DELL PowerEdge T300 boot CD

Similar Questions

• Dell PowerEdge T300 ntoskrnl.exe missing or corrupt [MS]

  Dell PowerEdge T300
  To: Win server 2003 32-bit st
  pOWEReDGE Expandable RAID Controller BIOS
  LSI 2007
  PERC 6 / i adapter
  6.0.3 - 0002 Pack FW

  It operating system starta no segnalando immediatamente di installare una copia del file ntoskrnl.exe

  Diagnostica no notes problemi hw

  It is properly Marin raid:

  1Protection drive found on the host adapter
  1 virtual drive managed by the BIOS

  Per ripristinare it Sop ho tried a con un disco di install di w2003 startare my non vede he raid e non ho a disposizione I driver (f6).

  Buongiorno,

  pilot of the it by it e perc6i controller he following:

  http://downloads.Dell.com/FOLDER97889M/10/DELL_MULTI-DEVICE_A07_R211422.exe

  Speaking saluti

  Manual

• (Redirected) Dell poweredge 1950

  I have a dell poweredge 1950 server that was given to my school and I am trying to install windows server 2003 on it, but an error saying:

  Setup did not find any hard drives installed in your computer.

  Make sure that the hard drives are powered on and properly connected to your computer, and that any hardware configuration of the drives is correct. This may involve a diagnosis provided by the manufacturer or the installer running

  How can I fix?

  I also tried to boot Ubuntu from a usb key and that no longer works.

  I also said to update BIOS or Flash the Bios but I don't know how to do and do not know if that'll fix it.

  I want to just get to the top and running, it can be Ubuntu or windows everything is easier.

  Any help would be greatly appreciated

  Better for this post in the Forum Server-PowerEdge, here:

  http://en.community.Dell.com/support-forums/servers/default.aspx

  Bev.

• Cannot install ESXi 5.5 on Dell PowerEdge T620

  Hello

  I have a Dell PowerEdge T620 server and I want to install VMW VSphere Hypervisor 5.5 on that.

  I tried 2 ways above, but they are not successful.

  Track 1:
  -Start with DVD integrated with server
  -Config for RAID 5
  -Choose the option "VMW ESXI 5.5 HDD"
  -Error: "the provided raid configuration is not supported" and force reboot me.

  Track 2:
  -L' boot using an ESXI 5.5 CD-ROM
  -Follow the step on Setup screen.
  -Scan disk step HARD to install the process is too long too long scan...

  I hope that an idea can help me solve that.

  Thank you!

  You use the ESXi Dell installation?

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?DriverID=20VNP

• [Solved] Dell PowerEdge R720: Error when will United Nations datastore in VMware ESXI 5.1.0 [SD]

  Buonasera,
  HO a Dell PowerEdge R720 fuori co, build 799733, non riesco ad add a datastore not found da dipped 1.8 to.
  Durante FICS 'add a storage' seleziono disk/Lun, VMFS5, per poi was "Current Disposition of the disc" al, nella casella vedo the con dei locali brain table a couple of partizioni di default.
  Dopo few minuto di attesa mostra una finestra in cui VSphere loses the e outdo if sta tentando di ricollegare.
  Can I try a ricollegarmi senza esito, dopo some UNAMET outdo e di nuovo attiva

  This is the che viene say error:
  Call "HostDatastoreSystem.QueryVmfsDatastoreCreateOptions" of object "ha-datastoresystem" on ESXi '10.2.99.36' failed.

  He guardando Dell Disco local delle partizioni noto:
  1 XXX DatastoresAndVolumnes.PartitionType.0xde not found...
  2 Win95 FAT32 LBA 2.00 GB

  No Yes di cosa is... If my alla fine ho need understand di causa e come lo spazio image Add.
  Allégo ibm_db del disco inquisito: naa.6848f690edfa310018e37ce915ef3fcf

  Come posso lo senza riavviare storage server add it?
  The partizioni in questioned are best-known boot di durante FICS? Oppure posso eliminarle?
  CI sono dei comandi specifici per creare he vmfs volume?

  Grazie in pre-empted by it vostro aiuto

  Salve,

  No we can aiutarla a software level. It forum dedicated to e a soli problemi hardware.

  If dovra rivolgere o al supporto Vmware o a terze aziende.

  Speaking saluti

• Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode.

  Hi Sir,

  Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode after upgrading the RAM to 64 GB.

  Arrangement of RAM is made 4 our 16 GB of RAM on 2 channels. I get no error message about the RAM configuration. It is booting in safe mode but not start in normal mode, his hanging during windows startup.

  Please give me guide to solve this problem.

