for.

  One size fits all.

  Operating systems

  Windows 7 32 bit

  Windows 7 64 bit

  Windows Vista 32-bit

  Windows Vista 64-bit

  Windows XP

  Windows XP x 64

  Chipset

  ftp.us.dell.com/.../R174616.exe

  HECI

  ftp.us.dell.com/.../Intel_AMT-HECI_A02_R255437.exe

  GROUND

  ftp.us.dell.com/.../Intel_AMT-SOL--LMS_A02_R255438.exe

  Installation of the drive (by WinZip) with the file Setup.exe to Intel_AMT - HECI_A02_R255437.exe

  Download

  1. click on download now to download the file.

  2. when the file download window appears, click Save (Windows XP

  users will click Save) this program to disk and click OK.  Save it in:

  window will appear.

  3. If you want to save in: field, click the arrow to the bottom, and then click on for

  Select desktop, and then click Save.  Download the file to your desktop.

  4. If the download complete window appears, click Close.  The file

  icon appears on your desktop.

  Install

  1 double click on the new icon on the desktop, titled Intel_AMT - HECI_A02_R255437.exe.

  2. the self-extracting window appears and prompts to extract or

  Unpack in C:\DELL\DRIVERS\R255437. Write down this path so the executable (I.e.

  You can later find Setup.exe file).

  3. the self-extractor file window appears.

  4. click on OK.

  5. After completing the file extraction, if the Self-Extractor

  window is still open, close it.

  6. click on the Start button, then run.

  7. type C:\DELL\DRIVERS\R255437 in the box text open, and then click OK.

  8. follow the on-screen installation instructions.

  Description	Importance	Version	Published	Supported OS	Download
  Analog Devices ADI 198 x integrated HD Audio, v.6.10.x.5491, A02 Analog Devices HD Audio driver	Recommended	6.10.x.5491	27/09/2007	Windows Vista 64-bit Windows Vista 32-bit

• DELL XPS 8700 compatible with the monitor Samsung Syncmaster 2232 office

  HI - can anyone confirm that the DELL XPS 8700 desktop computer is compatible with the monitor Samsung Syncmaster 2232.

  Already, I have the monitor, but need a new processor unit.

  Thank you...

  Hi yydelilah,

  The monitor has VGA and DVI ports.

  By default, XPS 8700 comes with HDMI and display port.  If the system is configured with a discrete card, and this card has DVI/VGA port, you will be able to connect to this monitor.

• Some subtle problems with two monitors on Windows 7

  I used two monitors with your Windows 7 Desktop for quite awhile and I just had to replace a.  This is a problem which is probably easy to fix, but I don't know how to do it.

  I figured out which monitor, I wanted to just in front of the keyboard (the larger one) and that I wanted on my right.  The new is more.  They both work very well, but there are two problems:

  1. the office and the taskbar are in the older monitor to the right - I do not know how to move.

  2. the mouse is confused.  He considers that the monitors are in the reverse position.  In other words, when the mouse is moved on the screen to the right, I have to move it OFF THE RIGHT EDGE OF the SCREEN to enter the screen on the left.  I know that I can get used to this, but I'd rather not have to.

  Thanks in advance.

  DK

  Right-click on an empty space on the desktop and choose "Screen Resolution."

  (or Panel of-> screen-> the resolution).

  Above under 'Change the appearance of your screens', you should see two icons of the screen display.  Simply slide one on the right to the left of the icon on the left (so that they switch positions). Then press "OK" your way out.

  To select the screen that contains the task bar, select the icon for this monitor in the same screen as above and a small box should appear below the "Multiple displays" line that says 'Make this my primary monitor '.  Just check this box and OK your way out.

  HTH,

  JW

• SX2210T-touch screen with two monitors feature

  Solution found by the user ES128 for touch dual monitor.
  I've just set up a configuration of dual monitor with a SX2210T and a ST2220T on Windows 7. I got the touch features work correctly on both. As a first step, affecting either translated the entry only on the primary (the one that has been in primary school at the time), but after playing around with the settings I got work like I wanted. I tried several things, but I think that the right thing to do is go in the settings of the Tablet PC from the Control Panel window and press the Setup button next to "configure your pen and touch poster» There you will be asked to each touch screen and you're done. 2-point multitouch works on each monitor, but not both simultaneously. At one point, I went that one would be regarded as primary, and which caused the hand on a single monitor to take account of the other and vice versa. Following the same steps above again not straightened it.

  Screen touch troubleshooting.
  * Disconnect the 2nd monitor of the PC. Restart the PC so that it only displays one monitor in Device Manager. Depending on your operating system, do the following: -.
  SX2210T Driver (Windows 7 only)
  SX2210T-Touch Application
  SX2210T-Touch Cam
  SX2210T facial recognition Application (no not necessary, only if you want)
  * Test the touch screen on the single monitor feature.

