Designjet 111 & Jetdirect 635n

Similar Questions

• Designjet 111: HP Designjet 111. Cross any line put in place every time his tour on

  Hello

  I have a HP Designjet 111 with a feed roller.

  The other day one of the printhead needed replacing I did. Now, whenever I turn on the printer, it goes through any line established the points of printing color page. It prints three times which takes about 5 minutes. If I turn the printer market again once he does all this again.

  I tried to replace the print head with one another but same problem. I always use the new genuine HP print heads and HP ink cartridges.

  Once set up over it print without any problems.

  Any ideas?

  Thank you

  This is because it does not have alignment.  It tries 3 times.  Look at the line with the X in the right margin.  It is the color, the origin of the problem.  Just look at the small boxes and you should be able to tell what printhead (s) must always be replaced. If the print quality is very good, then simply press the Cancel button as the first leaf begins to print and it will cancel the calibration.

• Designjet 111 roll: problem with Hp designjet 111 roll

  Hello

  I have problem with Designjet 111 roll. I reinstalled the driver delivered with CD, and the most recent Web site and the effect is always the same. When I enter the Properties window, I see this:

  

  There is no chance to put anything. How can I solve this?

  Hello

  The System Maintenance Utility will not be related to a problem with the printer driver.

  Have you deleted the driver as explained on the following doc?

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-bpp03332

• Designjet 111: Need for Designjet 111 installation CD

  Hello

  Anyone who has a CD to install Designjet 111?

  I just bought a Designjet 111 opportunity.    I realize the printer is obsolete, of course. But it was sent to me without an installation CD.

  I tried to contact HP support, but I have not found all the solutions.

  If anyone has an installation CD, I would be very grateful if you can let me know if you were happy to part with it and for how much.

  Thank you very much.

  Hello

  You can find the SW installation on the following link

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=11203511 & swItemId = pl_84217_5 & swEnvOid = 4063

• Designjet 111 (nominal): Designjet 111 / Windows 10 / instead of pointing it prints to the prn file

  Hello

  I use Windows 10 and Designjet 111 (roll). I already downloaded the driver and everything seemed OK, but after printing the confirmation of the window, rather than send the drawing to the plotter, the next window opens to save the drawing as a .prn file. The button "save to file" in the window "Advanced" is clear.

  He had no problem with printing on Windows 7.

  See you soon

  OK, I solved the problem.

  In the printer properties / ports window 'Print to file' port has been marked. I just changed to the USB port.

• Designjet 111 - printing problem

  My Designjet 111 printed 6843 pages. Almost all were 24 "x 36" CAD. Changes of cartridge & usual ink print head.

  Two days ago the plotter has stopped printing. It was a pdf CAD and got about 1/2 ", then stopped.

  Maintenance of the 532 system error codes:

  # 0, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 1 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 2 S.06.04 SM 86.11: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 3 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 4 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 5 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 6, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 7 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 8 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 9 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844

  Code of error starting Track = 167 = init PrintHeadControl

  I put in four new print heads with the same result

  Changed the ink also.

  Not sure whatelse to do to get the tracer is going?

  Any help would be greatly appreciated

  Roger

  SOLVED

  You have a printer independent guy tech $80, which has stripped the DJ11 and cleaned, inspected all parts.

  Nothing broken just a lot of cleaning.

  Head of transport that reads the MICR band was dirty.

  HP support (Vijay in India) was useless

  Hope this helps some other users DJ11

  Roger

• Designjet 111 does not start prinring or stops in the Middle

  Hello

  I recently bought a designjet 111. The first page I printed (linedrawings) came out perfectly, the second page, I tried (linedrawings + a few pictures) the printer no longer starts.

  Now, I have the same problem: the printer just will not start. I tried to turn my laptop and printer, changed USB ports, off the sign 'offline',... nothing seems to work.

  Then all of a sudden it started printing (not sure what I did differently), but stopped after 5 centimeters, drove from the page and cut it. I tried again and then print 30 centimetres and stopped. Now, it does not print at all.

  What can I do?

  OK, problem solved by changing the usb cable to the laptop.

