Design jet 350 c: design jet 350 c
We use only black ink on this plotter and the manual says not to operate without the other 3 colors of the
plotter. Is there a way to convert it to a 350 c just a 350
Thank you
Motherboards for the 350 c and 330 are the same. The only difference is the chip ROM. The part number for the ROM chip for the 330's C4699-60104. Hard to find part. If you can find a substitute your current ROM with this simm will change the model of the 330 which I believe is black only.
Tags: HP Printers
Similar Questions
-
HP Design Jet T920/T2500 Pages can be printed with the new HP 727 130 ml.
Hi guys,.
I want to ask you how many Pages can be printed in the new HP 727 130 Ml of INK CARTRIDGES. Normal, black and white printing on Hp Design Jet T920/T2500. One of my customers asking me this way, I'm looking for and read about the manual but this is not to mention the approximate number. pages can be printed. I appreciate who can help me and share their experience with this concern.
He mentions on the manual which:
Can be printed 120 Page A1 and A0 60 per hour, but HP 727 130 ml (returns/Pages)?
Thank you and advance...
I doubt that there is no information for this because inkjet printers work differently then laser where they use a percentage of coverage for compiles the approximate pages toner. With Designjet printers there are many variables outside coverage that would be very difficult calculations. You will be dealing with page sizes and even with normal printing or graphic images line densities will have much to different amounts of ink laid according to the original plot, type of paper used, etc.
-
printing for design jet 430 cable
DESIGN JET 430 (BLACK, NO COLOR PRINTING) ALLOWS YOU TO PRINT WITH A PRINTER ADAPTER USB FROM THE PARALLEL CABLE?
I SEE ON AMAZON DIFFERENT SOLUTIONS:
(1) USB 2.0 - IEEE 25 POLES DB25 PARALLEL ADAPTER
(2) USB 2.0 - PARALLEL IEEE 1284 36 LPT ADAPTER PIN DB36
What is the current connecvity to the device & what operating system. The current setup works well?
The adapter cables may or may not work, you may need to take a risk if you think it is better to buy.
-
a cartridge 26 replace a cartridge 82 a design jet 510 does
a cartridge 26 replace a cartridge 82 a design jet 510 does
Hello
Please check the packaging, the is a cof list compatible printers. In addition, depending on where you are, all I can see here is that they are not the same shape and size:
26: http://www.cartridgesale.com.au/compatible-HP-26-51626aa-black-ink-cartridge-p-841.html#.UTT011eSmo8
82: http://www.hottoner.com.au/82-Designjet-500-800-yellow-ink-62317.html
Kind regards.
-
HP Design Jet 520 blue with code screen
Turned on the printer and the blue screen with the code 805DFE31 on tried unplug power many time always comes back.
What should I do?
Hello
Try to isolate the printer, remove another outlet, cable connectivity, print head, ink, and then the printer.
If you still have problem, please replace the encrypted hand APC Kit (P/N: CQ891-67019)
PartSurfer: http://partsurfer.hp.com/Search.aspx?SearchText=CQ891-67019
It is my understanding that the new hand APC should come with the USB with the FW. Make sure it's there before to install the new main PCA.
If problems with the FW, will not recommend you to use old USB with the firmware again.
Thank you
Rashed
I'm not an employee of HP, but I am an engineer @ HP Partner and I share my knowledge of my own time.
If your problem is resolved please click the button "accept as a Solution.
If my answer was helpful, please click the 'Thumbs Up' to say 'thank you '. -
Design Jet T610: Designjet T610 noise deaf when printing
Recently, we had our belt changed and now there's a THUMP from the right side of the printer. It was printing normally with the noise for several months. WE do not often use it. It has become a noise problem. It's a thud coming clearly from the right side, but it is still printing is not the print head.
Any ideas?
I will private message you a link where to find the Service Manual - of the socket replacement procedure starts on page 6-137. the video is wrong in detail on the importance of this piece, but at least gives you an idea of what you would be facing.
-
Design jet 500: 500 Print Design
Does anyone know the screws of mounting/wire? I look lost in a recent move and really need this printer is operational.
I found them to be screws 4 x 30 mm
Thanks for all the help.
