Deployment of ISE in the wireless infra WLC (single 1240AG Access Point)

Similar Questions

• Deployment of ISE from the beginning

  Hello

  Looking at the overall deployment of ISE within our Organization.  If I understand correctly, that we start mode only (current) monitor and here we extend first wired and wireless later (by Cisco use case).

  I am trying to understand what is our next step.  In my opinion, we have a lot of work ahead of us:

  Configure switchports to take dot1x supported

  configure certificates of ISE and case

  configure clients wired to use the dot1x

  Configure the devices that cannot dot1x for Mac.

  Review connect ISE to ensure we weren't anything like that on the wired side

  activate the policies for a wiring

  (similar process then for byod and wireless)

  I have difficulties to find a doc that explains all the above and the order in which should be carried out, if this is the best I have.

  Someone there the config docs or recommendations on how to do this, go smoothly?

  Thank you

  JonM

  Cisco has published a series of 'How To' guides. You will find them all here:

  https://communities.Cisco.com/community/technology/security/PA/ISE

  Search offers by Thomas Howard, for example: https://communities.cisco.com/docs/DOC-68149

  In addition, Kat McNamara tell a good series in this same space:

  https://communities.Cisco.com/people/katmcnam/content

• Is it possible the default value to a specific Access Point, where several AP?

  Hi, first of all, I want to thank you for taking the time to read my post. To give you a brief description of my system, I'm running a T60 with windows XP operating system.  I have the latest Dial-up connections, version 5.02 installed.   I installed the most recent drivers wired / wireless, wireless, I use: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62875for wired, I use: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-67829

  Wireless security: WPA

  Problem: Here to work, we have multiple AP in the building (Cisco equipment) at least 5, there is an access point located right above me, when I try to configure a new profile in the dial-up connections, and specify this AP over my head right, he will accept... but when I try to connect, it connects to a different access point not the one specified in the profile.  The result is a signal very very low.  Workaround for this currently is looking for all the AP VIA the button "Find Wifi" in dial-up connections and specify that it connects to a right above my head, the result is almost a 100% signal strength.  Is there anyway that I can get this access point which is located just above me to stick on the default profile?  I tried to create the profile several times but it always default to an AP really far.  Thanks again, E.

  Ericsobig, welcome to the forum,

  I don't know if you've tried? If you click on the configuration of the profile advanced settings, you can enter the MAC address of the access point preferred, with alternatives.

  It may also be that the AP is too narrow, and because the response interval is too short, it loses the connection, I had this experience.

• Wireless adapter is missing! Access points could not be found.

  Hi guys! I need your help on my ASUS laptop running Windows 8. The wireless adapter had disappeared. I can not connect no.w at access points or find either. I'm just usingLAN cables to connect to the internet. I tried to solve this problem through update, but nothing happens. I check the Device Manager and bluetooth wasn't there. Please see image for your reference. Answers are highly appreciated. Thank YOU YOU in advance. Godspeed.

  Hi Ele,

  Thanks for providing the details.

  Click on the link below, select the operating system as Windows 8, click on wireless in the list of drivers. Download the driver here.

  Tools & driver

  http://www.ASUS.com/Notebooks_Ultrabooks/X451CA/HelpDesk_Download/

  Let us know if you need any other help.

• Connected to the wireless network but no Internet access?

  I recently got a Packard bell easy note laptop ts shows its connected to my wireless connection but when I open Internet explorer, it can not display any web page, anyone know what could be the problem? It connected correctly to my last connection Wireless at home.

  Hi,

  You did changes to the computer, before the show?

  Method 1:

  Run the network troubleshooter, and check.

  Using the troubleshooter from network in Windows 7

  Method 2:

  Consult the following link:

  "Internet Explorer cannot display the webpage" error in Internet Explorer

  Warning: him reset Internet Explorer settings feature might reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

  See also,

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/Ping.mspx?mfr=true

  Note: The link above also applies to Windows 7.

• I am trying to download a trial version of adobe captivate, I downloaded net session akamai interface, but it does not open when I click on it. I tried to download the file directly, and there is no answer. I unlocked the ads. I use an access point

  I am trying to download a trial version of adobe captivate, I downloaded net session akamai interface, but it does not open when I click on it. I tried to download the file directly, and there is no answer. I unlocked the ads. I use a mac apple OS10.6.8 and the browser chrome. can anyone help please?

  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If he continues to not try to use a different browser.

• Windows xp will not recognize or list the wireless connection.

  Original title: we changed wireless routers and now windows xp will be same not recognize or the same list if wireless connection 3 computers in the House will be

  Under networkconnections the old wireless router, or the other is visible.   I tried toads new link also with no success

  Hello

  1. What is the brand and model of the computer?

  2. who is the provider of Internet (ISP) Service?

   

  Follow these methods.

