Designjet 111 - printing problem

Similar Questions

• DesignJet 111: DesignJet 111 - printing problems - no printing after upgrading to Windows 10

  Several problems to the upgrade of WINDOWS 7 for WIN 10.

  The HP DesignJet is 'offline' and can't figure out how to change the setting of "online."

  The definition "print directly to the printer" is not.

  Yellow flashing on the printer dashboard - magenta ink cartridge shows empty, but it is full.

  Computer HP printer installed - poster is in the Device Manager - watch "this device is functioning."

  Printer is listed in devices and printers.

  HP Support Assistant doesn't recognize - printer in the list, can not find device during an attempt of "add design.

  Printer turns off or recycle off on after turning on.

  Hello

  If you have a driver problem:

  Remove the driver completely from the computer, then download and install the lates driver.

  Here is the link incase you need

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4123145 & swLangOid = 8 & swEnvOid = 4192

  Now, the yellow light flashes on the Panel means that the printer needs attention, like:

  -Close coverage which is open

  -Of paper

  -Paper tilt

  -Jam

  -An error code

  If you have 6 columns on the levels of ink instead of 4 is because you have an error code.

  On the following link, you can find more information on how to prepare the error codes

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=352387 & docid = emr_na-bpp03841

  If you have an error code, the printer appears offline on your computer.

  On this other link, you will find how to check other messages on the printer

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01669949

• Designjet 111 roll: problem with Hp designjet 111 roll

  Hello

  I have problem with Designjet 111 roll. I reinstalled the driver delivered with CD, and the most recent Web site and the effect is always the same. When I enter the Properties window, I see this:

  

  There is no chance to put anything. How can I solve this?

  Hello

  The System Maintenance Utility will not be related to a problem with the printer driver.

  Have you deleted the driver as explained on the following doc?

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-bpp03332

• impression of Pro to Z5400 Designjet HP printing problem

  Last October, I bought a Postscript Designjet Z5400 printer. On both CD and software down loaded from the Web site called "HP printing Pro" produces an error on the screen of the printer "Incorrect, impossible to print file Format". This happens with. JPG. PDF and. TIF (any graphic file) files.

  The printer precisely will not respond to the controls of Photoshop CC either. Try to compose a set of 5 "x 7" photos in the upper part of a 36"wide roll of results of paper in the images printed on one side of the paper with massive losses." The problem seems to be that the printer will not allow a page size to create what is shorter than the width of the paper.

  I have been in touch with HP about this and offered a refund, even if I sent my own to the printer, not me Bank evidence. Answers like "It's a HP offer for you, not the finance co" suggests HP trying to me to commit larceny as a custodian... A criminal offence.

  I did not buy this printer for a refund, I bought it for a living with. Twice now, I tried to access the part "next day guarantee support" of the Pack in customer care, I paid an extra $1200 for and not received a response.

  I am able to print to this printer, but not using the software from either HP or Photoshop CC. Any help here as to who speak for the "next day" service, I bought or the highest level of management, I can access complaint with all the terrible service, I was making would be apreciated. I have a video broadcast quality of the mess that occurs when you try to use this printer, but I hesitated to post publicly until a person at HP has actually been and looked at the problem. It's either the printer or the HP software cause.

  Thank you

  Ryadia.

  Hello ryadia,

  I just sent you a private message.  If you are unsure how to check your messages from the forum, this post has instructions.

• Designjet 111 (nominal): Designjet 111 / Windows 10 / instead of pointing it prints to the prn file

  Hello

  I use Windows 10 and Designjet 111 (roll). I already downloaded the driver and everything seemed OK, but after printing the confirmation of the window, rather than send the drawing to the plotter, the next window opens to save the drawing as a .prn file. The button "save to file" in the window "Advanced" is clear.

  He had no problem with printing on Windows 7.

  See you soon

  OK, I solved the problem.

  In the printer properties / ports window 'Print to file' port has been marked. I just changed to the USB port.

• My problem is the wrong color on a HP Designjet 90R printer (Q6656B # model)

  Impressions I made yesterday are way out of colorwise.  They appear especially orange where there should be no orange.  The parts must be orange are very orange.  Blues look a little purplish.  Greens don't show at all.

  I thought it might be a profile in initially and possibly problem, a problem of Photoshop CS5, because I have read there are some printing problems with CS5, (it was the first time I printed with CS5), but I printed using CS5, CS4, and CS3.  CS5 and CS4 were on a Vista machine the CS3 on my laptop with XP.  I tried printing with different profile settings including one that Photoshop has been lacking for years.  All the results were bad.

  One thing I discovered while poking around the printer was the printhead cover right hinge is broken.  I don't know the part that you pull to the front of the printer, lift, and then again to release.  It wobbles when released and when locked it appears on the left side of the cover is a little lower than the right side.  This may cause a problem printing?

