Dell Precision 690 memory risers

Similar Questions

• Dell Precision 690 workstation several hard drives

  I have a Dell Precision 690 and I am trying to connect the hard drives in the right order. The documentation says they must go into the HARD drive marked locations on the motherboard, but they do not work. The only slots that work are the SATA slots. I tested five SATA drives but I can only get three to work on three SATA slots instead of four locations of HARD drive and slot extra SATA as the book said to do.

  I tried which helps the controller under the BIOS: has no significance if it is enabled or disabled. I determined that AHCI is unable to be activated, it must be ATA.

  In the end, I need to have five total drives. Four in the slots in the HARD drive and the other in the SATA slot. (Which will be for operating system 1 SATA and SAS RAID 4). I realize that the HDD_0, 1, 2, 3 locations are to use SAS/SATA but I can't take too much work.

  In addition, I don't ' know if this is important or not, but he has Windows XP Professional x 64. BIOS A05 and I know an update is A08, I did do that yet though.

  Anywhere I can find that material assistance would be much appreciated.

  -E.Avalon (help).

  Yes, there are three ports labeled SATA (0,1,2) and four ports labeled as HARD drive (0,1,2,3). The manual says to connect hard drives in HARD drive ports, then in the SATA ports. The first two SATA ports are for additional optical drives and the last port is used for a fifth hard drive.

  I got in touch with several people in technical assistance from Dell and eventually find the right driver to install.

  Because I don't have the OEM disc that came with the computer, I was doing a new installation of a Windows disc. I needed F6 (third party drivers) to activate the HARD disk ports until the installation has taken place. (And honestly I don't remember what the file was immediately.)

  The AHCI could not be activated because the discs I have are Serial ATA disks and in the BIOS, there is a choice between ATA and AHCI.

  The problem is solved and I feel like I could do a test on this computer and become a technician for her.

  -E.Avalon

• A power of 1000w Dell Precision 690 United States will work in the British system

  I want to order a replacement power and found a Dell Precision 690 1000W ND285 power in the United States, I know that this system works this power but wanted to know if I ordered it from the United States to be shipped to the United Kingdom (England) it will work here or is there a voltage difference that will blow/effect it?

  The reason why I ask this is that I repair my friends Precision 690 power because it starts not as it should be because it has the dreaded 1-3 and power button flashing continuously orange. I usually get it going again for him leaving on the supply cable of the day after / for a few hours, but the problem comes back finally after some closures, so not a solution.

  His system has 32 GB of RAM, a processor my171 mother board 2 Xeon QuadCore 5355, a Nvidia Quadro 4800 graphics card and 4 SATA drives and 2 DVD r/w drives all sitting in the appropriate ports.  I tested it on and all the way to no disk no ram, but even in this case the problem may occur intermittently.  I don't know that his power relatively maybe even a little somewhere? but I've looked and looked and left with the feeling that his power.

  but the only one I can find that is affordable is to the United States, the price they want to pay in Germany, I could buy a car for.

  American food will work in my UK machine?

  Thank you.

  Hugh

  (Just note that happened in (general Hardware, Audio, video) I hope this is the right category, if not my apologies.)

  hughhill

  Yes, it should

  Input 100-120 v or 200-240 v, output: 1000w Max, reference number: ND285

  Model number: N1000P-00, Ref number: NPS-1000AB a Rev: 06

  For Precision 690 microtower systems

  Connectors:

  1 x 24 - Pin ATX power connector Standard ATX Standard 1 x 20-pin power connector, power supply ATX Standard 1 x 12 pin connector, ATX Standard 1 x 8-pin power connector, 2 x PCI-Express, 4 x Mini 2 power connectors pin power connectors, adapter 1 x 6 - Pin power connector.

  Before using the power supply, check that the voltage is set at 240v. There should be a red toggle on the power switch, to set the voltage, if there is no switch, then the power supply is auto switching.

• Dell Precision 690 workstation

  Hello

  I'm trying to find the instructions/manual for my Precision 690 WS.  I am trying to install a DVD player, but can't find a way to remove the cover in the front of the drive bay that you want to insert the disk in it.  If you know how, I would appreciate your help.

  Thank you

  aak740il

  Hello

  I'm trying to find the instructions/manual for my Precision 690 WS.  I am trying to install a DVD player, but can't find a way to remove the cover in the front of the drive bay that you want to insert the disk in it.  If you know how, I would appreciate your help.

  Thank you

  aak740il

  See pages 73/121 owner's manual here:

  http://downloads.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dell_precision_workstation/precision-690_user%27s%20guide_en-us.PDF

  Bev.