  Method 1: How to fix wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702

   

  Method 2: To create a wireless network, you can follow these steps.

  a. click Start, click run, type ncpa.cpland click OK.

  b. in the window network connections, right click on the wireless network connection icon and then click Properties.

  c. in the wireless network connection properties, click the wireless networks tab. If you do not see a wireless networks tab, your network card can not take over the automatic Wireless Configuration service.

  d. under preferred networks, click the Add button.

  e. in the network name (SSID) box, type the name of the access point, and select the parameters according to your network requirements. This setting will match the configuration of your router or access point. If you have a router or wireless access point, and then select Wireless Ad - hoc mode and use the same network name that matches other computers.

  f. click OK

  g. under available networks, click View wireless networks.

  h. in the wireless network connection dialog box, choose a network by clicking on its name and then click on connect.

  Reference: set up a wireless network

   

   

  For more information, see this article:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?T1=Tab03

• The WRT600N can connect to a wireless access point?

  I installed Windows 7 on my desktop and I was not able to install all types of Linksys wireless adapters.  I decided that linking an my WRT600N wireless access point in the other room and hardwireing the office to the access point, would be a good idea.  I'm probably going to connect it to a Net WTG624 Gear, which is capable of acting as an access point and you connect to another router.  The question is, can the WRT600N you connect to and use the internet and the local access and, ultimately, on the Office of cable?  I feel that it is one of the most stupid questions, I ask myself here again, but I'm not sure.

  EDIT: I'm sure it's called Wireless Bridge.

  Thank you

  Zach

  Hello Zach,

  The WRT600N can connect at the point of access, and vice-versa. I have a WRT600N home and have the same model of NetGear as access point (what are the chances?) and it works fine, although I do miss the 5 GHz as the Access Point is only 2.4 Ghz 802.11 g Standard.

  I hope this helps!

• C7180 not found on the wireless network

  We have a Photosmart C7180 was working wonderfully for a few years.  Wireless connectivity is great, even move to a new city/home/internet provider required only run the printer Wireless Setup Wizard, and "poof" things began to print.  So far.

  We got new internet service (new router) and now the printer is not found.  No amount of tweaking seems to be able to get our Mac to see.  We have:

  • Redownloaded and restart the installation of the driver on the Mac.  Connect via USB, it works very well.
  • Rerun Setup wireless network on the printer.  He sees the wireless network and complete Setup.
  • Checked the IP addresses: everything is comfortably accessible 192.168.0.xxx.  The printer, the computer, the router, everything in this range.
  • Connected to the printer in the Mac browser to http://192.168.0.6.  He can be seen and worked with.

  However, when we try to print or run the Mac installer, the printer is not found.

  Help?

  Success! With the help of an old wifi access point on the router and it all works. Same Bluetooth? Thank you!

• That is the accounting Radius WLC in distributed deployment of ISE server, this is the PSN or MnT node

  Hello

  on the WLC configuration for Management Server accounts Radius in distributed deployment of ISE, what server is the radius, the Service account management policy one or several nodes or the nodes in control?

  As always, appreciate your reply.

  Mike

  Hi Mike,.

  The WLC must be configured to send authentication and accounting for the PSN. Monitoring nodes are (among other functions) where newspapers PSN are transmitted to the.

  see you soon,

  SEB.

• Cisco WLC 2504 - Access Points do not reach the controller

  Hello world

  We bougth a Cisco WLC 2504 with two AIR-AP2702I-UXK9 Access Points. The problem is that the AP do not join the WLC.
  The output from 'show join ap stats' shows the following:

  (Cisco Controller) > view join ap stats summary all the

  Database Mac EthernetMac AP AP name IP address Status
  00:35: 1a: B1:A9:60 00:f2:8 b: f4:1 has: 9 c AP00f2.8bf4.1a9c 192.168.10.23 joined not
  00:35: 1a: C9:99:B0 00:f2:8 b: 77:b7:fc AP00f2.8b77.b7fc not joined 192.168.10.24

  (Cisco Controller) > show join ap 00:35:1 detailed stats to: b1:a9:60

  Synchronization phase statistics
  -For the synchronization request has received... Does not apply
  -For the synchronization completed... Does not apply

  Discovery phase statistics
  -Applications received discovered... 114
  -Answers success of discovery... 114
  -Discovery failure processing... 0
  -Purpose of the last unsuccessful attempt of discovery... Does not apply
  -Attempt to finally successful discovery time... 20:15:40.106 16 June
  -Discovery attempt ultimately unsuccessful time... Does not apply

  Join the live statistics
  -Join applications received... 57
  -Join sent successful responses... 57
  -Processing of the join request without success... 0
  -Purpose of the last unsuccessful attempt to join... Does not apply
  -Attempt to join finally managed time... 20:15:50.414 16 June
  -Join finally failed time... Does not apply

  Configuration phase statistics

  -Configuration requests... 114
  -Answers configuration successful... 0
  -Processing configuration failed... 57
  -Purpose of the last unsuccessful attempt to Setup... Invalid license in the application configuration
  -Attempt to finally successful configuration time... Does not apply
  -Time finally failed configuration attempt... 20:15:50.810 16 June

  Last the decryption of the AP details failure messages
  -Last message decryption failure reason... Does not apply

  Details of recent disconnection AP
  -Last AP connection failure reason... Does not apply
  -Last reason for disconnection AP... Unknown failure reason

  Latest summary join error
  -Type of error that occurred in the last... Application of configuration rejected LWAPP
  -Reason for the error that took place the last... Invalid license in the application configuration
  -Time which occurred the last error to join... 20:15:50.810 16 June

  Details of sign-out AP
  -Last AP connection failure reason... Does not apply
  Ethernet Mac: c 00:f2:8 b: f4:1 has: 9 Ip address: 192.168.10.23

  Would be grateful for the help.

