Dell PowerConnect 2724 managed Mode reference works do not?

Similar Questions

• Dell 1720DN on Yosemite OSX reference works do not

  Can someone get the dell 1720DN working on OSX Yosemite pleeeeeease!

  BTY I have reset printer system reinstalled the drivers, set permissions and all the usual stuff.

  Randomly, I installed the Dell 2330DN printer drivers as the 'generic' postscript couldn't print PDF.  The Dell 2330DN printer driver works perfectly for my Dell 1720 printer.  Can someone else please give them a try and report?  PDF files and browser impressions has worked well in my test.

  Step 1: download and install the latest printer driver Dell 2330d/DN (updated in April)
  Step 2: reset the printing system, as mentioned in the previous post @AlStewarts.  (right click on the existing printer)
  Step 3: choose the Dell 2330 drivers and click Add.

  See you soon!

• Dell PowerConnect 6248 10 GB ports reference works do not

  Hello

  We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.

  So I have a few questions:

  Is the SFP + above compatible with this model of switch?

  If so, how can verify us that the ports are active?

  Here is the result of the port details:

  #show interface ethernet 1/xg3 in detail

  Port Type Duplex speed Neg Admin link

  A State

  -----  ------------------------------  ------  -------  ----  -----  -----

  1/xg3 10G - level s/o unknown Auto Up Down

  Port description

  ----  --------------------------------------------------------------------------

  1/xg3

  Flow control: enabled

  Port: 1/xg3

  Belonging to a VLAN: access mode Mode

  Operating parameters:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Default priority: 0

  GVRP status: Disabled

  Protected: disabled

  -Other - or ITU (q)

  Port 1/xg3 is a member of:

  Rule of VLAN name evacuation Type

  ----    --------------------------------- -----------   --------

  1 by default not marked by default

  Static configuration:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Port 1/xg3 is configured statically:

  Output name rule of VLAN

  ----    --------------------------------- -----------

  Prohibition of VLAN:

  Name of VLAN

  ----    ---------------------------------

  Port 1/xg3 Enabled

  Status: Disabled role: disabled

  -Other - or ITU (q)

  Identification of the port: 128.51 shipping cost: 0

  Fast port: No. (configured: no) root Protection: No.

  Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C

  Identification of the designated port: 0.0 cost of access road designated: 0

  Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0

  BPDU: 0 sent, received 0

  Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?

• DELL UPS Network Management Card firmware update is not possible in the management of inverter DELL Multi console

  I have a problem with the update of some old software on a DELL UPS Network Management card in DELL Multi UPS Management Console.

  We have a few more recent and some models with very old Firmware. The older firmware is: 01.02.0013
  I imported the update of the firmware: 01.16.0001
  If I select this version behind the inverter with firmware 01.02.0013 it is a red exclamation point.

  

  Also, I can't get to the this inverter https address.

  So I do not know how update the firmware of the network management card, please anyone who has a solution...

  .

  I got it finally working.

  I couldn't connect to the interface webGui of UPS in https on IE 6,7,8,9 and calibrated to an ssl error Firefox.
  I could not update the firmware using DELL UPS management software can. fatal error.

  I then installed Chrome, when connecting to the web GUI I ignored the warning of certificate error and waited...

  YES. The web Gui appeared, asking for the password and the Web GUI that I could install the firmware 01.14.0003

  After the update of the firmware in the webgui I was able to upgrade to 01.16.0001 in DELL UPS software Multi management.

  

• Dell 5737 MaxxAudio 4 reference works is not in Windows 10

  I installed my windows to windows 10 and now the audio sounds very different. When I clicked on the Audio from Dell settings I can't access to the setting MaxxAudio 4. How to solve this problem?

  Sorry I forgot to tell you that you need to download the Realtek card reader also. Then go into Device Manager and update drivers. I had to uninstall Realtek High-Definition Audio Driver 2 times, but now it works.  The first link is the Realtek card reader and the second Realtek High definition Audio driver. Stay in touch www.dell.com/.../DriversDetails

• Dell webcam central reference works do not.

  I have a computer dell laptop with a built-in webcam that doesn't work anymore. I have Windows 7. Everytime I open Dell Webcam Central it says "please connect a device supported", I don't know what the problem is and I can't find the webcam on device manager on my computer. It is not under what it is. Under USB controllers, but there was something that said device unknown and I uninstalled it to see if that would do anything, but no change. Please help, thanks.

  Hello

  No, you can either get the only fixed internal and if this cannot be done so using an Add - on camera.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Dell Webcam integrated reference works do not for Windows Vista in Inspiron 1525

  The Dell Inspiron 1525, I bought new 2.5 years ago.  When I got the laptop, I tried to use the webcam, but it did not work.  It shows only a screen black when the webcam running rather than capture images.  I try once more to use the webcam, and it still does not work.  Any ideas?