• Question OS/Hardware Dell Precision 690

  Hello

  I have a 690 w a single dual core running Windows 2003.  It has Mo MY171 rev A01.

  I put processors Dual quad X 5300 inside?

  What are the chances of getting work Windows 2008?

  What are the chances of getting work Windows 2012?

  Will be one of the Socket 771 X53XX Xeons in there?

  I put processors Dual quad X 5300 inside?

  Yes: http://www.dell.com/downloads/global/products/precn/en/spec_precn_690_en.pdf

  What are the chances of getting work Windows 2008? What are the chances of getting work Windows 2012?

  Good, but this is not guaranteed. It takes the server processors does not mean that it will support server operating systems. The details have never wanted to be servers - workstations. There is a good chance that you can load a server operating system and have it work perfectly, but there is also a chance that some of the equipment is the only quality work station and don't have drivers that will work correctly.

  Will be one of the Socket 771 X53XX Xeons in there?

  -What? Adapt? Work? 771 all fit, but not all of the 5300 X may work. See the data sheet above. 5300 X are supported, but not necessarily all of them. The data sheet says "up to" 1300 MHz and 2x4MB / 8MB, which means that if all processors X 5300 exceed these specifications, they may not work (unless the support has been added specifically through the BIOS update).

• My Dell Precision Workstation 690 cannot boot from the drive - I need help

  My Dell Precision 690 Workstation is unable to boot from the CD Rom what's happening, it's that when I boot it (revision of BIOS A05) and I go to the Boot menu and boot from the CD Rom it says floppy seek failure. I don't know how to solve this problem and I don't have a floppy drive installed. I have installed windows but it gives me just a blue error screen then please help

  Thanks in advance

  Hi Yolega20,

  Well, the DVD drive seems to work otherwise? You have all other bootable discs you can try, such as the Dell drivers and Utilities disc?

• Precision 690 MY171 rev A00 mobo - hearts Xeon 5300 series

  Hello

  I know that this subject has been discussed in the past, but I am having a hard time finding an answer for my exact situation.  My Dell Precision 690 runs the rev MY171 A00 motherboard on rev A08 bios.  It currently has a single processor dual core Xeon 5150.  I want to upgrade to dual quad core Xeon 5300 series processor.  I've seen youtube videos and discussion with rev A02 MY171 boards that run the 5300 series, but nothing to confirm if the version A00 will run them.

  The rev A00 motherboard BIOS A08 MY171 will work two Xeon 5300 series quad core?

  Thanks in advance for the help!

  Today, I received my processor Xeon X 5355 to four hearts by post and installed in on my MY171 Rev00 on bios A08.  No problem during the performance of the processor.  I took out the battery from the motherboard for 2 minutes before relocation and commissioning for the first time.  BIOS immediately recognized the processor.

  I'm running window 10 and initially he saw only 2 carrots.  I went into MSCONFIG and made some changes on the STARTUP, the Advanced Options tab, you should uncheck 'Number of processors' and restart.  After that, the OS will see all 4 cores.

  I intend to run identical to the second X 5355 processor, but am waiting to get a second heat sink before a fall.

  Hope this helps others seek to upgrade the 690.  The two processors cost me a total of $20 on ebay.  Also got 16 GB RAM DDR2 PC5300 (8X2Go) for this computer for $10.  Computer will work great for $30 worth of improvements.  I still feel like they need SSD to run faster.

• Problems of precision 690

  I have Windows 10 technical preview on my 690 and I can't. I try to run the Dell technical support. It gives me this:

  "We are unable to recognize the service tag detected through our analysis. Please restart the scan or contact technical support for assistance. »

  What is happening with it? I entered my serial number manually and also used the software to detect it. Any suggestions?

  Thank you

  It worked! Everything is off the Execute Disable bit: in Bios/security and Win10 loaded on the Dell Precision 690 with no problems. Thanks for the idea! {:>) I guess I'll have a spare MB now at least. Was only about $30 with installed 3 GHz proccessors on Ebay. Thanks again!

• Additional memory for Dell Precision M4600

  Hello people, I need your help once more, my laptop is a Dell Precision M4600, come without webcam, dvd - rom, 2 x 2 GB ram, without fingerprint reader, intel core i5 - 2540M, the memory of two banks in the lower side works fine, two banks of memory under the keyboard come covered, I removed the cover and try to use , but when put memory in this Bank, the laptop does not work, power on but not the video, the witness of hard drive and wifi is turned on and battery is flashing. I am doing wrong?

  Thank you in advance.
  Daniel.

  Hi Daniel,.

  Precision M4600 memory configuration is based on the processor. All 4 memory (DIMM) slots will work if the computer has Intel Core i7 Quad Core or i7 Quad Extreme processors.