  I thank & regards

  Ramanantsoa D

  Thanks for the reply.

  My version of windows is 32-bit Windows server 2003 Enterprise Edition Service Pack 2.

  Although I have not tried switching/EAP, I will try that and get back to you.

  And again something I have an idea of the installation of windows server 2008 R2 Standard version on this server, it will support? Please let me know Chris.

  Thank you.

• configuration dell poweredge t610

  Hi all

  I hope you guys can help me with the following.

  I have this server in the office: dell poweredge t610.

  Configured with raid 5.

  Two of your hard drive has failed, so I replaced the. After the replacement, used windows. Boot. I installed a fresh installation of windows 2008, after a reboot once the installation is complete. I know that the following message:

  Uncompressing Linux... ok, booting the kernel.

  System initialization, please wait...

  To start replication, please insert your disk replication.

  Replication will begin once the system has started.

  I don't have a disk of replication.

  How can I solve this?

  "Missing only the drivers for interruption of system controller. can we all now who are these? »

  You must install the chipset:

  ftp.dell.com/.../INTEL_5500-5520-CHIPSET-SOFT_A03_R295077.exe

  "Also the program called to control the raids of the web?

  It's called OpenManage Server Administrator:

  ftp.dell.com/.../OM-SrvAdmin-Dell-Web-WIN-7.3.0-350_A00.exe

• Server Tower Dell PowerEdge T110 II

  Hello

  For server Dell PowerEdge T110 II Tower

  If I choose

  Microsoft (r) Windows (r) Server 2008 x 64 R2 SP1 Standard Edition(5CAL), FI, S-Chinese [included in price]

  as the operating system, why then I an error like

  The version of Microsoft Windows Server 2008 R2 SP1Operating system was to have 40 GB or 80 GB maximum hard Drivepartition. To solve the problem, please use the links provided.

  choose which hard drive configuration?

  Kind regards

  Once you go to the section "Installation of boot (to Windows (r) OS only) Partition" and select 40 or 80 GB partition error you are referencing disappears.

  Let us know if you have any other questions.

• Install.VGZ fails in ESXi 4.1 install on a Dell Poweredge R710

  I have a cluster of ESXi 4.1 six-host running on Dell Poweredge R710.  They start from a USB key connected to an internal USB port.  I did at least 12-20 installs on the same hardware without problem.

  When I try to re - install on the single ISO ESXi 4.1 host via the iDRAC, the installation fails when loading install.vgz with the error message: "Booting: MBI = 0x000100c0, enter = 0x0040024a.

  I studied the two codes and the only suggestion that I get, it's that my hardware is not supported (specifically that my 32-bit processor is not supported).  I do not have a 32-bit processor, so I know that I can surrender.  I downloaded the CPU VMware ISO (file:///C:/Users/pguarco/Downloads/VMware-CPU-Compatibility-e.x.p-160658.zip) compatibility, and my CPU meets all requirements.  Previous installation of ESXi host crashed for unknown reasons, where the re - install.  It is possible, that there is a hardware problem.  Any ideas on how to limit this problem?

  you are doing the right thing. only thing I could thing is bad ISO, (Please make sure that the checksum is correct). and the worst case material PE firmware update.

• Dell PowerEdge 2950 P2V problem

  Physical server:

  Dell PowerEdge 2950

  Windows 2003 R2 Standard x 86 operating system

  Sheet music:

  Dell - hidden partition

  C: BONE

  D: Data1

  E: Data2

  F: Data3

  G: data4

  vSphere ESXi 4.1 (under license)

  ISCSI SAN

  vCenter Server

  I tried on cold hidden server with boot CD, but received the error "unable to determine the operating system invited."  Looks like that I don't have the driver for the Dell raid controller in the boot CD.

  I decided to go with the hot P2V using the plug-in for VirtualCenter.  I stop the SQL server service and disabled the firewall disabled the anti-virus tools.  Only two partitions (C and G) on the physical server must be in the new virtual machine.  So, I've selected partitions C and G and has increased the size of the drive at a time.  I made sure not to install the vmware tools and unchecked the option reconfigures.   The P2V conversion was successful.   But when I went to start the virtual machine, it starts with the 'VMWARE' logo and restarts immediately.  Restart the virtual computer so fast I can't even in the BIOS unless I hit the key several times.   I did the clonning with the hidden partition, but with the same problem.   There are no BSOD or any indication that the virtual machine cannot find the vdisks.   Called in vmware support.  They used webex for an hour, but could not fix.  Asked me to send in the logbundle.

  I HERE it if someone tell me what I am doing wrong?

  Thank you

  Another option is to install the Standalone Converter 3.0.3 on the PowerEdge, stop all services and performing the conversion.