• DesignJet 111: DesignJet 111 - printing problems - no printing after upgrading to Windows 10

  Several problems to the upgrade of WINDOWS 7 for WIN 10.

  The HP DesignJet is 'offline' and can't figure out how to change the setting of "online."

  The definition "print directly to the printer" is not.

  Yellow flashing on the printer dashboard - magenta ink cartridge shows empty, but it is full.

  Computer HP printer installed - poster is in the Device Manager - watch "this device is functioning."

  Printer is listed in devices and printers.

  HP Support Assistant doesn't recognize - printer in the list, can not find device during an attempt of "add design.

  Printer turns off or recycle off on after turning on.

  Hello

  If you have a driver problem:

  Remove the driver completely from the computer, then download and install the lates driver.

  Here is the link incase you need

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4123145 & swLangOid = 8 & swEnvOid = 4192

  Now, the yellow light flashes on the Panel means that the printer needs attention, like:

  -Close coverage which is open

  -Of paper

  -Paper tilt

  -Jam

  -An error code

  If you have 6 columns on the levels of ink instead of 4 is because you have an error code.

  On the following link, you can find more information on how to prepare the error codes

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=352387 & docid = emr_na-bpp03841

  If you have an error code, the printer appears offline on your computer.

  On this other link, you will find how to check other messages on the printer

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01669949

• Printhead Designjet 111

  Hi people!

  IM new to this forum and have a bit of a problem.

  I just changed the yellow in my machine print head because he started bands. Once in a new, is not printing at all. There is nothing on the front panel flashes to show that I have a problem. So, just for fun, I put the old back in and still the same, no ink. Sorry for sounding silly, but is - it possible that a 'pump', or something of this ink from the print head pumps gone bad?

  I hate the idea of that something big went wrong shot, because I use this printer for about 5 years with absolutely no problem.

  Thanks in advance for any help.

  chuckj

  This forum focuses on the level of consumer products.  For the Designjet that you can have better results, post in the forum HP Designjet here, this is where the Designjet experts.

• HP Designjet 111 with 24 "Roll: Arch D is no longer available in the print options

  Normally print us PDF drawing (using Adobe Reader) set to Arch C (18 "x 24"), but sometimes we need D Arch (24 "x 36").

  Ark D has somehow been removed from our drop-down list of options. When I try to use customize the size of 24 "x 36", I get a pop up window that indicates that the size is too small or too large. I don't see any other way to add Arch D in the list of options.

  I tried the update of drivers, but the message says I have the latest. We have been updating for Windows 10 a few months ago and I don't know that it had no effect on these options.

  Thanks in advance for any help.

  Solution, it turns out that the printer now ready for print Arch C value by default, and in the settings is a checkbox to rotate 90 degrees.  When this element is on the Ark D option disappears from the list of options.  Note: Also noted that under the 'effects' tab / resizing Options, we set to Arch C, I think that's the main problem of the loss of the ability to print Arch D; Choose 'full size', now able to print once more drawings D arc.

• HP Designjet 111 24 "color sublimation support

  Hello

  I searched through the documentation, most of the data that can find are: ink-Types(Dye-Based and Ink-Based)

  I need a printer for printing in color sublimation. Is - this model have it?

  Thank you!

  You might have better luck here.

  http://h30499.www3.HP.com/T5/business-support-forums/CT-p/business-support

  You are now on the consumer assistance page and the printer you want is probably a bussines unit.

• DesignJet 1000 Plus Series: JetDirect 680n (wireless) & DesignJet 1000 Plus - what is the required minimum firmware revision?

  For JetDirect 680n (wireless) & more / 1055CM DesignJet 1050c more - what is the minimum required for a 1050c or 1055 CM firmware revision more? I guess that at least a minimum of a certain firmware revision is necessary. Thinking about doing a JD 680n wireless connection.

  I suppose that it would work with A.52.02 (PS or RTL) firmware revision but she would work with A.52.01 ch (1055 CM Plus) I have?  and A.02.10 RTL (1050c more) I have?

  Thank you.

  Version of the firmware should not matter.  See the link below for a list of compatible printers.