-
Design Jet 5500: replacement of printhead
Hello
I'm trying to replace the printhead on the HP DesignJet 5500 and following the instructions in the manual and the video guide on the CD (which is straight forward), but come with a question.
I have reached the stage of "Sunrise door above wagon" and a few seconds the print carriage moves back behind the front before the step of "pull and release the latch on the top of the cart. I am concerned when I release the lock to reveal the print heads to get behind the front until I had time to replace the print head and cause damage.
Why the printhead carriage moves during this process? Is there a way to stop this, so I had time to replace the print head?
Thank you
On the right side of the top cover is a protuberance that based on a small switch in a hole at the top to indicate to the printer top cover is closed. When you follow the instructions to replace the print head, the carriage moves to the left and wait about 30 seconds for the roof to open, knowing that he opened when happening releases. On your machine, the switch for a reason not publishes so the printer think that you do not change the print head and transportation goes back. See if something is crowded in that little hole. If you bought the printer from someone, sometimes, when he is assured that breaks switch for technicians find a way to activate it otherwise the plotter will not work. Last use what you need to do and stops is when the carriage moves to the left is turn the printer off with the switch at the rear of the machine. Then change the print head, close the lid on the transport and the top cover, turn on the power and when the printer has completed initialization is calibrates the printheads. To test if I'm right, just open the Center cover with the printer by hand or replace the print head message. It should tell you to close the cover and is it does not means that the switch is always on.
-
I am a technician working on a HP design jet t920, desplays error restart 21:13
HP designjet T920 broadsheet desplays error 21:13 before initialize completely and restart if persist contact for service. I tried to clean and lubricate the machine but no change. Kindly help
Newsyl3
Hello
The error is related to the Station (SS)
Look for any obstructions
Clean the MICR band to make sure that the ramasseherbe is not on the wrong place when the SS moves
If you have noises coming from the SS, when he tries to move or does not move, you may need to replace the part
-
Printer more HP Design jet 500
It comes with error n ° 21:10
Gas station replaced is always delivered with 21:10 error. checked the gas station and it works.
What could be the problem.
Thank you
Mahrez
Have you maybe just changed the belt. If you did most likely pinch you the big gray water that goes from the emod when you put the right holder back on. If so just remove the mount again and make sure that the cable is loose after putting the leg back on. Also, make sure that the coding is clean on the right side of the gas station. Clean gently with a damp cloth.
-
A new printer installation just came out with a message.
Not enough ink to complete the installation. Door open ink to replace the cartridges indicated or press OK to insert other PHA.
How can I approach this problem? any help?
Thank you
Mahrez
You could try to remove the cartridges and shake them a little and then put them back in to see if it ends. But if not, it looks like you will have to do exactly what her tell you. Replace the cartridges listed. The cartridges supplied with it should have at least enough ink in them to complete the installation process. As its new brand, it is under warranty and you might be able to get HP to send you replacement cartridges.
-
Re: Satellite 350 - power plug loosens
Hi, I've had my 350 Satellite for over a year now and it has been already to toshiba for repair twice for the same reason the power plug loosens and once fall completely inside the machine.
These repairs were covered by the warranty but now that my laptop is more than a year, it has run out of warranty, but this problem with the jack happened once again if you think toshiba will except responsibility as it should be a lack of design etc.?
Hello
I think you should contact them (SAV) and ask them what to do.
Welcome them
-
HP Office Jet J6480 All In One - will not analyze with Mac OS 10,8.3
I could not get my HP Office Jet J6480 All In One scanner after upgrading to 10.8.3.I followed other positions and have installed the most up to date driver (http://support.apple.com/kb/DL907) , but whenever I try to scan from the HP Device Manager or photosmart studio, it says "sorry, scanner could not be initialized. (scanner not found) "I tried to make sure there is no other updates by clicking settings in the Device Manager by clicking on check the updates but it says 'server not available - service software is currently not available. "Please try again later" and I got this error for the last week.
I followed the second set of instructions available here: http://h30434.www3.hp.com/t5/Mac-Printing-and-Scanning/HP-Software-Update-Server-Unavailable/td-p/18... to try to resolve this problem and install the software found on the link. I restarted my computer and I always meet the same problem.
