Dell Powerconnect 5424 connectivity issues

Hi all

I recently got a Powerconnect 5424 switch I would add to my current setup. My current setup is:

Router (Linksys RV082) (has a few connected devices)-> concert switch 8 ports unmanaged netgeear (has other connected devices)-> switch 5 ports netgear (on 2nd floor rest of devices).

I would like to put the 5424 in place and Switch 8 ports.

So far, I was able to put the IP Address of the switch and this via the console, and I can connect 2 devices and make them communicate. However, when I plug the switch into my router, nothing will be on the switch. Cannot ping it, cannot ping the router when the devices are connected to the switch...

Not very well where to go from here, or what to watch.

Thanks in advance!

Other options would be switchport access or switchport general.

Console (config) # interface ethernet g1

Console (config-if) # switchport General allowed vlan add 1

General mode is a hybrid of the trunk and access.

Console (config) # interface ethernet g1

Console (config-if) # switchport access vlan 1

Tags: Dell Switches

Similar Questions

  • Problem with the Dell powerconnect 5424

    Hi all!!

    I got 2 switch dell powerconnect 5424. I set them up with an IP and everything goes well (for now).

    But when I connect a switch on the network I have this message:

    1 January 2000 00:01:07 % STP-W-PORTSTATUS: g21: STP Forwarding State
    1 January 2000 00:01:27 % STP-W-PORTSTATUS: g21: STP Blocking status
    1 January 2000 00:01:27 % STP-W-LOOPBACKDET: g21: STP loop detection.
    1 January 2000 00:01:42 % STP-W-LOOPBACKDETRSLV: g21: fixed STP loop detection.

    I do not understand because there is only the network (port 21) and my computer that are not connected so no possible closure.

    There is the same problem with the second switch, so I think this isn't a hardware problem.

    Someone has an idea to help me?

    Thank you


  • Reference Dell PowerConnect 2824 remove connections, odd led models

    Hello

    We are noticed on some of our Dell PowerConnect 2824 switches that our devices are connected to the switch suddenly disconnected.  Our devices are a network of small size with the switch, where we connect up to 12 devices and use DHCP to assign IP addresses to the devices.  We also monitor the network with a Windows laptop.  We have also seen times where the switch itself seems to be restarted and shows amber LED light up successively from left to right on the top row of ports, then return on the bottom row.  I confirmed that we use version 1.0.0.45 software for the switch in question.

    We have also seen situations where all, except one device remains connected, but when trying to reconnect to the device has fallen, it seems that the switch seems to completely ignore the device regardless of the port where we connect to the switch.  We tried other cables, but the problem persists.  It's the kind of behavior that I could wait if the MAC addresses are not unique, but all of our devices have all custom MAC addresses.

    Another issue is that we use a very short lease period of one minute.  I don't know if this will get us in trouble.

    If you need more specific information, I'll try to answer your questions.

    Thank you.

    Bob

    Hi Bob,

    If it happens on several switches it is probably not a problem with the hardware switch. It could be a matter of Spanning Tree where it lacks a Hello and due to the lease really short DHCP is originally from the port to close before it can restore a link. You can try to turn STP or enabling quick link on the ports for end devices.

    Why do you have the DHCP lease on so little time for only 12 aircraft? It would add a lot of network traffic. You can try and have some machines on static IP and see if it still falls these ports.

  • Connection SAN Dell PowerConnect 6248

    Our switch in our network is the Dell PowerConnect 6248. This switch has a SFP module.

    I was wondering if I could use this module to connect my SAN [activeRAID 32 TB of storage active destocking] and have access to the storage as a network or NAS drive Bay.

    To be more precise I'll be plugging the controller [HBA] San to the SFP module on the 624 of Dell PC via a cable Fibre Channel LC.

    I'm new to SAN configuration and look for the best solution to access the storage on my network.

    Everyone has implemented a San with the SFP Module before; If that set up your look like?

    Fibre channel and ethernet/IP are not compatible protocols without another device that can translate. The 6248 has no support for FCoE. There are switches that support both they are called network switches convergent or unified, although generally the traffic is still separated.

  • Able to display the output but cannot send and entry on powerconnect 5424

    Hello

    I am configuring a PowerConnect 5424 switch to connect to my network as one of the distribution switch. When I explain on my network. its very basic as we do not have to any VLAN managed or any other complex implementation.

    When I boot the switch connection with putty via a cable series, I can see the output of the switch where I can't enter anything. I tried three different emulators of terminal that did not work at all.

    What can be the reason, how can I do this because I just want to set up an IP address so that I can connect to switch and monitor ports... etc?

    Hello!

    Thanks for the reply. Well, he had no problem with the cable or unit, it is the laptop that I used. It's no wonder that my previous Dell switch has failed. I tried it on another laptop and it worked like charm. I managed to configure the switch too.

    Thank you!

  • Reference Dell PowerConnect 6024F get mac by ip with arp and more option

    Hello in the DELL community.

    I hava a little question, and hoping to find some answers here ;) I'm writing a small script, and in this script, I need to get the mac address is to link to Ip address of the ARP command. I am using telnet to connect to DELL. But the show arp command displays a lot of information, a huge list of ip. I tried to analyze, with the '' option and press etc., but it's a very slow procedure.