  I don't know what else to say that I am no expert in this.

  I would appreciate any assistance.

  Thank you.

  This forum focuses on the level of consumer products.  For the Designjet you can have better results, post it in the forum HP Designjet business here.

• Designjet 111: HP Designjet 111. Cross any line put in place every time his tour on

  Hello

  I have a HP Designjet 111 with a feed roller.

  The other day one of the printhead needed replacing I did. Now, whenever I turn on the printer, it goes through any line established the points of printing color page. It prints three times which takes about 5 minutes. If I turn the printer market again once he does all this again.

  I tried to replace the print head with one another but same problem. I always use the new genuine HP print heads and HP ink cartridges.

  Once set up over it print without any problems.

  Any ideas?

  Thank you

  This is because it does not have alignment.  It tries 3 times.  Look at the line with the X in the right margin.  It is the color, the origin of the problem.  Just look at the small boxes and you should be able to tell what printhead (s) must always be replaced. If the print quality is very good, then simply press the Cancel button as the first leaf begins to print and it will cancel the calibration.

• Designjet 111 does not start prinring or stops in the Middle

  Hello

  I recently bought a designjet 111. The first page I printed (linedrawings) came out perfectly, the second page, I tried (linedrawings + a few pictures) the printer no longer starts.

  Now, I have the same problem: the printer just will not start. I tried to turn my laptop and printer, changed USB ports, off the sign 'offline',... nothing seems to work.

  Then all of a sudden it started printing (not sure what I did differently), but stopped after 5 centimeters, drove from the page and cut it. I tried again and then print 30 centimetres and stopped. Now, it does not print at all.

  What can I do?

  OK, problem solved by changing the usb cable to the laptop.

• Designjet 111: Need for Designjet 111 installation CD

  Hello

  Anyone who has a CD to install Designjet 111?

  I just bought a Designjet 111 opportunity.    I realize the printer is obsolete, of course. But it was sent to me without an installation CD.

  I tried to contact HP support, but I have not found all the solutions.

  If anyone has an installation CD, I would be very grateful if you can let me know if you were happy to part with it and for how much.

  Thank you very much.

  Hello

  You can find the SW installation on the following link

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=11203511 & swItemId = pl_84217_5 & swEnvOid = 4063

• Designjet 500 prints on usb but not ethernet

  I inherited a DesignJet 500 printer 24 in. I can print so that I am related to him by a USB cable but when I try to set up on my network, I can't print to it across the network.  I can ping the JetDirect card and can telnet in as well so I know that I have the correct IP address and it the card itself can communicate with my network.  I use the same driver via the USB port and the network port but still unable to print over the network.  Any ideas why I can connect to the printer on my network, but I can't print on it unless I connected locally with a USB cable?  I tried with a laptop running XP32bit and Win7 64 bit with the same results.

  Thanks for the help.

  Thanks to the entrance to the Forum of commercial products.  BTW, I discover to my problem.  It looks like the problem was the cable used to connect to my network.  One of the things that I should have checked first, but don't have.  After replacing the cable, I was able to print from the network to it.

• Where can I find better, more correct instructions to solve printing problems by editing prefs.js?

  Instructions of "resolve printing problems | Firefox Help, line 6. Delete all the lines in prefs.js that begin with print_ and save the file. "do not match what is actually in my prefs.js file.

  In other words, he didn't y not the lines * beginning * with "print" or "print_". However, the string of five characters 'print' is * very * many times buried deep in a line of characters, but never at the beginning of a line and rarely followed by underscore. So I have no idea what I'm actually planned to do to solve my problem.

  It seems to me that this is just a badly phrased statement that might be more appropriate for someone who is familiar with the codification and development of software, which I'm not. I don't have the time, experience or knowledge to understand. I need more literal/explicit/specific instructions.

  The printing problem I have is that I have to print via WiFi to a printer in another room wired to another computer, and Firefox seems to switch or possibly reverse scales fonts for information of margin and the text of the Web page. In other words, the title of the document, date, time, prints etc very wide and the content of the page text prints almost too small to read.

  If there is a lot of user set prefs involved that need to be reset, then it's much easier to delete related lines of the prefs.js is each of them with the button straight on the topic: config page and click Reset.
  This is the main reason (single) to edit the prefs.js file.

• Print problems with the recent update to Version 10.11.5

  Print problems with the recent update to the Version of El Capitan 10.11.5.  Cannot print to my Epson and Samsung printers after update to new IOS.  Print jobs get hooked on my Mac Pro.

  Roger 510 wrote:

  Print problems with the recent update to the Version of El Capitan 10.11.5.  Cannot print to my Epson and Samsung printers after update to new IOS.  Print jobs get hooked on my Mac Pro.

  Have you checked with Epson for an updated printer driver?