Note: My printer is wireless and I have not hooked by a cable. Will make a difference?
My printer seems to be printing very well.
Thanks for any help you can provide.
Sara
To add, both HP Device Manager or photosmart studio are part of the software and not designed for Mac OS X 10.8 10.5.
Here are the steps to scan with your printer on mountian lion, make sure to run the software update first to ensure that the latest HP drivers are installed:
http://support.HP.com/us-en/document/c03550518
Where the scanning software do not work as expected, that more probably caused by incompatible drivers installed on your system.
In this case, remember to remove the software by following the HP uninstaller program (under Applications > Hewlett-Packard), rebot Mac and install the correct software by following the steps below:
http://support.HP.com/us-en/document/c03378792
Shlomi
-
Devices that are compatible with the Tablet HP Jet 7 Signature Edition
With HP Jet 7, what Bluetooth wireless keyboard and optical mouse will work with it?
Also, I buy a wireless printer to use as well - I have to be aware of?
I'm starting a blog with limited capital. Thank you to everyone who contributes to the cybercomputability of us all.
Hello and welcome to the HP support community!
Ask us the question, "what should I buy?" is difficult to answer. We do not know your needs or preferences (others you have "limited Fund"). There are hundreds of printers with wireless capabilities. Still, we don't know what you're wanting - ink jet, laser, color, photo printing capacity jet, absolute who is cheapest available? Print you hundreds of documents per month, or two or three?
You ask strictly for HP products which are compatible with the Tablet? All/all products from other manufacturers?
If you are expected to produce a list of all the possible volumes that work, it won't happen...
In theory, any BlueTooth keyboard or mouse designed to work with a Windows PC should work. HP made several.
Most wireless printers use a wifi network. It will help if you have one at home - an HP ePrint printer can print a file from anywhere in the world if connect you to a network home. No network? There are other printers that can print directly using wifi.
Think about your needs first, and then balance the costs involved. It would be useful you ask on the printers in the printer of the Forum sections.
WyreNut
-
HP Office Jet 8600 Fax (not fax)
Recently, I asked my web company to change my modem in order to include a telephone line so that I can use my fax on the HP Office Jet function and I have such a misery the fax to work. When I plug the cable from the printer (line 1/2) to the modem (phone line) and I run the fax test, it tells me that there is no dial tone. Can anyone help!
It is because this isn't the preferred method for the transmission of faxes. You will probably need a digital filter on the line to improve your chances of send/receive. However, even with this it is not a guarantee for fax technology is designed for a telephone line analog, not who is associated with an internet service.
This is a documentation on the best ways to set up the fax machine: http://support.hp.com/us-en/document/buu50333
I would certainly try the digital filter on the first line. And if that does not work, or the quality, I would say either using an analog fax line or a digital fax service (both cost about the same amount).
I hope this information is useful and have a great day!
Maybe you are looking for
-
Loop without end of connection/re-auth in Wordpress - with Firefox only
Hi all I have a problem in some installations of WP for a long time. In Firefox only, I am stuck in a loop of waiting/session connection timeout. I go to the admin... It shows me the login screen, I have the connection with a known and username worki
-
Remote Desktop has stopped working suddenly Premium Ultimate
I used to be able to remote desktop to my laptop with Vista Home Premium on my desktop with Vista Ultimate. All of a sudden, it stopped working (March 09). I tried many steps of troubleshooting without success and I searched and searched online with
-
Upgrade are failed! WRT54G_v2
130228_1900est Hello troed just re our WRT54G_v2 FIRMWARE update Current FIRMWAREFirmware version: v3.37.7 downloaded and tried to run 130228dl_LINKSYS_FW_WRT54Gv4_4.21.5.000_20120220.bin BUT I got the msg' Upgrade are failed! What's wrong? Thank you
-
How to load a .exe in GameMaker 8.1 standard?
GameMaker will never be and edit me an .exe file. Is there a way to fix this?
-
Version number in the label (request for information)
Hey guys, I can't figure out how to make it work. Here is my code: application. UI #include ... ... ... ApplicationUI::ApplicationUI(bb::cascades::Application *app) : QObject(app) { ... ... //version info bb::ApplicationInfo appInfo; setProperty("ver