  Only 2 slots DIMM will work in configurations with processors Intel Core i5 or i7 Dual Core. Because your computer has processor i5 - 2540M, only the primary DIMM slots (bottom) can be used.

  Please come back for any clarification.

• Failure of Dell SAS 5/ir Firmware update - Precision 690

  I tried to update the firmware on a precision 690 Dell SAS 5/ir and it failed.  I now get the following message when I boot.

  Could not load the LSI Logic Corp. MPT BIOS

  Lack of MRT BIOS 02 h met (XXh, XXh or XXh) PCI adapter

  Fusion-MPT Firmware error code 0706 h

  This machine is the way out of warranty, but works very well.  I have here do anyway to reflash the firmware?

  In case someone else has the same problem.

  Unzip the FIRMWARE. CPE and run the MPTUTIL, then load xxx.fw, then load xxx.rom

  Solved the problem in five minutes

• Dell Precision Workstation 690 with Win7-64 final. -3 TB hard drive?

  I have a Dell Precision Workstation 690 with Win7 64 Ultimate installed.  I want to use a 3 TB drive.  How will I know if the SATA controller is compatible with a 3 TB drive. ???

  How to know what Board motherboard or the SATA controller module I have?  When the computer starts first the BIOS detects SAS 5 Host Bus HBAO (?)  I forgot the exact name of disks while he finds the SATA drives.

  Greetings Tenoc,

  Thanks for posting your question on the community.

  The integrated SAS controller that comes with the Precision 690 name: 1068 LSI PCI - X - SAS 3 Gb/s controller. He is old enough, at this stage, and I'm sure that it only supports MBR (limit UP to 2 TB).

  You can try adding in a newer card, like the Perc H710. Not sure if it works or not. There are various other cards you might try there.

• x 8 connection distance MXI causes conflicts with my on my Dell Precision T3600 PCI slot

  Hi all

  The easiest to say is that I am migrating from a x 4 MXI explicit connection to an x 8 MXI express connection and when I do I get an error on the motherboard which is unable to load the single PCI slot.

  Error in WIn7 64 bit Device Manager reports a yellow exclamation point

  Device "Intel (r) 82801 PCI Bridge - 244 properties"

  The error listed in the device status box: "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Unfortunately, I need this slot machine to run a card calendar to conjucton with PXI hardware. There is no anomaly when I used the x 4 connections with virtually the same loadout except for one Exchange a PXI-5122 (x 4 config) to SMU 5122 (x 8 config).

  If I leave the MXI PCIe card in but do not connect to chassis PCI slot SMU (and the fine card appear.)

  If I remove the PCI card into the slot, the error still occurs.

  I swapped the x 8 card and NVidia graphics card without success (the 16 x only two slots).

  I photographed the reader and removed the H310 Dell PERC RAID card and charged the RAID array RAID integrated Intel C600 and still no change.

  I have updated BIOS to A07 to latest A08.

  I updated the Intel Chipset at the latest on the Dell Web site.

  I guess that I just wonder at this point if someone is able to run a x 8 MXI express at SMU with a Dell Precision T3600, T5600 or a T7600 chassis.

  PC - Dell Precision T3600

  Windows 7 Enterprise 64-bit SP1

  3.2 GHz Xeon 6 core (E5-1650) w 16 GB of DDR3 memory

  Reference Dell PERC Raid (x 8 PCIe) H310 / C600 onboard Intel RAID

  Nidia Quadro 600

  2 x 1 TB SATA drive (mirrored)

  SMU Rack - OR 1082

  Slot 1 - SMU - 8381

  Slot 2 - OR SMU 5122

  Slot 3 - NOR SMU 5442

  Housing 4 - OR 4 to 6 TB RAID NI 8262 x MXIe

  Housing 5 - PXI 6733

  Housing 6 - PXI 6733

  NI MAX report is attached as a text file.

  After much work by NI Applications Engineer Kyle K, this problem has been resolved.

  I'll post the solution to this PC dependent problem here, just in case it will help others in a similar situation.

  It seems that Dell sometimes uses one default BIOS quite restrictive on the number of PCI bus in these (and other). By allowing several PCI bus, you will be able to list all the devices in the sacrifice of some memory available for OS 32 bit running on 4 GB of RAM. No problem for me because I'm under 64 bit OS.

  Congratulations to Kyle even if he has not posted here yet for him give real congratulations.

  Greg

• Dell Precision 490 CPU Upgrade

  Hello

  My Dell Precision 490 currently runs 2 x Intel Xeon 5130 (Woodcrest) 771 socket LBA.  The Intel Xeon 5160 next would be compatible with my system. My mobo is ODT031 / 5000 X of Chipset / 6321ESB Southbridge.