    Two main issues:

    1. how to get the mac address and link it to the IP by ARP command

    2 how to get rid of the option ''. I mean show cli without

    I thank the of to get answers.

    P. S.

    ===========================

    Switch: Dell PowerConnect 6024F

    # See the worm
    SW version 2.0.0.19 (date may 5, 2008 time 16:33:30)
    Start the version 1.0.0.13 (August 13, 2003 time 15:28:31)
    HW version 00.01.64
    #

    Show arp? -> watch only

    Show arp

    Terminal Server? -> watch only

    Terminal Server
    history

    He might have an OID you can pole for this info. all the OIDS are in the MIB that are included in the download for the firmware.

    www.dell.com/.../DriversDetails

    If you do not find one in the MIB, you might try a SNMP walk on the switch to see if you can identify an OID that will provide you with this info.

  • Mac pro wi - fi connectivity issues

    I have the same problem, it seems that many people have with Wi - Fi connectivity issues.  I just bought the Macbook Pro in December 2015.  My computer goes to sleep and when I open the hood it looks like I'm connected to wireless, but I'm really not!  I'm going to websites, and they won't open.  I disconnect my wi - fi and reconnect and sometimes it works, but sometimes I actually have to restart my computer.  For the moment, at the end of the day I'll stop my computer, then restart the morning I guess.  It sometimes seems to lose its connection during the day too, I guess because he falls asleep.  Very frustrated.  Just got this computer in December and have had this problem since I use the computer out of the box.  I was told it's because I haven't had my update of El Capitan, did, but it wasn't the problem.  Technical support suggested a few other things we also went through and those who did nothing either.  Don't know what the problem is or how to solve this problem, or even if I can if so many others have this problem.  I think it's a matter of Apple and the wish that they would be admitting the problem and try to find a solution.  Apple of love, but right now quite disappointed.  Quite expensive computer for issues that I am.  I went from a Dell for an Apple thinking it was the best thing since shirt pockets, hmmm...  I don't think it's any problem with our modem, wireless, router, etc., because we have other laptops, iPads, iPhones in this House and have NO problem.  So, I hope that everyone is not running out to buy new routers and modems because no doubt this is the problem at all.  PLEASE APPLE, DO SOMETHING TO FIX THIS!

    Hold down the Option key while you click on the wireless icon in the menu bar. You get a screen similar to the following:

    what you get for channel and mode PHY?

    What CISOS or the signal strength?

    What emission rates?

    very important and how many other networks do you see?

  • Dead circuit 2 on Dell Powerconnect 5448

    13. 24 (circuit 2) ports on my Dell Powerconnect 5448 died without lamps regardless of the connection. Is it possible to have the unit repaired or replaced circuit?

    Thank you

    SE C.

    The switch has no easily replaceable parts on it. In this Youtube video, you get a glimpse of the inside of the switch and see that everything is everything on a single card.

    http://bit.LY/1QeQ4O4

    It sounds like a hardware problem, but you can try to reflash the firmware on the switch.

    http://Dell.to/1p46zT1

    If the switch will exhibit this behavior, then it should be replaced.

  • Reference Dell PowerConnect 3524 - "SW3P_callback_rx_frame - arp - scrapped intervention."

    Hello everyone.

    The company I work for, I test switches to see who is good and who is bad. I've already marked the switch in question as 'bad' for these mistakes - but I've never seen this error before. My colleagues have not either. Therefore, I ask the community what kind of error is what it means and whether it is potentially fixable.

    My device is a Dell PowerConnect 3524. He is currently out of warranty.

    What I did: I have deleted the startup configuration and then run the Setup Wizard. I put an IP address, gateway, and password. The rest, I left the default values. This configuration works on all switches that I have ever tested, including this model, so I think that this configuration is not serious.

    Then I plug in an ethernet cable in all ports and the other end into a very small 5 port switch that also has other trendy items above, the phone and my main computer. They all get internet, I don't think that there is a problem.

    I plug another cable in another port of the switch and the other end in a laptop sitting on top of the switch (my laptop test).

    I start ping the local firewall and run it with the "-t" parameter so it does not stop.

    It is fine for about 5-10 minutes usually. I can trade ports and others and she'll pick up ping soon and do what it is supposed to. After plugging into the wrong port, (7 or 8), I get the error "SW3P_callback_rx_frame - intervention arp - put the scrapped." and cannot pass traffic. PuTTY shows that the connection is established and transfer, but the ping is not possible.

    I am only an intern, this switch is not vital and will be sent to the "cemetery" and all my business done with switches will be. I am just curious to know what it is. Anyone know what it is and what could be done to solve the problem?

    Thank you for your time!

    I couldn't find any relevant information on this error message. With errors that occur only on specific ports and a new configuration, it really sounds as a kind of material error. Will there be another message that accompany this message? If you haven't already done so, re-flashing the firmware of the switch can help ensure that the message is not caused by an image that has become corrupt.

    http://Dell.to/1XmQxPU

  • Dell PowerConnect 6248 10 GB ports reference works do not

    Hello

    We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.