  Hello

  ·         Do you have a CD of the software with the laptop when you bought it new?

  You may need to install the updated release of the request for the webcam and check if that helps you to use the webcam.

  Download utilities system for the portable computer from the link below and check if that helps.

  http://support.dell.com/support/downloads/driverslist.aspx?os=WLH&catid=-1&dateid=-1&impid=-1&osl=EN&typeid=-1&formatid=-1&servicetag=&SystemID=INS_PNT_PM_1525&hidos=WLH&hidlang=en&TabIndex=&scanSupported=True&scanConsent=False

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• is there an alternative photo management system that works (and NOT the pictures)

  Y at - it another app that works better than the pictures, that we can use to manage the photos, because they took iPhoto and replaced it with pictures?  Is there a way just to import photos and save them to your computer in folders, as you would on a Windows system? And then maybe just use Picasso or something?

  You can still use iPhoto if you are eligible:

  Terence Devlin

  April 14, 2015 14:21

  Re: Iphoto's gone? I want to go back!

  Go to the App Store and check out the shopping list. If iPhoto is there then it will be v9.6.1

  If it's there, then drag your existing iPhoto application (not the library, just the app) in the trash

  Install the application on the App Store.

  IPhoto is sometimes not visible on the shopping list. It may be hidden. See this article for more details on how to view it.

  http://support.Apple.com/kb/HT4928

  A question often asked: Will I lose my Photos if I reinstall?

  iPhoto, the application and the iPhoto library are two different parts of the iPhoto program. So, reinstall the application should not affect the library. BUT you should always have a back up before doing this kind of work. Always.

• Pavilion Slimline lock up in sleep mode-fan works high not lights up unless I pull the power cord 1

  New HP Pavilion Slimline desktop 400-314 - mode 'sleep' sometimes cause to lock the computer, the power light is on, the fan runs at the top.  Only way to unlock the computer is to hold the power button for 5 seconds.  I wait 15-20 seconds, then press the power button to wake it up.  Immediately the computer restarts to the top with solid power light and the fan turns at the top.  The only way to break this vicious circle must first pull the power cord to the rear, wait 30 seconds and plug it in again.  This time, when I turn on the computer it goes off just fine.

  Is this a BIOS problem?  Please help as I don't have that much hair left.

  * Solved * Finally!  After 8 grueling days of pain staking agony and incessant attempts to fix this thing, I finally solved my problem.  I spent countless hours on the phone with HP support and nothing resolved.  That is: the problem with this computer locking up and sending the fan at high spin was due only with external speakers. When you reset the power system disconnected to boot the system, he would normally go for at least half a day before locking up.  I discovered that the speakers are older than 15 years. It's funny, these speakers worked fine on a desktop HP 2004 previous Pavilion running on Windows XP.  Now, it's static build-up that caused my death or something else?  As far as I know, it's that I'm a happy camper using headphones with a new system of HP that finally works.  Thank you to everyone who made suggestions.

• How to check the HP management agent is working or not?

  Hi all

  I managed to install HP on ESXi 4.0 management agent by following the steps mentioned in http://h20000.www2.HP.com/bizsupport/techsupport/SoftwareDescription.jsp?swItem=MTX-25f06077ad5541f5a962dd2a69 & lang = to & cc = us & idx = 1 & mode = 4 & . Can you please suggest a simple method to make sure that the agent is running? as mark some system info or see the details in the user interface.

  C:\Program VMware vSphere CLI\bin & gt; vihostupdate.pl - root of the server test - username - password test-bundle FTP://testftp/pub/Depot/HP-esxi4.0uX-bundle-1.1.zip - install - bulletin bulletin1 bulletin2

  Please wait install the fix is underway...

  The update has been completed, but the system must be restarted for the changes to be effective.

  C:\Program VMware vSphere CLI\bin & gt; vihostupdate.pl - root of the server test - username - password test-bundle FTP://PDP-BLR-Suite/pub/Depot/HP-esxi4.0uX-bundle-1.1.zip -query

  -

  ---

  IDS bulletin-

  ---

  -

  ---

  Installed-.

  ---

  Summary.

  -

  ---

  HPQ - esxi4.0uX - bundle - 1.1 2010-01-29 T 15: 00:13 HP ESXi Bundle 1.1

  Kind regards

  Oumou khairy

  : +: EMCPA, RHCE, VCP4, VCP3.

  The easier option:

  In VC hardware status tab search HP smart Array storage. The default virtual circuit support HIS HP, need suppliers CIM HP to show this option.