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-bpj07274

• HP DesignJet 650 c on Windows 7 x 64 via LAN with JetDirect adapter

  Hello good people!

  I would like to know if a DesignJet 650 c (C2858B) with a JetDirect card can be installed via the LAN on a PC running Windows 7 (64 bit)? If Yes, could someone please advise on how to do it?

  Any help would be greatly appreciated.

  Thanks ~ Tim

  Yes, it's exactly the setup I have (with a JetDirect card installed in the 650 c).  Follow these steps:

  The 650 c and connect it to your router with a LAN cable.  Then, press Enter façade, then arrow down three times to get to, Enter, modular i/o of installation configuration, come in, Cfg network = NO, Enter, arrow for Yes.  At this point theCfg network = NO * reappears, it is normal.  Press previous return to main menu of status.  Then press ENTER, down arrow until you get to the utility, enter, down arrow for plot, Enter Config.  Once the plot ends at halfway in the page search for MIO, the IP address for the plotter configuration information will be available on the right side of the page.

  At this point your plotter is set up and ready, then get the driver installed on your PC.   These drivers work fine for Windows 7 x 74 (and also Windows 8 x 64) you can install the XP x 64 drivers as described in this post.

• Portal HP DesignJet 1055 CM more

  Hi all

  I recently got a used HP DesignJet 1055 CM Plus and when turned on I got the error mentioned here:

  Designjet 1055 cm Plus - error code 007 has a 0251 09 001

  So I removed the internal HD, following the instructions here:

  DesignJet 1055 CM plus - replacement hard drive help

  After removing the disc hard/Daughter Board (1055 CM Plus is equipped with an internal HD as mentioned in the thread above), I have cleared the error and the printer started normally. However, I have a few questions:

  1. The printer can operate normally under the descriptions very on the internal hard drive?
  2. The hard drive can be replaced with the HD external accessory port like the 1055 CM?
  3. I read the answer in the 1st thread above by user DavidZuts that there is a driver (GL2) that you can use less hard on this model. Can someone develop on that? I'd like to get this thing print again, but I need to know if everything works. Other suggestions are welcome and would be useful!

  I apologize if I walk on this forum with too many questions, but I'm glad that this forum is full of so many knowledgeable people. I have another would have been up a Creek less a paddle.  If it's useful I intend using this tracer in a mac environment via the jetDirect network port.

  Thank you!

  The printer will work without the hard drive, but you will not be able to use a postscript driver. If you need such as the use of a MAC postscript, then Yes you can use a hard drive of the 1055 CM. I know it works because I had to change the room either a customer with a longer Board and I moved the hard drive. I had to use a longer back cover because the slots did not, line up but will not be your problem.

• Unable to drawings SolidWorks great impression for HP DesignJet 500 via Server

  Hello

  Our company has a HP DesignJet 500 with 24 "Inker for tracing large pages of design drawings created in SolidWorks to our technical workstations.  These workstations all have Windows 7 64-bit with 8 GB to 16 GB of RAM and 1 TB of hard drives and intrigue to the drawing via on board our servers (Server 2008 32 bit with 4 GB of RAM), which connects to turn over a connection IP to JetDirect EX Plus (with a sleeve of 10 Mbit / s and a CAT 5 network cable) and a parallel cable.  Lately we had problems tracing of parts of very large assembly drawings (100 MB + size), by which desktop lock when trying to trace.  They can even preview before printing (print dialog box disappears when the user clicks the Preview button).  Restart the plotter and the JetDirect gave no results better.  The server has plotter driver installed v6.08 (data file version 2.1), and the tracer itself is on firmware 3.03 version.  No errors are appearing on the plotter except an error of 79:04 in December.  Tracing a bitmap file doesn't seem to be a problem, but I could not try the other formats again.

  Any thoughts?

  Thanks in advance,

  Michael

  In the properties of the driver, there is a tab services which must display a troubleshooting icon and you can click on "Run as bitmap".  This will allow the desktop process files to print instead of the printer, which cannot process large files.  It is the only way to execute works of old printers not designed to process.