    So I have a few questions:

    Is the SFP + above compatible with this model of switch?

    If so, how can verify us that the ports are active?

    Here is the result of the port details:

    #show interface ethernet 1/xg3 in detail

    Port Type Duplex speed Neg Admin link

    A State

    -----  ------------------------------  ------  -------  ----  -----  -----

    1/xg3 10G - level s/o unknown Auto Up Down

    Port description

    ----  --------------------------------------------------------------------------

    1/xg3

    Flow control: enabled

    Port: 1/xg3

    Belonging to a VLAN: access mode Mode

    Operating parameters:

    PVID: 1

    Capture filtering: enabled

    Acceptable frame type: no label

    Default priority: 0

    GVRP status: Disabled

    Protected: disabled

    -Other - or ITU (q)

    Port 1/xg3 is a member of:

    Rule of VLAN name evacuation Type

    ----    --------------------------------- -----------   --------

    1 by default not marked by default

    Static configuration:

    PVID: 1

    Capture filtering: enabled

    Acceptable frame type: no label

    Port 1/xg3 is configured statically:

    Output name rule of VLAN

    ----    --------------------------------- -----------

    Prohibition of VLAN:

    Name of VLAN

    ----    ---------------------------------

    Port 1/xg3 Enabled

    Status: Disabled role: disabled

    -Other - or ITU (q)

    Identification of the port: 128.51 shipping cost: 0

    Fast port: No. (configured: no) root Protection: No.

    Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C

    Identification of the designated port: 0.0 cost of access road designated: 0

    Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0

    BPDU: 0 sent, received 0

    Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?

  • Reference Dell PowerConnect 3048

    Hello!

    I have a Dell PowerConnect 3048 I want to use it on my home network. For now, my network is small, but as the days pass, he has grown. The problem, I'm running, even after the request of Google, is that I have a hard time finding a way to be able to configure this option. The switch has the power, and I also have the DB - 9 to Ethernet cable from the console.

    For this particular option, the console port is the business end of DB-9 while the end of Ethernet connects to what I presume, a computer. Again, the problem is when I connect the cable from the console of the computer, the switch and use HyperTerminal or PuTTY, I can't speak to this switch. I don't understand what I am doing wrong?

    A lot of reading and watching videos, I understand that some switches have a console, but on this particular switch Ethernet port, it doesn't have such a port. Please guide me on how I can talk to this switch so that I can get configured for my home network.

    Kind regards

    The original cable was a db9 to db9 cable. You can try another cable, like a db9 to usb.

    The switch's default IP address is 192.168.0.1. Then you could try a telnet connection too. See that you have a better success rate.

    www.dell.com/.../ArticleView

  • How to access the management of VLANs with a different virtual LAN (Dell powerconnect 6224)

    Hello

    DELL powerconnect 6224 reference.

    I want to access the management of a different VIRTUAL LAN VLAN.

    The management of VLANS is 100 of VLAN. not the routing

    My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.

    Thank you for your help on the command line

    The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.

    See you soon

  • Update Firmware on Dell PowerConnect 3548p

    Hi all

    I have dell Powerconnect 3548p and I want to update via telnet and I was wondering what the commands are as I tried those on the CLI manual.

    I made a connection with success of my tftp to the switch and vice versa.

    I am aware that this is possible through the web management, but I would like to know how to do this via PuTTY.

    Thank you

    You can update the firmware and boot code by using the command copy. Here are the commands that will be carried out.

    Update the boot Code and firmware

    Console # copy tftp: / // image

    See the boot to console #.

    Start console system #.

    Console # copy tftp: / // boot

    Thank you

  • How to change the time that stacks convergence on Dell PowerConnect 8164

    I have create a pile between two switches Dell PowerConnect 8164.
    But I want to know if I could change the time it takes for converges converges moment between them, I want to say... I have remove all the stacking cables (so no connection between no switches) and connect them then... something between 3-5 minutes for the complete convergence.
    Is there a customization here?
    Kind regards!

    There is no option of customization on the re-convergence of a battery.  It is basically kicking a restart of the operating system on the box.

  • reset the password on a Dell PowerConnect M6220

    Hello, I'm trying to reset the password on a Dell PowerConnect M6220.  Can connect to the CMC via the https Web page, I don't see how to do it from there.

    Then I'll try to plug a USB serial cable into the console port and reset the password via a console session using teraterm but when I do that all I get is a white screen.

    Parameters of the series are:

    Cable: The Null Modem

    Bits per second: 115200

    Data bits: 8

    Parity: None

    Stop bits: 1

    Flow control: no

    Any ideas on how I can access telnet access to the device to reset the DDT successfully

    Thank you

    Kevin

    You can connect to the console port internal to the switch via the CLI of CMC

    Telnet to the CMC, then connect switch-a1 (a2 or b1 etc. etc.)

    This will give you the > invites, so either delet the startupconfig and recharge it, or put into you own username and password - remember that you can set on the schema of the interface of the band or band in slecting the appropriate interface

Maybe you are looking for