• From updateing to 8.1 WIndows printer problems

  Until I updated to Windows 8.1 other months everything was going well on my new laptop, then I went to something of my HP Photosmart B109n scan and it did not work because the pilot was now missing and the application that replace the HP printer driver HP is useless.

  On the advice of the HP site, I tried to download the new driver, but it wouldn't go, he said I had to remove the exsisting installation but when I try it just reboots the computer, but is still there afterwards. It turns out the uninstall has disappeared from the current and installation does not appear in the installer I downloaded.

  As a last resort, I used the system restore but has not only the printer has not changed but now some pre-loaded apps will not work and ask to renew the license of developers.

  I'm a lost what to do next - please help!

  Your laptop is not known to me, but in the case of update 8.1 Win, you should check this update from Toshiba to win 8.1 page: http://www.toshiba.eu/innovation/gen...ws8_1-message/

  There you can check if the Win 8.1 is supported on your laptop and how to perform the Update step by step for Windows 8.1
  Some drivers must be uninstalled and updated after installation of update 8.1 to win!

  Regarding your printer problem:
  Each manufacturer of the printer contains own drivers for the Windows System.
  We don't know me if HP released Win 8.1 compatible drivers for the printer Photosmart B109n clean, but to be honest, this problem is not related to the Toshiba laptop. If you have problems using HP printer under 8.1 to win, you should visit the support page of the printer manufacturer for troubleshooting tips and workaround solutions.

• Eny HP 4520: Printing problems in word Document with photo

  I just purcahsed a HP Envy and I use the function print via the wireless option. I have a word document that I was able to print in the past which has an image inserted into the document. All in the words fine printing copies only the upper left photo f. When I show preview before printing, it shows that if the whole of the document will print correctly and the image should print very well... I have attached what print preview looks like and what actually prints

  Hi @dmanyeah,

  Thank you for reaching out to the forums! I understand that you encounter printing problems in Word, the full image is not printing. Thanks for providing the screenshots. I'd love to help you.

  Try to print a picture from another application to see if you have the same problem.

  To exclude the driver, install a generic driver to see if you have the same results.

  • On the computer, go to start, devices and printers, right-click on your printer and select printer properties.
  • Click the Advanced tab and click new driver, and then click Next.
  • HP Deskjet 9800 by selecting in the list or the Deskjet 990c printer, click Next, Finish, and apply the settings. (you can always go back and revert to the original printer driver)

  What version of Word are you using?

  If the problem is resolved and you appreciate my help, please click on the "accept as Solution" and the buttons 'Thumbs Up'. Let me know how make you out. See you soon!

• Printing problem on deskjet 4510 with windows 8.1

  I bought a new deskjet 4510 and have installed via usb on my desktop running windows 8.1. This isn't the impression through products of ms office word, excel etc. and either through wordpad. I can print Notepad files and pdf via adobe reader software.

  I tried HP print and scan doctor who did not find any problem with the printer and print a test page.

  I tried uninstalling and reinstalling, setting the printer wireless to the top but could not do print.

  I looked at the help on this forum and also tried selective installation, disabling all services except when starting microsoft services, but the problem remains.

  Help, please.

  Hey @rshri7869.

  Welcome to the Forums of HP Support!
  
  I understand that you meet your HP Deskjet printing problems in advantage 4510 series e-all-in-one printer to your computer Windows 8.1. You have included a large number of useful information in your post, so thank you. After reviewing the troubleshooting you have already finished, I came to the conclusion that what you feel is a conflict of driver on your computer Windows 8.1. To fix this please follow the steps below.

  How to add another driver:

  1. Open the Start screen (by selecting the windows start button in the lower left corner or by selecting the "Windows" button at the bottom left of your keyboard to the left of the 'Ctrl' key
  2. In the start screen, type "Devices and printers"
  3. If the option devices and printers automatically fills, click settings at the top right and then click on devices and printers.
  4. In the devices and printers folder right click on your series Deskjet 4510 and left click on printer properties
  5. Left click on the Advanced tab
  6. Left-click on new driver
  7. When the new window driver opens just hit 'next' until you see a list of manufacturers on the left and a list of printers on the right.
  8. Select HP as the manufacturer on the left
  9. DeskJet 9800 select the printer on the right. If Deskjet 9800 is only select "Windows Update" at the bottom left and once the update has been completed, you will be able to select Deskjet 9800.
  10. After selecting Deskjet 9800 hit next complete the new driver Wizard
  11. Under the printer properties window, select 'Apply' but do not hit OK
  12. Select the general tab
  13. Rename your printer in HP Deskjet 4510
  14. Click OK
  15. Finally, right-click on your Deskjet 4510 series once more and click on Printing Preferences
  16. Left click on the paper/quality tab
  17. Left click on the dropdown 'Normal' for the print quality down to the right and change its normal fast
  18. Press apply and OK
  19. Try to print!

  Please let me know if the steps I have provided to resolve your problem. Good luck!