  Anlother method is to stable wbemcli in a linux box, (in Ubuntu, you get using #apt - get wbemcli * installation command, or download a compilation of the sblim packa, redhat has in their CD or you can get from sourceforge.net) and try the following query.

  wbemcli ecn - nl - noverify ' [https://root:[email protected]/root/hpq[email protected]/root/hpq].

  the above query should list a bunch of classes.

• Narrow ARM of SPI VI reference works do not for me LabVIEW 2009.

  I use LabVIEW 2009 Embedded for ARM in collaboration with the Council of development of LM3S8962 and the MCP3008 10 - bit ADC chip. I'm trying to use the base screws of SPI to communicate with the MCP3008 - see the attached excerpt from VI to my current attempt. I can initialize the SPI reference, read two bytes of data from the ADC, but when I try to close the reference, the application crashes. If I am the narrow ARM of SPI reference VI in a diagram to disable, the program terminates normally, and I get to see my two bytes of data printed on the OLED. Any ideas?

  Thanks in advance,

  Stuart

  Thank you!

  Who takes care of the immediate problem. I really appreciated the quick response!

  Stuart

• BlackBerry Smartphones Media Manager doesn't work does not correctly after the installation of update

  I have a 8110 and put to level to the desktop 5.0 version.  Since that time, the Media Manager does not recognize the 8110 put pics on computer.

  What should I do to correct this?

  Thank you.

  There is no need of Media Manager.

  You can transfer files directly:

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=BlackBerryDesktopSoftware&message.ID=...

• Display of stand-alone ActionScript 3.0 language reference works do not

  I am unable to see the majority of the standalone downloadable version of the ActionScript 3.0 language reference.

  The document in question: http://help.Adobe.com/en_US/FlashPlatform/reference/ActionScript/3/standalone.zip

  (link caught in http://www.adobe.com/devnet/actionscript/references.html()

  To replicate:

  1) download the file of http://help.adobe.com/en_US/FlashPlatform/reference/actionscript/3/standalone.zip.

  (2) expand the zip file, open the folder that results and open the index.html document in your web browser.

  (3) choose any filter link you want from the options on this page. Note that packet filters and the class in the header display constantly "getting data from server...". »

  4) click the Classes link in the header at the top.

  Result: The list of class displays only momentarily, and then mask completely.

  It would be great if there was a way around the filters entirely. There seems to be several missing items in the download, for example en_US/shared/ahpods/AHPod.js.

  I'd settle for a PDF of all-in-one of the reference.

  Difficulty of Joe... Ward on wire http://forums.adobe.com/message/3958537#3958537 :

  Unzip the reference in a folder named "langref" - there is a bug in the Javascript code that filters the contents of the page based on your selections (in these controls that say 'retrieve data from the server... »). The code looks really like a folder named «langref» (I'm sure that the engineer who did this thought that it was a quick hack that he or she could clean it up right now...)

  Thank you!

• JQuery UI reference works do not

  I tried to integrate the widget menu jquery UI in an application today and have a bit of trouble. I read the documentation here http://docs.oracle.com/cd/E37097_01/doc/doc.42/e35125/app_comp001.htm#HTMDB29030 and followed these instructions of the documentation to include the menu widget (replacing the 'menu' to 'tab' below):

  <link href="#IMAGE_PREFIX#libraries/jquery-ui/1.8.22/themes/base/minified/jquery.ui.tabs.min.css" rel="stylesheet" type="text/css" />
  <script src="#IMAGE_PREFIX#libraries/jquery-ui/1.8.22/ui/minified/jquery.ui.tabs.min.js" type="text/javascript"></script>
  

  When I run the page I get 404 errors for these two files. Any ideas why these files are not be found?

  Earl

  jQueryUI Menu Widget is not a part of version 1.8. See the relevant documentation 1.8: Widgets: jQuery UI 1.8 Documentation

  When you go to jQuery UI , you'll always see the latest version, which would be 1.10.

  Another way to inspect what you have available in the apex is simply download the apex installation files. You can view all of the pictures folder and its contents in it - and that's the biggest part of the download anyway. I keep a download with me all the time – quick and easy.

  Use the menu on apex.oracle.com, you need to include the libraries jwho of a CDN or by downloading the files to static files of the apex under shared components and add the relevant links on the page.

• How to access the management of VLANs with a different virtual LAN (Dell powerconnect 6224)

  Hello

  DELL powerconnect 6224 reference.

  I want to access the management of a different VIRTUAL LAN VLAN.

  The management of VLANS is 100 of VLAN. not the routing

  My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.

  Thank you for your help on the command line

  The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.

  See you soon