  André

• Usb device ESXi 4.1.0 through material passtrough on Dell Poweredge R510

  Hello.

  I am trying to use one of the four usb ports on a Dell PowerEdge R510 inside an ESXi 4.1.0 260247 host for a XP Prof invited. I have the following PCI devices:

  With each of the devices ID 00:1 a. 0 00: 1 d: 3 comments XP correctly will not start. When I attach the 00:1d.7 device boots comments, but then there is a problem with the device driver. I tried the chipset drivers for W2003 from dell (http://support.euro.dell.com/support/downloads/download.aspx?c=de & cs = debsdt1 & l = a & s = bsd & releaseid = R269378 & SystemID = PWE_R510 & servicetag = & os = WNET & osl = GE & deviceid = 17195 & devlib = 0 & typecnt = 0 & vercnt = 2 & catid = 1 & impid =-1 & formatcnt = 0 & libid = 27 & typeid =-1 & dateid =-1 & formatid =-1 & source =-1 & 396483 = starts) , but no luck.

  I know that there is now a direct usb support in ESXi 4.1, but my usb device is not supported through this new feature.

  In addition, I'm looking for a PCI Express RS232 serial card that works on this server equipped with passthrough for a XP guest.

  Thank you

  Michael

  Try to ignore this ridiculous list, it's a bad joke for devices on the external bus like SCSI and USB.

  I've successfully used the USB feature in 4.1 for a device not on the list (in fact, he was a device of type modem/serial port), more precisely a key entropy of Simtec.

  So anyway, try your device with the USB function before mingling with the much more fragile PCI passthrough feature.

• VMware ESXi 4 on Dell PowerEdge 2950 CDROM missing in virtual machines

  Hi all

  I installed VMware 4.0 on my Dell PowerEdge 2950, and everything moved very well. I had the ISO image from the support site on the website of VMware and Dell. I installed both with the same problem, once installed, the CD-ROM will not be displayed in any virtual machine, I create.

  I changed the boot parameters, the order of the boot, played with the BIOS settings, and no matter what I do, when I start the virtual machine and open a console window and try to connect on the CDROM, a message displays saying that the device is disconnected.

  I have reinstalled Windows on the box, went to the site of support of Dell and applied each update BIOS patch and firmware of the box. Including the one for the TEAC CDROM, which is in my box.

  Anyone had this problem before? If so, how should I do? I really need this works quickly. Without a CDROM, I can't install software such as SQL Server and others.

  Kind regards

  Michael Lange

  I assume that you have added a CDROm for virtual machines?

  You then specify "logged in/connected to the power on" in the settings of VM page? (I know it's usually obvious.. .but I did it very mistaken once this week.. .accidentally added the CDROM to the VM wrong.)

  What OS your virtual machine is running and you have the installed VMTools?

  If issuing a VMtools install on a windows host, it works, then the Cd drive works as ESX uses the virtual CD Rom to install the tools.

• Card LaCie esata PCI card on windows 2003 server Dell poweredge T410 error code 10

  Hi guys, I am trying to install a new card Lacie esata PCI card (http://www.lacie.com/products/product.htm?pid=11217) on windows server 2003 on Dell poweredge T410. Windows detects the card and install the driver, but then, it shows an error code 10 "device Can not not started. I tried the update, uninstall, reinstall, adding Lacie driver CD through the "Hardware Wizard', chaning PCI card slot by 4 to 1. But nothing has worked. So please let me know if you think that there is a fix for this solution. Thank you

  Hi Rlap,

  The question you have posted is related to Windows Server and would be better suited to the TechNet Discussion groups. Please visit the link below to find a community that will provide the support you want.

  Windows Server Forums: http://social.technet.Microsoft.com/forums/en/winservergen/threads

• Ventole Rumorose DELL PowerEdge 850

  Buongiorno,

  avrei need di UN preventivo relativamente all'intervento di a vostro tecnico per sostituzione del corpo che sono diventate ventole molto rumorose knew a Dell powerEdge 850 service tag 93F5F2J.

  In attesa di a vostro riscontro Patu speaking saluti

  Marco

  Buongiorno, OTS will in privato a ' manage the request email.

  Grazie

  Marco

• Ordine brain DELL POWEREDGE R720 - disco rotto

  Buonasera,

  I wanted to get one offer by the di UN SAS price disco da 7.2 krpm 1 TB 2.5 "by server of he DELL POWEREDGE R720 nostro.

  Grazie.

  Saluti,

  Buongiorno,

  Può acquistare disco it a questo link

  Accessories.euro.Dell.com/.../Category.aspx

  Marco