  I've just set up a configuration of dual monitor with a SX2210T and a ST2220T on Windows 7. I got the touch features work correctly on both. As a first step, affecting either translated the entry only on the primary (the one that has been in primary school at the time), but after playing around with the settings I got work like I wanted. I tried several things, but I think that the right thing to do is go in the settings of the Tablet PC from the Control Panel window and press the Setup button next to "configure your pen and touch poster» There you will be asked to each touch screen and you're done. 2-point multitouch works on each monitor, but not both simultaneously. At one point, I went that one would be regarded as primary, and which caused the hand on a single monitor to take account of the other and vice versa. Following the same steps above again not straightened it.

  I have the 2220 sort of setting before the 2210 so it seems I have a gigantic version of the laptop Acer Iconia with two screens.

• Work with two monitors in Premiere Pro.

  Hello

  I'm new in the use of first Pro CC. I would like to know how you set the workspace in first to two screens. In Final Cut Pro X, there is a button where you can set the workspace to work with two screens. Where is this feature in the first? I've not found in "Workspace" or "Preferences". Please, if anyone with a tip, I'm a happy man.

  Kind regards

  Bo

  See if they help you:

  Two monitors

  Dual display

• Wacom does not not with two monitors. MacOS 10.10.4

  I hope someone can help me with this problem of Photoshop CC. I use two monitors, the left one for my tool palettes, plugins, layers, etc. and the right to display the image I am train in full screen. After the upgrade to OS 10.10.4 I now a toolbar at the top of two window (this may have been the case before, but I've never had any problems until 10.10). When I work on an image the toolbar at the top of the right screen activates and controls the keyboard and Wacom buttons do not work unless I click on the other monitor (left). Needless to say that it's a pain in the thigh. Is that what I'm stuck with or can it be turned off?

  BTW, I have a Mac Pro desktop computer.

  It does sound at least somewhat as the landmark white window behavior fixed, but I thought that this was not a common problem with the latest OS updates.  I'd be inclined to try if

  Menus, shortcuts, Lasso tool or Photoshop constantly run when using a Wacom tablet. Mac OS

• USB 3.0 docking station pro with two monitors

  I have an E550 connected to a dock, Pro USB 3.0. To get two monitors working, I got a VGA plugged into the laptop to a monitor and a SVGA from the platform to the other. I want then to the main display on the second.

  But I can drive both monitors of the dock? It is not clear in the manual if this can be done. I suppose that if I hang a HDMI VGA adapter to the dock, I can then drive the first monitor from the dock too?

  I can confirm that it works.

  A DP/DVI for dock first monitor and a DVI/DVI for the dock to the second monitor gives an extended through the two display.

• The mouse moving in wrong direction with two monitors in Vista

  my mouse passes between two monitors connected to a computer - from right to left how I changed it to move left right

  * original title - 2 monitors - my mouse goes right to left instead of left to right - how to change this *.

  "bobsamuel" wrote in message News: ef03426f-e261-4ace-a5fe-0c96460aae4b...

  my mouse passes between two monitors connected to a computer - from right to left how I changed it to move left right

  Try this:
   
  Right click on a box empty office.  On the left, click Customize display settings.  In the monitor window that opens, you should see your two monitors.  Who is that clicking on identify monitors.  Click and drag the right monitor left to the left of the original left screen and release the drag.  This should change the positions of the two monitors so that the movements of the mouse must be as you wish.
   
  Let us know if that helps.

• I have a HP h8-1010 and it is supposed to be compatible with two monitors...

  But there is only one port for monitor (DVI). I don't really understand this... There's an HDMI port as well, but is that what he meant when he supported two monitors? There are other ports, but they are covered and say 'do not remove. " Any help would be appreciated. Thank you.

  Graphics card: http://www.amd.com/us/products/desktop/graphics/amd-radeon-hd-6000/hd-6450/pages/amd-radeon-hd-6450-...

  Hello

  Your monitors are DVI - D and VGA.

  Use a DVI cable to a monitor.

  Use a DVI cable to HDMI to the other monitor.  www.pccables.com has what need you.

  Both monitors will now operate digital which is the best quality.

• (Redirected) Dell OptiPlex SFF 7020

  We just bought a Dell OptiPlex 7020 in June 2015.  He spent the diagnostic tests to include the full test, but it restarts after the message of Windows and display the colored dots (Windows 7 SP1 32 Bit) and he gets the hit text back to the screen.  Anyone know what causes this problem?  Thank you.

  Hi serta1,

  Please repost this in the help desk forum.

  http://en.community.Dell.com/support-forums/desktop/

• Problem with 5.2 and Terminal Wyse (P20) view with two monitors

  Hi all

  I'm having a problem with our Wyse P20 terminals after that we went to view 5.2.

  When a user connects first on the main screen comes on, but shuts down the secondary image and your hear Windows 7 constantly 'detect' a device - the sound when you connect a USB device.

  If I put out the Terminal voltage and plug everything is OK. It seems that if you connect at the beginning there is a problem, otherwise if the user is already "connected" and simply reconnect everything is OK.

  Any help would be appreciated!

  P.

  Hello world

  Just solved the problem with the help of VMWare.

  The problem was 'Basic Video' has been selected in the Configuration of the system > Boot > boot options - it doesn't have to be selected.

  

  NOTE: The problem with multiple monitors would happen with other devices and clients (ie: Customer View under Windows), so this is going to solve the problems on these customers as well.