  Server Intel Xeon 5160 3.0 GHz dual core Socket 771 CPU SL9RT 4 M/1333 64 - bit

  Type of CPU / microprocessor
  Server market segment
  Family Intel Xeon 5100
  Model number? 5160
  CPU HH80556KJ0804M reference numbers are a microprocessor tray/OEM
  BX805565160A is a microprocessor in a box
  BX805565160P is a microprocessor in a box
  Frequency? 3000 MHz
  The bus speed? 1333 MHz
  Clock multiplier? 9
  The package 771-land Flip - Chip Land Grid Array (FC-LGA6)
  1.48 "x 1.48" (3.75 x 3.75 cm)
  Socket Socket 771 (LGA771)
  Introduction date 26 June 2006
  Price at introduction $851

  S-spec numbers
  Production processors of'RE / QS
  Part number QLUF QOXI QTII QXQT SL9RT PLATE SLAG9
  BX805565160A +++
  BX805565160P +++
  HH80556KJ0804M +++

  Architecture / Microarchitecture
  Core microarchitecture
  Bensley Platform
  Cranberry Lake
  Glidewell
  Core processor? Woodcrest
  Review of basic? B0 (QLUF)
  B1 (QOXI)
  B2 (QTII, SL9RT, SLABS)
  G0 (QXQT, SLAG9)
  CPUIDs 6F6 (SL9RT, SLABS)
  6FB (QXQT, SLAG9)
  0.065 micron manufacturing process
  Data width 64-bit
  The number of cores 2
  The number of threads 2
  Floating Point Unit integrated
  Level 1 cache size? 2 x 32 KB instruction caches
  data cache 2 x 32 KB
  Level 2 cache size? 4 MB of shared cache
  Multiprocessing up to 2 processors
  With MMX technology
  SSE
  SSE2
  SSE3
  Extended Memory 64 technology (EM64T)?
  Virtualization technology?
  Execute disable bit?
  Power mode low features HALT
  Extended halt mode
  Stop grant mode?
  Enhanced SpeedStep technology?

  Thermal/electrical parameters
  Nucleus of V? 1V - 1, 5V (B2 Stepping)
  0.85V - 1, 5V (G0 stepping)
  Minimum/Maximum operating temperature? 5 ° C - 56.5 ° C (B2 Stepping)
  5 ° C - 60.7 ° C (B2 Stepping)
  5 ° C to 65 ° C (G0 Stepping)
  Maximum power dissipation? 130.83 watt
  104,84 watt (continued)
  Thermal design power? 65 watt

  Notes on Intel HH80556KJ0804M
  The bus frequency is 333 MHz. Because the processor uses Quad bus Data Rate effective bus speed is 1333 MHz
  Part BX805565160A includes 3U + active / passive thermal solution 1U
  Part BX805565160P includes the 2U passive thermal solution

  I tried an Intel x 5365 and it remains as a CPU not supported. I'm under revision of BIOS A08. There is sauce more involved magic, such as a general release BIOS rev no?

• (Redirected) Precision 690 starts

  I have 8-9 years old Precision 690 with dual Xeon 3160, dual nVidia Quadra 4500 graphics card, double SCASI Hitachi 150 GB, hard drives searched. Computer worked fine until he ceased to start up.

  At the start, it does not show with Bios A 06 Dell logo, as it should.

  This does not suggest that the problem is with the motherboard, boot hard drive or maybe the operating system?

  Any suggestion will be appreciate.

  With our thanks.

  Dragan Mikki

  Best of this post in the Hardware Forum general office, here:

  http://en.community.Dell.com/support-forums/desktop/f/3514.aspx
   
  Bev.

• Windows 7 works with the Dell Precision 670 computer?

  I have a Dell Precision 670 workstation. It came with Windows xp x 64. I later upgraded to Windows Vista Ultimate x 64. The only problem I had at the time is that the host SCSI controller is not recognized by Vista. I used the XP x 64 drivers for the scsi controller and worked well. I want to upgrade my Vista x 64 to Windows 7 x 64. Everything else does? Doing a job? The Windows 7 Upgrade Advisor reports the controller scsi HD as an unknown (just under the name Vista Upgrade Advisor).

  The HD controller is an embedded controller the Adaptec SCSI HostRaid (Ultra320). I was not able to determine the model # of the controller.

  A representative of Micorsoft with what I discussed this said as a general rule, if your hardware works with Vista service pack 1, you're usually good to go.

  On the Dell website, it lists the 690 as working with Windows 7. It is a similar job, but I can't say with certainty how similar.

  I saw him last night. I'll look over it.

  Dave.