  Best regards
  Marc

  Hi Marc,

  Make sure first that your controller has software code 8.0.x or above, if first better it. Here's the code recommended by TAC

  http://www.Cisco.com/c/en/us/support/docs/wireless/wireless-LAN-Controller-software/200046-TAC-recommended-AireOS.html

  Then, try the UX above deployment guide to begin. Under Advanced tab WLAN, you need to enable "of the first universal ap' in order to use this app provisioning & connect to the AP.

  If you have more than 1 AP, then you must start 1AP using this application. Other access points that you can feed them upward, while AP original is also powered, so they'll use protocal called NDP & start them automatically

  Let us know how it goes

  HTH

  Rasika

  Pls note all useful responses *.

• Deployment of ISE in network routing and Vlan

  Hello world

  New bee to ISE. I want to help/suggestions on how to deploy ise in my network or comment if my plan is working

  Machines to ISE, Servers (ALL) and Corporate (Dot1x and field) in vlan 10

  Comments should be in the vlan separate 20

  By default that all switch ports must be in the vlan 30 having nothing but only to DHCP.

  Each endpoint must come through vlan30 and then pushed to vlan respective IE 10 if corp (Dot1x) PC and comments vlan 20 if mab and do not appear in the endpoints.

  What is a successful deployment?

  Secondly the fact inter - vlan routing is required in this scenario for the endpoints to be controlled properly.

  ISE are able to communicate and of endpoints that are not in the VLAN of the police.

  Hello

  Deployment of the ISE requires a lot of consideration in many aspects. Suggest you read the cisco documentation carefully to become familiar.

  http://www.Cisco.com/c/dam/en/us/TD/docs/solutions/enterprise/security/T...

  Node ISE Cisco plays many roles; Admin, monitor & Service policy. The crux of the political service (PSN) is one who plays the role of RADIUS (RADIUS of tip to be precise) server to handle requests from the AAA.

  For authentication dot1x internal hosts, you can have a PSN ISE in-house LAN (VLAN even as servers) or users. Whereas, for wireless clients, you can use a dedicated NHP or share the PSN according to safety requirements.

  See you soon,.

  Vidy

  Please don't forget to rate this post so useful.

• ISE 1.2 rejects 5508 WLC RADIUS messages

  The setup of ref is:

  WLC 5508 HA pair running 7.6 talk with ISE 1.2 patch 7 (a 6).

  Wireless users are authenticated very well, so the 5508 is a valid n in ISE, but...

  When I install active RAY of relief, so that the WLC can query the ISE Server I get the message:

  "The query a device no RADIUS wireless was interrupted because the installed license is for wireless devices only.

  Why the ISE spend a RADIUS of a WLC message which is a wireless device?  It is certainly a mistake?

  Hi Nicolas,.

  This is a known fault.

  CSCug34679    ISE drop keep alive from WLC.

  Symptom:
  ISE drops keep living authentications from the WLC, with message 11054 request from a device no wireless because of the license installed wireless.
  Conditions:
  When only licensed wireless is installed on the ISE and use current keep alive on the WLC.
  Workaround solution:
  Passive use keep alive on the WLC and non-active.

  Kind regards

  Jatin kone

  * Make the rate of useful messages *.

• Check the ISE for the VPN Cisco posture

  Hello community,

  first of all thank you for taking the time to read my post. I have a deployment in which requires the characteristic posture of controls for machines of VPN Cisco ISE. I know that logically once a machine on the LAN, Cisco ISE can detect and apply controls posture on clients with the Anyconnect agent but what about VPN machines? The VPN will end via a VPN concentrator, which then connects to an ASA5555X that is deployed as an IPS only. Are there clues to this?

  Thank you!

  The Cisco ASA Version 9.2.1 supports the change in RADIUS authorization (CoA) (RFC 5176). This allows for the gesticulations of users against the ISE Cisco VPN without the need of an IPN. Once a VPN user connects, the ASA redirects web traffic to the LSE, where the user is configured with a Network Admission Control (NAC) or Web Agent. The agent performs specific controls on the user's computer to determine its conformity against one together configured posture rules, such as the rules of operating system (OS) patches, AntiVirus, registry, Application, or Service.

  The posture validation results are then sent to the ISE. If the machine is considered the complaint, then the ISE can send a RADIUS CoA to the ASA with the new set of authorization policies. After validation of the successful posture and CoA, the user is allowed to access internal resources.

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-Appliance-ASA-software/117693-configure-ASA-00.html

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.